Capillary jet in a slab of foam
Théophile Gaichies, Bryan Giraud, Emmanuelle Rio, Anniina Salonen, Arnaud Antkowiak · 2025
Read Capillary jet in a slab of foam by Théophile Gaichies, Bryan Giraud, Emmanuelle Rio, Anniina Salonen, Arnaud Antkowiak (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2503-04345.txt.
Introduction
Five authors study in 2025 what a fine liquid jet does when it dives into a thin slab of foam made of the same soap mix. At low speed the jet swells the channels between bubbles. At mid speed, hits on those channels spawn very small new bubbles.
At high speed the jet thins the soap films and can pop bubbles. To pin down each step, the team built a simple foam of three films that meet at one border. Scaling laws from that toy foam matched the full slab well, which gives a clean rule set for jet and foam play.
Catalog record
| CREATOR | Théophile Gaichies, Bryan Giraud, Emmanuelle Rio, Anniina Salonen, Arnaud Antkowiak |
|---|---|
| YEAR | 2025 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 15 KB |
| VERSION | 1.0 |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2503-04345
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
Capillary jet in a slab of foam Preprint: APS/123-QED Théophile Gaichies, Bryan Giraud, Emmanuelle Rio, Anniina Salonen, Arnaud Antkowiak Abstract A capillary jet plunging into a quasi-2D slab of monodisperse foam of the same solution is studied experimentally. We show that the jet can have a drastic impact on the foam. At small speeds it inflates the channels separating the bubbles. At intermediate speeds, impact with channels creates very small bubbles. At higher speeds, the jet thins the foam films, which can result in bubble rupture. We study the mechanisms behind these processes using an elementary foam formed by three soap films in contact through a Plateau border. We obtain scaling laws, which transfer quantitatively from the elementary foam to the 2D foam. In breaking waves, weirs or wastewater plants, liquid can entrain air as it impacts the liquid reservoir Kiger and Duncan 2012 ; Erinin et al. 2023 ; Liu and Duncan 2003 . If the solution contains surfactant, bubbles can form and accumulate at the surface. The liquid will then impact a foam. The same configuration is found in the Ross Miles test, where the quantity of foam produced by drops hitting a foaming solution is measured to characterize its foaming properties Cheah and Cilliers 2005 ; Ross and Miles 1941 . Interactions between foam and a flowing fluid have also been studied in the context of oil extraction. The fluid was either air or pure water, and it generally lead to foam rupture Park and Durian 1994 ; Mensire et al. 2014 ; Del Prete et al. 2013 ; Salem et al. 2013 ; Arif et al. 2010 ; Salkin et al. 2016 . Anti-shock properties of foam motivated studies on the impact of drops or solid objects in soap films or foams Gilet and Bush 2009 ; Le Goff et al. 2014 ; Le Goff et al. 2013 ; Monloubou et al. 2015 ; Monloubou et al. 2016 ; Cohen et al. 2017 ; Yanagisawa et al. 2021 . Although they mimic most natural situations cited above, studies with jets of foaming solution were confined to an inclined jet impacting a single film Kirstetter et al. 2012 . In this letter, we study experimentally the interaction between a capillary jet and a layer of foam sandwiched between two glass plates (2D foam). The cell consists of two glass plates (17.8 mm x 12.7 mm x 1 mm) glued together with a chemical resistant epoxy adhesive (Araldite 2014). A stainless steel nozzle is fixed at the bottom of the cell. We vary the spacing d between the two glass plates between 2 and 6 mm with 3D printed wedges. The foam is produced by bubbling in a 5 wt \% Fairy solution, with a pressure controller. This allows us to produce monodisperse foams with a mean bubble radius R_{b} between 1.2 and 4.3 mm. A jet of the foaming solution is generated by imposing a pressure in a liquid reservoir with a pressure controller (Elve- flow OB1 Mk4). This reservoir is connected to nozzles of varying sizes to study laminar jets with radii R between 0.075 and 0.73 mm and speeds V between 0.4 and 6 \mathrm{m.s^{-1}} . To perform an experiment, we bubble into the solution to fill the cell to the brim with foam. The jet then plunges vertically at the top of the cell while the system is recorded with a camera (Basler a2A1920-160umPRO) and a fixed focal length objective (C23-3520-2M f35mm) during at least ten seconds at twenty frames per second. Figure 1: (a),(b) and (c) : Jet of radius 0.16 mm moving respectively at V=1\ \mathrm{m.s^{-1}} , V=2.2\ \mathrm{m.s^{-1}} , V=4.7\ \mathrm{m.s^{-1}} , in a monodisperse foam with R_{b}=1.6\ \mathrm{mm} , in a cell with a spacing d=2\mathrm{mm} . (d) Phase diagram showing the classification of experiments in three regimes for different speeds and radii. We can classify all the experiments into three regimes: ”Wet foams”, ”Tiny bubbles” and ”Thinning films”. Photographs in each regime can be found in Fig. 1 . At low speed the jet simply inflates the liquid channels, called Plateau borders. It wets the foam, as evidenced by its darkening in Fig. 1 (a). At intermediate speed the jet produces tiny bubbles within the foam channels (Fig. 1 (b)). These tiny bubbles have a radius much smaller than R_{b} and although visible in Fig. 1 (b), most of them accumulate in foam channels. In the third regime, the Plateau borders and the films are drained in the vicinity of the jet as assessed by the lighter color of the channels (Fig. 1 (c)) 1 1 1 See video examples in the supplementary materials sup . The thinning of the films can ultimately lead to bubble rupture. Note that tiny bubbles are still produced in this regime, and they accumulate at the bottom of the foam. We sum up the results of the experiments in a phase diagram in Fig. 1 (d). It appears that neither the bubble size nor the spacing d plays a major role in the effect of the jet on the foam. The phase diagram is thus controlled by V and R , with reduced transition speeds with increasing R . Figure 2: (a) Photograph of a foam and sketch of the elementary foam on which we study the interaction between a jet and a Plateau border. (b) Experimental pictures of 0.16 mm jets impacting a 40 mm wide Plateau border at V=1.1\ \mathrm{m.s^{-1}} , for the top picture and V=2.2\ \mathrm{m.s^{-1}} for the bottom one. At the connection between the jet and the plateau border, we observe respectively a meniscus toward the jet and an inverse meniscus that allows the presence of small air jets. (c) Phase diagram of jets impacting Plateau border, with an inset displaying the same data plotted according to the scaling. To study the transitions between these regimes, we create a simplified experiment. It consists of three soap films of equal dimensions, connected at 120° angles through a Plateau border(see Fig. 2 (a)). This system can be seen as an elementary unit of foam, and it allows us to control the orientation between the films and the jet. The elementary foam is formed for each experiment by dipping the frame in our foaming solution. To reproduce the transition from Wet foams to Tiny bubbles, the vertical jet directly impacts the Plateau border, as shown in Fig. 2 (a). We perform these experiments with the same jet radii as in the 2D foam experiment, with two different Plateau border lengths L . We can observe in Fig. 2 (b), that at low speeds, the meniscus between the jet and the Plateau border turns up. Stationary capillary waves can be observed at the base of the jet, which are due to a pressure mismatch between the jet and the Plateau border Gaichies et al. 2024 . Above a critical speed, we observe an inversion of the meniscus that allows the jet to entrain air threads in the film below. These thin threads of air destabilise into multiple bubbles. The radius of the air threads varies with the position of the jet relative to the Plateau border, but remains significantly smaller than R