Shot-Noise-Limited Laser Frequency Stabilization Using a High-Resolution Wavelength Meter Journal: opticajournal Publication type: Research Article

Mengde Gan, 1,5 Haoyi Zhang, 1,5 Xiaodong Tan, 1,5 Jiaming Li, 1,2,3,4,* Le Luo 1,2,3,4,* · 2025

Read Shot-Noise-Limited Laser Frequency Stabilization Using a High-Resolution Wavelength Meter Journal: opticajournal Publication type: Research Article by Mengde Gan, 1,5 Haoyi Zhang, 1,5 Xiaodong Tan, 1,5 Jiaming Li, 1,2,3,4,* Le Luo 1,2,3,4,* (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2506-20894.txt.

Introduction

A laser whose frequency wanders is useless for precision measurement, and the usual anchors, optical cavities or atomic references, are bulky. Mengde Gan and co-authors lock a 556-nanometer laser instead to a high-precision wavelength meter, closing a feedback loop that reads the meter and corrects the laser continuously. The stability then reaches the meter's own shot-noise limit, the floor set by the graininess of light itself.

The system held the frequency steady to within a few hundred kilohertz over the long term, without any complex optical components. The authors argue that with careful feedback design, wavelength-meter locking is a practical, scalable route for experiments needing long-term stability, and a natural fit for compact or field-deployable instruments.

Catalog record

CREATORMengde Gan, 1,5 Haoyi Zhang, 1,5 Xiaodong Tan, 1,5 Jiaming Li, 1,2,3,4,* Le Luo 1,2,3,4,*
YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE20 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2506-20894

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Shot-Noise-Limited Laser Frequency Stabilization Using a High-Resolution Wavelength Meter Journal: opticajournal Publication type: Research Article Mengde Gan, 1,5 Haoyi Zhang, 1,5 Xiaodong Tan, 1,5 Jiaming Li, 1,2,3,4,* Le Luo 1,2,3,4,* Abstract We present a compact laser frequency stabilization method by locking a 556 nm laser to a high-precision wavelength meter. Unlike traditional schemes that rely on optical cavities or atomic references, we stabilize the laser frequency via a closed-loop feedback system referenced to a wavelength meter. This configuration effectively suppresses long-term frequency drifts, achieving frequency stability to the wavelength meter’s shot-noise-limited resolution. The system enables sub-hundred-kilohertz stability without complex optical components, making it suitable for compact or field-deployable applications. Our results demonstrate that, with proper feedback design, wavelength meter-based locking can offer a practical and scalable solution for precision optical experiments requiring long-term frequency stability. 1 Introduction Laser frequency stabilization is essential for a broad range of applications, including high-resolution spectroscopy [ 1 , 2 , 3 ] , cold atomic and molecular physics [ 4 , 5 ] , quantum information and computing [ 6 , 7 ] , optical interferometry [ 8 , 9 , 10 ] , and optical frequency standards [ 11 , 12 , 13 ] . As experimental demands continue to tighten—particularly in ultracold atom physics and quantum metrology—there is a growing need for stabilization systems that combine sub-megahertz precision, long-term reliability, and operational simplicity. Among the many available stabilization techniques, wavelength meter (WM)-based frequency stabilization has garnered increasing attention for its unique combination of flexibility, compactness, and ease of integration [ 14 , 15 ] . Unlike other typical methods that rely on high-finesse optical cavities or atomic/molecular references, WM-based stabilization provides absolute, broadband frequency readout with minimal hardware complexity [ 16 , 17 ] . This makes it especially attractive for multi-laser setups, field-deployable systems, and experiments requiring agile reconfiguration or compact footprints. Notably, the advantages of WM-based stabilization have become even more pronounced with the advent of modern fiber and solid-state lasers, which routinely exhibit sub-100 kHz linewidths directly out of the box. In such cases, additional high frequency linewidth narrowing is often unnecessary, shifting the technical emphasis toward stable and accurate frequency referencing. This trend reinforces the relevance and practicality of WM-based stabilization as a cost-effective and scalable solution for contemporary precision applications. However, despite its appeal, WM-based stabilization faces inherent limitations in frequency stability, particularly at short time scales and under stringent precision requirements [ 18 , 19 ] . Commercially available systems typically achieve fractional frequency stabilities on the order of 10^{-10} over timescales of several seconds to minutes [ 20 , 21 , 22 ] . Such performance is insufficient for applications such as laser cooling on narrow intercombination lines or the operation of ultrastable lattice clocks, where absolute frequency fluctuations at the few-kilohertz level are often required [ 23 , 24 ] . The primary factors limiting the performance of WM-based frequency stabilization are photon shot-noise and slow thermal drifts. In systems based on Fizeau or Michelson interferometers, the wavelength is determined from the spatial position and contrast of interference fringes recorded by a CCD or CMOS sensor [ 25 ] . Shot-noise introduces statistical fluctuations in the detected signal, resulting in an inherent measurement uncertainty that scales as \delta f\propto\sqrt{N} [ 26 ] , where N is the number of detected photons. This sets a limit on the short-term frequency precision, even in the absence of other technical noises. Additionally, thermal drifts in the interferometer structure—due to thermal expansion of optical components—lead to slow fluctuations in the measured wavelength, representing a dominant source of long-term instability and accuracy in practical implementations. In this work, we demonstrate sub-100mkHz-level laser frequency stabilization using a commercially available high-resolution WM in conjunction with a narrow-linewidth 556 nm fiber laser. We begin by conducting a detailed characterization of the noise landscape in our setup, identifying the CCD shot-noise in the WM as the principal constraint on performance. We then implement a suite of system-level optimizations—tuning the interferometer readout parameters, actively suppressing the temperature fluctuation and electronic noise, including 50 Hz power-line interference. Under optimized conditions, the system achieves a minimum fractional frequency instability of 1.6\times 10^{-12} at an averaging time of 10,000 s. This represents an improvement of over an order of magnitude compared to the best results previously reported using similar WM-based techniques. [ 27 ] . Moreover, the frequency noise spectrum of the stabilized laser remains within a factor of 5 of the WM’s theoretical shot-noise floor across most of the frequency range. These results demonstrate that, with thoughtful noise mitigation and control-loop engineering, WM-based frequency stabilization can closely approach its fundamental noise limit. Our results establish a clear performance benchmark for WM-based stabilization and highlight its potential as a compact, robust, and cost-effective solution for precision-demanding applications in quantum optics, atomic physics, and metrology. 2 Experimental setup Figure 1: (a) Schematic of the WM-based laser frequency stabilization setup. The 556 nm laser is stabilized using a WM, PC-controlled digital-to-analog converter (DAC), and PID controller with an isolated low-noise PZT driver. The WM provides real-time frequency readout, converted by the DAC to an analog signal for PID feedback. The isolation driver ensures electrical isolation, noise filtering, and voltage matching for the PZT. (b) Frequency noise PSD of the free-running 556 nm fiber laser. For Fourier frequencies above 3 Hz, the laser’s intrinsic noise is significantly lower than the shot-noise-limited floor of the WM. (c) Typical interference fringes recorded by the WM. Inset: close-up of a single fringe peak. Error bars show intensity fluctuations from 10,000 readings. Figure 2: (a) Frequency noise PSD of the WM measured at different CCD exposure times t_{\mathrm{exp}} using the 556 nm fiber laser. (b) Extracted noise floor A_{0} (black) and measured fringe intensity fluctuations (red) as a function of exposure time t_{\mathrm{exp}} . A_{0} increases linearly with t_{\mathrm{exp}} , and the intensity fluctuations follow a \sqrt{t_{\mathrm{exp}}} dependence (solid lines), consistent with shot-noise-limited behavior. Error bars indicate standard deviation across 10,000 frames (red) and fitting uncertainty (black). The WM-based laser frequency stabilization scheme is illustrated in Fig. 1 (a). A 556 nm fiber laser (Model FL-SF-556-0.3-CW, Preciselaser) serves as the light source. This ytterbium-doped fiber laser, combined with single-pass frequency doubling, delivers high output power while maintaining a narrow linewidth of about 31 kHz. This linewidth is estimated by integrating the frequency noise power spectral density (PSD) over a 1 second window, as shown in Fig. 1 (b). Due to the laser’s built-in feedback loop, high-frequency noise components are effectively suppressed, leaving low-frequency fluctuations as the dominant contribution to the frequency noise. This noise profile makes the laser particularly well-suited for WM-based laser frequency stabilization. A commercial WM (Model WS8-2, HighFinesse GmbH) is used as the laser frequency reference. It employs multiple solid-state Fizeau interferometers (FZIs) to perform precise wavelength measurements. The resulting interference fringes are recorded by CCD arrays, generating characteristic fringe patterns [Fig. 1 (c)]. The fringe intensity along a transverse axis x is described by I(x)=I_{0}(x)\left[1+\cos\left(2\pi x\frac{2\alpha}{\lambda}+\frac{2e}{\lambda}\right)\right]. (1) Here, \alpha denotes the wedge angle between the reflecting surfaces of the FZI, and e represents the separation thickness at the reference position x=0 [ 28 ] . Both \alpha and e are

Read the complete text