Leveraging high fluence and low pressure for pulsed laser deposition of high-mobility γ \mathrm{\gamma} -Al 2 O 3 /SrTiO 3 heterostructure growth

Thor Hvid-Olsen, Christina Hoegfeldt, Amit Chanda, Alessandro Palliotto, Anshu Gupta, Dae-Sung Park, Thomas Sand Jespersen, Felix Trier · 2025

Read Leveraging high fluence and low pressure for pulsed laser deposition of high-mobility γ \mathrm{\gamma} -Al 2 O 3 /SrTiO 3 heterostructure growth by Thor Hvid-Olsen, Christina Hoegfeldt, Amit Chanda, Alessandro Palliotto, Anshu Gupta, Dae-Sung Park, Thomas Sand Jespersen, Felix Trier (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2505-03685.txt.

Introduction

A thin oxide pair can host a sheet of fast electrons at its seam, a prize for future devices. Thor Hvid-Olsen and co-authors share a growth recipe for one such pair in a 2025 paper. They blast a target with laser pulses to lay the film on a strontium titanate base.

Across forty samples, two settings proved key: strong laser shots and very low chamber pressure. A top sample showed electron speed among the best for this seam at low heat. The single-element top layer lets growers use strong shots without spoiling the mix. Room-heat sheet readings give a quick sign of a good run. The recipe can guide labs that chase faster oxide devices.

Catalog record

CREATORThor Hvid-Olsen, Christina Hoegfeldt, Amit Chanda, Alessandro Palliotto, Anshu Gupta, Dae-Sung Park, Thomas Sand Jespersen, Felix Trier
YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE27 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2505-03685

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Leveraging high fluence and low pressure for pulsed laser deposition of high-mobility γ \mathrm{\gamma} -Al 2 O 3 /SrTiO 3 heterostructure growth Thor Hvid-Olsen, Christina Hoegfeldt, Amit Chanda, Alessandro Palliotto, Anshu Gupta, Dae-Sung Park, Thomas Sand Jespersen, Felix Trier Abstract High-mobility oxide heterostructures could be applied for high-frequency devices, transparent conductors, and spin-orbit logic devices. SrTiO 3 is one of the most studied oxide substrate materials for heterostructures. To date, the highest SrTiO 3 -based charge carrier mobility at 2 K was measured in the interfacial 2-dimensional electron gas (2DEG) of γ \mathrm{\gamma} -Al 2 O 3 /SrTiO 3 . The formation mechanism and origin of the high electron mobility are not yet fully understood. This investigation presents a successful growth protocol to synthesise high-mobility γ \mathrm{\gamma} -Al 2 O 3 /SrTiO 3 interfaces, and a description of the underlying growth optimisation. Furthermore, indicative features of high-mobility γ \mathrm{\gamma} -Al 2 O 3 /SrTiO 3 , including the room-temperature sheet resistance, are presented. Signs of epitaxial and crystalline growth are found in a high-mobility sample ( μ 10 ​ K = 1.6 × 10 4 \mu^{\mathrm{10K}}=1.6\times 10^{4} cm 2 /Vs). Outlining the growth mechanisms and comparing 40 samples, indicates that low pressure ( P ≈ 1 × 10 − 6 P\approx 1\times 10^{-6} mbar) is essential for high-mobility γ \mathrm{\gamma} -Al 2 O 3 /SrTiO 3 interfaces. γ \mathrm{\gamma} -Al 2 O 3 having single-element cations allows higher laser fluences during growth, compared to thin films with multi-element cations such as LaAlO 3 , without causing stoichiometric imbalances. I Introduction For two decades, oxide-based two-dimensional electron gasses (2DEGs) have been intensively studied [ 23 ] for their diverse features, such as superconductivity, [ 25 ] ferromagnetism, [ 1 ] glassy dynamics, [ 19 ] , tunable Rashba spin-orbit coupling, [ 3 ] high-mobility transport, [ 4 , 8 ] extreme magnetoresistance, [ 9 ] and spin-charge interconversion. [ 30 , 22 , 31 ] In recent years, several steps have been taken toward implementing such oxide interfaces. This includes the generation and detection of spin-currents in ferromagnet-free oxide nanodevices [ 30 ] and fabrication of free-standing oxide interface membranes, [ 28 , 11 , 17 ] , paving the way for cointegrating oxide and silicon electronics and spintronics in everyday devices. While most studies focus on the LaAlO 3 /SrTiO 3 interface, the highest charge carrier mobility, \mu=140\,000 \mathrm{cm^{2}/Vs} at 2 K, is recorded for \mathrm{\gamma} -Al 2 O 3 /SrTiO 3 , [ 4 ] presumably due to a band-inversion that renders the d xz/yz band dominant in electronic transport. [ 2 , 7 ] This attractive property allows for mean free path dependent quantum and spintronics measurements, [ 24 ] with potential in applications including high-frequency devices, [ 29 ] transparent conductors, [ 29 ] and spin–orbit logic devices. [ 20 ] At room temperature, longitudinal optical (LO) phonons and electron-electron scattering dominate the carrier mobility in SrTiO 3 . [ 8 , 13 , 21 ] These two scattering phenomena dominate at different carrier density ranges. One attempt to counteract the LO phonon scattering, leveraged the non-polar, low effective electron mass, oxide BaSnO 3 , instead of SrTiO 3 , to reach room temperature mobilities on 60 \mathrm{cm^{2}/Vs} , an order of magnitude higher than SrTiO 3 -based 2DEGs. [ 12 ] The different mobilities of the two materials are attributed to the orbitals near the Fermi Energy. In SrTiO 3 , these orbitals are the d -band orbitals of Ti, with degenerate t 2g symmetry, while it is the isotropic s -band orbitals in BaSnO 3 . From the less dispersive d -band orbitals, the carriers have a higher rate of inter-orbital scattering in SrTiO 3 compared to s -band orbital BaSnO 3 . [ 12 ] Figure 1: Pressure-control for increased reproducibility and crystal structure. a) Schematic of the \mathrm{\gamma} -Al 2 O 3 /SrTiO 3 crystal structure grown with the PLD setup illustrated in b). c-f) Examples of temperature (brown) and pressure (purple) profiles on Protocols 1-4, respectively. At low temperatures, phonon-scattering vanishes, and the main mobility-reducing mechanism in SrTiO 3 2DEGs is impurity scattering. This complicates achieving high mobility, as one of the major mechanisms forming the 2DEGs uses oxygen vacancies. Oxygen vacancies act as both dopants and scattering sites, motivating several studies into the spatial separation of oxygen vacancies and the 2DEG that arises from them. [ 33 , 7 , 5 , 14 ] Here, we present an optimisation of the pulsed laser deposition (PLD) parameters of \mathrm{\gamma} -Al 2 O 3 grown on SrTiO 3 towards forming a high-mobility 2DEG. First, the deposition chamber used in growth, along with four different protocols is presented. Subsequently, relations between low-temperature mobility and residual resistance ratio ( RRR ) and room-temperature sheet resistance ( R_{S}^{RT} ), respectively, are analysed. Then the interface structure of a high-mobility sample is addressed, including epitaxial strain. We then discuss the mechanisms responsible for the high-mobility interfaces throughout the growth process, from as-received substrate SrTiO 3 to high-mobility \mathrm{\gamma} -Al 2 O 3 /SrTiO 3 (001) 2DEG. Based on this discussion, we compare the growth protocols and highlight indications of a strong pressure-dependence of the 2DEG formation. II Experiment Commercial SrTiO 3 (100) substrates [ 18 ] were cleaned by ultrasonication in acetone (480 s), isopropanol (IPA,480 s), and acetone:IPA 50:50 (480 s), then annealed in a 1 bar O 2 atmosphere with a 60 min dwell time at 1000 ∘ C and an up/down ramp rate of 100 ∘ C/h ( \approx 25 h in total with passive cooling). Before \mathrm{\gamma} -Al 2 O 3 deposition, the substrates underwent a second round of ultrasonication in acetone (480 s), IPA (480 s), and acetone:IPA 50:50 (480 s), respectively. The depositions, carried out by PLD, used a single-crystalline \alpha -Al 2 O 3 target. The ablated plasma species forms the \mathrm{\gamma} -Al 2 O 3 structure on SrTiO 3 , as displayed in Fig. 1 a). A 248 nm KrF excimer laser with a repetition rate of 1 Hz was used. We find that the detailed configuration of the growth reactor plays an important role in the optimisation process. The PLD chamber, illustrated in Fig. 1 b), is directly connected to three manually controlled valves. One of the valves, V1, is connected to a mass flow controller for oxygen injection, while two other valves, V2 and V3, connect the chamber to a turbomolecular pump. This pump is further connected to a backing pump through another manual valve (not shown). V2 and V3 controlled the specific pressure when working below 10 -4 mbar. V2 is a manual gate valve controlling the range of pressure, while V3 is an angle valve, allowing for fine-tuning of the pressure. V1 was open during O 2 flushing and automatised proportional–integral–derivative (PID) pressure control. The thermocouple, measuring the sample temperature, resides in the heater centre, and the substrate-target distance was 4.5 \pm 0.1 cm. Table 1: Overview of growth parameters. Parameters Abbreviaion Protocol 1 Protocol 2 Protocol 3 Protocol 4 Flushing Pressure (mbar) P_{\mathrm{flush}} 7 \times 10 -2 NA 7 \times 10 -2 7 \times 10 -2 Deposition pressure (mbar) P_{\mathrm{dep}} 1-2 \times 10 -6

Read the complete text