Modelling Lateral Spread in Wire Flat Rolling

Mozhdeh Erfanian, Carl D. Slater, Edward J. Brambley · 2025

Read Modelling Lateral Spread in Wire Flat Rolling by Mozhdeh Erfanian, Carl D. Slater, Edward J. Brambley (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2504-06300.txt.

Introduction

Mozhdeh Erfanian and co-authors build the first fit-free math model for how wire swells side-wise in flat rolls. Side swell sets the end width of rolled wire, and past calls leaned on tuned dials or heavy mocks. Their 2025 model is drawn straight from the flow laws, with stiff, full-yield stuff and thin-wire shape in hand. No dial is fit to data.

Roll runs on steel wire with palm-width rolls test the calls. Swell calls land true cross a wide span of wire girths and squeeze shares. Run time is mere ticks, so the team sweeps roll and wire spans to map where the model holds. Roll smiths gain a fast check for mocks and a guide for line design.

Catalog record

CREATORMozhdeh Erfanian, Carl D. Slater, Edward J. Brambley
YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE64 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2504-06300

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Modelling Lateral Spread in Wire Flat Rolling Mozhdeh Erfanian, Carl D. Slater, Edward J. Brambley Abstract A mathematical model for wire rolling is developed, focusing on predicting the lateral spread. This provides, for the first time, an analytic model of lateral spread without any fitting parameters. The model is derived directly from the governing equations, assuming a rigid, perfectly plastic material and exploiting the thinness of the wire (in thickness and width) relative to the roller size. Results are compared against experiments performed on stainless steel wire using 100 ​ mm 100\,\mathrm{mm} diameter rolls, demonstrating accurate predictions of lateral spread across a wide range of wire diameters ( 2.96 ​ mm 2.96\,\mathrm{mm} – 7.96 ​ mm 7.96\,\mathrm{mm} ) and reduction ratios (20%–60%), all without the need for fitting parameters. Since the model requires only seconds to compute, the model’s valid range is explored for varying roll diameter, wire diameter, and reduction ratio, and their effects on the resulting lateral spread characterized. The model can serve as a robust tool for validating FE results, guiding process design, and laying the foundation for future improved models. Matlab code to evaluate the model is provided in the supplementary material. Journal: Eur. J. Mech. A/Solids 1 Introduction Applications including sawblades, springs, piston rings, and transformers depend critically on flattened wires ( Utsunomiya et al., 2001 ) . These wires are usually made by a flat rolling technique, where a wire with a circular cross-section is cold rolled between cylindrical rolls — sometimes through several passes — to achieve a particular width and thickness (as illustrated in figure 1 ). Figure 1: A diagram of wire flat rolling process; the wire initially has a circular cross-section with diameter d_{0} and is flattened to a barrel shape cross section with the lateral spread W_{t} and the contact width W_{c} . Adapted from Figure 1 of Carlsson (1998) . Since the wire can both elongate and widen, achieving a final product that closely matches the desired specifications requires an understanding of how the wire deforms, making it essential to predict the lateral spread accurately. In cold rolling of a sheet, deformation in the lateral direction often remains within the elastic range due to the product’s geometry. However, this is not the case when an initial width-to-thickness ratio is less than 6, such as in wide strip or plate, or as low as 1 in round wire ( Chitkara and Johnson, 1966 ) . In such cases, the plastic flow in the roll gap at the start of rolling schedule is inherently three-dimensional, complicating the analysis. For round wire, this complexity is further increased by the transformation of a round cross-section into a rectangular shape with bulged edges during the first pass. Although research exists on the modelling of lateral spread in thick plate rolling ( Chitkara and Johnson, 1966 ; Lahoti and Kobayashi, 1974 ; Oh and Kobayashi, 1975 ; El-Nikhaily, 1979 ; Kennedy, 1987 , e.g.) , wire flat rolling has received less attention. Kazeminezhad et al. ( 2005 ; 2006 ; 2008 ) published a series of papers studying different parameters in wire rolling. Kazeminezhad and Karimi Taheri (2005) developed a relationship for the width of the contact area between the rolls and the wire. Their equation was based on experimental and FE observations of the formation of X-shaped shear bands in the wire cross-section during the rolling process ( Semiatin and Jonas, 1984 ; Pesin et al., 2002 ) , along with the assumption that as the height reduction increases, the shear bands rotate while maintaining a constant length. Kazeminezhad and Karimi Taheri (2006) then applied this equation alongside the slab method, leading to a pressure hill distribution. The study employs the Tresca yield criterion, assuming the longitudinal stress \sigma_{xx} to be the minimum stress, the vertical stress \sigma_{yy} to be the maximum stress, and the compressive stress in the lateral direction, \sigma_{zz} , to lie between them. Although \sigma_{zz} is implicitly included in the yield function, and therefore in calculating the roll pressure, the value of \sigma_{zz} is unknown and must be approximated to find the lateral spread. Kazeminezhad and Karimi Taheri (2005) therefore assumed that \sigma_{zz} takes a value between plane strain and plane stress, written as \alpha\sigma_{yy} , where \alpha is a fitting parameter taking values between 0 and 0.5. Using flow rule equations and setting \sigma_{xx} to be zero at the end of the roll gap, they then wrote \frac{d\varepsilon_{zz}}{-d\varepsilon_{yy}}=\frac{\ln\frac{W_{t}}{d_{0}}}{\ln\frac{d_{0}}{2h_{1}}}=\frac{1-2\alpha}{2-\alpha}, (1) where W_{t} is the lateral spread, d_{0} is the initial diameter, and 2h_{1} is the final height of the wire. The first use of this formulation has been attributed to Hill (1955) for plate rolling and has also been derived by several other authors ( Chitkara and Johnson, 1966 ; Applied Mechanics Group and Sparling, 1961 , e.g.) , who experimentally observed a linear relationship between \ln(W_{t}/W_{0}) and \ln(h_{0}/h_{1}) , where W_{0} and h_{0} are initial half width and half height of the slab, respectively. The factor \alpha and another factor of linearity must then be found empirically from experiments, with a proviso that each resulting equation only gives reasonable lateral spread prediction within the ranges of conditions for which they were empirically determined ( Chitkara and Johnson, 1966 ) . For example, for low and high carbon steel Kazeminezhad and Karimi Taheri (2005) wrote equation ( 1 ) as \frac{W_{t}}{d_{0}}=1.02\left(\frac{d_{0}}{2h_{1}}\right)^{\!0.45}. (2) Among a wide range of empirical formulations suggested for predicting lateral spread ( Chitkara and Johnson, 1966 ) , the one proposed by Kobayashi (1978) is often referred to as being reliable for round wire ( Utsunomiya et al., 2001 ; Kazeminezhad et al., 2008 ; Vallellano et al., 2008 ) . Utsunomiya et al. (2001) and Vallellano et al. (2008) attribute the following equation to Kobayashi (1978) , and we will refer to it here by this name: \frac{W_{t}}{d_{0}}=0.7854\frac{d_{0}}{2h_{1}}\!\left(\!1-15.8\!\left(\!1-\frac{2h_{1}}{d_{0}}\right)^{\!2.25}\!\left(\frac{2R}{d_{0}}\right)^{\!-0.82}\right)\\ +0.1426\left(\frac{2h_{1}}{d_{0}}\right), (3) where R is the roll radius. However, similar to other empirical equations, this equation will be shown to lose accuracy away form the parameters it was initially developed to model. Finite element (FE) analysis has provided valuable insights into wire rolling, similar to other metal-forming processes. Vallellano et al. (2008) performed a 3D numerical analysis using the Abaqus finite element software to study contact stress distributions, residual stresses, and lateral spread. While 3D FE analysis offers highly detailed information, it is computationally expensive, especially when it is used in design iterations where several simulations are required. Although some studies have investigated FE simulations of wire rolling ( Carlsson, 1998 ; Vallellano et al., 2008 ; Hwang et al., 2021 ) , computational cost data are generally not reported. However, to give an indication, a 2D FE simulation of half-of-the-thickness sheet rolling required 15.9 CPU hours for a reliable case (30 elements through the half-thickness) and 0.25 CPU hours for a coarse case (5 elements) ( Flanagan et al., 2025 ) ; since 3D wire-rolling simulations are considerably more complex, they are expected to be significantly more expensive yet. In addition to high computational cost, FE results require validation against a reliable reference. Whether the objective is process design or FE validation, a review of the literature further reveals a notable gap in the availability of

Read the complete text