Photomultiplier Requirements and Pre-Calibration for the SABRE South Liquid Scintillator Veto

M. J. Zurowski · 2025

Read Photomultiplier Requirements and Pre-Calibration for the SABRE South Liquid Scintillator Veto by M. J. Zurowski (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2505-10353.txt.

Introduction

Milligan and co-authors set light sensor needs for a dark matter veto in a 2025 paper. SABRE South hunts dark matter deep underground in Australia. A liquid scintillator veto flags stray radiation around the main detector. Its photomultiplier tubes must survive oil contact and keep thresholds low.

The team characterize the chosen Hamamatsu tubes before use. Bench tests measure gain, noise, and response for the veto's needs. Results feed design choices for low-threshold running. A small prototype detector then tests how well pulse shapes separate signal-like events. The study readies the veto to test a long-standing claimed dark matter signal.

Catalog record

CREATORM. J. Zurowski
YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE61 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2505-10353

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Photomultiplier Requirements and Pre-Calibration for the SABRE South Liquid Scintillator Veto M. J. Zurowski Abstract We present a study of the oil-proof base Hamamatsu R5912 photomultiplier tubes that will be used in the SABRE South linear-alkylbenzene liquid scintillator veto. SABRE South is a dark matter direct detection experiment at the Stawell Underground Physics Laboratory, aiming to test the DAMA/LIBRA dark matter annual modulation signal. We discuss the requirements of the liquid scintillator system and its photomultipliers, outline the methods and analysis used for the characterisation measurements, and results from initial tests. We discuss the impact of these measurements on the performance of the active veto system and explore analysis methods to allow for low threshold operation. Finally, we include results from a small scale liquid scintillator detector prototype used to assess the future performance of pulse shape discrimination in the liquid scintillator veto, and how well accommodated it is by the R5912 PMTs. 1 Introduction This paper presents the characterisation of the oil-proof base Hamamatsu Photonics R5912 photomultiplier tubes (PMTs) for the veto detector of the SABRE South dark matter experiment, including testing in a liquid scintillator prototype detector and the development of analysis methods for background rejection and particle identification. The SABRE experiment aims to provide a test of the long-standing dark matter signal claim by the DAMA experiment [ 1 ] . SABRE consists of two detectors — SABRE North at Laboratori Nazionali del Gran Sasso (LNGS), Italy and SABRE South at the Stawell Underground Physics Laboratory (SUPL) [ 2 ] , Australia [ 3 ] (the first underground laboratory in the Southern Hemisphere). The use of detectors located in two separate hemispheres will allow for the exclusion of seasonal systematic effects. At the heart of SABRE South is an array of high-purity NaI(Tl) crystals coupled to pairs of 76 mm diameter R11065 PMTs (Hamamatsu). These crystal detector modules are mounted in the centre of a stainless steel vessel which contains 12 kL of linear-alkylbenzene liquid scintillator and is instrumented with a minimum of eighteen 204 mm diameter R5912 PMTs from Hamamatsu. This is the largest liquid scintillator veto amongst similar NaI(Tl) experiments. A total of 32 PMTs could be installed in the veto, given we have recently acquired 16 R5912 PMTs from the decommissioned Daya Bay outer detector [ 4 ] . The liquid scintillator veto, capable of tagging external and intrinsic background processes, is one of the chief improvements of the SABRE South detector over other NaI(Tl) dark matter searches [ 5 , 6 ] . The main role of this liquid scintillator veto is to tag radioactive decays within the crystals, but will also act as passive shielding for external background. In addition, a top layer of eight plastic scintillator panels located above the vessel serves as a muon veto. The linear-alkylbenzene is nominally doped with 3.5 g/L of the fluorophore 2,5-Diphenyloxazole (PPO) and 15 mg/L of Bis-MSB to mitigate the self-absorption properties of LAB and to maximise the total light yield [ 7 ] . The LAB emission spectrum peaks at 280 nm [ 8 ] , through subsequent absorption and emission by first PPO and then Bis-MSB, the emission wavelength is shifted to a spectrum centred around 422 nm, which is better matched to the maximum PMT quantum efficiency at 390 nm. Light collection efficiency is improved by lining the internal vessel walls with sheets of reflective polyester (PET) film, or “Lumirror". The locations of the PMTs in the veto vessel, and their incident angles were chosen so that they point toward the centres of the crystal detectors to maximise detection efficiency. Two calibration systems are installed in the sub-detector: a radioactive source based calibration system and an optical calibration system that uses a picosecond pulsed laser source. The radioactive calibration system is used for energy scale calibration while the optical calibration system serves to monitor the performance of the PMTs over time. Simulation studies have shown that effective background reduction for processes that occur in the energy region-of-interest (e.g. intrinsic 40 K decays) is achieved with a veto detector energy threshold of a few hundred keV [ 9 ] , and it may be possible to push the threshold as low as 50 keV [ 10 , 9 , 2 ] . However, in the case of 32 PMTs, a threshold as low as 20 keV becomes increasingly achievable. This lower threshold would open up the possibility of using the liquid scintillator system to detect unusual dark matter signals such as those described in Refs. [ 11 , 12 ] , as well as supernova neutrinos and participation in a supernova early warning system (SNEWS) [ 13 ] . To achieve a low energy threshold throughout the volume of the detector the photon detection efficiency must be maximised given a light yield of \mathcal{O}(10) PE/keV (photoelectrons/keV). Simultaneously, dead-time due to external background must be minimised, and the signal-to-noise ratio must be well understood. The PMTs used in the liquid scintillator veto detector must be calibrated prior to installation. Each PMT’s properties have important implications for how efficiently background can be vetoed and how accurately they can be characterised. The following characterisation measurements have been performed and will be described in detail in this paper: dark rate as a function of temperature, single photon-electron response in terms of charge and timing, quantum efficiency, and the dynamic range of the PMT. In addition to this, spontaneous light emission in the oil-proof base of the PMT is studied. This is a known noise effect reported by other experiments using similar potted bases [ 14 ] . The liquid scintillator veto sub-detector can also be used to characterise background contributions. A key aspect of background reconstruction is particle identification (PID) based on digitised waveform information. To develop and understand the viability of new PID methods that could be applied to the full scale detector, a small prototype using the same liquid scintillator and PMT model is studied. Machine learning methods for gamma-ray/neutron discrimination are presented. This technique shows promise and could be adapted to the final detector to great effect. 2 Veto Sub-detector Requirements and Simulation 2.1 Simulation and Geometry Simulations based on Geant4 [ 15 ] are used to define the requirements of the SABRE South PMTs and the pre-calibration process. A render of the geometry is shown in Fig. 1 . The coordinate system is defined with the origin being the centre of the crystal in the middle of the array, and the Z axis is the vertical direction. The R5912 PMTs are modelled as a 2 mm thick ellipsoid window made of borosilicate glass, with a 10 \mu m ceramic inner surface to serve as a photocathode. Figure 1 : Simulated version of the SABRE South detector. The coordinates labelled correspond to the internal coordinate system of the Geant4 setup (described in text). To produce simulations of optical photons within the veto sub-detector, we need to assume the light yield (LY) of the liquid scintillator. The liquid scintillator is given a LY of 12 PE/keV (on par with measurements of other LAB based scintllators [ 16 , 17 ] ), with a final emission probability equal to that of the Bis-MSB emission. The

Read the complete text