Wake Stabilization and Force Modulation via Surface Dimples on an Airfoil at Low-Reynolds-Numbers
Putu Brahmanda Sudarsana, Jagmohan Singh, Anchal Sareen · 2025
Read Wake Stabilization and Force Modulation via Surface Dimples on an Airfoil at Low-Reynolds-Numbers by Putu Brahmanda Sudarsana, Jagmohan Singh, Anchal Sareen (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2507-23564.txt.
Introduction
Putu Sudarsana, Jagmohan Singh, and Anchal Sareen tested dimpled wings in detailed flow mock runs in 2025. At slow flight speeds a wing's wake can flap irregularly, shaking lift and drag. The team placed small dimples on the upper side of a standard wing profile at two spots and mock the flow at two low speed settings. The wing held at a fixed tilt.
Dimples farther back calmed force swings strongly at the slower setting. Cutting lift and drag wobble by roughly a quarter and a third, with mean forces barely changed. At the faster setting the same dimples made swings far larger but steady and regular. Streamwise vortices born inside the dimples explain the steadier wake.
Catalog record
| CREATOR | Putu Brahmanda Sudarsana, Jagmohan Singh, Anchal Sareen |
|---|---|
| YEAR | 2025 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 46 KB |
| VERSION | 1.0 |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2507-23564
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
Wake Stabilization and Force Modulation via Surface Dimples on an Airfoil at Low-Reynolds-Numbers Putu Brahmanda Sudarsana, Jagmohan Singh, Anchal Sareen Abstract This study investigates the effect of surface dimples on the unsteady aerodynamics of a National Advisory Committee for Aeronautics airfoil (NACA0012) at a chord-based Reynolds numbers of R e c = 5300 Re_{c}=5300 and 10,000 10{,}000 using direct numerical simulations. Dimples were placed on the suction side at non-dimensional chordwise locations of l D / c l_{D}/c = 0.035 and 0.35, and the flow response was studied at a fixed angle of attack α = 5 ∘ \alpha=5^{\circ} . At R e c = 5300 Re_{c}=5300 , dimples placed at l D / c l_{D}/c = 0.35 reduced lift and drag fluctuations by 26.5% and 33.3%, respectively, with minimal change in mean forces. At R e c = 10,000 Re_{c}=10{,}000 , the same configuration led to a seven-fold increase in force fluctuations, while the mean remained unchanged. The smooth airfoil exhibited irregular, aperiodic force signals at this R e c Re_{c} , whereas the dimpled case showed highly periodic behavior, indicating wake stabilization. Flow visualizations revealed that dimples generate streamwise vortices within the boundary layer. These vortices are found to have a stabilizing effect on wake dynamics at R e c = 5300 Re_{c}=5300 , reducing vortex breakdown and enhancing the coherence of wake structures. Spectral Proper Orthogonal Decomposition (SPOD) showed that dimples redistribute modal energy depending on Reynolds number: at low R e c Re_{c} , they reduce broadband content and suppress unsteadiness, while at high R e c Re_{c} , they amplify dominant shedding modes and broaden the spectral energy distribution. These results demonstrate that dimples can passively modulate unsteady forces and wake dynamics for a flow over a streamlined body, either suppressing or enhancing flow instabilities depending on the regime. 1 Introduction The past decade has seen rapid advancements in small and micro-unmanned aerial vehicles (UAVs). Their high maneuverability and compact size have expanded their applications to include surveillance, ship decoys, and the detection of biological, chemical, and radioactive materials [ 1 ] . These UAVs typically feature an airfoil for lift generation and maneuverability. These vehicles operate at low chord-based Reynolds numbers ( Re_{c}=U_{\infty}c/\nu\leq 10,000 , where c is the chord length and U_{\infty} is the freestream velocity), where the flow is persistently laminar. This limits the airfoil performance compared to the higher Reynolds number [ 2 ] . Therefore, a flow control strategy is necessary at low Re_{c} to enable better performance and maneuverability. One such passive flow control strategy involves surface modifications, such as surface indentations, shaped as dimples, which are widely used in bluff bodies [ 3 , 4 , 5 ] . Dimples transition the boundary layer near the wall from laminar to turbulent and delay flow separation [ 5 , 3 ] . Streamlined bodies, such as airfoils, also exhibit flow separation on the suction side at high angles of attack ( \alpha ). The adverse pressure gradient reduces the flow momentum in the near-wall region and induces instability in the outer boundary layer. It can be reasoned here that dimples will also enable control over the boundary layer transition, which could increase the aerodynamic performance. Several experimental and numerical studies have explored the impact of dimples on the aerodynamic performance of airfoils, although at a much larger Reynolds number. Beves et al. [ 6 ] conducted experiments on an inverted Tyrrell026 airfoil with three rows of dimples at l_{D}/c=0.23 ( l_{D} is the distance of the dimple center from the leading edge of the airfoil) to see if they could suppress flow separation at different heights above ground at a Reynolds number ( Re_{c} ) of 0.5\times 10^{5} . Their boundary layer profile measurements suggested that the dimples not only induced turbulence in the boundary layer, but also generated strong vortices that helped reattach the flow far downstream, reducing wake thickness and mitigating ground-effect interactions. Miller et al. [ 7 ] conducted a boundary layer analysis on a NACA-2412 airfoil with multiple dimple arrays at the upper leading edge. The study found a positive correlation between dimple depth and the extent of boundary layer attachment. Several studies indicate that the optimal placement for sustaining boundary layer attachment is near the leading edge before the laminar separation point [ 8 , 9 ] . However, contrasting findings were reported by Stolt et al. [ 10 ] , who used Tomographic Particle Image Velocimetry (TPIV) to measure the flowfield around NACA0015 airfoil. They found that a full array of dimples placed at 20% of the leading edge did not prevent flow separation at Re_{c}=1\times 10^{5} . These conflicting results highlight the need for further investigations, and complementary numerical studies could offer a more comprehensive understanding of the effects of dimples on airfoils. A laminar separation bubble often forms on the suction side of the airfoil, where the laminar boundary layer encounters an adverse pressure gradient, which leads to flow separation, transition to turbulence, and eventual reattachment. This phenomenon can significantly alter the pressure distribution and degrade aerodynamic performance, particularly at low Reynolds numbers. D’Alessandro et al. [ 11 ] conducted a large eddy simulation (LES) of the NACA64(2)-014A airfoil modified with dimples located at 0.55c with a dimple depth-to-diameter ratio ( d/D ) of 0.15 at Re_{c}=1.75\times 10^{5} . They reported a significant reduction in the extension of the laminar separation bubble when the dimples were placed very close to the flow separation location. For all three angles of attacks tested in their study ( 0^{\circ} , 4^{\circ} , and 8^{\circ} ), dimples were observed to reduce pressure drag and increase viscous drag. Subsequent research on the effect of dimples on NLF(1)-0416 airfoil using LES was carried out by Xie et al. [ 8 ] . They reported drag reductions of up to 43% and 54%, along with lift-to-drag ratio improvements of 337% and more than 280% in Re_{c}=39000 and Re_{c}=68500 , respectively. This was attributed to the formation of a laminar separation bubble due to flow reattachment, in contrast to the smooth baseline case where the flow abruptly separates. A recent study by Ali et al. (2024) used Reynolds-Average Navier-Stokes (RANS) simulations to examine how spherical dimple arrays, both inward and outward, affect the aerodynamic performance of an ONERA M6 wing. They tested the dimples placed at 15%, 50%, and 85% of the wing’s leading edge at Reynolds number, Re_{c}=2.5\times 10^{5} . The results showed that the inward dimples on the suction side of the wing reduced the total drag by up to 6.6% without significantly affecting lift. The researchers attributed this drag reduction mainly to a delay in flow separation caused by the dimples, which primarily affected pressure drag. However, the study did not clarify whether the viscous drag was negatively impacted. Additionally, the use of the RANS method limited the study’s ability to predict the complex flow behaviors induced by dimples. At ultra-low Reynolds number of Re_{c}=5300 , the flow over NACA0012 airfoil is characterized by the absence of any separation bubble and stall condition [ 12 ] . As \alpha increases, the initial fully attached flow becomes partially attached and