Flow of a two-dimensional liquid foam: Impact of surfactant type and boundary conditions
Farshad Nazari, Andrei Potanin, Hadi Mohammadigoushki · 2025
Read Flow of a two-dimensional liquid foam: Impact of surfactant type and boundary conditions by Farshad Nazari, Andrei Potanin, Hadi Mohammadigoushki (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2503-20710.txt.
Introduction
Farshad Nazari, Andrei Potanin, and Hadi Mohammadigoushki test, in 2025, how two-dimensional foams flow between plates. The foams were made from two commercial detergents with matched bubble size and water content, and were sheared against smooth and roughened walls in a custom device that allows viewing while measuring.
One foam was stiffer and slower to relax, pointing to a less mobile bubble surface. Under smooth walls, the other foam showed a yield stress while the first did not, despite higher thick-flow stresses. Stress scaling differed with wall type for one foam only. The authors trace the contrasts to detergent chemistry shaping the bubble skin.
Catalog record
| CREATOR | Farshad Nazari, Andrei Potanin, Hadi Mohammadigoushki |
|---|---|
| YEAR | 2025 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 36 KB |
| VERSION | 1.0 |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2503-20710
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
Flow of a two-dimensional liquid foam: Impact of surfactant type and boundary conditions Farshad Nazari, Andrei Potanin, Hadi Mohammadigoushki Abstract In this study, we experimentally investigate the rheological and flow behavior of two-dimensional (2D) monodisperse aqueous foams, sheared between parallel plates using a custom-made rheo-optical apparatus with smooth and roughened walls. The foams were prepared using two commercially available detergents—Foam 1 and Foam 2—while maintaining similar bubble sizes and liquid fractions. The linear viscoelastic results reveal that the Foam 1 consistently exhibits higher elastic and loss moduli than the Foam 2 , regardless of boundary conditions, with roughened walls further enhancing these moduli in both foams. Additionally, the Foam 1 shows a lower viscoelastic relaxation frequency compared to the Foam 2, indicating a less mobile interface for the Foam 1. In the non-linear regime, significant differences were observed. Under smooth boundary conditions, Foam 2 exhibits yield stress behavior, whereas Foam 1 does not, despite having higher viscous stresses. The viscous stress in the Foam 1 scales with the capillary number as τ w ∝ \tau_{w}\propto Ca 0.5 , while for the Foam 2, the scaling depends on the boundary conditions: τ w ∝ \tau_{w}\propto Ca 0.85 for smooth walls and τ w ∝ \tau_{w}\propto Ca 0.65 for roughened walls. These variations in rheological behavior are attributed to differences in surfactant chemistry, leading to different interface mobilities, with the Foam 1 having a less mobile interface compared to the Foam 2. I Introduction Liquid foams consist of a dispersion of gas bubbles in a liquid medium. Despite these two constituents being simple and Newtonian, their combination creates a complex fluid that exhibits strong non-Newtonian rheology. The rheology of the liquid foam depends on multiple factors, including the liquid content, bubble size, bubble size distribution among other factors [ 1 , 2 , 3 , 4 ] . Liquid foams are widely used in a host of applications in oil-gas industry [ 5 , 6 , 7 ] , mining [ 8 ] , cosmetic [ 9 , 10 ] and house-hold products [ 11 ] . The prior published literature on the rheology of liquid foams is expansive and there are numerous excellent reviews on this subject matter, which the readers are referred to [ 1 , 2 , 3 , 4 ] . Liquid foams possess high interfacial energy, making them unstable. Early studies investigated the stability of liquid foams in the quiescent state. In principle, three mechanisms could affect the foam structure; drainage due to gravity, Ostwald ripening due to the pressure gradient between neighboring bubbles, and coalescence due to the rupture of the thin film between neighboring bubbles [ 12 , 13 , 14 , 15 , 16 ] . Under flow, stable liquid foams exhibit a range of complex and rich dynamics [ 2 , 17 ] . The rheology of liquid foam is strongly dependent on the structure of the liquid foam (e.g., bubble size, bubble size distribution, liquid content, etc.) [ 4 ] . Typically, under small deformations (linear viscoelastic regime), liquid foams exhibit a strong solid-like behavior (that is, elasticity) due to the presence of liquid interfaces between bubbles [ 2 ] . Under strong and non-linear deformation rates, liquid foam has been known to exhibit yield stress properties at low shear rates and viscous dissipation at higher rates [ 18 , 19 , 1 ] . These complex rheological features have been reported to be related to local re-arrangement of bubble dynamics [ 1 , 20 , 21 ] . In addition, the rheological response of liquid foams has been shown to be strongly impacted by the type and chemistry of the surfactants used to make liquid foams [ 22 , 23 , 24 , 25 , 26 ] . Typically, the steady-state flow curve of the liquid foam in non-linear viscoelasticity regime can be described by a Herschel-Bulkley fluid model: \tau(\dot{\gamma})=\tau_{y}+\tau_{v}=\tau_{y}+K{\dot{\gamma}}^{n}, (1) where \tau_{y} , K , \dot{\gamma} , and n are yield stress, consistency factor, imposed shear rate and shear thinning index, respectively. Experiments on three-dimensional foam samples have shown that, depending on the surfactant chemistry, bubble interfaces can be mobile or immobile (rigid), which is reflected in n\approx 1/2 for mobile interfaces and n\approx 0.2-0.3 for immobile interfaces when friction between bubble layers is dominant [ 22 ] . This scaling is also affected by the type of boundary conditions used to measure the flow curve of liquid foam [ 22 ] . For example, if there is significant friction between the bubbles and the wall, the scaling changes to n\approx 2/3 for mobile interfaces and to n\approx 1/2 for immobile interfaces [ 27 , 28 , 22 , 25 ] . Three-dimensional liquid foams are opaque, making it difficult to link bubble dynamics to rheology. To address this challenge, researchers have used two-dimensional (2D) liquid foams (bubble monolayers) as a model system to investigate the connection between microstructure and rheology [ 29 , 30 , 31 , 32 , 33 , 34 , 35 , 36 ] . Experiments on the flow of 2D liquid foams have revealed a range of intriguing characteristics, including non-local rheology [ 31 ] , size-based segregation [ 36 , 37 , 38 ] , coalescence [ 35 ] , breakup [ 24 ] , among others. Theoretical studies have suggested a shear shear-thinning index of n\approx 1/2 for 2D polydisperse foams [ 39 , 40 ] . Experiments on 2D foam flow have indicated a shear thinning index of n=0.36-0.4 in a Taylor-Couette cell (flow between two concentric cylinders) without the top wall and n\approx 2/3 in a parallel plate geometry for a 2D foam made of a commercial detergent, which is believed to lead to a mobile interface [ 31 , 32 ] . The latter experiments studied the flow curves of two-dimensional foams within a very low range of shear rates ( \dot{\gamma}<0.1 [1/s]). Consequently, the behavior of 2D liquid foams under higher shear rates remains unexplored. To the best of our knowledge, the impact of surfactant chemistry on non-linear rheology, specifically regarding mobile or immobile interfaces, has not been studied in the flow of 2D liquid foams. Previous studies on the rheology of 2D foam have mainly utilized only one detergent [ 31 , 32 ] . Furthermore, while the impact of surfactant chemistry on the non-linear rheological properties of 3D liquid foams has been extensively studied, its effect on the linear viscoelastic properties of foams has received little attention [ 41 , 42 ] . Krishan et al. showed that for a 3D liquid foam with immobile interfaces, the linear viscoelastic rheology is different from the 3D liquid foam with mobile interface [ 41 ] . In particular, Krishan et al. showed that the viscoelastic relaxation frequency ( f_{c} ; see details below) is typically higher for mobile interfaces than for immobile interfaces [ 41 ] . In addition, while the elastic modulii of the samples with immobile and mobile interfaces were similar, the loss modulus obtained for the 3D liquid foam with immobile interfaces is larger than that obtained for liquid foams with mobile interfaces [ 41 ] . It remains unclear how or whether the type or