Further Characterisation of Digital Pixel Test Structures Implemented in a 65 nm CMOS Process

Gianluca Aglieri Rinella, Nicole Apadula, Anton Andronic, Matias Antonelli, Mauro Aresti, Roberto Baccomi, Pascal Becht, Stefania Beole, Marcello Borri, Justus Braach, Matthew Daniel Buckland, Eric Buschmann, Paolo Camerini, Francesca Carnesecchi, Leonardo Cecconi, Edoardo Charbon, Giacomo Contin, D · 2025

Read Further Characterisation of Digital Pixel Test Structures Implemented in a 65 nm CMOS Process by Gianluca Aglieri Rinella, Nicole Apadula, Anton Andronic, Matias Antonelli, Mauro Aresti, Roberto Baccomi, Pascal Becht, Stefania Beole, Marcello Borri, Justus Braach, Matthew Daniel Buckland, Eric Buschmann, Paolo Camerini, Francesca Carnesecchi, Leonardo Cecconi, Edoardo Charbon, Giacomo Contin, D (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2505-05867.txt.

Introduction

Future particle detectors need sensors that are light, fast, and stingy with power. A large international collaboration reports new test results in 2025 for tiny digital pixel chips. The chips were built in a 65 nm CMOS process, the same broad family of methods used to make computer chips.

The chips are test versions for the ALICE ITS3 detector, which will bend wafer-scale sensors into curved layers around the collision point. The team measured how the test structures behave, building on earlier rounds of tests. Their results feed the design of a detector layer that aims to use very little material and only a small amount of power in its active area, as the project requires.

Catalog record

CREATORGianluca Aglieri Rinella, Nicole Apadula, Anton Andronic, Matias Antonelli, Mauro Aresti, Roberto Baccomi, Pascal Becht, Stefania Beole, Marcello Borri, Justus Braach, Matthew Daniel Buckland, Eric Buschmann, Paolo Camerini, Francesca Carnesecchi, Leonardo Cecconi, Edoardo Charbon, Giacomo Contin, D
YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE47 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2505-05867

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Further Characterisation of Digital Pixel Test Structures Implemented in a 65 nm CMOS Process Gianluca Aglieri Rinella, Nicole Apadula, Anton Andronic, Matias Antonelli, Mauro Aresti, Roberto Baccomi, Pascal Becht, Stefania Beole, Marcello Borri, Justus Braach, Matthew Daniel Buckland, Eric Buschmann, Paolo Camerini, Francesca Carnesecchi, Leonardo Cecconi, Edoardo Charbon, Giacomo Contin, Dominik Dannheim, Joao de Melo, Wenjing Deng, Antonello di Mauro, Jan Hasenbichler, Hartmut Hillemanns, Geun Hee Hong, Artem Isakov, Hangil Jang, Antoine Junique, Minjung Kim, Alex Kluge, Artem Kotliarov, Filip Křížek, Lukas Lautner, Sanghoon Lim, Magnus Mager, Davide Marras, Paolo Martinengo, Silvia Masciocchi, Marius Wilm Menzel, Magdalena Munker, Francesco Piro, Alexandre Rachevski, Karoliina Rebane, Felix Reidt, Roberto Russo, Isabella Sanna, Valerio Sarritzu, Serhiy Senyukov, Walter Snoeys, Jory Sonneveld, Miljenko Šuljić, Peter Svihra, Nicolas Tiltmann, Vittorio Di Trapani, Gianluca Usai, Jacob Bastiaan Van Beelen, Mirella Dimitrova Vassilev, Caterina Vernieri, Anna Villani Abstract The next generation of MAPS for future tracking detectors will have to meet stringent requirements placed on them. One such detector is the ALICE ITS3 that aims to be very light at 0.07 % 0.07\text{\,}\mathrm{\%} X/X 0 per layer and have a low power consumption in the active area of 40 mW cm − 1 40\text{\,}\mathrm{mW}\text{\,}{\mathrm{cm}}^{-1} by implementing wafer-scale MAPS bent into cylindrical half layers. To address these challenging requirements, the ALICE ITS3 project, in conjunction with the CERN EP R&D on monolithic pixel sensors, proposed the Tower Partners Semiconductor Co. 65 nm 65\text{\,}\mathrm{nm} CMOS process as the starting point for the sensor. After the initial results confirmed the detection efficiency and radiation hardness, the choice of the technology was solidified by demonstrating the feasibility of operating MAPS in low-power consumption regimes, < 50 mW cm − 1 <$50\text{\,}\mathrm{mW}\text{\,}{\mathrm{cm}}^{-1}$ , while maintaining high-quality performance. This was shown through a detailed characterisation of the Digital Pixel Test Structure (DPTS) prototype exposed to X-rays and ionising beams, and the results are presented in this article. Additionally, the sensor was further investigated through studies of the fake-hit rate, the linearity of the front-end in the range 1.7 – 28 keV 1.728\text{\,}\mathrm{k}\mathrm{e}\mathrm{V} , the performance after ionising irradiation, and the detection efficiency of inclined tracks in the range 0 – 45 ° 045\text{\,}\mathrm{\SIUnitSymbolDegree} . Journal: Nucl. Instrum. Methods Phys. Res. A 1 Introduction Monolithic Active Pixel Sensors (MAPS) incorporate the charge-sensitive volume and the read-out circuitry in one piece of silicon and can be fabricated in standard CMOS processes. This allows for a sensor that has promising characteristics for tracking detectors, such as low capacitance, low mass and low power consumption. MAPS were intensively developed and used over the last decade [ 1 ] . MAPS have demonstrated their suitability for operation in high-energy physics experiment vertex and tracking detectors [ 2 ] . The most recent implementation of a large-area MAPS detector was the Inner Tracking System 2 (ITS2) for the ALICE experiment at CERN [ 3 , 4 ] . The ITS2 uses the ALPIDE chip [ 5 , 6 ] , which was fabricated in the TowerJazz 180\text{\,}\mathrm{nm} CMOS process and showed excellent performance in terms of detection efficiency ( \gg 99\text{\,}\mathrm{\%} ) and spatial resolution (about 5\text{\,}\mathrm{\SIUnitSymbolMicro m} ). The ITS2 will undergo an upgrade called the ITS3, where the three innermost tracking layers will be replaced during the LHC Long Shutdown 3 (2026–2028) [ 7 ] . The ITS3 employs wafer-scale MAPSs with a length of 260\text{\,}\mathrm{mm} that are thinned to \leq$50\text{\,}\mathrm{\SIUnitSymbolMicro m}$ to reduce the material in the detector. These sensors are required to have power consumption below 40\text{\,}\mathrm{mW}\text{\,}{\mathrm{cm}}^{-1} in the active area so that operation at temperatures achievable by air cooling O($+25\text{\,}\mathrm{\SIUnitSymbolCelsius}$) is possible [ 8 ] . Due to the challenging requirements imposed on the next generation of MAPS detectors, the Tower Partners Semiconductor Co. (TPSCo) 65\text{\,}\mathrm{nm} CMOS imaging process [ 9 ] was chosen as the starting point for sensor development. The first submission in the 65\text{\,}\mathrm{nm} CMOS process, in conjunction with the CERN EP R&D on monolithic pixel sensors [ 10 ] , was called Multi-Layer Reticle 1 (MLR1). It contained many different test structures to fully explore the feasibility of using the CMOS process for use in future detectors [ 11 ] . With the first set of results from the MLR1 demonstrating the detection efficiency and radiation hardness of the 65\text{\,}\mathrm{nm} technology [ 12 , 13 ] , further investigations into the performance of the technology were carried out. Therefore, a MAPS prototype called the Digital Pixel Test Structure (DPTS) was characterised by fluorescence X-rays and ionising particles from a beam, the results of which are presented in this paper. Since one of the crucial requirements for the next generation of MAPS is reduced power usage, a particular focus was placed on the operation and performance of the sensor in low-power settings. Given that the active region of the final ITS3 stitched sensor will be a complex design with many components, and the DPTS is a simpler design, a comparison of the active region power consumption is not appropriate. Instead, because the two chip designs have similar pixel architectures, the pixel matrix power consumption will be used for a more representative comparison. The target for the pixel matrix power consumption of the ITS3 sensor is 15\text{\,}{\mathrm{m}\mathrm{W}\mathrm{/}\mathrm{c}\mathrm{m}^{2}} for a pixel pitch of 20.8\times 22.8 \mathrm{\SIUnitSymbolMicro m} [ 8 ] . In addition, the performance after ionising irradiation, a study of the Fake-Hit Rate (FHR), the evaluation of the linearity of the front-end, and the response to inclined tracks were also examined. 2 The DPTS chip The DPTS sensor measures 1.5\text{\times}1.5\text{\,}\mathrm{mm} , features a 32\text{\times}32 pixel matrix with a pitch of 15\text{\,}\mathrm{\SIUnitSymbolMicro m} and contains full-CMOS circuitry [ 12 , 14 ] . This allows a digital front-end in each pixel, including an amplifier, shaper, and discriminator, as detailed in [ 12 ] . Furthermore, a test circuitry that injects an externally controlled test charge is also present in the pixel. The sensor can be configured by the shift register located on the periphery, allowing pixel masking and pixel selection for pulsing. The sensor is controlled by external reference currents and voltages and is read out via a Current-Mode Logic (CML) output [ 15 ] . All pixels are read out simultaneously via a differential digital output that encodes the pixel position and Time-over-Threshold (ToT). The steady-state front-end power consumption of a pixel is given by the currents I_{bias} , I_{biasn} , I_{db} , and I_{reset} multiplied by the supply voltage ( +1.2\text{\,}\mathrm{V} ). Since the reset current is orders of magnitude lower than the other currents ( \mathrm{pA} compared to \mathrm{n}\mathrm{A} ) and the I_{db} current in the discriminator branch flows only while the discriminator is active, the total current of the pixel is given by the main branch, I_{bias} . Thus, the lowest possible power consumption is 12\text{\,}\mathrm{nW} per pixel due to 10\text{\,}\mathrm{nA} being the lowest operational I_{bias} setting. 3 Laboratory measurements 3.1 Data acquisition setup The biases and control signals are supplied to the DPTS chip via a custom-made setup, allowing the control of the in-pixel front-end. The chip biases are set to the so-called “nominal” values defined by the design operating point, as described in Ref. [ 12 ] , unless otherwise stated or varied in the measurement. For

Read the complete text