AC-LGADs Fermilab Front-End Electronics Characterization Journal: Nuclear Instruments A
René Ríos, Esteban Felipe Molina Cardenas, Cristian Peña, Orlando Soto, William Brooks, Artur Apresyan, Sergey Los, Claudio San Martín · 2025
Read AC-LGADs Fermilab Front-End Electronics Characterization Journal: Nuclear Instruments A by René Ríos, Esteban Felipe Molina Cardenas, Cristian Peña, Orlando Soto, William Brooks, Artur Apresyan, Sergey Los, Claudio San Martín (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2504-08932.txt.
Introduction
Ríos and co-authors describe in 2025 tests of the electronics that read out a fast silicon sensor at a Fermilab beam site. The sensors time charged particles with fine precision, which suits tracking work. The team wanted to know how much the readout board itself adds to, or takes from, that timing skill.
They built a rig that feeds in pulses of varied size and read what the board sent out. The board's own timing error came in under two trillionths of a second. Good readout design, they show, is a real part of why the full system times particles so well, not a minor detail.
Catalog record
| CREATOR | René Ríos, Esteban Felipe Molina Cardenas, Cristian Peña, Orlando Soto, William Brooks, Artur Apresyan, Sergey Los, Claudio San Martín |
|---|---|
| YEAR | 2025 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 19 KB |
| VERSION | 1.0 |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2504-08932
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
AC-LGADs Fermilab Front-End Electronics Characterization Journal: Nuclear Instruments A René Ríos, Esteban Felipe Molina Cardenas, Cristian Peña, Orlando Soto, William Brooks, Artur Apresyan, Sergey Los, Claudio San Martín Abstract We characterized the front-end electronics used to process high-frequency signals from low-gain avalanche diodes (LGADs) at the Fermilab Test Beam Facility. LGADs are silicon detectors employed for charged particle tracking, offering exceptional spatial and temporal resolution. The purpose of this characterization was to understand how the signal resolution is influenced by the front-end electronics. To achieve this, we developed a setup capable of generating input signals with varying amplitudes. The output results demonstrated that signal processing by the front-end electronics plays a crucial role in enhancing time resolution. We showed that the time resolution achieved by the FEE board is better than 2 p s 2\>ps . PACS 0000 , 1111 MSC 0000 , 1111 1 Introduction The luminosity upgrade of the LHC brings new challenges: up to hundreds of simultaneous collisions per bunch crossing are expected with this upgrade [ 1 , 2 , 3 ] ; therefore, it is imperative to distinguish these events from each other to ensure a good quality particle identification (PID) and vertex reconstruction. One of the alternatives to take over these challenges is the AC-coupled low-gain avalanche diode (AC-LGAD), a silicon-based device that provide an excellent reconstruction of spatial and time information [ 4 , 5 , 6 ] . Recent studies [ 7 ] estimate a spacial and time resolution in the order of 6-10 micrometers and 30 nanoseconds respectively. In order to extract the performance limits of the AC-LGAD, a specially design front end electronic (FEE) must be used. A 16-channel LGAD Test board (Fig. 1 ) was used as FEE to amplify and read the signals acquired by the AC-LGADs. This board was utilized successfully in the 2021 [ 7 ] and 2022 [ 8 ] AC-LGADs test beam campaigns at the Fermilab Test Beam Facility. Figure 1: Board with the designed charge injector in place of an AC-LGAD. The main objective of this research is the characterization of the Fermilab FEE Board, which acts as the Device Under Test (DUT), starting from detailing its electronic schematic, the experimental setup and equipment utilized, the features of the signals used to characterize the DUT, and the results in terms of frequency response, gain, noise RMS, signal-to-noise ratio (SNR), and time resolution (jitter). 2 AC-LGADs Fermilab Front-End Electronics The DUT has 16 dedicated input channels for each strip or pad of the corresponding AC-LGAD device. Each channel consists of a two-stage amplifier based on the Minicircuits Gali S66+ surface mount monolithic amplifier, which provides amplification in the DC to 3\>GHz frequency range. The amplifier is internally matched to 50\>\Omega , which requires that the traces of the board are designed with a 50\>\Omega impedance. The schematic of a single channel is shown in Fig. 2 . In this particular configuration, the amplifiers used a 25\>\Omega input impedance and a bandwidth of 1\>GHz . The amplifier chain of each readout channel has a uniform gain with an approximate 10\% variation from channel to channel [ 9 ] . Figure 2: Single channel equivalent schematic. At 2\>GHz , the expected gain for each amplifier stage is about 18.2\>dB . The manufacturer specifies [ 10 ] the typical output power at 1\>dB compression is 3.3\>dBm , at 2\>GHz . This output, at 50\>\Omega , is equivalent to \sim 327\>mV . Due to having two stages, the gain at 2\>GHz is a factor of \sim 66 , hence a voltage range amplitude in 0\>-\>4.95\>mV ensures a constant gain at that frequency. The total trans-impedance on the DUT, after two stages of amplification, is roughly 4.3\>k\Omega . The gain for LGAD signals is such that each femtocoulomb of input charge results in an additional 5\>mV in signal amplitude (that is, 100\>mV output for a 20fC input) [ 7 ] . 3 Experimental Setup Overview For the characterization process, we set basic conditions regarding the powering of the board and its temperature. We set 6.8\>V in a Keithley 2230-30-1 DC Power Supply to power the DUT. At that voltage, the current required by the DUT was 0.537\>A . The board was kept inside the box (Fig. 3 ) at a temperature of \sim 21.7\>^{\circ}C throughout the tests using a Lauda Alpha RA 8 recirculating chiller. We measured the temperature with a 10K RTD sensor connected directly to the DUT. We used a SiLabs Si5332-6EX-EVB REV 2.0 LVDS low-jitter clock generator (less than 175 fs RMS phase jitter) configured at 84.3\>MHz to produce squared signals of fixed width and amplitude. One of the outputs of the clock generator is connected directly to the first channel of the oscilloscope as a trigger for the experiment. Two other outputs of the clock generator fed a pulse generator, designed by the CALTECH INQNET [ 11 ] team, based in the NB6L295 Dual Channel Programmable Delay Chip . This device takes two input signals and produces two delayed signals which are driven into a MC100LVEP05 Low Voltage Positive Emitter-Couple Logic (LVPECL) AND gate. The differences in the delays can produce nanosecond-width pulses, that would emulate those produced by a Minimum Ionizing Particle (MIP) when hitting an AC-LGAD. Additionally, we used different attenuation levels at the output of the pulse generator to achieve a similar voltage amplitude to those produced by the signals of MIPs and to study the behavior of the SNR. Figure 3: From left to right: clock generator, oscilloscope, power supply, pulse generator, electromagnetic waves shielding box, multimeter for RTD measurement. The signal produced by the pulse generator (see Fig. 4 ) was set at 1\>ns width and 260\>mV amplitude. Figure 4: Output from the pulse generator without any attenuation applied. We manufactured a charge injector (Fig. 1 ) to guide the output signals of the pulse generator into an input channel of the DUT. The injector consisted of an SMA input connector with a 50\>\Omega resistor coupled to ground to match the input impedance of the cables; additionally, a 100\>nF capacitor was connected in series with the input connector to eliminate LVPECL common mode voltage, and at the output of the charge injector, we used a spring-loaded contact connector. We built a Faraday Cage (Fig. 3 ) to isolate the DUT from external electromagnetic noise. We used the oscilloscope LeCroy WaveRunner 610Zi to perform the measurements; the bandwidth of this device is 1\>GHz and it can achieve up to 20\>GS/s . We arranged these devices in different configurations to perform the characterization. 4 Gain and Jitter characterization 4.1 Experimental Setup The experimental setup is shown in Fig. 5 . Clock Pulse Generator Attenuator Charge Injector FEE Board (DUT) Oscilloscope Clock Pulse Figure 5: Experimental setup for amplitude, noise RMS and jitter analysis. 4.2 Overview of The Pulses We used specially-developed software to acquire and convert binary data directly from the oscilloscope to ROOT framework data files [ 12 ] . This software was developed by the FNAL CMS-MTD team, which was successfully utilized in previous works [ 7 , 8 ] . As a reference, Fig. 6 shows 5000 events for the 40\>dB configuration. Figure 6: 5000 events acquired