Flying shape and aerodynamics of a full-scale flexible Olympic windsurf sail Journal: Ocean Engineering

Jishen Zhang, Gauthier Bertrand, Marc Rabaud, Benoît Augier, Marc Fermigier · 2025

Read Flying shape and aerodynamics of a full-scale flexible Olympic windsurf sail Journal: Ocean Engineering by Jishen Zhang, Gauthier Bertrand, Marc Rabaud, Benoît Augier, Marc Fermigier (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2501-13254.txt.

Introduction

Jishen Zhang and four co-authors published a 2025 wind tunnel study of a full-size Olympic windsurf sail. The sail, from the iQFOiL class, covers eight square metres and bends in the wind. Earlier studies used small rigid models, which cannot capture that bending.

The team simulated sea wind in a large tunnel and filmed the sail with stereo cameras to rebuild its flying shape. Sensors measured the forces and twisting moments at the same time. Lift, drag, and rolling measures all came out lower than the rigid-model studies had suggested. The authors argue that the sail’s deformation in real wind explains the difference. Designers of racing sails should model flexibility from the start.

Catalog record

CREATORJishen Zhang, Gauthier Bertrand, Marc Rabaud, Benoît Augier, Marc Fermigier
YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE30 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2501-13254

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Flying shape and aerodynamics of a full-scale flexible Olympic windsurf sail Journal: Ocean Engineering Jishen Zhang, Gauthier Bertrand, Marc Rabaud, Benoît Augier, Marc Fermigier Abstract The 3D flying shape of a real-scale 8 m 2 \mathrm{m^{2}} iQFOiL class windsurf sail is measured in steady state sailing configurations. The sea wind flow conditions are simulated in a large-scale wind tunnel and stereo camera imaging technique ensure the flying shape reconstruction. Sail form reconstruction allows to measure the twist of the sail profiles from bottom to top. Simultaneous aerodynamic forces and moments applied to the sail are measured via an embedded force balance. With the measured forces and moments the lift, drag and roll coefficients are determined for various wind intensity. A systematic reduction of these coefficients is observed as compared to previous studies on reduced-scale rigid sail model. We suggest that the sail deformation in the wind is crucial to explain these reductions. 1 Introduction In competitive sailing, the performance of sails is significantly influenced by their structural deformations. Except for some racing classes using rigid wings [ 1 , 2 ] , most sails are flexible structures that continuously interact with the surrounding wind flow, creating complex fluid-structure interaction (FSI) problems. This complexity is particularly pronounced in highly cambered downwind sails and deformable rigs, such as those found in windsurfing [ 3 , 4 ] . Windsurf sails, unlike traditional cruising or racing yacht sails, are designed without the support of stays and shrouds [ 5 ] . They are highly flexible and operate as part of a unified rig, with the integrated mast and boom allowing direct control by the rider. Although windsurf sails are nearly inextensible within typical wind speed ranges, the unsupported mast leads to significant deformation of the entire rig under wind loading. This unique characteristic makes windsurfing an excellent example of complex fluid-structure interactions, combining technical challenges for competitions. As such, to optimize a sail’s aerodynamic efficiency and overall performance under real sailing conditions, it is crucial to obtain precise measurements of its flying shape [ 6 ] . Various experimental techniques have been developed to measure the full-scale flying shape of sails under sea sailing conditions. These methods include Time of Flight (ToF) radar scanning [ 7 ] , monocular imaging [ 8 ] , and multiple synchronized cameras combined with both discrete [ 9 , 10 ] and continuous [ 11 ] pattern recognition algorithms. These techniques offer satisfactory accuracy and enable time resolved 3D reconstructions of the flying shape. However, measuring sail shape in steady-state conditions at sea presents challenges due to the inherently unsteady nature of the wind, both in terms of amplitude and direction [ 12 , 13 , 7 ] . To address these challenges, wind tunnel investigations using reduced-scale sail models under controlled wind conditions are commonly employed as alternatives [ 14 , 15 , 16 , 17 , 18 ] . However, such investigations may lead to aerodynamic-structural discrepancies, including mismatched Reynolds numbers as well as variations in the ratios of fabric weight to wind pressure and membrane stress to wind pressure [ 10 ] . To our knowledge, full-scale wind tunnel tests of windsurf sails have not yet been reported. In the context of windsurfing, limited attention has been given to the joint aerodynamic-structural measurements of real-scale windsurf sails. Alexander and Furniss [ 4 ] conducted measurements of the aerodynamic coefficients of 1/8-scale rigid models of a Gaastra sail, with the model shapes derived from full-scale sails. Their study specifically quantified the reduction in lift coefficient as the sail was flattened and twisted. Similarly, Mok et al. [ 19 ] examined the performance of a 1/4-scale rigid model of an iQFOiL sail [ 20 ] in a wind tunnel. The model was based on full-scale sail shapes rigged indoors without wind, and the study investigated the effects of rig-back angle and Reynolds number on aerodynamic coefficients by varying the angle of attack between 0 ∘ and 70 ∘ . In summary, both studies concentrated on aerodynamic efficiency using reduced-scale rigid models. This approach is not fully representative for flexible rigs for windsurf sails, whose deformations under wind loading can significantly alter aerodynamic performance. In the following we present wind tunnel measurements of the aerodynamic coefficients of a full-scale Olympic class iQFOiL sail, with simultaneous photogrammetric determination of its 3D flying shape. The paper is structured as follows: we begin by detailing the geometric and mechanical characteristics of the sail, including the rigging configurations used. Next, we describe the experimental setup and the wind tunnel testing conditions. We then introduce the two-camera imaging technique employed for flying shape determination, followed by a validation check of the method. Using the reconstructed 3D sail shape data, we quantitatively analyze the sail twist and mast deformation resulting from aerodynamic loading. Finally, along with the simultaneous force measurements, we provide a comprehensive analysis of the sail’s deformability on its aerodynamic performance. 2 Experimental setup 2.1 Sail characteristics We use a Severne HGO iQFOil 8m 2 sail rigged on an Apex 490 carbon fiber mast which is the approved rigging for women in the 2024 Olympic windsurf class. The mast base is flexibly linked to a Starboard iQFOiL 95 Carbon Reflex board (Fig. 1 ). The mast (4.9 m long) is slid into a sleeve at the luff (leading edge) of the sail and bent by tensioning the luff with a system of pulleys. The maximum chord length C is 2 m. Seven full battens and 5 battens of reduced-length between the 6 upper ones are distributed along the leech of the sail (trailing edge). The full battens are in compression and bend the sail in an asymmetrical cambered shape, even in the absence of wind. Their tension are adjusted by screws at the trailing edge. A double-sided carbon fiber boom (wishbone), 2.3 m long, attached to the mast, holds the clew point of the sail with the outhaul line. Adjusting the tension on the outhaul modifies the camber of the sail: a large tension on the outhaul flattens the sail and limits the twist of the sail into the wind while a small tension leads to a larger camber and increases the twist. The settings of the sail were checked by a member of the French national Olympic team. In this study, we will use two different outhaul tensions referred to as low camber and high camber. Figure 1: Severne HGO 8 m 2 sail rigged on a 95 v3 Carbon Reflex board and installed in the S6 wind tunnel at IAT Saint-Cyr l’Ecole. Green/blue checkerboards glued on the sail are used to determine the 3D shape by photogrammetry. 2.2 Wind tunnel The measurements are carried out in the large low speed S6 wind tunnel at Institut Aérotechnique Saint-Cyr-l’École 1 1 1 https://iat-en.cnam.fr/ with a test section measuring W=6 m in width and H=6 m in height. The tunnel is of open circuit blowdown type with an assembly of 36 fans located 3 m upstream of the test section. The wind in the test section is horizontal and mainly constant along the vertical axis. Turbulent intensity is between 4 and 7 \% which corresponds to a highly turbulent air flow, but

Read the complete text