Large Bidirectional Refractive Index Change in Silicon-rich Nitride via Visible Light Trimming

2024

Read Large Bidirectional Refractive Index Change in Silicon-rich Nitride via Visible Light Trimming (2024) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2412-06217.txt.

Introduction

The authors tune light chip guides with plain light in a 2024 paper. Phase-fit chips bend when builds drift by hair widths, which blocks scale-up. Their stuff is silicon-rich nitride laid by a gas craft. A green or violet beam trims its bend grade for good, in both ways. Ring guides track the trim live as tones shift by as fine as 10 picometers.

One way ran a record 49.1 nanometer red shift; the next a 10.6 blue shift. Those map to bend grade shifts of near 0.11 and minus 0.02. Heat set work drives both ways, the team prove. Two stuff grades fit the craft, both shop-true. The authors pitch trim as the fix for chip drift at scale.

Catalog record

YEAR2024
COLLECTIONPAPERS
FORMATTXT
FILE SIZE47 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2412-06217

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Large Bidirectional Refractive Index Change in Silicon-rich Nitride via Visible Light Trimming Abstract Phase-sensitive integrated photonic devices are highly susceptible to minor manufacturing deviations, resulting in significant performance inconsistencies. This variability has limited the scalability and widespread adoption of these devices. Here, a major advancement is achieved through continuous-wave (CW) visible light (405 nm and 520 nm) trimming of plasma-enhanced chemical vapor deposition (PECVD) silicon-rich nitride (SRN) waveguides. The demonstrated method achieves precise, bidirectional refractive index tuning with a single laser source in CMOS-compatible SRN samples with refractive indices of 2.4 and 2.9 (measured at 1550 nm). By utilizing a cost-effective setup for real-time resonance tracking in micro-ring resonators, the resonant wavelength shifts as fine as 10 pm are attained. Additionally, a record red shift of 49.1 nm and a substantial blue shift of 10.6 nm are demonstrated, corresponding to refractive index changes of approximately 0.11 and − 2 × 10 − 2 -2\times 10^{-2} . The blue and red shifts are both conclusively attributed to thermal annealing. These results highlight SRN’s exceptional capability for permanent optical tuning, establishing a foundation for stable, precisely controlled performance in phase-sensitive integrated photonic devices. keywords Silicon nitride; integrated photonics; optical trimming; laser annealing; tunable optical material Dmitrii Belogolovskii*, Md Masudur Rahman, Karl Johnson, Vladimir Fedorov, Andrew Grieco, Nikola Alic, Abdoulaye Ndao, Paul K. L. Yu, and Yeshaiahu Fainman Dr. D. Belogolovskii, M. M. Rahman, K. Johnson, V. Fedorov, Dr. A. Grieco, Dr. N. Alic, Prof. A. Ndao, Prof. P. K. L. Yu, Prof. Y. Fainman University of California, San Diego, 9500 Gilman Drive, La Jolla, CA 92093, USA [email protected] 1 Introduction Silicon-rich nitride (SRN) grown using plasma-enhanced chemical vapor deposition (PECVD) has numerous qualities that are outstanding for a versatile complementary metal-oxide semiconductor (CMOS) compatible integrated photonics platform. As the Si content (and with it – the refractive index) of SRN films vary with the choice of PECVD deposition and post-processing parameters, films can be grown with a refractive index (as measured at 1550 nm) ranging from 2.0 (lower Si content: Si 3 N 4 ) to 3.2 (higher Si content: Si 7 N 3 ) [1,2]. Furthermore, other linear and nonlinear optical properties of SRN are also altered remarkably with the change of silicon content, including linear optical losses and transparency window [2], nonlinear optical losses [1,3], thermo-optic coefficient [4], and third-order susceptibility ( \chi_{3} ) [1,5]. Consequently, control of these properties enables SRN films to be optimized for various applications. For example, a wide variety of nonlinear effects have been demonstrated in SRN devices, such as the DC Kerr effect [6], nonlinear Kerr switching [7], second harmonic generation [8], intermodal frequency generation [9], four-wave mixing [5], and supercontinuum generation [10]. Additionally, SRN’s relatively high thermo-optic coefficient (especially for higher Si-content films) enables implementation of efficient thermally driven phase shifters and switches [11,12]. Finally, SRN is substantially more compatible with traditional CMOS mass-manufacturing process than other materials, such as low pressure chemical vapor deposition (LPCVD) Si x N y , since the relatively low temperature of PECVD SRN deposition (350 °C) does not exceed the thermal budget of front-end-of-the-line semiconductor processes [2]. On the other hand, fabrication variability continues to represent a persistent challenge in integrated photonics, including SRN integrated platform. In particular, phase-sensitive devices, such as micro-ring resonators (MRRs), are highly sensitive to variations in the fabrication process even on the scale of 1 nm, which can lead to significant performance inconsistencies, ultimately precluding these devices from commercial and widespread use [13,14]. These random variations typically require optical devices to be biased to operating specifications using power-demanding heaters [15]. Alternatively, optical trimming, which is fine tuning of the optical properties of photonic devices post-fabrication, has been employed to compensate for such variations. However, most presented trimming methods either induce unidirectional refractive index change only, or suffer from strong relaxation, or require CMOS-incompatible materials as cladding, limiting their effectiveness. It has been well-known for nearly half a century that optical materials exposure to high-intensity visible or ultra violet (UV) light can alter their optical properties [16]. As such, some of the first approaches to trimming integrated photonic devices used UV exposure to silane-based waveguide cladding — and soon after, Si x N y waveguide cores — to substantially shift the center wavelengths of filters and ring resonators [17,18]. In the time since, a wide variety of methods and optical materials have been proposed to trim optical properties of integrated components, including further developments of continuous wave (CW) UV and visible light exposure [19-22], pulsed laser irradiation [23], electron beam exposure [24,25], and localized annealing of regions exposed to ion implantation [26-31]. These methods can introduce waveguide effective index changes on the order of 10^{-3} to 10^{-2} , which is sufficient for many applications [26,30]. However, several of these methods require exotic non-CMOS-compatible materials to sensitize the optical structure to the applied stimulus, such as chalcogenides, phase change materials, tunable polymers, and liquid crystals [17,19,21,32]. Other methods require trimming to be performed on waveguides prior to the application of the final cladding, necessitating the use of temporary cladding and adding complexity to the trimming process [33]. Recently, simple CMOS-compatible post-fabrication trimming of structures has been demonstrated using localized annealing from on-chip heaters included in the chip design [26-31]. While this method is simple and effective, it requires Ge implantation of the waveguide and is capable only of decreasing the refractive index of the optical material. In fact, most of those mentioned above techniques are not capable of post-fabrication trimming in both directions. Exploring the feasibility of trimming SRN via laser annealing is of significant interest. It is widely recognized that rapid thermal annealing (RTA) of SRN at high temperatures (typically >600 °C) leads to the dissociation of Si-H bonds, significant hydrogen (H) desorption, reduced nitrogen (N) content, and an increased concentration of Si-Si bonds [34-36]. Conversely, studies have shown that RTA at lower temperatures (<600 °C) causes bond redistribution (such as Si-Si, Si-N, Si-H, N-H), leading to an increase in Si-H and Si-N bond concentration at the expense of N-H and Si-Si bond concentration [34,35]. Such structural changes should inevitably result in permanent refractive index change necessary for trimming. At the same time, a relatively low thermal conductivity of PECVD SRN thin film was reported, in the range of 0.45 to 4.5 W m -1 K -1 [37], much lower then that of c-Si, which is 148 W m -1 K -1 [38]. This suggests that SRN can efficiently localize heat, which is favorable for localized laser annealing where high temperatures are required. When a thin film absorbs laser radiation, the resulting temperature increase can be approximately estimated using the equation T_{max}=T_{0}+P/(w_{0}k\sqrt{\pi}) , where T_{max} is the maximum temperature, T_{0} is the room temperature, w_{0} is the mode diameter of the Gaussian beam, k is the thermal conductivity, and P is the optical power [39]. Assuming that SRN’s thermal conductivity is roughly in the middle, for example, k = 1.7 W m -1 K -1 , and P = 40 mW, w_{0} = 10 \mu m, we estimate T_{max} = 1350 °C, large enough to activate both mechanisms that are responsible for thermal annealing [34-36], making SRN an excellent candidate for trimming studies.

Read the complete text