Bimorph Lithium Niobate Piezoelectric Micromachined Ultrasonic Transducer
Ziqian Yao, Vakhtang Chuluhadze, Zihuan Liu, Xiaoyu Niu, Tzu-Husan Hsu, Byeongjin Kim, Neal Hall, and Ruochen Lu · 2025
Read Bimorph Lithium Niobate Piezoelectric Micromachined Ultrasonic Transducer by Ziqian Yao, Vakhtang Chuluhadze, Zihuan Liu, Xiaoyu Niu, Tzu-Husan Hsu, Byeongjin Kim, Neal Hall, and Ruochen Lu (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2509-00600.txt.
Introduction
Ziqian Yao leads a team of eight authors who built a tiny ultrasound device. The device is a transducer. It turns electric signals into sound above human hearing. The design uses lithium niobate crystal. That crystal bends when voltage is applied to it. Two layers with opposed polarity form the active stack.
The team makes this bimorph stack from a transferred, periodically poled film. The stack drives a bending mode of vibration. That mode sits near one megahertz. Laser tools then measure the motion of the device surface. The measurements confirm the design models. They show strong center motion per volt of drive. The result points to a compact platform for high-grade ultrasound work.
Catalog record
| CREATOR | Ziqian Yao, Vakhtang Chuluhadze, Zihuan Liu, Xiaoyu Niu, Tzu-Husan Hsu, Byeongjin Kim, Neal Hall, and Ruochen Lu |
|---|---|
| YEAR | 2025 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 11 KB |
| VERSION | 1.0 |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2509-00600
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
Bimorph Lithium Niobate Piezoelectric Micromachined Ultrasonic Transducer Ziqian Yao, Vakhtang Chuluhadze, Zihuan Liu, Xiaoyu Niu, Tzu-Husan Hsu, Byeongjin Kim, Neal Hall, and Ruochen Lu Abstract This work demonstrates a prototype bi-layer piezoelectric micromachined ultrasonic transducer (PMUT) based on transferred periodically poled piezoelectric film (P3F) X-cut lithium niobate (LN). Opposite in-plane polarizations in the piezoelectric film stack are employed to enable efficient lateral field excitation of the flexural mode. Thanks to its high piezoelectric coefficient and low dielectric loss, the X-cut LN exhibits high figure of merits (FoMs) as both sensors and transducers. The fabricated PMUT demonstrates an out-of-plane mode near 1 MHz with an electromechanical coupling of 3.6%. Laser Doppler vibrometry further validates the finite element analysis, showing a peak center displacement of 8nm /V. These results establish bi-layer P3F LN PMUTs as a promising platform for compact and high-performance ultrasonic transducers. Future work will focus on theoretical analysis, modeling of the measured data, improving the design of the transducer topology, and mitigating feedthrough effects. I Introduction Piezoelectric micromachined ultrasonic transducers (PMUTs) enable compact ultrasonic sensing and actuation using flexural vibration of thin piezoelectric films. Unlike capacitive micromachined ultrasonic transducers (CMUTs), PMUTs eliminate DC bias requirements and offer linear electromechanical conversion [ 1 , 2 ] , allowing simpler drive electronics and higher output at low voltages. Advancements in thin-film platforms such as sputtered AlN/ScAlN [ 3 , 4 , 5 , 6 ] , and PZT [ 7 , 8 , 9 ] have enabled PMUT applications in medical imaging [ 10 , 11 ] , wireless communications [ 12 , 13 ] , fingerprint recognition [ 14 , 15 ] , and flow sensing [ 16 , 17 ] . However, achieving strong performance in both transmission and reception remains a key challenge for PMUTs, largely limited by the electromechanical properties of the piezoelectric material. Recent efforts have explored piezoelectric materials with improved coupling and lower acoustic loss [ 18 , 19 , 20 ] . To enable fair comparison between piezoelectric materials regardless of transducer geometry, transmitter and receiver figure-of-merits (FoMs) have been developed [ 18 ] . Table I summarizes these FoMs for widely used PMUT materials, including AlN, ScAlN, and PZT. To characterize the electrical output generated by mechanical deformation in flexural transducers, several figure-of-merits (FoMs) are defined. The piezoelectric coefficient e (C/m 2 ) quantifies the induced surface charge per unit stress, representing current and charge sensitivity. In contrast, the ratio e/\varepsilon (GV/m) reflects voltage sensitivity by accounting for dielectric constants from the material’s permittivity \varepsilon . To evaluate detection performance under low-signal conditions, the FoM e/\sqrt{\varepsilon\tan\delta} , where \tan\delta is the dielectric loss tangent. A higher value indicates improved signal-to-noise ratio (SNR) in receiver-limited systems. For transducer applications, a large electromechanical coupling coefficient ( k^{2} ) is essential to maximize energy conversion between electrical and mechanical domains. In flexural-mode devices with a bending layer, this efficiency is quantified by the transducer FoM e^{2}/(\varepsilon Y) , which captures bidirectional energy transfer. Here, Y represents the stiffness of the passive layer, normalized to the Young’s modulus of silicon [ 18 ] . Among the materials listed in Table I , PZT and PMN-PT exhibit high k^{2} , making them favorable for transducer applications. However, their large dielectric constant and high dielectric loss significantly degrade their performance as sensors, leading to poor voltage sensitivity and high noise levels. This trade-off highlights the need to explore alternative piezoelectric materials with balanced properties that support strong electromechanical coupling while maintaining low dielectric losses, which enables improved performance in both sensing and transmitting modes. Lithium niobate (LN), with its high piezoelectric coefficients and low dielectric loss [ 21 , 22 ] , has emerged as a strong candidate for next-generation PMUTs. Previous work [ 23 ] has demonstrated promising PMUT performance using single-layer 36°Y-cut LN under lateral-field-excitation (LFE). Building on this, this work introduces a multilayer periodically poled piezoelectric film (P3F) structure, fabricated through the high-quality transfer of single-crystal LN. By utilizing a bimorph X-cut LN structure with alternating crystal orientations, this approach fully harnesses LN’s advantageous FoMs for both sensing and actuation. TABLE I: Sensor and Transducer FoMs of Piezoelectric Materials Material Ref. Sensor FoMs Transducer FoM e (C/m 2 ) e/\varepsilon (GV/m) e/\sqrt{\varepsilon\tan\delta} (10 6 (J/m 3 ) 1/2 ) e^{2}/(\varepsilon Y) PZT [ 24 ] 18.7 1.30 1.10 0.19 PMN-PT [ 24 ] 26.0 1.90 0.84 0.38 AlN [ 22 ] 0.68 6.99 2.20 0.04 Sc 0.3 AlN [ 25 ] 2.25 12.7 3.10 0.22 Y-LN [ 26 ] 2.43 6.24 3.43 0.04 X-LN [ 26 ] 4.65 13.13 6.85 0.47 II Design and Simulation Fig. 1: (a) Top view cross-section of the lateral field excited bimorph X-cut LN PMUT. (b) Optical image of the fabricated suspended LN PMUT with top electrodes labeled as VIN and GND. The proposed bimorph X-cut PMUT top view is shown in Fig. 1 with key parameters labeled. As shown in Fig. 1 (a), the device is composed of a suspended trilayer stack consisting of two 10 \mu m thick X-cut LN layers and a 400 nm SiO 2 interlayer on top of a Si carrier wafer. The bottom LN layer is rotated in-plane by 180 ∘ , forming a P3F structure that reverses the polarization axis (Z) orientations. This configuration promotes constructive charge buildup across the bimorph stack while suppressing undesired overtones through charge cancellation from opposing stress phases, thereby improving out-of-plane actuation [ 27 , 28 ] . Two pairs of 100 nm platinum (Pt) electrodes are patterned on the top surface for flexural mode excitation. The underlying Si is removed beneath the active region to create a suspended cavity, providing mechanically free boundaries for acoustic displacement. Fig. 1 (b) shows an optical image of the fabricated device, where a 700~\mu\text{m}\,\times\,700~\mu\text{m} cavity region is clearly visible with a suspended membrane on top, along with the patterned metal electrodes labeled as VIN and GND. The device structure is first analyzed using COMSOL finite element analysis (FEA). As shown in Fig. 2 (a–b), a lateral electric field applied across the top electrodes induces in-plane stress ( T_{x} ) in the LN layers through the strong e_{11} coefficient (4.65 C/m 2 ). Because the bimorph LN stack has reversed Z-axis orientations, the two layers generate stresses of opposite sign under the same field, which add constructively across the thickness to enhance out-of-plane displacement. The film stack, consisting of 10 µm LN and 2 \mu m SiO 2 , is designed to prevent charge cancellation and maximize electromechanical coupling. Electrodes are alternately biased and placed near stress antinodes, while the outer electrodes extend beyond the suspended region to improve energy transfer. The simulated admittance spectrum in Fig. 2 (c) shows a clear resonance around 1.1 MHz, corresponding to an effective coupling of 3.6 %, which is higher than reported ScAlN counterparts [ 29 , 30 ] . The static capacitance ( C_{0} ) is extracted as 0.099 pF and the quality factor ( Q ) is set to be 20. Meanwhile, Fig. 2 (d) plots the dynamic displacement, peaking at 3.27 nm/V near resonance, highlighting the strong out-of-plane vibration. Fig. 2: Finite-element simulation of the bimorph X-cut LN PMUT: (a) 3D displacement mode