From Equilibrium Multistability to Spatiotemporal Chaos in Channel Flows of Nematic Fluids Rahil N. Valani 1, Sumesh Thampi 1,2, Julia M. Yeomans 1 Abstract We investigate channel-confined, nematic liquid crystals using the Beris-Edwards model of nematohydrodynamics. Using strong homeotropic anchoring at the walls, we find multistability i.e. multiple coexisting states where the uniform nematic state coexists with states having spatially varying scalar nematic order and director fields. When a pressure gradient is applied, flows develop, and the inherent multistability of the system organizes a variety of complex dynamics. For low pressure gradients, steady flows are established, and the director fields that emerge from the multistable states at equilibrium correspond to Bowser and Dowser configurations similar to those reported in experiments. An increasing pressure-gradient destabilizes steady Bowser and Dowser flow states sequentially, leading to unsteady periodic and chaotic regimes featuring cyclical topological transitions, pulsating flows, advecting defects and spatiotemporal chaos. These findings demonstrate that modest variations in the scalar nematic order, as captured by the Beris–Edwards model, can qualitatively modify equilibrium structures and give rise to complex nonequilibrium behaviour in confined nematics—contrasting with the Ericksen-Leslie model, which assumes a constant scalar order parameter. Our key model predictions - multistability, periodically oscillating states and advecting defect-mediated turbulence can be experimentally investigated in pressure-driven channel flows of nematic fluids. keywords Multistability, oscillatory flows, limit cycle, spatiotemporal chaos, nematic channel flows † † affiliation: 1 Rudolf Peierls Centre for Theoretical Physics, Parks Road, University of Oxford, OX1 3PU, United Kingdom 2 Department of Chemical Engineering, Indian Institute of Technology Madras, Chennai-36, India Broken rotational symmetry and orientationally ordered nematic phases are characteristic of fluids composed of anisotropic constituents, for example molecular liquid crystals ( De Gennes & Prost, 1993 ) , colloidal suspensions ( Nagel, 2017 ; Lewis et al., 2014 ) and biological matter ( Doostmohammadi & Ladoux, 2022 ; Maroudas-Sacks et al., 2021 ) . The continuum theory of nematic liquid crystals provides a fundamental framework for describing the dynamics of such complex fluids ( Beris & Edwards, 1994 ; Lettinga et al., 2005 ; Saw et al., 2017 ; Hadjifrangiskou et al., 2025 ) . The microstructure, namely the orientational order of anisotropic constituents can be expressed using a symmetric, traceless tensor, called nematic order-parameter \mathbf{Q} . In two-dimensions, \displaystyle\mathbf{Q}=\begin{pmatrix}Q_{xx}&Q_{xy}\\ Q_{xy}&-\,Q_{xx}\end{pmatrix}\equiv S\!\left(\mathbf{n}\mathbf{n}-\tfrac{1}{2}\mathbf{I}\right), (1) where the scalar S gives the magnitude of nematic ordering and the vector \mathbf{n}=(\cos\theta,\sin\theta) describes the nematic director, the average orientation of the constituents. Thus, S and \theta capture the two degrees of freedom in the nematic order tensor \mathbf{Q} . For isotropic fluids S=0 while for fully ordered nematic fluids S=1 . In thermotropic and lyotropic molecular liquid crystals, temperature and concentration respectively dictate the strength of ordering S . In soft and biological matter, the additional dominant factors that determine S may be the geometry of the constituents, the nonequilibrium forcing and activity ( Frenkel, 2015 ; Olmsted & Goldbart, 1992 ; Santhosh et al., 2020 ) . When driven out of equilibrium either by an external forcing ( Manneville, 1981 ; Dubois-Violette et al., 1971 ; Weiss & Ahlers, 2013 ; Mur et al., 2022 ) or by an internal activity ( Giomi, 2015 ; Alert et al., 2022 ) , nematic fluids display a wide range of steady and unsteady dynamic behaviours. Most theoretical studies that address the dynamics of nematic fluids employ the Ericksen-Leslie equations ( Leslie, 1968 ; Stewart, 2004 ) which assume a uniform field for the magnitude of the order parameter S and only consider variations in the director field. This simplifies the analysis, and their widespread use may be due to the ease of visualisation of the director field in both experiments and computer simulations. Exceptions are studies that address the occurrence and dynamics of topological defects. Topological defects represent singularities in the \mathbf{Q} field; the core of the defect has S=0 and an undefined director orientation. Then a description based on the Beris–Edwards model ( Beris & Edwards, 1994 ) , which incorporates variations in nematic order S is more natural. However, even in the latter theory, in practice, the role of order-parameter variations is often neglected except in the vicinity of the topological defects. Of particular interest is the case of nematic liquid crystals subjected to pressure-driven flows in confined geometries. Early theoretical work was primarily based on Ericksen-Leslie theory ( Leslie, 1987 ) . Further experimental and numerical studies ( Anderson et al., 2015 ; Jewell et al., 2009 ; Batista et al., 2015 ) have demonstrated that elastic and viscous stresses, together with anchoring conditions at the channel walls, can sustain multiple director configurations, giving rise to flow-driven transitions between distinct nematic states in Poiseuille-type flows. These competing states are often explained using free-energy considerations, with transitions occurring as the pressure gradient shifts the balance between anchoring-dominated and flow-aligned director fields. Subsequent extensions using the Beris–Edwards \mathbf{Q} -tensor framework have allowed for systematic treatment of nematic order variations and topological defects, though many analyses continue to neglect order-parameter variations away from defect cores ( Sengupta et al., 2013 ; Aplinc et al., 2016 ; Giomi et al., 2017 ) . Recent theoretical studies have further characterised the solution landscapes and bifurcation structure of confined nematic flows, demonstrating how anchoring and confinement geometry mediate the coexistence of Bowser- and Dowser-like states ( Crespo et al., 2017 ; Paul et al., 2021 ) . Microfluidic experiments using nematic fluids have revealed rich dynamical behaviour consistent with theoretical predictions. Flow-driven transitions between free energy driven and flow-aligned director structures have been observed in nematic channels with strong homeotropic anchoring ( Sengupta et al., 2013 ; Jewell et al., 2009 ) . Recent experiments have demonstrated that careful control of channel geometry, boundary anchoring, and flow rate can stabilise novel intermediate or chiral states ( Čopar et al., 2020 ; İlhan et al., 2025 ) . Classically, Poiseuille-type flows in conjunction with an externally applied magnetic field have been used to manipulate the nematic order and thus determine the rheological properties of nematic liquid crystals ( Olmsted & Goldbart, 1992 ; Kneppe et al., 1981 ) . Together, these studies establish pressure-driven nematic flows as a canonical setting for probing the interplay of rheology, confinement, boundary conditions, and hydrodynamic driving in nematic liquid crystals. However, most analyses have focused on reorienting director fields ( \mathbf{n} ) and their spatial variations, leaving open the role of the magnitude of nematic order ( S ) and its variations in organising the equilibrium and dynamical states in nematic fluids. In this work, we use the Beris-Edwards \mathbf{Q} tensor formalism and demonstrate that even a slight, spatially uniform reduction in the magnitude of nematic order S can fundamentally alter the equilibrium structure of confined nematic fluids. Specifically, we show that such “global melting” of nematic order gives rise to new equilibrium configurations beyond those predicted by the theories that assume a constant nematic order. When the system is driven out of equilibrium through an imposed pressure gradient, these equilibria act as organizing centres for complex dynamics, including bifurcations between competing configurations, oscillatory states, and spatiotemporal chaos. The paper is organized as follows: In section 1 we present the theoretical model. In section 2 we explore the equilibrium state of channel confined nematic fluids (no external forcing). This is followed by analysis of 1D, unidirectional steady and unsteady flows that nematic fluids develop under external forces in sections 3 and 4 , respectively. In section 5 we compare the 1 D results with numerical solutions of the full 2 D equations. We discuss the implications of the results and conclude in section 6 . 1 Theoretical model We consider an incompressible nematic liquid crystal confined in a 2 D planar channel with the coordinate -\infty1 . (We note that in figure 2 (a), we used numerical continuation to follow the steady branches when they are stable, whereas here we solve the PDEs with the initial conditions specified above.) Once all the steady states (gray region) become unstable, we first see oscillatory unsteady behaviour from F\approx 0.0034 to F\approx 0.007 , with chaotic behaviour first emerging beyond F\approx 0.007 , for initial conditions favouring Bowser and Dowser states. By contrast, for random initial conditions, the scattered dots indicate chaos for almost all values of F in the unsteady regime. We also notice from the bifurcation diagram that, if the initial conditions are not random, the system does not permanently maintain chaos for large F in the unsteady regime, and we find alternating regimes of periodic and chaotic behaviours with increasing F ; a feature that is common in bifurcation diagrams of low-dimensional chaotic systems ( Strogatz, 2015 ) . Kymographs of the chaotic dynamics with increasing F beyond F\approx 0.007 are displayed in figure 4 (b)-(d). These show that, although the dynamical behaviour is not entirely periodic, its chaotic nature is weak. There is periodicity on short time scales, with period decreasing with F , and irregularities emerging at longer time scales spanning several periods. This is further evident from the phase space trajectories which show the system traversing a chaotic attractor with some structure, a signature of low-dimensional chaos ( Strogatz, 2015 ) . The almost periodic nature of the chaos is also evident from the bifurcation diagram where, in the chaotic regime, the points are not scattered uniformly but are concentrated near periodic branches. These results provide evidence that, beyond the periodic regime, the system transitions to weak spatiotemporal chaos. Thus, a unidirectional, pressure-driven nematic exhibits a variety of dynamical regimes: steady flows, unsteady periodic flows and spatiotemporal chaos (see Appendix C for bifurcation diagrams for other parameter values). Figure 5: Nematohydrodynamics in 2 D pressure-driven channel flows. (a) Bifurcation diagram analogous to figure 4 (a) for the full 2 D equations of motion ( 2 )–( 4 ). In 2 D flows, multistability is observed between different unsteady dynamical states. For example, at F=0.0024 , (b,e) spatial uniform initial conditions along x corresponding to a Bowser or a Dowser configuration result in periodic states where the whole channel periodically transitions between a Bowser-like and a Dowser-like state. Conversely, if the initial conditions are random, (c,f) then defects are stabilised by advection along the channel. This results in weakly chaotic flow, as the defect dynamics are not entirely periodic. (d,g) At a higher value of F=0.006 , the turbulent flow becomes more prominent through the continuous formation, annihilation and advection of defects. The kymographs in (e)-(g) are shown for at a fixed x=50 . Other parameter values are the same as for figure 4 . 5 Unsteady flows in 2 D channel We now solve the full 2D nematohydrodynamic equations of motion ( 2 )–( 10 ) using a hybrid lattice Boltzmann algorithm ( Marenduzzo et al., 2007 ; Thampi et al., 2016 ) . Analogous to figure 4 (a), we consider pressure-driven 2 D channel flows and create a bifurcation diagram as a function of F , as shown in figure 5 (a). To most easily compare the flow dynamics between 2 D and 1 D, we choose the bifurcation parameters as the peak values in the time series of the nematic free energy calculated at a fixed x location along the channel and integrated across the width y of the channel. The initial conditions are chosen to be the same as those for the bifurcation diagram in figure 4 (a), equation ( 14 ), where we assume the initial orientation field to vary in the y direction but to be constant in the x direction for the Bowser and Dowser favouring initial configurations. For small values of F , we find Bowser and Dowser steady flowing states (grey region) and they undergo the same sequence of instabilities as observed in the 1 D formalism. Further, we ubiquitously find multistability between steady and unsteady states, as well as between different types of unsteady states. In particular, for F\sim 0.0015 (light grey region in figure 5 (a)), the steady states coexist with a dynamic advecting defect state. Initial conditions that favour Bowser or Dowser states indeed lead to Bowser or Dowser steady states with variations in orientation only in the y direction as for the 1 D model. However, if the initial conditions are random, there are many +1/2 and -1/2 topological defects ( Doostmohammadi et al., 2018 ) present in the initial state. Not all of these are able to annihilate with each other and they are advected down the channel by the applied pressure gradient. With increasing F , there is multistability in unsteady states as well. For example, for F=0.0024 , Bowser-like or Dowser-like initial conditions lead to the entire 2 D channel undergoing uniform periodic oscillations between a Bowser and a Dowser state (figure 5 (b)). The kymographs of the velocity field, nematic orientation and nematic order and the phase-space trajectory, which are plotted for a fixed x in figure 5 (e), are similar to those obtained in 1 D (compare figure 3 (a)-(c)). Instead, if the system is started with random initial conditions, we obtain advecting defects, showing signs of weak chaos, as shown by the snapshot in figure 5 (c). The corresponding kymographs are shown in figure 5 (f). Further increases in F lead to more irregular motion of defects i.e. spatiotemporal chaos or topological turbulence, where defects are created and annihilated as they advect down the channel as shown in figure 5 (d), with the corresponding kymographs in figure 5 (g). Note that +1/2 defects are typically found near the centre of the channel whereas -1/2 defects are found near the channel walls.This is consistent with the turbulent state observed in the 1 D model and also with variations in the nematic order observed in steady states for large F (see figure 2 (a)), in both cases the nematic order melts most strongly near the channel centre or walls. Figure 6: Topological defects mediate spatially localized Bowser-Dowser transitions in 2 D pressure-driven nematic flows. (a) Snapshot from a simulation at F=0.014 with random initial conditions showing defects advecting along the channel. The 1 D profiles at different locations along the channel near a defect are shown in panels (b)-(e). A Bowser-Dowser transition is obtained in the 1 D profile as the defect is traversed spatially. The essence of spatiotemporal chaos in 2 D driven nematics that we report here lies in the irregular dynamics of topological defects as they are created, annihilated and advected down the channel due to an applied strong pressure-gradient F . The creation and annihilation of the defects is a reflection of local topological transition between Bowser-like and Dowser-like states. To show this more clearly, we consider an advecting defect state at F=0.0014 obtained from random initial conditions. After initial transients, we obtain advecting pairs of defects as shown in figure 6 (a). Plotting the nematic order and nematic orientation fields at different x positions in the vicinity of the +1/2 defect shows a transition from a Bowser-like to a Dowser-like state (figure 6 (b)-(d)). Hence, topological defects facilitate spatially localized Bowser-Dowser transitions in nematic channel flows. 6 Discussion and conclusions We investigated channel flows of nematic fluids using the Beris–Edwards nematohydrodynamics formalism, comparing a one-dimensional unidirectional model to solutions of the fully two-dimensional differential equations. For a channel confined nematic fluid, at equilibrium (in the absence of an applied pressure gradient), we found coexisting states of the nematic: in addition to the expected solution of uniform \mathbf{Q} , we found that solutions of varying \mathbf{Q} across the width of the channel are also stable. These states are distinct, they have different topology characterized by a difference in winding number of the director when calculated from the bottom wall to the top wall of the channel. When the system is driven out of equilibrium by an imposed pressure gradient, these equilibrium states serve as reference points, about which we observe bifurcations between competing configurations, oscillatory behaviour, and spatiotemporal chaos. At small applied pressure gradients, we obtain a steady Poiseuille-like unidirectional velocity field. Correspondingly, the equilibrium nematic configurations develop distortions. The resulting director fields are the well known Bowser and Dowser states for channel flows of nematic liquid crystals. Increasing pressure gradients lead to the instability of these steady flowing states, resulting in transitions between Bowser and Dowser states. Bowser-to-Dowser transitions have been observed in three-dimensional microfluidic nematic channel flows and are commonly explained in the literature using free-energy arguments. We show instead that both Bowser and Dowser states originate from coexisting, topologically distinct equilibrium configurations, and that transitions between them can be interpreted as dynamical instabilities arising when the steady states lose stability. At larger pressure-gradients, we found that all the steady states cease to exist, and oscillations emerge in both the nematic field and the velocity field. These periodic oscillations correspond to cyclical transitions between Bowser-like and Dowser-like states. The period is very large at the onset of oscillations, and it decreases with increasing pressure gradient. Near the bifurcation, the decrease follows a -1/2 power law consistent with a saddle-node-type bifurcation. Beyond the periodic regime, we find spatiotemporal chaos at large applied pressure gradients. The spatiotemporal chaos organizes itself via continuous creation, annihilation and advection of defects along the channel in an irregular manner. Our findings highlight the need for systematic experimental investigations of confined channel flows in nematic fluids. In the absence of external forcing, equilibrium states exhibiting spatially varying order parameters \mathbf{Q} and boundary-layer structures in the nematic order should be characterized. The multistability observed under applied pressure gradients could be explored through hysteresis experiments, wherein the imposed pressure gradient is varied gradually to look for the coexistence of and switching between Bowser and Dowser states. At higher flow rates, where our analysis predicts oscillatory dynamics and defect-mediated transport, experiments could seek signatures of periodic director oscillations and advecting defect states. Collectively, such measurements would provide direct experimental validation of the dynamical regimes identified here, bridging theoretical predictions and observable behaviour in nematic channel flows. A useful comparison may be drawn between the spatiotemporal chaos reported here and the turbulent regimes of active nematics. Active nematic turbulence is generally regarded as a two-dimensional instability, sustained by self-propelled \pm 1/2 defects. By contrast, the defect-mediated turbulence we report here arises even within our one-dimensional reduction of the Beris–Edwards model, where it manifests through oscillatory instabilities and chaotic dynamics of the order parameter and director field. As a result, the chaotic regimes we observe can already arise in 1D, with 2D simulations enriching this picture through advecting defects. This highlights a key distinction: whereas active nematic turbulence is characterized by two-dimensional defect dynamics, the spatiotemporal chaos of pressure-driven nematics is rooted in confinement-induced instabilities that persist even in reduced-dimensional descriptions. It will be interesting to investigate how these instabilities are modified in three-dimensional geometries and under different confinement conditions. Such extensions would clarify the extent to which the mechanisms identified here are generic features of confined nematic flows. Beyond passive systems, an extension of our analysis to active nematics is especially promising. In this case, the equilibrium state with spatially varying \mathbf{Q} would generate thresholdless active flows due to the presence of director gradients. The competing effects of active turbulence and pressure-driven turbulence may give rise to a rich dynamical landscape, which we leave for future work. Declaration of Interests The authors report no conflict of interest. Appendix A One-dimensional nematohydrodynamics equations Here we present the reduced nematohydrodynamic equations for the case of a unidirectional flow. For unidirectional flows i.e. a 1 D formalism, we consider variations only in the direction across the width of the channel. This results in the following nematohydrodynamic equations: \displaystyle\frac{\partial Q_{xx}}{\partial t} \displaystyle=\Gamma K\frac{\partial^{2}Q_{xx}}{\partial y^{2}}+Q_{xy}\frac{\partial u_{x}}{\partial y}+\Gamma CQ_{xx}\left(S^{2}_{\mathrm{nem}}-S^{2}\right)-2\lambda Q_{xx}Q_{xy}\frac{\partial u_{x}}{\partial y}, (15) \displaystyle\frac{\partial Q_{xy}}{\partial t} \displaystyle=\Gamma K\frac{\partial^{2}Q_{xy}}{\partial y^{2}}-Q_{xx}\frac{\partial u_{x}}{\partial y}+\Gamma CQ_{xy}\left(S^{2}_{\mathrm{nem}}-S^{2}\right)+\frac{\lambda}{2}\frac{\partial u_{x}}{\partial y}-2\lambda Q_{xy}^{2}\frac{\partial u_{x}}{\partial y}, \displaystyle\rho\frac{\partial u_{x}}{\partial t} \displaystyle=\eta\frac{\partial^{2}u_{x}}{\partial y^{2}}+F+F_{\text{b}}. The backflow contribution is given by: \displaystyle F_{\text{b}}=\frac{\partial\sigma_{xy}}{\partial y} \displaystyle=2\Big(H_{xy}\partial_{y}Q_{xx}+Q_{xx}\partial_{y}H_{xy}-H_{xx}\partial_{y}Q_{xy}-Q_{xy}\partial_{y}H_{xx}\Big) (16) \displaystyle+\lambda\Big(4Q_{xx}Q_{xy}\partial_{y}H_{xx}+4H_{xx}Q_{xy}\partial_{y}Q_{xx}+4H_{xx}Q_{xx}\partial_{y}Q_{xy} \displaystyle\quad+4Q_{xy}^{2}\partial_{y}H_{xy}+8H_{xy}Q_{xy}\partial_{y}Q_{xy}-\partial_{y}H_{xy}\Big), where the scalar order parameter is S^{2}=Q_{xx}^{2}+Q_{xy}^{2} , and the molecular fields are \displaystyle H_{xx} \displaystyle=CQ_{xx}\left(S_{\mathrm{nem}}^{2}-S^{2}\right)+K\frac{\partial^{2}Q_{xx}}{\partial y^{2}}, (17) \displaystyle H_{xy} \displaystyle=CQ_{xy}\left(S_{\mathrm{nem}}^{2}-S^{2}\right)+K\frac{\partial^{2}Q_{xy}}{\partial y^{2}}. (18) Here, the terms in the Q -tensor evolution equations represent: elastic relaxation of distortions ( \Gamma K\partial^{2}_{y}Q_{ij} ), flow alignment ( Q_{ij}\partial_{y}u_{x} and related \lambda terms), and relaxation towards the nematic order parameter ( \Gamma CQ_{ij}(S_{\mathrm{nem}}^{2}-S^{2}) ). In the momentum equation, viscosity ( \eta\partial_{y}^{2}u_{x} ), external forcing ( F ), and nematic backflow effects ( F_{\text{b}} ) are included. The backflow term accounts for the feedback of director reorientation on the fluid velocity through the coupling between the Q -tensor and the molecular field tensor H . Appendix B Boundary layer analysis for varying \mathbf{Q} state In this section, we perform a boundary layer analysis for the varying \mathbf{Q} state for the boundary layers that are formed for S near the walls for small \epsilon . Considering the steady state, Eqs. ( 11 ), the second equation can be rewritten as \frac{d}{dy}\left(S^{2}(y)\frac{d\theta}{dy}\right)=0, giving S^{2}(y)\frac{d\theta}{dy}=m, where m is a constant. Substituting this in the first equation of Eqs. ( 11 ) for S we obtain \frac{d^{2}S}{dy^{2}}-\frac{4m^{2}}{S^{3}}+\frac{C}{K}S(1-S^{2})=0. (19) The value of m is determined as m=\theta^{\prime}(\pm L/2) since S(\pm L/2)=1 . Hence for the uniform \mathbf{Q} state we have m=0 and for the lowest energy ( n=1 ) varying \mathbf{Q} state we have m\approx\pm\pi/L . Substituting m\approx\pm\pi/L in equation ( 19 ) and non-dimensionalizing with length scale L/2 , gives the following ODE: 4\epsilon\frac{d^{2}S}{dy^{2}}-\frac{4\pi^{2}\epsilon}{S^{3}}+S(1-S^{2})=0. (20) Here \epsilon=K/(CL^{2}) and we assume 0<\epsilon\ll 1 with the boundary conditions of the ODE S(-1)=S(1)=1 . B.1 Outer solution in the channel bulk Setting \epsilon=0 , we get the equation S(1-S^{2})=0, implying S^{(0)}_{out}=1 as the physically relevant solution. Performing a regular perturbation expansion of the outer solution gives S_{out}(y)=1+\epsilon S^{(1)}_{out}+O(\epsilon^{2}). Substituting and balancing terms at O(\epsilon) leads to S^{(1)}_{out}=-2\pi^{2}. Hence, the outer (bulk) solution to O(\epsilon) is S_{out}(y)=1-2\pi^{2}\epsilon+O(\epsilon^{2}). B.2 Inner solution near the channel boundaries We consider the top boundary without loss of generality, and define a rescaled variable, Y=\frac{1-y}{\delta}, where 0<\delta\ll 1 . We now write the full solution to O(\epsilon) as S(y)=1-2\pi^{2}\epsilon+v(Y), where v(Y)\sim O(\epsilon) . Substituting the expansion in equation ( 20 ) gives \displaystyle 4\epsilon\frac{1}{\delta^{2}}\frac{d^{2}v}{dY^{2}}-4\pi^{2}\epsilon\frac{1}{(1-2\pi^{2}\epsilon+v)^{3}}+(1-2\pi^{2}\epsilon+v)(1-(1-2\pi^{2}\epsilon+v)^{2})=0. Substituting \delta=\sqrt{2\epsilon} and keeping terms of {O}(1) we get, v(Y)=Be^{-Y},\,\,Y\geq 0. This solution decays in the bulk. To find B , we use the boundary condition S(1)=1 giving v(0)=B=2\pi^{2}\epsilon and leading to a solution v(y)=2\pi^{2}\epsilon\,e^{-\frac{1-y}{\sqrt{2\epsilon}}}. A similar boundary layer appears near the bottom wall y=-1 with Y=(y+1)/\delta . Hence, the total solution of the system is given by S(y)=1-2\pi^{2}\epsilon+2\pi^{2}\epsilon\left(e^{-\frac{1-y}{\sqrt{2\epsilon}}}+e^{-\frac{1+y}{\sqrt{2\epsilon}}}\right)+O(\epsilon^{2}). Appendix C Additional results for different parameter combinations Here we present further plots showing the free energy changes of the Bowser and Dowser states as a function of the forcing F for different parameter values. For a non-zero flow aligning parameter, the plot in figure 2 (a) is modified to figure 7 (a) ( \lambda=0.2 ) and figure 7 (b) ( \lambda=1 ). Keeping \lambda=0 and increasing K , gives the plot in figure 7 (c) where we see that the ordering of the instabilities has changed, i.e. the two Dowser states become unstable before the Bowser state. For the parameter values corresponding to (b) and (c), a full bifurcation diagram for the 1 D model is shown in figure 7 (d) and (e), respectively. In figure 7 (d), we still observe the unsteady periodic and chaotic behaviours in the flow aligning regime corresonding to \lambda=1 . In figure 7 (e), which corresponds to a larger elasticity K we again still observe unsteady flows. Furtheremore, here we find that the steady states are stable for larger F values compared to figure 3 (a), as well as an extended window of periodic behaviours in the unsteady regime. Figure 7: Steady flow states for pressure-driven nematics in a channel for parameters (a) C=0.025 , K=0.01 , L=20 , \lambda=0.2 , (b) C=0.025 , K=0.01 , L=20 , \lambda=1 and (c) C=0.025 , K=0.1 , L=20 , \lambda=0 . Vertical dashed lines show when the solution branches become unstable. (d) and (e) show the full bifurcation diagram where the peaks in the time series of \mathcal{F}_{\mathrm{nem}} are plotted as a function of F for the parameters corresponding to (b) and (c), respectively. In these panels, initial flow velocity is zero and different colours correspond to different initial orientation profiles with red favouring Bowser states, blue and cyan favouring Dowser states and gray corresponding to random initial orientations.