Defect Analysis and Built-In-Self-Test for Chiplet Interconnects in Fan-out Wafer-Level Packaging ∗

Partho Bhoumik, Christopher Bailey, and Krishnendu Chakrabarty · 2025

Read Defect Analysis and Built-In-Self-Test for Chiplet Interconnects in Fan-out Wafer-Level Packaging ∗ by Partho Bhoumik, Christopher Bailey, and Krishnendu Chakrabarty (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2503-14784.txt.

Introduction

Partho Bhoumik, Christopher Bailey, and Krishnendu Chakrabarty study faults in chip links in a 2025 paper. The links sit in a fan-out wafer package, a thin form that packs chips close. Heat mismatch, warping, and die shift can misalign parts and break the links.

The authors map common defects to circuit models and test how each fault harms chip work. They then design a built-in self-test that can find stuck and bridging faults. The test also names the fault type and its place. Test results guide trade-offs between fault cover and the cost of adding test parts.

Catalog record

CREATORPartho Bhoumik, Christopher Bailey, and Krishnendu Chakrabarty
YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE30 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2503-14784

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Defect Analysis and Built-In-Self-Test for Chiplet Interconnects in Fan-out Wafer-Level Packaging ∗ Partho Bhoumik, Christopher Bailey, and Krishnendu Chakrabarty Abstract Fan-out wafer-level packaging (FOWLP) addresses the demand for higher interconnect densities by offering reduced form factor, improved signal integrity, and enhanced performance. However, FOWLP faces manufacturing challenges such as coefficient of thermal expansion (CTE) mismatch, warpage, die shift, and post-molding protrusion, causing misalignment and bonding issues during redistribution layer (RDL) buildup. Moreover, the organic nature of the package exposes it to severe thermo-mechanical stresses during fabrication and operation. In order to address these challenges, we propose a comprehensive defect analysis and testing framework for FOWLP interconnects. We use Ansys Q3D to map defects to equivalent electrical circuit models and perform fault simulations to investigate the impacts of these defects on chiplet functionality. Additionally, we present a built-in self-test (BIST) architecture to detect stuck-at and bridging faults while accurately diagnosing the fault type and location. Our simulation results demonstrate the efficacy of the proposed BIST solution and provide critical insights for optimizing design decisions in packages, balancing fault detection and diagnosis with the cost of testability insertion. PubID: pubid: 979-8-3315-2144-8/25/$31.00 ©2025 IEEE 1 I Introduction Advanced packaging has emerged as a pivotal solution for extending the capabilities of integrated circuits (ICs) [ 1 ] . Traditionally, semiconductor devices were designed as large monolithic dies, but as circuits became more complex, industry shifted toward dividing these large dies into smaller, specialized chiplets with higher yields. These chiplets can be interconnected to enable heterogeneous integration, facilitating the development of advanced 2.5D and 3D packages [ 2 , 3 ] . Among the various advanced packaging techniques, fan-out wafer-level packaging (FOWLP) offers several advantages over conventional methods, including enhanced electrical performance, reduced form factor, and higher I/O density [ 4 , 5 , 6 ] . This approach involves using a secondary wafer to position the dies with more separation, thereby allowing the extra area to develop redistribution layers (RDL) that connect the neighboring dies via Cu pillars grown on the die pads. However, coefficient of thermal expansion (CTE) mismatch, warpage, and misalignment during bonding can lead to defects that compromise the integrity of the interconnects [ 7 , 8 , 9 , 10 , 11 , 12 ] . A comprehensive study of these defects is essential to understand the impact of defect size and develop test solutions. Our goal is to tackle the problem of modeling and assessing the impact of various defects within Cu pillars and RDL in a FOWLP package. These defects can originate both during packaging unit processes (such as the RDL build-up processes) and in-service operations due to thermo-mechanical loads [ 13 , 14 ] . Our approach leverages finite element analysis (FEA) to extract the parasitics corresponding to various defect levels, utilizing the Ansys Q3D tool. We show how the impact of these defects can be analyzed by mapping them to their equivalent faulty circuits. Furthermore, built-in self-test (BIST) solutions are essential for advanced packaging [ 15 ] . BIST can be used to detect and locate opens and shorts within interconnects. Once faults are detected and localized, rerouting strategies can be employed to repair the faulty connections. Despite its importance, there has been limited research on package-level BIST. In [ 16 ] , a physically aware test method was proposed for interconnects. This method utilizes an array of pattern generators to apply patterns through the chiplet I/Os. However, it does not define fault models or specify test patterns for these models. It also lacks a fault detection mechanism and a diagnostic scheme for failure analysis. The authors in [ 17 , 18 ] investigated test pattern generation schemes and proposed a test method using automated test equipment and die-wrapper registers to apply the patterns. A total of 16 patterns (4 unique codewords) can test for hard and weak defects within chiplet interconnects. However, scanning test patterns in and out of the tester for thousands of I/Os takes a prohibitive amount of time. An on-chip solution that addresses both post-assembly and in-field fault scenarios is essential for lifecycle monitoring. In this paper, we tackle the challenges associated with detecting and localizing defects within chiplet interconnects. We begin by analyzing these defects, which allows us to identify and quantify their physical and electrical characteristics. This detailed analysis also helps us to understand the relationship between defects and fault models. Based on these fault models, we propose an efficient approach involving only three test patterns to detect, diagnose and localize all interconnect stuck-at-faults (SAFs) and bridging faults. The main contributions of this paper are listed as follows: • We provide a comprehensive characterization of defects inside Cu pillars and RDL. • We demonstrate how to map defects in package components to their equivalent faulty circuits and perform package-level fault simulation using HSPICE. • We present a BIST architecture that detects, locates, and diagnoses stuck-at (SA) and bridging faults. The BIST outcomes can be combined with defect simulation results to identify the extent of deformities in Cu pillars and RDLs. The rest of the paper is organized as follows. Section II provides background on FOWLP and FEA. Section III describes the proposed defect analysis framework and equivalent faulty circuits. In Section IV , the BIST architecture is presented and evaluated, and BIST outcomes are mapped to deformities in package components. Section V concludes the paper. II Background II-A Fan-out Wafer Level Packaging Conventional packaging technologies, such as flip-chip, FOVEROS, EMIB, and CoWoS, rely heavily on substrates or interposers [ 19 ] , which introduce additional layers, cost, and complexity. FOWLP is an alternative approach that encapsulates the entire die within a molding compound, creating a smooth and continuous surface. In a chip-first, face-up FOWLP method, Cu pillars are first grown at the I/O locations on the native semiconductor wafer. After that, the dies are placed on a reconstituted wafer panel using the die pick and place method. During panelization, the dies are covered on both the front and sides with epoxy molding compound (EMC), with the Cu pillars providing the current pathways through the mold. The panel is then processed by building up interconnections between the exposed Cu pillars and the Cu RDL. An epoxy laminate is applied to the backside of the panel to fully encase the die in epoxy; see Fig. 1 . Adaptive Patterning (AP) is used to dynamically scan the position of the Cu bumps and adjust interconnect routing to reduce the impact of die shift [ 20 ] . Fig. 1: Illustration of a fully molded FOWLP structure [ 21 ] . Testability solutions for this promising technology have yet to be studied. [ 21 ] demonstrated a test vehicle approach to assess interconnect continuity using a daisy chain. This approach is limited to test vehicles and does not extend to practical applications. Ansys modeling was carried out to simulate the thermal cycling performance of the test package, focusing on strain energy density distribution in critical solder joints. However, there are many other sources of defects that need to be studied. Comprehensive design for test structures is necessary to detect, diagnose, and repair defects. II-B Finite Element Analysis FEA begins by creating a mesh of

Read the complete text