Characterizing Quantum Error Correction Performance of Radiation-induced Errors P. G. Baity, A. K. Nayak, L. R. Varshney, N. Jeon, B.-J. Yoon, P. J. Love, A. Hoisie Abstract Radiation impacts are a current challenge with computing on superconducting-based quantum devices because they can lead to widespread correlated errors across the device. Such errors can be problematic for quantum error correction (QEC) codes, which are generally designed to correct independent errors. To address this, we have developed a computational model to simulate the effects of radiation impacts on QEC performance. This is achieved by building from recently developed models of quasiparticle density, mapping radiation-induced qubit error rates onto a quantum error channel and simulation of a simple surface code. We also provide a performance metric to quantify the resilience of a QEC code to radiation impacts. Additionally, we sweep various parameters of chip design to test mitigation strategies for improved QEC performance. Our model approach is holistic, allowing for modular performance testing of error mitigation strategies and chip and code designs. I Introduction The current generation of superconducting quantum processors are plagued by several sources of physical qubit noise Krantz et al. 2019 . While many studies focus on the ubiquitous two-level system noise Müller et al. 2019 ; McRae et al. 2020 or electronic noise Chow et al. 2010 ; Hyyppä et al. 2024 , recent works Vepsäläinen et al. 2020 ; Wilen et al. 2021 ; Iaia et al. 2022 ; Harrington et al. 2025 ; Larson et al. 2025 have shown that radiation impacts on quantum devices cause distinctive, correlated noise profiles in which data on neighboring qubits simultaneously decay due to the generation of superconducting quasiparticles (QPs). This spatially correlated noise is especially problematic for quantum error correction (QEC), where codes typically are designed to handle only a finite number of single-qubit errors Wilen et al. 2021 ; Fowler et al. 2012 ; Cleland 2022 . Several mitigation strategies, such as phonon downconversion Martinis 2021 ; Iaia et al. 2022 and superconducting gap engineering McEwen et al. 2024 , have been developed to address QP errors. Recently, a Monte-Carlo-based approach was created Yelton et al. 2024 to model the effects of such mitigation strategies by simulating the QP density evolution following the impact of a \gamma ray or cosmic ray \mu^{-} . However, to date, this model has only been applied to test devices for verification purposes. General studies of surface codes assume a uniform or average error rate p_{e} for individual qubits with logical error probability p_{L}\propto p_{e}^{(d+1)/2} , where d is the distance of the code Dennis et al. 2002 ; Fowler et al. 2012 ; Cleland 2022 ; Acharya et al. 2025 . However, in the context of radiation impacts, error rates are expected to be both spatially and temporally correlated across the sequential QEC rounds Wilen et al. 2021 . Codes, such as surface codes that detect the parity among nearest neighbors, may be highly susceptible to uncorrectable errors or miscorrection. Studies on the failure mechanisms within running QEC codes during radiation impact events remain limited Xu et al. 2022 ; Sane et al. 2023 ; Vallero et al. 2024 , and qubit error rates are approximated using phenomenological noise models with radial symmetry from the impact site. In practice, however, a quantitative model of the noise may provide more accurate predictions in the context of phonon caustics Kelsey et al. 2023 ; Hernandez et al. 2025 , material dependence Place et al. 2021 ; Murray 2021 , or the implementation of physical error mitigation strategies Martinis 2021 ; Iaia et al. 2022 . To more completely elucidate QEC failure mechanisms in the context of radiation impacts, we develop and introduce a new computational model for QEC efficacy of radiation-induced errors. This model takes advantage of recent developments in the modeling of qubit error rates following radiation impacts Yelton et al. 2024 . We demonstrate the model by characterizing the efficacy of phonon downconversion Iaia et al. 2022 when implemented on a 17-qubit, transmon-based quantum processing unit (QPU) performing a [[9,1,3]] surface code. II Radiation Impact Model Our approach uses a combination of computational methods to model the failure rates for QEC. The physical model for radiation impacts and QP poisoning of superconducting devices is derived from the results of Yelton et al. Yelton et al. 2024 , which uses the Monte-Carlo-based simulation packages Geant4 Agostinelli et al. 2003 ; Allison et al. 2006 ; Allison et al. 2016 and G4CMP Kelsey et al. 2023 for high-energy and condensed matter particle tracking, respectively. These packages can be used together to model the generation of \mathrm{e}^{-} ​/ \mathrm{h}^{+} pairs, phonons, and QPs in planar superconducting devices. The output of these simulations is the generation term for superconducting QPs, g_{qp}(t) , which is used to derive the time evolution of the normalized QP density x_{qp} (see Ref. Yelton et al. 2024 and App. A ) using the time-dependent ordinary differential equation (ODE) for QP recombination and decay Rothwarf and Taylor 1967 ; Wang et al. 2014 ; Yelton et al. 2024 . Figure 1 (a) shows an example x_{qp}(t) curve set for a 17-qubit QPU following a muon strike. An increase in x_{qp} decreases the relaxation times of the transmons linearly Catelani et al. 2012 ; Wang et al. 2014 ; Iaia et al. 2022 ; Yelton et al. 2024 , and the dynamical changes to the relaxation time T_{1}(x_{qp}) can be calculated following an event as \frac{1}{T_{1}}=\frac{1}{T_{1}^{b}}+\frac{x_{qp}}{\pi}\sqrt{\frac{2\omega_{01}\Delta_{Al}}{\hbar}}, (1) where T_{1}^{b} is the baseline relaxation time, \omega_{01} is the qubit transition frequency, and \Delta_{Al} is the superconducting gap of the Al-based Josephson junction. The qubit parameters are uniform for all 17 transmons and are listed in Table 1 . Moreover, while previous works have focused primarily on the relaxation time T_{1} , the quantum noise channel used in Section III also requires the dephasing rate \Gamma_{\phi} or equivalently T_{2} . The x_{qp} -dependence for \Gamma_{\phi} is derived in Appendix B and depends on the transmon capacitive energy E_{C} : \Gamma_{\phi}(x_{qp})=\Gamma_{\phi}^{b}+\frac{E_{C}x_{qp}^{2}}{2\pi^{2}}e^{\tfrac{1}{2}W_{0}\!\bigl(4\pi/x_{qp}^{2}\bigr)}. (2) Here, \Gamma_{\phi}^{b} is the baseline dephasing rate, and W_{0}(\cdot) is the principal branch of the Lambert function (i.e., the product logarithm function). However, as described in Catelani et al. 2012 , this dephasing rate is small compared to the relaxation rate. As a result, our analysis of QEC performance focuses on bitflip errors for Z -basis measurements and data correction. Transmon Parameters \omega_{01}/2\pi 5.000\text{\,}\mathrm{GHz} E_{C}/h 0.400\text{\,}\mathrm{GHz} E_{J}/h 9.234\text{\,}\mathrm{GHz} E_{J}/E_{C} 23 T_{1}^{b} 100\text{\,}\mathrm{\SIUnitSymbolMicro s} T_{2}^{b} 200\text{\,}\mathrm{\SIUnitSymbolMicro s} Gate Times CX 40 ns H 30 ns Readout 140 ns Table 1: Transmon and gate parameters assumed in the simulation. These values are assigned to every qubit in the circuit. T_{1}^{b} and T_{2}^{b} are the baseline relaxation times for the qubits prior to any quasiparticle generation. E_{C} and E_{J} are the transmon capacitive and Josephson energies, respectively, and \omega_{01} is the transition frequency. (a) (a) (b) (b) Figure 1: (a) The normalized quasiparticle density x_{qp} for a 17-qubit QPU following a muon strike. These curves are generated using the Geant4/G4CMP simulation and ODE as described in Ref. Yelton et al. 2024 and App. A . The corresponding QPU design and muon strike location are shown in the inset. The device is modeled with Nb/Al superconducting material platform fabricated on 10\times 10\times 0.525 mm 3 Si die. No Cu is modeled on the flipside of the chip. (inset) The QPU layout for the rotated [[9,1,3]]] surface code: 17 qubits are arranged into nine data (red), four X -parity (blue), and four Z -parity (green) ancilla qubits for syndrome readout. The stabilizer plaquettes are shaded as blue and green squares and triangles to help visualize which qubits are checked by which stabilizer measurements. (b) The circuit diagram for the stabilizer rounds consisting of Hadamard (H) and controlled not (CX) gates. The qubit registers are labeled in accordance to those in (a). At the end of the stabilizer rounds, the syndromes are measured out to the classical register. The syndrome measurement projects the data into a quiescent state Cleland 2022 , which can be saved for future use before the data readout. III Surface Code and Error Model While Geant4 and G4CMP simulations provide the necessary framework to model the physical response for a \mu^{-} or \gamma ray strike on the QPU, the QEC code is simulated in either Qiskit and the relevant subpackages Qiskit-Aer and Qiskit-QEC Javadi-Abhari et al. 2024 or Stim Gidney 2021 . Figure 1 shows the stabilizer circuit and qubit layout for the example [[9,1,3]] rotated surface code circuit with nine data qubits and eight ancilla qubits. In the surface code operation, this stabilizer circuit and corresponding syndrome measurements are repeated in consecutive rounds or cycles Cleland 2022 ; Acharya et al. 2025 , and errors are decoded Riesebos et al. 2017 ; Chamberland et al. 2018 ; Higgott 2022 . To model the dynamical qubit error rates during the simulation, the noise model is applied in a quasi-equilibrium approximation. T_{1} and T_{2} are evaluated with time step resolution \Delta t equal to the surface code cycle time \tau_{c} , and a per cycle noise model is constructed corresponding to the instantaneous values of T_{1} and T_{2} . This noise model is then applied to each gate within the cycle. In Qiskit, this is accomplished by passing the state vector between a series of artificial backends, each with their own noise model. In the demonstrated surface code, \Delta t=\tau_{c}=1 \mu s approximately agrees with recent implementation Acharya et al. 2025 of the surface code. Because T_{1} recovery occurs over the order of \gtrsim 300 \mu s, the dynamics are generally slow enough to accommodate the quasi-equilibrium condition for each cycle. The cycle-dependent noise model itself is generated using a generalized amplitude damping (GAD) quantum error channel for thermal relaxation and dephasing (see Qiskit-Aer documentation Qiskit Development Team 2025 ). The Choi representation for this channel is: \Lambda=\begin{pmatrix}1-p_{1}(1-e^{-t_{g}/T_{1}})&0&0&e^{-t_{g}/T_{2}}\\ 0&p_{1}(1-e^{-t_{g}/T_{1}})&0&0\\ 0&0&p_{0}(1-e^{-t_{g}/T_{1}})&0\\ e^{-t_{g}/T_{2}}&0&0&1-p_{0}(1-e^{-t_{g}/T_{1}})\end{pmatrix}, where p_{0} and p_{1} are the thermal populations of \ket{0} and \ket{1} , respectively, and t_{g} is the gate time. Typically, p_{0} and p_{1} are calculated using Maxwell-Boltzmann statistics Jin et al. 2015 , where for sufficiently cold systems, p_{0}\approx 1 and p_{1}\approx 0 . In the context of radiation impacts, the system may be considered in terms of a quasi-equilibrium effective temperature T_{eff} with increased excited state populations (see App. A ). However, experiments McEwen et al. 2022 have shown an asymmetry in rates of \ket{1}\rightarrow\ket{0} and \ket{0}\rightarrow\ket{1} during radiation impacts, indicating an atypical thermal response. Although QPs are generated with densities corresponding to higher temperatures ( T_{eff}(x_{qp})\sim 250 mK) in quasi-equilibrium, the lack of observed \ket{0}\rightarrow\ket{1} rates indicates this effective temperature does not control qubit state populations. Therefore, setting p_{1}=0 and p_{0}=1 captures both the suppression of thermal excitations due to refrigeration and the idiosyncratic asymmetry of QP-induced errors. However, this asymmetry is not a dominant factor in the logical error rate of the surface code. Regardless, this noise channel is applied to single- and two-qubit gates in the form of Kraus operators K_{i} , which in a density-operator formalism act on the density matrix ( \rho ): \rho^{\prime}=\sum_{i}{K_{i}U_{g}\rho U_{g}^{\dagger}K_{i}^{\dagger}} , where U_{g} is the unitary operator for the selected qubit gate. Gate times and the modeled transmon properties are listed in Table 1 . In addition to the Qiskit-based simulation, the same circuit is implemented in Stim Gidney 2021 to achieve a computational speedup. In this case, the noise channel is simplified to a Pauli twirled generalized amplitude damping (PTGAD) channel. Unlike the asymmetric GAD channel, the PTGAD channel has no dependence on p_{0} or p_{1} and is therefore rate-symmetric. The Pauli coefficients are expressed as: \displaystyle P_{X} \displaystyle=P_{Y}=\frac{1}{4}\bigl(1-e^{-t_{g}/T_{1}}\bigr) (3) \displaystyle P_{Z} \displaystyle=\frac{1}{2}\bigl(1-e^{-t_{g}/T_{2}}\bigr)-\frac{1}{4}\bigl(1-e^{-t_{g}/T_{1}}\bigr) (4) \displaystyle P_{I} \displaystyle=1-P_{X}-P_{Y}-P_{Z}. (5) Figure 2 compares the Qiskit- and Stim-based simulations. To adequately compare both simulation methods, the readout bits are decoded and corrected using an identical, PyMatching-built minimum weight perfect matching (MWPM) decoder Higgott 2022 . Details about the decoder construction are provided in Appendix C . Results for the two different simulation platforms are similar. However, Stim-based simulations lead to a statistically insignificant increase to the baseline logical error rates and noisier p_{L} curves. As both Qiskit and Stim simulations produce nearly identical results, unless otherwise noted, we proceed with Stim-based simulations using the symmetric noise model. To quantify the logical error rates, a series of stabilizer circuit rounds is executed using the cycle-evolving noise model. To start, a singular stabilizer round with syndrome measurements is first executed without the noise model, resulting in a pure quiescent state Cleland 2022 with known syndromes. From this point, two protocols can be established. In Protocol I, the cycles are chained together, so the measured data can be decoded using the full history of syndromes. In Qiskit, this is accomplished by saving the state vector before data measurement then initializing this state vector at the beginning of the next cycle on the updated artificial backend. In Stim, Protocol I is intrinsically built by appending detector rounds together. However, measuring the full logical error rate evolution of N_{c} cycles using this method requires the simulation of N_{c}(N_{c}+1)/2 cycles. Therefore, in both cases, Protocol I leads to computationally more demanding simulations. On the other hand, p_{L} at the n th cycle can also be calculated Acharya et al. 2025 from the error rate per cycle \varepsilon_{i} accumulated in the preceding cycles using the relationship p_{L}=\frac{1}{2}(1-\prod_{i}^{n}(1-2\varepsilon_{i})). (6) Protocol II employs this relationship to model p_{L} using error rates \varepsilon_{i} measured from individual, unlinked stabilizer rounds where the state is self contained within the round and unassociated to the states in neighboring rounds. In this case, the noise-free quiescent state with known syndromes is initialized, the noisy circuit is performed once, and the resulting data are then decoded to measure \varepsilon_{i} . This method saves time by simulating only N_{c} cycles and produces curves qualitatively similar to Protocol I. However, as shown in Figure 2 , Protocol II over-estimates error rates compared to both the state-chained simulations and even the uncorrected data. Hence, we proceed using Protocol I despite it leading to longer simulation times. (a) (a) (b) (b) Figure 2: A comparison of the surface code simulation results using the Python packages (a) Qiskit and (b) Stim. The Qiskit simulation uses the GAD channel of Eq. III , while the Stim simulation uses the PTGAD channel for respective noise models. In both cases, T_{1}=100 \mu s and T_{2}=200 \mu s for each qubit, and the circuit is sampled 4096 times. In the Qiskit case, the syndrome measurement cycles are chained together by passing the state between sequential rounds. For the Uncorrected curves, no error correction is applied, and p_{L} is measured from the data parity. For Corrected curves, the historical syndrome data are decoded by a repetition MWPM decoder (see App. C ), and appropriate bitflips are applied to the Z -basis data post measurement. For comparison, the individual rounds are also modeled with single-shot circuit execution, decoding, and correction to calculate the logical error per round \varepsilon_{i} . In this latter scenario, states have no dependence on neighboring cycles. The corresponding p_{L}(\varepsilon_{i}) can be calculated using Eq. 6 . Notably, this method overestimates the error compared to state-chained simulations. IV Results To briefly summarize the framework for the model detailed in the previous sections, the surface code response to a radiation impact is implemented using two models. The first model, built principally using Geant4 and G4CMP, simulates the generation of QPs following a \mu^{-} or \gamma -ray strike. The dynamical evolutions to the T_{1} and T_{2} times due to phonon propagation are calculated for each qubit with a time resolution \Delta t=1 \mu s. Each qubit is provided a baseline T_{1}^{b}=100 \mu s and T_{2}^{b}=200 \mu s (i.e., \Gamma_{\phi} =0), which is modified per the descriptions in Appendix B . These T_{1} and T_{2} times are used to calculate the PTGAD noise channel for each gate operation within the surface code operation cycles with duration t_{c}=\Delta t . Because we focus on the effect of radiation impacts, other sources of noise (e.g., electrical or two-level systems (TLS)) are omitted. The summary of transmon and gate times is listed in Table 1 . The surface code is then modeled in Stim, tracking the syndrome history across sequential cycles with a data measurement in the Z -basis in the final cycle. This syndrome history is decoded using the repetition MWPM decoder built from a matching matrix (see App. C ). Once corrections are applied to the data, the data parity is used to measure the logical state, and statistics are collected to measure the evolution of the logical error probability following a radiation impact. Figure 3 (a) shows some example results of the model. In these examples, the muon strike occurs at the location and chip design shown in Figure 1 (a). The evolution is modeled as if the muon strikes after one noisy cycle, and N_{c}^{max}=1500 total cycles are modeled. The baseline logical error probability calculated without the muon ( p_{L}(\bar{\mu}) ) has a qualitatively similar evolution to those observed in experimental implementations Acharya et al. 2025 , although with a much slower error rate due to the ideal circumstances built into the model. In contrast, the logical error probability with the muon ( p_{L}(\mu) ) demonstrates a near immediate jump to a 50% logical error rate, indicating a complete loss of logical state control. This behavior can be attributed to the widespread propagation of phonons across the chip Yelton et al. 2024 . In addition to the mitigation-free chip design, we can also model the effects of potential mitigation strategies on the surface code operation. As in Yelton et al. 2024 , devices can be modeled with Cu on the backside of the Si die. In this case, Cu rapidly downconverts phonons Iaia et al. 2022 to energies below 2\Delta_{Al} , the minimum energy required to generate QPs in the qubits’ Josephson junctions. Figure 3 (a) also shows the effect of Cu downconvertion on surface code performance following identical muon strikes. As metal thickness increases, the jump size at the muon strike time decreases. Interestingly, unlike the case without mitigation, a brief recovery period is observed when phonon downconversion is present, and p_{L}(\mu) decreases down to a dip before gradually increasing again. We attribute this behavior to two related effects. First, the effect of phonon downconversion limits the generation of QPs on qubits far from the strike location, and, second, the recovery of the logical state due to correction as syndrome reliability recovers. While qubits have a large burst in error rates, as downconversion proceeds, syndrome measurements become reliable enough to relay some information to the decoder. As syndromes are repeated, this information improves the decoder’s ability to correct some of the initial burst errors. Hence, the logical error rate reaches a local minimum before the expected low-frequency signal degradation becomes dominant again. As Cu thickness increases and phonon downconversion becomes more efficient, the recovery dip deepens as more reliable syndrome information is messaged to the decoder within each cycle. The behavior of p_{L}(\mu) (shown in Fig. 3 (a)) leads to a natural metric to measure the efficacy of both QEC codes and mitigation strategies in either correcting or preventing radiation-induced errors. In this case, we define a performance gap \zeta_{c}=\langle p_{L}(\mu)-p_{L}(\bar{\mu})\rangle_{c}, (7) which is the cycle average of the difference in logical error rate between radiated and non-radiated test cases. This metric is general and can be applied regardless of the QEC code structure (i.e., arbitrary code distance, homotopy, or decoder), source of radiation ( \gamma , \mu , \alpha , etc.), or physical mitigation strategy (downconversion, gap engineering, Si trenching). The Figure 3 (b) inset shows how this metric is defined. Figure 3 (b) mainly demonstrates how \zeta_{c} can be used to measure the efficacy of mitigation strategies and chip design. Here, Cu thickness and qubit-qubit separation are tuned. In the case of qubit-qubit separation, the qubit arrangement is identical to that shown in Figure 1 (a) but scaled from 1 mm nearest neighbor distance to 2 mm and 4 mm. The chip width is scaled proportionally to accommodate the circuit’s increased footprint over the Si surface. For each data point, the average \zeta_{c} is calculated for 64 muon strikes through the device surface distributed by a two-dimensional Sobol sequence. While chips without any phonon downcoversion show similar \zeta_{c} regardless of qubit separation, the introduction of Cu rapidly reduces \zeta_{c} . However, qubit-qubit distance must be increased to fully recover the non-radiated performance. \begin{overpic}[Cu_dependence_d3_10mm.png] \put(0.0,70.0){(a)} \end{overpic} (a) \begin{overpic}[Cu_dependence_d3.png] \put(0.0,70.0){(b)} \end{overpic} (b) Figure 3: (a) The [[9,1,3]] surface code logical error probability p_{L} following a muon strike. The simulation consists of the 10\times 10 -mm 2 chip configuration shown in Figure 1 (a) with corresponding muon strike location. Average T_{1} and T_{2} values are calculated from a 100 muon ensemble as described in Appendix D . To test the efficacy of phonon downconversion, the chip is modeled with Cu of varying thicknesses covering the underside, such as in Iaia et al. 2022 and Yelton et al. 2024 . (b) The performance gap as a function of Cu thickness and qubit spacing. To sweep qubit spacing, the diagram of Figure 1 (a) is scaled by either a factor of 2 or 4. The chip size is increased to 20\times 20 mm 2 and 40\times 40 mm 2 , while the qubit nearest neighbor spacing is increased from 1 mm to 2 mm and 4 mm. The performance gap \zeta_{c} is measured over an average of 64 muon strikes normal to the chip surface. (inset) Demonstration of how the performance gap is calculated (shaded region). The difference between p_{L}(\mu) and p_{L}(\bar{\mu}) is integrated then normalized by the total number of simulated cycles ( N_{c}\approx 1500 ). V Discussion Although our model captures the long-range component of correlated errors from QP generation, there are several avenues for model improvement. Additional physical models for TLS restructuring Wilen et al. 2021 ; Thorbeck et al. 2023 ; Harrington et al. 2025 may be necessary to fully capture the correlated error dynamics closest to the injection site. Furthermore, per Section III , the thermal populations are set as p_{0}=1 and p_{1}=0 in the GAD noise channel. This better models the QP dynamics by reflecting both the thermal statistics of a sufficiently cold device, as well as the asymmetry of QP-induced error rates. As explained in McEwen et al. 2022 , this rate asymmetry occurs due to the fast cooling of QPs to the superconducting gap edge so that they can only absorb energy from the qubit. Under this explanation, the noise model may need adjustment in the case of constant phonon injection Iaia et al. 2022 or steady-state phonon generation from the refrigerator pulse-tube Yelton et al. 2025 . In these scenarios, the continuous generation of hot QPs may modify this rate asymmetry, leading to increased occupation of excited states more in line with Maxwell-Boltzmann statistics Jin et al. 2015 as measured by T_{eff}(x_{qp}) . Given the elevated T_{eff}(x_{qp})\sim 250 mK observed in our simulations, these scenarios may also lead to noise leakage with occupancy of higher energy states ( \geq\ket{2} ), which is not captured in our model. Additional experiments examining rate symmetry with steady-state phonon injection may close this knowledge gap. Simulations to test the efficacy of phonon downconversion as a mitigation strategy for radiation-induced errors demonstrate that additional limitations on qubit-packing density are required to fully suppress errors. While this method reduces error rates substantially (i.e., \zeta_{c}\to 0 ) compared to devices with no mitigation strategy, qubit separation distance must be increased to fully suppress the effects of correlated errors. Furthermore, the majority of the benefit occurs with only a thin layer of Cu, while increasing the thickness of the downconversion metal provides only diminishing returns in performance. In other words, increasing the downconversion metal thickness does not allow for tighter packing of qubits on the chip. However, this also means that a thin layer ( \lesssim 1 \mu m) of a normal metal or low-gap superconductor Henriques et al. 2019 is likely sufficient to gain most of the benefit from this strategy. For example, in the 40-mm chip design, 500 nm (200 nm) of Cu is expected to be only 2 \% (8 \% ) less effective than 13 \mu m of Cu and well within the uncertainty range for the sampled muon ensemble (see App. D for details). In this light, the implementation of phonon downconverting metal films is still compatible with the standard CMOS (Complementary Metal Oxide Semiconductor) fabrication techniques as the electroplating method used in Iaia et al. 2022 to create thick films of Cu may be unnecessary. Instead, such films can be sufficiently thin that Ar-plasma sputtering alone can be used. Furthermore, as higher-distance codes are generally more resilient to error, the optimal qubit-packing density to withstand radiation-induced errors may itself increase with the code distance. A more detailed study with experimental validation may be necessary to determine this dependence. When additional error mitigation strategies are present, the surface code test case demonstrates a surprising recovery dip following the radiation impact. This behavior implies that limited degrees of correlated errors may still be correctable for standard surface code and decoder setups. Other decoders, such as custom machine learning decoders Acharya et al. 2025 trained on simulated data, may prove viable for the correction of radiation-induced errors. Likewise, optimization methods applied toward minimizing \zeta_{c} may prove beneficial for improving architecture and code designs. VI Conclusion We have established a method for modeling QEC performance in the presence of radiation impacts on a superconducting quantum processor. Although only a simple 17-qubit [[9,1,3]] surface code is demonstrated, this method is generalizable to arbitrary architecture or code structures. Additionally, we have confirmed that a Pauli-twirled GAD quantum channel can adequately model the error rates during a radiation impact despite the differences in error rate symmetry between GAD and PTGAD channels. Lastly, we have introduced a new metric, \zeta_{c} , to measure the performance of QEC codes and physical error mitigation strategies for radiation-induced errors. The usefulness of \zeta_{c} has been demonstrated for the mitigation test case of phonon downconversion using flipside Cu. In this regard, machine-learning–driven optimization and active learning methods applied toward reducing \zeta_{c} can be used to efficiently search the enormous design space of quantum processors Alexander et al. 2023 . By leveraging uncertainty-aware surrogate models Qian et al. 2023 , this approach may actively steer the expensive physical simulations established in this manuscript toward the most informative design candidates and enable the discovery of architectures with improved resilience to radiation-induced errors. Acknowledgements. This work was supported by the Laboratory for Physical Sciences through Strategic Partnership Project No. EAOC0206928. Brookhaven National Laboratory is supported by the U.S. Department of Energy’s Office of Science under Contract No. DE-SC0012704. This work was also supported by resources provided by the Scientific Computing and Data Facilities (SCDF), a component of the Computing and Data Sciences Directorate at Brookhaven National Laboratory. We also thank C. Plata for editorial review of the manuscript. AI Disclaimer: Both ChatGPT and Claude Sonnet were used to suggest code modifications to human-written codes for the purposes of troubleshooting and error handling. Adopted code changes were first validated by the authors. The manuscript text, figures, and contents were written and generated solely by the authors themselves. Appendix A Quasiparticle Model As discussed in the main text, we adapt the recent framework developed by Yelton et al. Yelton et al. 2024 to model the quasiparticle (QP) density ( n_{qp} ) evolution after a \mu^{-} or \gamma ray impact. This model is based on a Geant4 and G4CMP Monte Carlo simulation, whose output is used to evaluate the generation term g_{qp}(t) for QPs in the ordinary differential equation (ODE): \frac{dn_{qp}}{dt}=-rn_{qp}^{2}-sn_{qp}+g_{qp}(t). (8) Here, r is the QP recombination rate, and s is the decay rate. While these rates can vary from qubit to qubit in practical devices, we choose nominal values of s=0.05 \mu s -1 and r=25\times 10^{-6} \mu s -2 for all qubits, consistent with the range of values found in Yelton et al. 2024 . The device itself is modeled as a square Si die with dimensions 10\times 10\times 0.525 mm 3 . The die’s surface is blanketed with a 75-nm thick Nb film. Transmon junctions are modeled as 10\times 10\times 0.1 \mu m 3 Al patches distributed across the die. For the surface code arrangement used in the main text, there is a \sim 1 mm pitch between qubit junctions. Radiation impacts are modeled as ionization ( \mu^{-} ) or Compton scattering ( \gamma ray) processes in the Si for the generation of \mathrm{e}^{-} ​/ \mathrm{h}^{+} pairs. These pairs then participate in the Neganov-Trofimov-Luke (NTL) process Kelsey et al. 2023 to generate phonons. This method differs from Yelton et al. 2024 , which directly injects \mathrm{e}^{-} ​/ \mathrm{h}^{+} pairs to model \gamma ray impacts. Modeling the full ionization process considers the transience of muons during the ionization process and pair generation. Moreover, the Compton scattering event for \gamma rays also creates recoil electrons Norcini et al. 2022 , which themselves further ionize \mathrm{e}^{-} ​/ \mathrm{h}^{+} pairs at they traverse the Si. In such scenarios, a purely stationary generation point for \mathrm{e}^{-} ​/ \mathrm{h}^{+} pairs may not fully characterize the dynamics of qubit error generation, especially when mitigation strategies limit phonon propagation and not muon or recoil-electron propagation. Computationally evaluating the ODE provides the normalized QP density x_{qp}(t)=n_{qp}(t)/n_{cp} , where n_{cp} is the density of Cooper pairs. To keep the model internally consistent, we adjust n_{cp} to reflect the modified Al gap energy \Delta_{Al}=191\pm 1 \mu eV used in Yelton et al. 2024 . As defined in Catelani et al. 2011 , n_{cp}=2g_{1}(0)\Delta , where g_{1}(0) , is the single electron density of states at the Fermi surface. Using the free electron gas model from Kittel 2005 , g_{1}(E)=\frac{(2m_{e}^{3}(E-E_{con}))^{1/2}}{2\pi^{2}\hbar^{3}} , a conduction band energy of E_{con}=11.3\pm 0.4 eV (averaging the range of values in Kittel 2005 ; Levinson et al. 1983 ), and \Delta_{Al} , we find n_{cp}=(4.38\pm 0.09)\times 10^{6} cm -3 , a \sim 10\% increase from the values used in Wang et al. 2014 ; Yelton et al. 2024 . This increase stems from the increased \Delta_{Al} value. However, as noted in Yelton et al. 2024 , \Delta_{Al} is thickness dependent and will likely change with design and fabrication details. Therefore, n_{cp} should also be reevaluated depending on the system. Appendix B Modeling Amplitude and Dephasing Errors Because the surface code depends on both X - and Z -parity checks, dephasing error rates due to QP generation need to be considered. To model dephasing rates, we use the formulas provided by Catelani et al. 2012 for transmon qubits. Noting these equations are derived in a quasi-equilibrium approximation with an effective temperature T_{eff} describing the normalized QP density x_{qp} , the equilibrium description x_{qp}=\sqrt{\frac{2\pi k_{B}T_{eff}}{\Delta_{Al}}}e^{-\Delta_{Al}/k_{B}T_{eff}} Barends et al. 2011 can be used to translate the simulation-derived x_{qp} into \Gamma_{1} and \Gamma_{\phi} . The inverse solution T_{eff}(x_{qp}) can be expressed using the product logarithm, which corresponds to the principle ( k=0 ) branch of the Lambert W_{k}(\cdot) function: T_{eff}=\frac{2\Delta_{Al}}{k_{B}W_{0}(4\pi/x_{qp}^{2})}. (9) Changes to the qubit relaxation rate can then be expressed in terms of x_{qp} as \begin{split}\Delta\Gamma_{1}&=2\sqrt{\frac{\omega_{01}k_{B}T_{eff}}{\pi\hbar}}\,e^{-\Delta_{Al}/k_{B}T_{eff}}\\[4.0pt] &=2\sqrt{\frac{2\omega_{01}\Delta_{Al}}{\pi\hbar W_{0}\!\bigl(4\pi/x_{qp}^{2}\bigr)}}\,e^{-\tfrac{1}{2}\,W_{0}\!\bigl(4\pi/x_{qp}^{2}\bigr)}\\[4.0pt] &=\frac{x_{qp}}{\pi}\sqrt{2\omega_{01}\Delta_{Al}/\hbar},\end{split} (10) using the definition of the product logarithm W_{0}(z)e^{W_{0}(z)}=z to derive the linear dependence on x_{qp} , which is used in Wang et al. 2014 ; Iaia et al. 2022 . This same method can be used to find the changes to the dephasing rate: \begin{split}\Delta\Gamma_{\phi}&=\frac{E_{C}T_{eff}}{\pi\Delta_{Al}}e^{-\Delta_{Al}/T_{eff}}\\[4.0pt] &=\frac{E_{C}x_{qp}^{2}}{2\pi^{2}}e^{\tfrac{1}{2}W_{0}\!\bigl(4\pi/x_{qp}^{2}\bigr)}.\end{split} (11) Thus, the QP-induced dephasing rate can be expressed in terms of the x_{qp} . T_{2} can then be calculated as 1/T_{2}=1/2T_{1}+\Delta\Gamma_{\phi}+\Gamma_{\phi}^{b} , where \Gamma_{\phi}^{b} is the baseline dephasing rate, which is assumed negligible (i.e., \Gamma_{\phi}^{b}=0 ). As noted in Catelani et al. 2012 , the dephasing rate contribution from QPs is expected to be much smaller than the relaxation rate. This is verified by the numerical evaluation of 2T_{1}\Gamma_{\phi} , shown in Figure 4 . Nevertheless, for larger E_{C} values, the rate of dephasing errors may become noticeable at the higher levels of x_{qp} achieved following radiation impact events. Figure 4: 2T_{1}\Gamma_{\phi} measures the comparison between the dephasing and relaxation rates as a function of x_{qp} . The minimum and maximum range of x_{qp} covers the ranges observed in the simulation data. These values have been calculated using the transmon parameters listed in Table 1 . Appendix C Error Decoding To determine the logical error probability, errors are decoded using a Minimum Weight Perfect Matching decoder built with PyMatching Higgott 2022 . Bit errors are corrected after Z -basis data measurement. The matching matrix to decode the ZZZZ syndromes is determined by the circuit deMarti iOlius et al. 2024 shown in Figure 1 (b): H_{Z}=\begin{bmatrix}1&0&0&1&0&0&0&0&0\\ 0&1&1&0&1&1&0&0&0\\ 0&0&0&1&1&0&1&1&0\\ 0&0&0&0&0&1&0&0&1\end{bmatrix}. To avoid notation confusion, the subscript here denotes the parity being checked ( Z -parity) rather than the type of error being corrected ( X -error). This matching matrix is then used by PyMatching to construct the syndrome graph necessary to decode errors from syndrome measurements. While each cycle i provides a set of ZZZZ syndrome measurements S_{i}^{Z} , the decoder graph is constructed with repetition, and the syndrome differences D_{i}^{Z} between neighboring cycles D_{i}^{Z}=S_{i-1}^{Z}\oplus S_{i}^{Z} (12) are the detectors for errors and provided to the decoder instead of the raw syndrome data. In this case, the first noisy cycle ( i=0 ) is compared to the noise-free syndrome measurement determined when the noise-free quiescent state is first prepared. Like the Z -syndromes, the XXXX syndromes S_{i}^{X} can be decoded in PyMatching using the matching matrix H_{X}=\begin{bmatrix}0&1&1&0&0&0&0&0&0\\ 1&1&0&1&1&0&0&0&0\\ 0&0&0&0&1&1&0&1&1\\ 0&0&0&0&0&0&1&1&0\end{bmatrix}. Once decoded, the operations can be applied to correct phase errors and data measured in the X -basis. Regardless of the type of error, in our study, data bits are corrected after measurement based on the decoded syndromes. Appendix D Analysis of Downconversion Efficacy To generate the data in Figures 3 (a) and 3 (b), we use two different protocols. In Figure 3 (a), the data show the p_{L}(\mu) for one particular \mu^{-} trajectory given varying degrees of Cu thickness. However, to eliminate statistical variations in energy deposition, T_{1} and T_{2} are calculated from the average of 100 strikes at the noted location in the Figure 1 (a) inset. This is done within the Geant4/G4CMP simulation by setting /g4cmp/producePhonons and /g4cmp/producePhonons each to 0.01 and /run/beamOn to 100 Kelsey et al. 2023 . The resulting output file then contains the phonon data for the collective 100 \mu^{-} strikes, which each individually contribute \sim 1\% of the phonons. These phonon data then are used to calculate g_{qp}(t) as described in Yelton et al. 2024 . p_{L} is calculated from the Stim-based simulations with 16,384 runs of the circuit featuring these T_{1} and T_{2} values. Figures 5 (a) and 5 (b) respectively depict the p_{L} for the 20\times 20 mm 2 and 40\times 40 mm 2 devices. In these cases, the geometry – including the muon strike location – is scaled proportionally by a respective factor of two or four. \begin{overpic}[Cu_dependence_d3_20mm.png] \put(-1.0,70.0){(a)} \end{overpic} (a) \begin{overpic}[Cu_dependence_d3_40mm.png] \put(-1.0,70.0){(b)} \end{overpic} (b) Figure 5: Sample p_{L} curves for the (a) 20\times 20 mm 2 and (b) 40\times 40 mm 2 chips. For both devices, the qubits are arranged identically to Figure 1 (a) inset but are scaled by a respective factor of two or four. Likewise, the muon strike location is also scaled from (1.7, 1.7) mm in Figure 1 (a) inset to (3.4, 3.4) mm and (6.4, 6.4) mm. For both cases, as Cu metal thickness increases, the p_{L}(\mu) curves start to approach the p_{L}(\bar{\mu}) curve, and \zeta_{c} approaches zero. For Figure 3 (b), \zeta_{c} is instead averaged for an ensemble of 64 muon strikes wherein the strike location is varied. In this case, the strike locations are generated by a two-dimensional Sobol sequence that is scaled by the chip dimensions. For each muon, phonon statistics are fully sampled, and \zeta_{c} is calculated. The \zeta_{c} values are then averaged for the 64 \mu^{-} ensemble, and the error bars represent the standard deviations. From these data, we conclude that a 500-nm thick film of Cu is only 2\% less effective than a 13- \mu m thick film of Cu for the 40-mm wide chip. This estimation is calculated by comparing the mitigation efficacy of the film downconversion relative to the device without the Cu film. The relative mitigation efficacy is calculated as \delta\zeta_{c}(t_{Cu})=[\zeta_{c}(t_{Cu})-\zeta_{c}(0)]/\zeta_{c}(0), (13) where t_{Cu} is the Cu film thickness. Using this formulation, \delta\zeta_{c}(500~\mathrm{nm})\approx 0.96 , and \delta\zeta_{c}(13~\mu\mathrm{m})\approx 0.98 . Therefore, we conclude the efficiency of the downconversion effect only differs by 2\% between a 500-nm film and a 13- \mu m film. For a slightly thinner \delta\zeta_{c}(200~\mathrm{nm})\approx 0.90 , the difference increases to 8 \% , which is still nominal compared to the standard deviation of \zeta_{c} values calculated from the ensemble of \mu^{-} strikes. Based on this analysis, we conclude that thin films made of Cu or alternative downconversion material may provide only nominally less protection than thicker ones, also depending on the architecture design.