Buried Fiber-Optic Geolocalization with Distributed Acoustic Sensing Khen Cohen, Natanel Nissan, Ofir Nissan, Ariel Lellouch Abstract We present a scalable method for geolocalizing buried fiber-optic cables using Distributed Acoustic Sensing (DAS) and traffic-induced quasi-static seismic signals. Assuming access to one end of the fiber, the method fuses DAS measurements with vehicle trajectories obtained from either video tracking or vehicle-mounted GPS. The fiber geometry is estimated by minimizing the mismatch between the measured and physics-based synthetic strain-rate maps. The framework combines a matched-filter initialization with neural-network-based trajectory optimization, enabling robust convergence under realistic noise and trajectory-uncertainty conditions. Simulation and field experiments demonstrate sub-meter localization accuracy, often on the order of tens of centimeters, and strong agreement with manual calibration by tap-testing. This approach provides a practical tool for mapping poorly documented underground fiber infrastructure and for supporting urban sensing applications. I Introduction The urban environment contains dense underground networks of fiber-optic cables. However, utility records often suffer from significant positional inaccuracies. A comparative study that examined utility records against Subsurface Utility Engineering (SUE) investigations found that only 32% of utilities aligned within 2 feet ( \approx 0.6m ), while approximately 21% deviated by more than 20 feet ( \approx 6.1m ) [ 3 ] . As a consequence, frequent damage to existing but poorly mapped fiber-optic infrastructure during construction and excavation leads to IT service disruptions, repair costs, and project delays. In dense urban settings, sub-meter mapping accuracy is therefore critical to reduce accidental damage during construction. The challenge is compounded by the physical properties of fiber-optic cables: because both the fiber and its protective casing are typically non-conductive, conventional underground utility detection methods, such as electromagnetic (EM) detection and ground-penetrating radar (GPR), often cannot reliably locate fiber-optic infrastructure. However, the existence of manholes or optical cabinets, visible at the surface, can be leveraged to constrain fiber routes. Over the past decade, Distributed Fiber Optic Sensing (DFOS) technologies, particularly Distributed Acoustic Sensing (DAS), have shown that existing telecommunication fiber can be transformed into high-resolution seismic monitoring arrays [ 41 , 11 , 24 , 43 ] . Many studies have extended this capability to urban environments and demonstrated the value of vehicle-signal extraction for traffic monitoring and management [ 23 , 33 , 4 , 21 , 8 ] . The main advantage of DAS over traditional seismic sensors, which is the meter-scale spatial channel resolution it offers, is fully realized only when the fiber path is precisely known [ 22 ] . A key prerequisite for urban DAS applications is thus the accurate geolocalization of the fiber itself. In addition to the need for the location of the fiber, the DAS measurements are directional along the fiber axis and are therefore inherently tied to fiber geometry [ 26 , 8 , 34 , 37 , 17 ] . Hence, accurate fiber geolocalization is also crucial for correct interpretation of the directional sensitivity of the DAS measurements. Consequently, precise mapping of underground fiber cables, especially legacy installations with incomplete documentation, remains a central barrier to large-scale DAS deployments [ 36 , 1 ] . Early fiber-localization methods relied on tap tests, in which seismic signals were generated at known surface positions (e.g., with weight drops or sledgehammers) and then matched to peak DAS channel responses in strain or strain rate [ 20 ] . More recent approaches automated this idea by synchronizing vehicle-mounted GPS with DAS data, achieving meter-level localization along the roadway direction, while cross-road (perpendicular) accuracy remains limited [ 38 ] . A complementary strategy uses access points (manholes) as localization anchors. In DAS data, manholes can often be identified because the spooled slack fiber inside them exhibits a seismic response different from that of straight buried segments, including under distant earthquake wavefields [ 5 , 18 , 2 ] . Although manhole detection provides useful anchor points, it is generally insufficient on its own to recover the full fiber trajectory at sub-meter precision [ 5 ] . Fiber geolocalization used raw DAS measurements introduce additional challenges. The recordings are frequently contaminated by multiple noise sources such as optical fading, environmental interference, and instrument noise, all of which degrade the signal-to-noise ratio (SNR) [ 12 , 42 ] . The phase estimation of large strains, such as those induced by direct tap-test hits above the cable, is unstable and depends on the specific phase unwrapping algorithm [ 14 ] . Extracting useful information from vehicle signals is complicated by near-field effects and variable source characteristics, which can introduce substantial uncertainty if not modeled carefully [ 10 ] . Recent work has highlighted the need for advanced deep-learning pipelines to mitigate these artifacts, as well as the computational burden imposed by continuous DAS acquisition and massive data volumes [ 7 ] . Therefore, even when DAS data are available, deriving reliable geometric information remains nontrivial and motivates the development of robust, automated localization methods. In this study, we present an automatic and scalable method for sub-meter localization of underground fiber utilities. As in prior work, we leverage ambient traffic noise. However, whereas traditional approaches often use only the maximum DAS amplitude at the channel nearest to a vehicle as a location proxy, our method models the full spatiotemporal DAS response induced by moving vehicles and estimates the fiber trajectory that best fits the measurements. Figure 1 provides an overview of the workflow. We show that, with vehicle trajectory information obtained either from vehicle-mounted GPS or from camera-based tracking, the method achieves sub-meter localization accuracy under realistic conditions. The remainder of this paper is organized as follows: Section II presents the mathematical and physical background; Section III introduces the localization framework, including model-based sensitivity analysis and a two-stage optimization strategy; Section IV reports simulation results across multiple operating conditions; Section V presents two experiments on the same street (camera-based and GPS-based); and Section VI concludes with limitations and future directions. Fig. 1: Diagram of the fiber localization method. (A) A driving car is continuously recorded by a camera or GPS, while a nearby DAS system measures seismic waves via the optical fiber (orange). The gray fiber represents an initial guess of the fiber’s location. (B) During the optimization process, the synthetic strain rate generated from the estimated fiber path converges toward the real strain rate measured by the DAS. (C) Experimental DAS recordings of strain rate versus time at different locations in the presence of a moving vehicle. II Background II-A Fiber Location and Coordinate System We consider a buried optical fiber of total length L_{\text{tot}} , accurately measurable from OTDR readings. We define a global Cartesian coordinate system with orthonormal basis vectors \left(\hat{\mathbf{x}},\hat{\mathbf{y}},\hat{\mathbf{z}}\right) . The spatial location of the fiber in this coordinate frame is described by a 3D curve parameterized by the arc-length coordinate l (measured from a reference point along the fiber): \mathbf{S}(l)=\big(x(l),\;y(l),\;z(l)\big)\ . (1) As the DAS interrogator outputs measurements at discrete intervals along the fiber, we represent its layout as a sequence of N uniformly spaced points along its path: \mathbf{S}_{n}=\big(x_{n},y_{n},z_{n}\big),\quad n=1,\dots,N\ . (2) With N determined by the fiber length and spatial sampling interval \Delta x , i.e., N=\frac{L_{\text{tot}}}{\Delta x}\ , (3) we refer to the spatial sampling interval as a segment . In this study, the optical acquisition parameters yield \Delta x\approx 1\,\mathrm{m} . We emphasize that this value is not the same as spatial resolution, because DAS measurements are averaged over a finite gauge length [ 14 ] , which is typically on the order of 3-10 m in urban monitoring settings. II-B Distance Metric Between Possible Fiber Trajectories To quantify the discrepancy between the true and predicted trajectories, denoted by \mathbf{S}_{n} and \mathbf{\hat{S}}_{m} , respectively, we use the Hausdorff distance between the corresponding point sets: \displaystyle d_{H}(\mathbf{S}_{n},\mathbf{\hat{S}}_{m})=\max\bigg\{ \displaystyle\sup_{\mathbf{x}\in\mathbf{S}_{n}}\inf_{\mathbf{y}\in\mathbf{\hat{S}}_{m}}\|\mathbf{x}-\mathbf{y}\|,\; (4) \displaystyle\sup_{\mathbf{y}\in\mathbf{\hat{S}}_{m}}\inf_{\mathbf{x}\in\mathbf{S}_{n}}\|\mathbf{x}-\mathbf{y}\|\bigg\}\ . This metric is well suited for trajectory comparison because it quantifies the maximum mismatch between the two curves, ensuring that localized deviations are not overlooked. The Hausdorff distance is zero only when the two trajectories coincide as point sets. In addition, it naturally handles trajectories with different numbers of sampled points. All trajectory-distance evaluations in this paper use this definition. II-C Camera Model We adopt the camera modeling framework described in [ 30 ] . Each event i captured by the camera at time t is associated with a pixel location (x_{i}(t),y_{i}(t)) in the image plane. The relationship between pixel coordinates and 3D world coordinates is given by the camera projection matrix P : \mathbf{p}_{i}\propto P\,\mathbf{X}_{i}\ , (5) where \mathbf{p}_{i} is the homogeneous pixel coordinate and \mathbf{X}_{i} is the corresponding homogeneous 3D point. In general, this transformation is not directly invertible, as all points lying along the same camera ray are projected to the same pixel. To resolve this ambiguity, we assume a locally planar and horizontal ground surface. The 3D position of each observed point is then determined by intersecting its camera ray with the ground plane. This assumption enables a direct mapping from pixel coordinates to 3D object locations in the global coordinate system. Throughout this paper, we assume that vehicles move along the x axis, the y axis represents lateral (cross-road) offset, and the z axis represents depth. II-D Vehicle-Induced Seismic Wavefield in Fiber Coordinates Moving vehicles generate a seismic wavefield with two principal components [ 31 , 40 , 39 ] . The first is a quasi-static component (frequencies <1 Hz), arising from elastic ground deformation under the vehicle load. The second is a dynamic component, typically in the \sim 2-20 Hz range, dominated by Rayleigh-type surface waves excited by road-wheel interactions. Although recent studies have used rigorous 3D forward modeling to characterize the full wavefield generated by heavy moving sources (e.g., high-speed trains) [ 35 ] , our geometric-localization framework for urban settings focuses on quasi-static deformation. Prior studies [ 31 , 39 ] show that the Flamant-Boussinesq solution for a point load is an effective approximation of the recorded signal. The displacement field u_{x}(x,y,z) along the x-axis, produced by a vertical point load F at the origin, is given for a straight fiber by: u_{x}(x,y,z)=\frac{F}{4\pi G}\frac{x}{r^{2}}\left(\frac{z}{r}+\frac{2\nu-1}{1+\frac{z}{r}}\right)\ , (6) where (x,y,z) are coordinates in the global frame, r=\sqrt{x^{2}+y^{2}+z^{2}} is the Euclidean distance from the load point to the measurement point, and G and \nu are the shear modulus and Poisson’s ratio of the subsurface, assumed homogeneous and known. However, in the case of a general fiber layout, the displacements are measured along the trajectory rather than a specific axis. In addition, the coordinates (x,y,z) should be expressed in the fiber coordinate system rather than in the global frame. Appendix VII provides the corrected formulation in fiber coordinates. While we supply it for completeness, we find that this correction has a negligible effect on the results reported in this study. DAS systems, as opposed to traditional sensors, do not measure point strain or strain rate. Instead, they measure the accumulated strain/strain-rate along a gauge length, which is typically in the range of 3-10 m in urban monitoring settings. The directional strain rate at position l along the fiber and time t is thus equivalent to the differential directional displacement rate along the gauge length: \dot{\varepsilon}_{\mathrm{DAS}}(l,t)=\frac{1}{\Delta x}\left[\dot{u}_{l}\left(l+\frac{\Delta x}{2},t\right)-\dot{u}_{l}\left(l-\frac{\Delta x}{2},t\right)\right]\ , (7) where \dot{u}_{l} is the temporal derivative of displacement along the fiber direction. In practice, the load from a moving vehicle can be represented as a superposition of point loads at the wheel locations. The total strain-rate signal recorded by the DAS is then obtained by summing the contributions from all loads with appropriate time-shifts. For the quasi-static part of the seismic wavefield, the response is assumed immediate and no temporal propagation effects need to be taken into account. III Fiber Localization Method In this section, we present the methodology used to localize the optical fiber. We begin with a sensitivity analysis based primarily on Eq. 7 . We then introduce a two-stage localization framework: (i) an initialization step based on matched filtering of the strain-rate map, and (ii) a neural-network-based optimization stage that estimates fiber coordinates. Together, these components enable high-precision fiber localization. An accurate model for a vehicle load requires representing each wheel as a separate point load. However, our analysis shows that this model improved overall accuracy only by a few centimeters on average, and only in some of the tests, for our data acquisition configuration with a 10-m gauge length. In addition, estimating axle distance may not be straightforward for large vehicles. Therefore, we model vehicles as a point load. The vehicle trajectory is obtained from a camera tracking algorithm or vehicle-mounted GPS, as will be discussed in V . The subsurface parameters, shear modulus G and Poisson ratio \nu , are assumed spatially constant. The absolute value of G is not needed as the synthetic map is normalized (see III-C ). However, \nu significantly influences the shape of the signal. Previous studies have also attempted to estimate it directly from quasi-static measurements [ 39 ] . The spatial homogeneity assumption may thus break down over long distances or in areas of sharp lithological changes. Therefore, we apply our method to road intervals of up to approximately 100 m to limit such changes. III-A Sensitivity Analysis We begin with a simplified scenario, in which a single point load moves approximately parallel and at a constant horizontal distance to the optical fiber. A gauge length of 10 m is used for the DAS strain-rate generation. In this setting, the first step of localization is estimating the fiber coordinate along the road direction (the x axis). Under the quasi-static approximation, for any fixed time t , the displacement profile along the fiber reaches its maximum magnitude at the point closest to the moving load. Equivalently, the corresponding strain-rate signal crosses zero at that point (hereafter, the crossing point ). Thus, when the vehicle is observed at position x(t) , the channel index associated with the strain-rate zero crossing, l(t) , identifies the nearest fiber location to the vehicle. The x coordinate of that fiber point is then estimated from the known x(t) at the same time. The more challenging steps are estimating the fiber’s burial depth and horizontal distance from the vehicle. Figure 2 illustrates synthetic signals recorded for different geometrical conditions. Fig. 3 shows a 2D contour in which the response width generally increases with both horizontal and vertical distance from the vehicle to the fiber, together with a sensitivity map. Around a horizontal distance of approximately 2 m, the two opposite-sign strain-rate pulses (left negative, right positive) begin to merge into a single broader feature. It also shows that the recorded signals are highly sensitive to installation depth, which can induce significant waveform distortion with increasing installation depth. The effect of the horizontal distance is very significant for the first few meters and gradually decreases with distance. As a first-order proxy, we analyze the spatial width of the DAS signal. We quantify it as the standard deviation of the absolute strain-rate profile at a fixed time. Our sensitivity analysis suggests that if either horizontal distance or installation depth are known, the other can be estimated from the strain-rate width profile. However, in the more common case where both are uncertain, aside from practical burial-depth bounds (typically between 0.5 to 1.5 m), this approach alone is insufficient for complete localization, and the full recorded signal might be required. Moreover, as Fig. 3 suggests, when the horizontal distance exceeds approximately three times the installation depth, the sensitivity of the width to both parameters decreases dramatically. In such cases, estimating the horizontal distance becomes even more challenging, even given reasonable knowledge about installation depth. We thus conclude that the width is a useful heuristic that should, nonetheless, be used carefully. Fig. 2: Spatio-temporal strain rates of a point object moving at constant speed for different geometrical settings. The spatial-only strain rate, extracted at t=5 s, is also shown. Left - different horizontal distances for a fixed depth of 1 m. The spatial strain-rate signature broadens with horizontal distance, and stabilizes around 4 m. Right - different fiber depths for a fixed horizontal distance of 4 m. Increase of burial depth complexifies recorded signal. Fig. 3: Top: Calculated spatial width for varying horizontal (Y) and vertical (Z) distances. The width increases with both, but in a distinct pattern. Bottom: The gradient magnitude of the response width map, indicating sensitivity. III-B Correlation-Based DAS Channel Assignment Fiber geometry estimation that directly utilizes the predicted response derived in Sec. II-D (Eq. 7 ) failed. Instead, we first conduct a coarser geometry estimation that provides a better initial model to the full optimization that uses the full properties of the signal. We note that the strain-rate pattern predicted by Eq. 7 exhibits an antisymmetric localized pulse that can be well approximated by the temporal derivative of a Ricker (Mexican-hat) wavelet, given in Eq. 8 . This choice is motivated by its convenient analytic form and widespread use in seismic data analysis [ 31 , 28 , 19 , 29 ] . We therefore use the Ricker derivative not as a replacement to the full analytic model, but as a practical matched-filter template that captures the dominant antisymmetric structure. Although the exact waveform varies with load distribution (e.g., wheel spacing and vehicle length) and burial depth, empirical evaluations (Appendix VIII ) show that the Ricker-derivative family provides a stable and geometry-consistent initialization. This approximation is used only in the initialization stage; the second-stage optimization in Sec. III-C relies on the full physics-based model. The Ricker wavelet at scale \sigma is defined as \psi_{\sigma}(t)=\frac{2}{\sqrt{3\sigma}\,\pi^{1/4}}\left(1-\frac{t^{2}}{\sigma^{2}}\right)e^{-t^{2}/(2\sigma^{2})}\ , (8) and its temporal derivative serves as the matched-filter kernel. The scale parameter \sigma directly controls the waveform spread: larger values produce broader, more slowly varying responses, whereas smaller values yield sharper, more localized features. Because neither the lateral offset nor the exact burial depth is known a priori, we treat \sigma as a variable representing the width broadening imposed by both installation depth and parallel offset between the fiber and the road. For each time frame, we compute the one-dimensional convolution between the DAS strain–rate across all channels and a bank of filters \psi^{\prime}_{\sigma_{k}}(-t) for \sigma_{k}\in[\sigma_{\min},\sigma_{\max}] . In the presence of additive noise, matched filtering maximizes the output signal-to-noise ratio [ 32 , 25 ] , herein enabling reliable detection of the crossing point. Thus, for each time frame, we select the scale \sigma^{*}(t) and channel index l^{*}(t) that maximize the absolute filter response. Algorithm 1 summarizes this procedure, and Fig. 4 illustrates the resulting crossing point detections across different timeframes. Input: DAS strain-rate matrix \dot{\varepsilon}(l,t)\in\mathbb{R}^{N_{\mathrm{ch}}\times N_{\mathrm{fr}}} ; Filter scales \{\sigma_{k}\}_{k=1}^{K} ; SNR threshold T_{SNR} Output: Peak channel index l^{*}(t) and best scale \sigma^{*}(t) for each time frame t foreach time frame t do foreach scale \sigma_{k} do Compute matched filter response: r_{k}(l,t)=(\dot{\varepsilon}*(-\psi^{\prime}_{\sigma_{k}}))(l,t) ; Determine optimal scale: k^{*}=\arg\max_{k}\max_{l}|r_{k}(l,t)| ; Record peak channel: l^{*}(t)=\arg\max_{l}|r_{k^{*}}(l,t)| ; Record best scale: \sigma^{*}(t)=\sigma_{k^{*}} ; Discard records with \mathrm{SNR}(r_{k}(l,t))