Neutron Interaction Properties of Structural Materials for Multi-Grid Neutron Detectors
A. Backis, C.-C. Lai, M. Aouane, P.P. Deen, K.G. Fissum, J.R.M. Annand, K. Livingston, D. Raspino · 2025
Read Neutron Interaction Properties of Structural Materials for Multi-Grid Neutron Detectors by A. Backis, C.-C. Lai, M. Aouane, P.P. Deen, K.G. Fissum, J.R.M. Annand, K. Livingston, D. Raspino (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2511-02512.txt.
Introduction
A. Backis and seven co-authors measure how candidate shielding materials interact with neutrons, for a spectrometer being built at the European Spallation Source. The T-REX instrument will detect scattered thermal neutrons with Multi-Grid detectors, thin boron carbide coatings on aluminium blades. Internal shielding is needed to stop neutrons scattering more than once inside the detector and blurring the data. A Monte Carlo study had shortlisted materials; this work tests twelve of them at the ISIS neutron source.
Transmission was measured across a range of wavelengths with a position-sensitive detector, and scattering was measured for six samples on a second instrument. The tests identify a boron carbide and aluminium composite, plated with nickel to suppress its own alpha-particle background, as an effective neutron absorber. The authors conclude it is suitable for building into the Multi-Grid structures of inelastic neutron spectrometers.
Catalog record
| CREATOR | A. Backis, C.-C. Lai, M. Aouane, P.P. Deen, K.G. Fissum, J.R.M. Annand, K. Livingston, D. Raspino |
|---|---|
| YEAR | 2025 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 24 KB |
| VERSION | 1.0 |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2511-02512
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
Neutron Interaction Properties of Structural Materials for Multi-Grid Neutron Detectors A. Backis, C.-C. Lai, M. Aouane, P.P. Deen, K.G. Fissum, J.R.M. Annand, K. Livingston, D. Raspino Abstract The T-REX neutron time-of-flight spectrometer at the European Spallation Source will use Multi-Grid Technology, which relies on thin B 4 C {\normalsize\mathrm{B_{4}C}} coatings on the Al blades of the grids to detect scattered thermal neutrons. Following a Monte Carlo study of internal shielding to suppress neutron multiple scattering in T-REX, the neutron transmission and scattering properties of 12 shielding-material samples have been measured at the ISIS spallation neutron source. Neutron transmission was measured on the EMMA beam line at wavelengths 0.5-4.7 Å, using a 2D-position-sensitive, neutron GEM detector, while neutron scattering was measured for 6 of the samples at the Merlin spectrometer, at wavelengths 0.72, 1.28, 1.85 and 2.41 Å. The present tests show that a B 4 C {\normalsize\mathrm{B_{4}C}} /Al composite material, plated with Ni to stop intrinsic alpha background, is an effective neutron absorber, suitable for incorporation in the Multi-Grid structures which detect the neutrons in inelastic neutron spectrometers . 1 Introduction Figure 1: Left: prototype T-REX grid. Each voxel has an internal dimension of 23.5 mm (x) by 24.0 mm (y) by 9.5 mm (z). Right: 3D view of a 12-grid T-REX prototype, with outer sections cut away to reveal the internal structure. Multi-Grid (MG) technology for detection of sub-eV neutrons, originally developed at ILL [ 1 ] , will be used in the T-REX bispectral chopper spectrometer which is under construction at the European Spallation Source (ESS) [ 2 ] . The Multi-Grids are stacks of grids, each a rectangular lattice of normal and radial Al blades (Fig. 1 ). The grids form the cathodes of a voxelised proportional counter (VPC), with wires strung through the centres of each grid voxel providing the anodes. The normal blades are coated with \mathrm{{}^{10}B} -enriched \mathrm{B_{4}C} , and neutron capture in the \mathrm{B_{4}C} film produces \mathrm{{}^{4}He} and \mathrm{{}^{7}Li} ions, one of which escapes into the VPC gas (e.g. Ar-CO2) giving a detectable signal. Al is the main structural material for both the grids, their support mechanics and the gas containment vessels, as its neutron absorption cross section is relatively low. Nevertheless neutrons can scatter internally in the Al and other nearby materials before they eventually convert and this distorts the time-of-flight (TOF) and angle-of-detection measurement, thereby distorting the energy and momentum-transfer measurement by the spectrometer. Internal neutron scattering can be suppressed by installation of internal shielding [ 3 , 4 , 5 ] , at the sides and rear of the MG and on the radial blades of the grids. Monte Carlo simulations of neutron scattering from Vanadium into T-REX [ 6 ] indicate that internal shielding materials based on \mathrm{B_{4}C} can result in a major reduction in internal scattering within the spectrometer. Scintered \mathrm{B_{4}C} sheet would be a possibility for side and rear shields, but structurally this is a difficult material and it is unsuitable for radial blades, which must be electrically conductive. A number of materials containing \mathrm{B_{4}C} are available and their shielding effectiveness has been investigated using the Geant4 [ 7 ] model of T-REX. Subsequently neutron transmission and scattering properties of good candidate shielding materials were measured at the EMMA [ 8 ] and MERLIN [ 9 ] beam lines of the neutron-spallation facility ISIS and compared to Geant4 simulations of these test measurements. 2 Neutron Transmission Tests at EMMA Figure 2: Left: schematic diagram of the EMMA neutron transmission test. Right: comparison of sample in/out wavelength spectra derived from TOF at the nGEM detector. The sample was BA31-3 (see Table 1 ). Measurements of neutron transmission through samples of shielding material were performed on the EMMA beam line, with the Fermi chopper powered down to produce a white neutron beam. A schematic of the experimental setup is shown in Fig. 2 (left plot), while the neutron wavelength spectrum is displayed in Fig. 2 (right plot, sample out). The samples are listed in Table 1 . The neutron beam was collimated by movable \mathrm{B_{4}C} jaws, set to produce a rectangular aperture of 25\times 50\>\mathrm{mm^{2}} . It then passed through a low efficiency beam monitor (BM), the sample under study, and a 2D, position-sensitive neutron gas electron multiplier (nGEM) detector [ 10 ] . The BM was a 0.25 mm sheet of GS1 scintillating glass, with a neutron efficiency of \sim 0.5 % at a wavelength of \sim 1 Å. The nGEM was a 10\times 10\>\mathrm{mm^{2}} GEM chamber read out by 128 x and 128 y strips (0.8 mm pitch), with a thin layer of \mathrm{{}^{10}B} deposited on the cathode to convert neutrons to detectable ions. The intersections between x and y strips define 16384 pixels. TOF was recorded for the nGEM strips and BM. Samples were rectangular sheets of the material under study inserted into the neutron beam, downstream of the BM and perpendicular to the beam direction. Name Substrate Coating \mathrm{B_{4}C} (%) \mathrm{{}^{10}B} (%) Slope \pm 5 % G4 k Al HP Al 0.5 mm – – – 0.00 0.00 Al-5 HP Al 0.5 mm Sputtered \mathrm{B_{4}C} 5 \mu m 100 97 0.18 0.23 0.23 Dr-10 Al 0.5 mm Drip \mathrm{B_{4}C} /Epoxy 10 \mu m 73.8 92 0.47 0.25 0.25 Dr-20 Al 0.5 mm Drip \mathrm{B_{4}C} /Epoxy 20 \mu m 73.8 92 1.04 0.50 0.50 Sp1.4 Al 1 mm Sprayed \mathrm{B_{4}C} /Al 300 \mu m 52 19.9 0.56 1.41 1.39 Sp1.6 Al 1 mm Sprayed \mathrm{B_{4}C} /Al 300 \mu m 52 19.9 1.19 1.41 1.39 BA31-1 \mathrm{Al/B_{4}C} 1 mm – 31 19.9 1.54 1.52 1.51 NiBA31-1 \mathrm{Al/B_{4}C} 0.95 mm Plated Ni 25 \mu m 31 19.9 1.43 1.45 1.43 BA31-2 \mathrm{Al/B_{4}C} 2 mm – 31 19.9 3.06 3.03 3.03 BA31-3 \mathrm{Al/B_{4}C} 3 mm – 31 19.9 4.55 4.59 4.54 BA25-3 \mathrm{Al/B_{4}C} 3 mm – 25 19.9 3.54 3.67 3.68 BA25-8 \mathrm{Al/B_{4}C} 8 mm – 25 19.9 9.54 9.93 9.82 Table 1: Shielding candidate materials. Column ‘Substrate’ is the substrate material of the sample where HP stands for High Purity. Coating (if applied) is the coating applied to the substrate. ‘ \mathrm{B_{4}C}(\%) ’ is the content by weight of \mathrm{B_{4}C} in the substrate or coating and ‘ \mathrm{{}^{10}B} (%)’ is the \mathrm{{}^{10}B} content (19.9% in natural B). Slope is the exponential decay constant fitted to the averaged R_{io} transmission measurement displayed in Fig. 3 . G4 is the decay constant fitted to the Geant4 calculation and k=2133N_{10}t is a hand calculation (see text) of the decay constant, based on a \mathrm{{}^{10}B} capture cross section [ 13 ] \sigma=2133\lambda_{n} b. Runs were made with sample in and sample out, for equal accumulations of proton charge on the spallation target. Counts in the nGEM pixels were normalised to equal neutron counts in the beam monitor and the ratio ( R_{io} ) of sample-in/sample-out counts gives a measure of the neutron transmission probability through the sample. Fig. 3 displays R_{io} , averaged over the area of the sample, as a function of neutron wavelength \lambda_{n} , Those nGEM pixels at the edges of the sample shadow and those pixels showing the slots in the sample (see Fig. 4 ) were omitted from the averaging procedure. If neutron capture on