Hyperelastic stability landscape: A check for Hill stability of isotropic, incompressible hyperelasticity depending on material parameters
Herbert Baaser, University of Applied Sciences Bingen, Germany · 2025
Read Hyperelastic stability landscape: A check for Hill stability of isotropic, incompressible hyperelasticity depending on material parameters by Herbert Baaser, University of Applied Sciences Bingen, Germany (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2511-13792.txt.
Introduction
Herbert Baaser gives a uniform analytic check for the stability of isotropic, incompressible hyperelastic material models. Stability here means the Hill condition: the material modulus in the stress and log-strain relation must stay positive definite. For incompressible response, every possible deformation sits between uniaxial and biaxial states, with shear in between, a fact made plain in the invariant plane.
Baaser uses that same plane to draw stable and unstable regions for any chosen strain energy function and parameter set. Some fits that look stable in simple tension turn unstable in shear, which would poison a finite element run before it starts. The check gives modelers a standard early warning before simulation.
Catalog record
| CREATOR | Herbert Baaser, University of Applied Sciences Bingen, Germany |
|---|---|
| YEAR | 2025 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 86 KB |
| VERSION | 1.0 |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2511-13792
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
Hyperelastic stability landscape: A check for Hill stability of isotropic, incompressible hyperelasticity depending on material parameters Herbert Baaser, University of Applied Sciences Bingen, Germany Abstract In this paper, we describe a uniform and standardized approach for analytically verifying the stability of isotropic, incompressible hyperelastic material models. Here, we address stability as fulfillment of the Hill condition – i.e. the positive definiteness of the material modulus in the Kirchhoff stress – log–strain relation. For incompressible material behavior, all mathematically and mechanically possible deformations lie within a range bounded, on the one hand, by uniaxial states and, on the other hand, by biaxial states; shear deformation states lie in between. This becomes particularly clear when the possible states are represented in the invariant plane. This very representation is now also used to visualize the regions of unstable material behavior depending on the selected strain energy function and the respective data set of material parameters. This demonstrates how, for some constellations of energy functions, with appropriate selection or calibration of parameters, stable and unstable regions can be observed. If such cases occur, it is no longer legitimate to use them to initiate, for example, finite element simulations. This is particularly striking when, for example, a fit appears stable in uniaxial tension, but the same parameter set for shear states results in unstable behavior without this being specifically investigated. The presented approach can reveal simple indicators for this. Nevertheless, the simple shear deformation, where the principal axes lag behind the deformation γ = tan α \gamma=\tan\alpha of the shear angle α \alpha , i.e. the rotation tensor R ≠ I \hbox{\bf R}\neq\hbox{\bf I} , still represents a special case that requires extra investigations. This is especially true given that all shear components of the logarithmic strains themselves exhibit a non–monotonic behavior with respect to the deformation angle. 1 Introduction The representation of classical isotropic hyperelasticity as a function of the input variables in the form of deformation invariants, see [ 17 ] , or of the stretches themselves, see [ 33 ] , is still of importance, especially when – as here – stability statements of the models are concerned when used in the context of the finite element method (FEM). The special case of quasi– incompressibility is treated as a constraint within the framework of FEM, see modern textbooks such as [ 42 ] or more recent literature, but it is very well suited in this context to analytically describe the procedure and to identify specific properties of the models. In this context of material parameter calibration, we limit ourselves exclusively to ideal–incompressible deformation states. Elastomers in technical products for vibration control and sealing technology are frequently mentioned as a class of materials that exhibit almost ideal incompressibility. This work can be read in series with [ 7 ] and [ 8 ] , where ”three natural strain invariants” K_{1}=\log J as ”amount–of–dilatation”, K_{2}=\|{\rm dev}\log\hbox{\bf v}\rVert as ”magnitude–of–distortion” and K_{3}=\frac{3\sqrt{6}}{K_{2}}\det({\rm dev}(\log\hbox{\bf v})) as ”mode–of–distortion” are proposed based on the left polar decomposition of the deformation gradient \hbox{\bf F}=\hbox{\bf v}\cdot\hbox{\bf R} , see [ 32 ] , with J=\det\hbox{\bf F} in order to specify hyperelastic deformation modes alternatively. In that sense, one can distinguish the prototype deformation modes from each other by K_{3}=0 for pure shear, K_{3}=1 for uniaxial tension and K_{3}=-1 for equibiaxial tension. In a similar way, it was also possible in [ 5 ] to find a formulation that depends significantly only on the stretch in the tensile direction and is used here because this representation allows a further derivation of the stress in a simple way. Starting from the general representation of the standard invariants \displaystyle I_{1} \displaystyle= \displaystyle\lambda_{1}^{2}+\lambda_{2}^{2}+\lambda_{3}^{2}\,, (1) \displaystyle I_{2} \displaystyle= \displaystyle\lambda_{1}^{2}\lambda_{2}^{2}+\lambda_{1}^{2}\lambda_{3}^{2}+\lambda_{2}^{2}\lambda_{3}^{2}\,, \displaystyle I_{3} \displaystyle= \displaystyle\lambda_{1}^{2}\,\lambda_{2}^{2}\,\lambda_{3}^{2}=:J^{2} as a function of the stretches \lambda_{1,2,3} and its specification for the incompressible case with J:=\det\hbox{\bf F}\equiv 1 and \lambda_{3}=(\lambda_{1}\,\lambda_{2})^{-1} as \bar{I}_{1}=\lambda_{1}^{2}+\lambda_{2}^{2}+\frac{1}{\lambda_{1}^{2}\,\lambda_{2}^{2}}\quad{\rm and}\quad\bar{I}_{2}=\lambda_{1}^{2}\lambda_{2}^{2}+\frac{1}{\lambda_{1}^{2}}+\frac{1}{\lambda_{2}^{2}} (2) we directly obtain \bar{I}_{1,m}=\lambda^{2}+\lambda^{2m}+\lambda^{-2m-2}\quad{\rm and}\quad\bar{I}_{2,m}=\lambda^{-2}+\lambda^{-2m}+\lambda^{2m+2} (3) as functions of an (uniaxial) stretch (intensity) \lambda and an additional parameter m=[-\frac{1}{2}...0...1] to specify the deformation mode uniaxial tension ( m=-\frac{1}{2} ), pure shear ( m=0 , often called plane strain ) and equibiaxial tension ( m=1 ), respectively. This ends up in the representation of the modes as boundary lines of all possible deformations in case of incompressibility in the plane of invariants , following e.g. [ 39 ] . In the Appendix A.2 we give more details on this graphical representation. In [ 3 ] and recently in [ 18 ] based on [ 43 ] , a very useful representation of the three squared stretches \lambda_{1}^{2},\lambda_{2}^{2},\lambda_{3}^{2} as functions of the classical invariants I_{1},I_{2} is given for incompressible hyperelasticity in analytical form, i.e. J=\lambda_{1}\lambda_{2}\lambda_{3}\equiv 1 or I_{3}=J^{2}=1 , equivalently. In addition, here we give an equivalent representation and conversion of any given incompressible deformation state \lambda_{1}^{2},\lambda_{2}^{2},\lambda_{3}^{2} or \bar{I}_{1},\bar{I}_{2} into the ( \lambda,m ) representation given above, see Appendix A.1 for a short description and derivation of that closed form representation — to the knowledge of the author for the first time. In consequence, any given representation \lambda_{1}^{2},\lambda_{2}^{2},\lambda_{3}^{2} with \lambda_{1}\lambda_{2}\lambda_{3}\equiv 1 or \bar{I}_{1},\bar{I}_{2} can be converted into each other, in both directions, as needed. In this series there are also new investigations [ 23 ] on the stability specifically for the Mooney–Rivlin model, which is also used here, where, among other things, the relationship between the two material parameters of this model is investigated. There, stability in the three prototype deformation modes from above is defined as positive slope of the Cauchy stress versus the relevant stretch \lambda , i.e. the Cauchy stress–stretch curve must be monotone increasing. Here, an analogue representation of isotropic hyperelasticity is given in a general form, in the sense that the three prototype deformations (uniaxial tension, shear and equibiaxial tension) are formulated uniformly based on ( 3 ). From this, a map of possible regions of material stability is developed, following the stability criteria in modern FEM codes such as Abaqus or Ansys , see [ 2 ] : the application of the Hill stability criterion 1 1 1 In Abaqus denoted vaguely as material stability or Drucker stability criterion with respect to the references given therein. The Drucker criterion is best known in geometrically linearized elasticity as {\rm d}\boldsymbol{\sigma}:{\rm d}\boldsymbol{\varepsilon}>0\Longleftrightarrow\left<\boldsymbol{\sigma}(\boldsymbol{\varepsilon}_{1})-\boldsymbol{\sigma}(\boldsymbol{\varepsilon}_{2}),\boldsymbol{\varepsilon}_{1}-\boldsymbol{\varepsilon}_{2}\right>>0\quad\forall\,\boldsymbol{\varepsilon}_{1}\neq\boldsymbol{\varepsilon}_{2} expressing the convexity of the strain energy in the infinitesimal strain \varepsilon=\frac{1}{2}[\nabla\hbox{\bf u}+(\nabla\hbox{\bf u})^{\rm T}] as symmetrized gradient of the field of displacements \hbox{\bf u}=[u_{1}\,u_{2}\,u_{3}]^{\rm T} with \nabla\hbox{\bf u}=\frac{\partial u_{i}}{\partial x_{j}} in three–dimensional space ( i,j=1,2,3 ). For linear isotropy, this Drucker criterion amounts to \mu>0,\kappa>0 , where \mu is the shear modulus, and \kappa is the bulk modulus. for general, incompressible hyperelastic models formulated as a potential function in \bar{I}_{1} and \bar{I}_{2} or equivalently in \lambda_{1,2,3} , as already given in [ 9 ] based on [ 14 ] . It must be mentioned that deformations with rotating principal axes, such as simple shear , are indeed included in the consideration of the plane of invariants (see [ 5 ] ), but cases of non–monotone Cauchy stress behavior can certainly be shown there, which will be discussed further, see [ 30 ] , [ 41 ] and a simple example in Appendix E . The aim of this work is to consistently