Solution-Processed Oxide Thin Films for Perovskite Photovoltaics Cooperative Research and Development Final Report CRADA Number: CRD-23-23493 NLR Technical Contact: Lance Wheeler The National Laboratory of the Rockies is a national Technical Report laboratory of the U.S. Department of Energy, NLR/TP-5K00-99016 Office of Critical Minerals and Energy Innovation, February 2026 operated under Contract No. DE-AC36-08GO28308. This report is available at no cost from the National Laboratory of the Rockies (NLR) at www.nlr.gov/publications. Solution-Processed Oxide Thin Films for Perovskite Photovoltaics Cooperative Research and Development Final Report CRADA Number: CRD-23-23493 NLR Technical Contact: Lance Wheeler Suggested Citation Wheeler, Lance. 2026. Solution-Processed Oxide Thin Films for Perovskite Photovoltaics: Cooperative Research and Development Final Report, CRADA Number CRD-23-23493. Golden, CO: National Laboratory of the Rockies. NLR/TP-5K00-99016. https://www.nlr.gov/docs/fy26osti/99016.pdf. The National Laboratory of the Rockies is a national Technical Report laboratory of the U.S. Department of Energy, NLR/TP-5K00-99016 Office of Critical Minerals and Energy Innovation, February 2026 operated under Contract No. DE-AC36-08GO28308. National Laboratory of the Rockies 15013 Denver West Parkway This report is available at no cost from the National Laboratory Golden, CO 80401 of the Rockies (NLR) at www.nlr.gov/publications. 303-275-3000 • www.nlr.gov This work was authored by the National Laboratory of the Rockies for the U.S. Department of Energy (DOE), operated under Contract No. DE-AC36-08GO28308. Funding provided by U.S. Department of Energy Office of Energy Efficiency and Renewable Energy Solar Energy Technologies Office. The views expressed herein do not necessarily represent the views of the DOE or the U.S. Government. This work was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, nor any of their contractors, subcontractors or their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or any third party’s use or the results of such use of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise, does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof or its contractors or subcontractors. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof, its contractors or subcontractors. This report was produced when the laboratory operated as the National Renewable Energy Laboratory (NREL). The laboratory is now the National Laboratory of the Rockies (NLR). This report is available at no cost from the National Laboratory of the Rockies (NLR) at www.nlr.gov/publications. U.S. Department of Energy (DOE) reports produced after 1991 and a growing number of pre-1991 documents are available free via www.OSTI.gov. Cover photos (clockwise from left): Josh Bauer, National Laboratory of the Rockies 61725; Visualization from National Laboratory of the Rockies Insight Center; Getty-181828180; Agata Bogucka, National Laboratory of the Rockies 91683; Dennis Schroeder, National Laboratory of the Rockies 51331; Werner Slocum, National Laboratory of the Rockies 67842. National Laboratory of the Rockies prints on paper that contains recycled content. Cooperative Research and Development Final Report Report Date: December 31, 2025 In accordance with requirements set forth in the terms of the CRADA agreement, this document is the CRADA final report, including a list of subject inventions, to be forwarded to the DOE Office of Scientific and Technical Information as part of the commitment to the public to demonstrate results of federally funded research. Parties to the Agreement: NexTC Corporation CRADA Number: CRD-23-23493 CRADA Title: Solution-Processed Oxide Thin Films for Perovskite Photovoltaics Period of Performance: 8/2/2023 – 8/1/2025 Responsible Technical Contact at NLR: Lance Wheeler | Lance.Wheeler@nlr.gov Name and Email Address of POC at Company: Cory Perkins | Cory@nextcmaterials.com Sponsoring DOE Program Office: Office of Critical Minerals and Energy Innovation (CMEI), Solar Energy Technologies Office Joint Work Statement Funding Table showing DOE Commitment: NLR Shared Resources Estimated Costs a/k/a Government In-Kind Year 1 $55,000.00 TOTALS $55,000.00 1 Executive Summary of CRADA Work: The overarching goal of the voucher project is to evaluate the suitability of NexTC materials as functional layers in perovskite photovoltaic technology. There are several different perovskite device configurations that are being pursued for commercialization. Most are superstrate configuration (light enters the device through the glass substrate) and can be subdivided into two categories: PIN and NIP. At minimum, PIN devices have a transparent conductor (typically Indium Tin Dioxide [ITO] or Fluorine-Doped Tin Oxide [FTO]) and hole transport layer (HTL) deposited on glass before the perovskite is deposited. Alternatively, NIP devices have a transparent conductor and electron transport layer (ETL) deposited before the perovskite is deposited. NexTC produces several inks that can be deposited to replace or modify the transparent conductor and/or the ETL or HTL, depending on the device. NLR will produce PIN and NIP perovskite devices on substrates that have been coated by NexTC and compare to NLR- standard devices that perform among the best for research labs across the world. The work will ultimately expose NexTC products to the up-and-coming perovskite PV industry. CRADA benefit to DOE, Participant, and US Taxpayer: • Assists laboratory in achieving programmatic scope Summary of Research Results: The overall goal of the research is to provide an initial evaluation of NexTC materials for application in metal halide perovskite (MHP) solar cells. Metal halide perovskite solar cells are constructed in numerous architectures. We have chosen three representative stacks to reflect the most popular architectures being pursued for commercialization (Figure 1). There are two single- junction architectures, PIN stack and NIP stack. In the PIN stack, NexTC’s indium tin oxide (ITO) will be explored on the hole collection side of the device as the current-collecting electrode. For the NIP, NexTC’s tin oxide (SnO2) will be applied as the electron transport layer. The third architecture is the two-terminal tandem, where NextTC’s material will serve as a recombination layer between a silicon absorber and metal halide perovskite layer. To address the viability of the three architectures, five tasks were devised. Fig. 1. Diagrams of the three representative MHP solar cell architectures explored in this project. The red box in each stack highlights where the NexTC material is being applied. The tandem architecture is simplified to show which layers were explored in this work. 2 Task 1: Coat NLR substrates NLR will mail NexTC various device substrates, including: 1) Glass for ITO characterization and PIN perovskite devices, 2) ITO-coated glass for Tin Dioxide (SnO2) characterization and NIP perovskite devices, and 3) silicon for coating characterization. Each substrate will be coated with 2 different thicknesses (10 +/- 5 nm and 50 +/-5 nm for SnO2 and 100 +/- 10 nm and 200 +/-10 nm for ITO) and 2 different annealing conditions. Task 1 Results: The goal of this task was to exchange and coat samples for characterization of NexTC materials for the three different MHP solar cell applications. NLR mailed NexTC various device substrates, including: 1) Glass for ITO characterization and PIN perovskite devices, 2) ITO- coated glass for SnO2 characterization and NIP perovskite devices, and 3) silicon for coating characterization. Each substrate was coated with 2 different thicknesses (10 +/- 5 nm and 50 +/-5 nm for SnO2 and 100 +/- 10 nm and 200 +/-10 nm for ITO) and 2 different annealing conditions. Table 1. Substrates, coating material, and annealing conditions that were produced for characterization. Substrate # Substrates Substrate Coating Target Annealing T Material Thickness (C) (nm) Glass 3 Glass ITO 150 +/- 10 500 Glass 3 Glass ITO 250 +/- 10 300 Glass 3 Glass ITO 150 +/- 10 500 Glass 3 Glass ITO 250 +/- 10 300 Glass/ITO 3 Glass/ITO SnO2 10 +/- 5 500 Glass/ITO 3 Glass/ITO SnO2 10 +/- 5 300 Glass/ITO 3 Glass/ITO SnO2 50 +/- 5 500 Glass/ITO 3 Glass/ITO SnO2 50 +/- 5 300 Textured SI 3 Textured SI ITO 150 +/- 10 500 Textured SI 3 Textured SI ITO 250 +/- 10 300 Textured SI 3 Textured SI ITO 150 +/- 10 500 Textured SI 3 Textured SI ITO 250 +/- 10 300 A limited number of samples were returned by NexTC, which limited the number of studies that could be performed during the project. All samples mailed back from NexTC were SnO2 deposited on Glass/ITO, so most studies focused on these stacks, which corresponded to the NIP stack shown in Figure 1. 3 Task 2: Electrochemical Characterization NLR will evaluate samples that will be coated with SnO2, electrochemical characterization to evaluate selectivity of the contact to transport electrons and block holes Task 2 Results: Hole blocking was an important characteristic of an electron transport layer in an MHP solar cell. The goal of this work was to evaluate the hole-blocking selectivity of the SnO2 layer. NLR had developed a technique dedicated to evaluating transport layers based on electrochemistry where the sample was immersed in an electrolyte with a Fe2+/Fe3+ with a 0.5 M KCl supporting electrolyte (Figure 2). Fig. 2. Diagram of electrochemical cell setup used to evaluate hole-blocking of NexTC SnO2 layer. The sample formed a semiconductor-electrolyte junction with band-bending induced in the SnO2 (Figure 1a). Control measurements of the ITO without SnO2 yielded a cyclic voltammogram with the classic duck-shaped curve of a reversible redox couple (Figure 1b). There was no blocking of electrons or holes in this case. In contrast, there was a sharp cathodic onset observed when SnO2 was coated on the ITO (Figure 1b). Fig. 3. (a) Diagram illustrating the semiconductor-electrolyte junction. (b) Current density as a function of potential relative to Silver/Silver Chloride (Ag/AgCl) for three different SnO2 samples and an ITO control. 4 We compared two NexTC samples to a standard sample fabricated at NLR. The NLR sample is composed of tin oxide (SnOx), where x varies depending on oxidation state and manufacturing conditions, nanoparticles (NPs) because this composition is common in the MHP literature, and has been vetted in many other projects at NLR. The NLR NP sample exhibits hole blocking behavior indicated by limited current as positive voltages. The 16.7 nm SnO 2 samples obtained from NexTC show slightly more anodic current, indicating poorer hole-blocking. This likely indicates the presence of pinholes in the film since there is also a peak close to 0 V, which likely corresponds to the ITO beneath the SnO2. In contrast, the thicker samples (48.8 nm) that were annealed at lower temperatures show a near-ideal response, with negligible anodic current and a sharp onset at ~0.75 V. Task 3: Optical and electrical characterization NLR will evaluate samples coated with ITO or SnO2 will be characterized using UV-vis spectroscopy to evaluate optical transmission of the samples. For ITO on glass and Si, the sheet resistance will be evaluated using 4-point probe measurements. Task 3 Results: The goal of this task was to have NLR evaluate the optical and electrical properties of samples coated with ITO or SnO2 characterized using ultraviolet-visible-near-infrared (UV-vis-NIR) spectroscopy to evaluate optical transmission of the samples. For ITO on glass and silicon (Si), the goal was to evaluate sheet resistance four-point probe measurements. However, ITO samples were not received, so sheet resistance measurements were not performed. We compared two NexTC samples to a standard sample fabricated at NLR and an ITO control sample. The NLR sample was composed of SnOx NPs. UV-vis-NIR transmission spectra of the control ITO sample exhibited a maximum transmission of ~90% at 500 nm with a tail at higher wavelengths due to free carrier absorption of the ITO. Other features in the spectrum were due to thin film interference. For ideal solar cell applications, the SnO2 layer should not have introduced any reflection or parasitic absorption (reduced transmission), which would have decreased the current of the device. Application of SnO2 modified the transmission spectra due to new interfaces that introduced additional interference but no significant decrease in transmission (Figure 4). This was true for the NLR NP control sample as well as the NexTC samples, though interference effects changed the structure of the spectrum. For instance, the peak transmission was shifted to lower wavelengths for the 48 nm sample, relative to ITO. Transmission also increased at high energy. One noticeable difference was the decrease in free carrier absorption when the SnO2 was annealed at 500 °C. The higher annealing temperature likely degraded the ITO below by reducing the number of free carriers. Overall, however, the optical quality of the SnO2 samples was high. 5 Fig. 4. Ultraviolet-visible-near infrared transmittance spectra for three different SnO2 samples and an ITO control. Task 4: Perovskite device fabrication and characterization NLR will evaluate ITO/glass samples coated by SnO2 at NexTC will be coated with remaining layers to form NIP perovskite PV devices. Glass samples coated with ITO at NexTC will be coated with the remaining layers to form PIN perovskite PV devices. Devices will be tested using currentvoltage characterization (reverse/forward sweeps and stabilized power output) with six or more individual pixels for each dependent variable for statistical confidence. Control devices with all layers deposited by NLR will be fabricated for comparison to devices with NexTC coatings. If characterization of Si surface coatings are continuous and conformal, 2- terminal tandem devices will be fabricated on the ITO-coated Si and characterized the same way single-junction devices are tested. Task 4 Results: The goal of this task was to integrate NexTC materials into device stacks that were completed and measured by NLR. NLR evaluated ITO/glass samples coated with SnO2 at NexTC where NLR deposited the remaining layers to form NIP perovskite PV devices. Glass samples coated with ITO at NexTC would have been coated with the remaining layers at NLR to form PIN perovskite PV devices. However, ITO samples were not received. NIP devices were tested using illuminated current density-voltage characterization (reverse/forward sweeps) with six or more individual pixels for each dependent variable for statistical confidence. Control devices with all layers deposited by NLR were fabricated for comparison with devices with NexTC coatings. Control devices exhibited rectifying behavior and a curve shifted away from the origin, indicating collection of photocurrent (Figure 5). Devices exhibited open-circuit voltages as high as 1 V and short-circuit current as high as 20 mA cm-2. Champion devices showed power conversion efficiency of 16%. 6 Fig. 5. Current density-voltage curves for NIP MHP devices fabricated with all layers deposited at NLR. In contrast, NIP devices fabricated with SnO2 layers from NexTC showed little rectification, no photovoltage, and high negative currents (Figure 6). Each of these attributes pointed to shorts in the device where the SnO2 layer did not protect the ITO from coming in contact with other layers in the device. Fig. 6. Current density-voltage curves for NIP MHP devices fabricated with SnO2 layers deposited by NexTC. If characterization of Si surface coatings were continuous and conformal, 2-terminal tandem devices will be fabricated on the ITO-coated Si and characterized the same way single-junction devices are tested. However, ITO layers were not of sufficient quality (See Task 5). 7 Task 5: Coating quality characterization NLR will evaluate ITO samples coated on silicon, optical microscopy and profilometry will be used to identify pinholes and evaluate large-area conformal coverage (1> mm scale). Atomic force microscopy and scanning electron microscopy will be used to evaluate smaller areas (<1 mm). Task 5 Results: The goal of this task was to evaluate the possibility of NexTC’s ITO to serve as a recombination layer in a silicon/MHP tandem architecture. NLR evaluated ITO samples coated on silicon, and optical microscopy and profilometry were used to identify pinholes and evaluate large-area conformal coverage (greater than 1 mm scale). Atomic force microscopy and scanning electron microscopy were used to evaluate smaller areas (less than 1 mm). This task was not completed entirely as planned since samples coated on silicon were not received. Instead, NLR obtained ITO precursor ink from NexTC. It was assumed that spin- coated films of ITO would not conformally coat textured Si, so NLR performed spray-coating, which was a method more capable of conformally coating a non-planar surface. Rather than coating on textured Si, initial trials were performed on glass with the intention of moving to textured Si if films were successful. A spray-coating study was performed with different solvents to determine if conformal films could be achieved. All spray-coating runs were performed in a nitrogen (N₂)-purged glovebox at a temperature of 300 °C to decompose the incident precursor with a pump rate of 0.05 mL min⁻¹, ink concentration of 0.015 M, and N₂ flow rate of 6 L min⁻¹. Optical microscopy was performed on samples deposited from different inks. Both n-methylpyrrolidone (NMP, Figure 7a) and dimethylformamide (DMF, Figure 7b) produced films with roughness that exceeded 100 µm. Combining both solvents yielded a similar film (Figure 7c). However, when combining DMF with a more volatile solvent such as acetonitrile (ACN), the film roughness was reduced. Though small particles could be observed, the film quality was more continuous and may have pointed to a way forward for this method. 8 Fig. 7. Optical micrographs of ITO samples spray-coated onto glass from (a) n-methylpyrrolidone (NMP), (b) dimethylformamide (DMF (c) DMF and NMP (equal volume), (d) DMF and acetonitrile (ACN) (equal volume). Task 6: CRADA Final Report: Preparation and submission of a final report will be delivered to NLR’s Technology Transfer Office. Task 6 Results: This report serves to meet the requirement for the CRADA Final Report with preparation and submission in accordance with the agreement’s Article X. AI Acknowledgment: The author(s) acknowledge the use of generative AI in the preparation of this report. Subject Inventions Listing: None. ROI#: None. 9