Ion adsorption and zeta potential of hydrophobic interfaces

Yuki Uematsu · 2025

Read Ion adsorption and zeta potential of hydrophobic interfaces by Yuki Uematsu (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2508-13737.txt.

Introduction

Yuki Uematsu reviews how ions gather at water-repelling surfaces in a 2025 chapter. Hydrophobic interfaces appear in foods, cosmetics, soaps, and coatings. Their electrical charge in water, measured as zeta potential, steers how products mix and stay stable.

Long habit treats solid, liquid, and gas interfaces with water as electrically alike. A careful comparison of published data shows real differences among the three. Hydrogen ions seem to cling to all such surfaces more strongly than hydroxide ions. Proof for that ranking is still thin for liquid and solid surfaces. The chapter calls for targeted measurements to settle the ordering. Getting it right matters wherever bubbles, droplets, or coated particles must behave predictably in water.

Catalog record

CREATORYuki Uematsu
YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE36 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2508-13737

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Ion adsorption and zeta potential of hydrophobic interfaces Yuki Uematsu Abstract Hydrophobic interfaces have unique physicochemical properties and are used in various chemical products such as food, cosmetics, soap, and medicine and technologies such as pan coating and ski wax. In this chapter, we describe the fundamental concept of hydrophobic interfaces and explain their ion adsorption and zeta potential by using experimental data from the literature. Thus far, these electrical properties are considered universal for solid/water, liquid/water, and gas/water interfaces; however, a careful comparison in this chapter will reveal significant differences among them. To confirm that the affinity of H + \mathrm{H^{+}} ions for all hydrophobic interfaces is stronger than that of OH − \mathrm{OH^{-}} ions, more experimental data on hydrophobic liquid/water and solid/water interfaces are required. Keywords: contact angle, electrolyte, hydrophobic surface, interfacial tension, ion adsorption, pH, polytetrafluoroethylene, surface charge, surface tension, water interface, water autoionization, zeta potential † † itembox-title: Key points/objectives box • The concept of hydrophobic interfaces is broad for solid/water, liquid/water, and gas/water interfaces. • A careful comparison reveals that the ion adsorption and zeta potential of hydrophobic interfaces are not universal for solid/water, liquid/water, and gas/water interfaces. • More experimental data on hydrophobic liquid/water and solid/water interfaces are required to confirm whether the affinities of \mathrm{H^{+}} and \mathrm{OH^{-}} ions are universal for all hydrophobic interfaces. I Introduction Hydrophobic interfaces are ubiquitous in nature and are used in technological applications such as pan coating and ski wax Israelachvili 2011 ; Uematsu et al. 2019 . The hydrophobic interfaces generally have common properties, for example, chemical inertness, water repellency, and low friction. The concept of hydrophobic interfaces can be applied not only to solid/water interfaces but also to liquid/water and gas/water interfaces. However, hydrophobic and hydrophilic fluid interfaces cannot be distinguished easily because the contact angle in these interfaces is not well defined. Hydrophobic interfaces have the universal property of chemical inertness against water, and thus, the surface charge is governed by the physical ion adsorption. When acids and bases are added to these hydrophobic interfaces, the resultant difference in the surface tension demonstrates that the physical adsorption of \mathrm{H^{+}} ions is stronger than \mathrm{OH^{-}} ions. However, the zeta potentials of polytetrafluoroethylene (PTFE) surfaces, oil droplets, and gas bubbles suggest that all hydrophobic interfaces are negatively charged. The physical chemistry community is well aware of this contradiction of hydrophobic surfaces being electrically positively vs negatively charged, and therefore, this topic is highly debated Uematsu et al. 2020 ; Poli et al. 2020 . Notably, the \mathrm{H^{+}}>\mathrm{OH^{-}} ion affinity strength for hydrophobic interfaces has been demonstrated only for air/water interfaces thus far and not for liquid/water or solid/water interfaces. In this chapter, we describe hydrophobic surfaces and their characteristics, ion adsorption, and zeta potentials based on experimental data from the literature. In particular, we discuss the differences between the solid/water, liquid/water, and gas/water hydrophobic interfaces as this aspect has not been sufficiently explored by researchers thus far. A careful comparison of the hydrophobic interfaces reported in the literature revealed a lack of experimental data for liquid/water and solid/water interfaces, even though it is a simple and important system. II Hydrophobic interfaces Figure 1: Schematic of the contact angle ( \theta ) of a solid/water hydrophobic interface. A flat solid surface is defined as a hydrophobic interface/surface only if its contact angle with a water droplet is greater than 90^{\circ} . The equilibrium contact angle \theta of a water droplet on a flat solid surface, as shown in Fig. 1 , is defined by Young’s equation, as follows: \cos\theta=\frac{\gamma_{\mathrm{s}}-\gamma_{\mathrm{s/w}}}{\gamma_{\mathrm{w}}}, (1) where \gamma_{\mathrm{s}} is the surface tension of the solid, \gamma_{\mathrm{s/w}} is the interfacial tension at the solid/water interface, and \gamma_{\mathrm{w}} is the surface tension of water. The subscript s denotes a solid, and the subscript w denotes water. Technically, \gamma_{\mathrm{s}} and \gamma_{\mathrm{w}} are the interfacial tensions at the solid/air and water/air interfaces, respectively, where the air phase is saturated with the vapor of the droplet solution. However, to simplify the parameters, it is assumed that the air phase does not affect the interfacial tension, and hence, \gamma_{\mathrm{s}} and \gamma_{\mathrm{w}} are denoted as the surface tensions of the solid and water, respectively. The water surface tension is \gamma_{\mathrm{w}}=72.0\, mN/m at 1\, atm and 298\, K Haynes 2017 . The hydrophobic condition of \theta>90^{\circ} implies that \gamma_{\mathrm{s/w}}>\gamma_{\mathrm{s}} , which indicates that the interfacial tension at the solid/water interface is larger than the surface tension of the solid. The contact angle is useful for characterizing the wetting properties of solid surfaces but is insufficient for determining both \gamma_{\mathrm{s}} and \gamma_{\mathrm{s/w}} separately. Currently, a direct method to measure \gamma_{\mathrm{s}} and \gamma_{\mathrm{s/w}} separately is not available, because the solid interface is not easily deformable. To overcome this issue, the phenomenological decomposition of the interfacial tension to the respective surface tensions is often considered Oss et al. 1988 . However, the decomposition of the interfacial tension is not quantitatively reliable or predictive. Another difficulty is the contact angle hysteresis. In general, the receding (minimum) and advancing (maximum) contact angles measured differ from the equilibrium contact angle. The advancing contact angles of the solid surfaces are listed in Table 1 . The contact angles of inert polymers exceed 90^{\circ} , that of graphite is nearly 90^{\circ} , and that of polymethylmethacrylate (acrylic resin) is smaller than 90^{\circ} . Glass exhibits zero or an extremely small contact angle. Table 1: Advancing contact angles and surface tension differences ( \gamma_{\mathrm{s/w}}-\gamma_{\mathrm{s}} ) of various solid materials Adamson and Gast 1997 . \gamma_{\mathrm{s/w}}-\gamma_{\mathrm{s}} is calculated using \gamma_{\mathrm{w}}=72.0\, mN/m. material contact angle ( ∘ ) \gamma_{\mathrm{s/w}}-\gamma_{\mathrm{s}} (mN/m) paraffin 110 24.6 PTFE 1 1 1 polytetrafluoroethylene 106 2 2 2 average of numbers listed in pp 365 of Ref. 7 . 19.8 polyethylene 95 2 6.3 graphite 86 -5.0 PMMA 3 3 3 polymethylmethacrylate 59 -37.1 glass small - The definition of a hydrophobic surface based on the contact angle is applicable only for solids. However, it can be extended to liquid/water interfaces even though contact angles cannot be measured for those. A liquid/water interface is defined as hydrophobic only if the interfacial tension of the liquid/water interface ( \gamma_{\mathrm{l/w}} ) is larger than the liquid surface tension ( \gamma_{\mathrm{l}} ). For immiscible liquid/water interfaces, all the surface and interfacial tensions, \gamma_{\mathrm{l/w}} , \gamma_{\mathrm{l}} , and \gamma_{\mathrm{w}} , can be measured experimentally. For example, most liquid alkanes ( \mathrm{C_{n}H_{2n+2}} , 5\leq n\leq 17 ) exhibit a surface tension of approximately \gamma_{\mathrm{l}}=20 to 30\, mN/m Haynes 2017 ; Aveyard and Haydon 1965 and liquid/water interfacial tension of approximately \gamma_{\mathrm{l/w}}=50\, mN/m Backes et al. 1990 ; Aveyard and Haydon 1965 , indicating that \gamma_{\mathrm{l/w}}>\gamma_{\mathrm{l}} ; thus, the liquid alkane/water interfaces are hydrophobic. Therefore, the effective contact angles ( \theta_{\mathrm{eff}} ) of these liquids can be defined as \theta_{\mathrm{eff}}=\arccos\left(\frac{\gamma_{\mathrm{l}}-\gamma_{\mathrm{l/w}}}{\gamma_{\mathrm{w}}}\right). (2) Table 2 lists the surface tensions, interfacial tensions against water, and effective contact angles of some liquid alkanes. Fluorocarbon and chlorocarbon/water interfaces as well as the hydrocarbon/water interfaces are hydrophobic. Fatty alcohols ( \mathrm{C_{n}H_{2n+1}OH} ) with n>4 are immiscible with water; however, their effective contact angles are lower than 90^{\circ} , and therefore, they are not hydrophobic. Table 2: Contact angles and surface/interfacial tensions of liquid alkanes at 298\, K and 1\, atm. material

Read the complete text