Gran Sasso Science Institute Astroparticle Physics Abstract Abstract Astrophysical and cosmological observations performed within the last century provide extensive evidences that the comprehension of the Universe is not complete and that an ingredient known as dark matter (DM) is required to interpret the measurements. One of the most supported class of theories suggests that dark matter is composed of weakly interactive massive particles (WIMPs). As the Milky Way is expected to reside in a halo of these particles, a possible experimental methodology to observe them is to exploit the potential weak interaction between WIMPs and standard matter, which results in the recoil of the latter. Due to the strength of this interaction, direct detection experiments for WIMPs are searching for ultra rare events, by exposing large volume of instrumented mass to detect recoils of regular matter. The motion of the Sun and Earth with respect to the Galactic Rest Frame and the foreseen non relativistic nature of the WIMPs, induces an apparent wind of DM particles coming from the Cygnus constellation, which imprints a strong directional dependence in the recoil spectrum. Direct detection experiments capable of measuring the angular features of the recoils gain access to a wide range of advantages. These include the possibility to positively claim a discovery of DM, along with the ability to constrain DM properties. The CYGNO project sets into this context, with the aim to deploy a large directional detector for rare event searches as DM. It comprises a gaseous time projection chamber filled with a He:CF 4 gas mixture, an amplification stage based on a triple stack of gas electron multiplier (GEM) optically readout employing scientific CMOS cameras and photomultiplier tubes (PMTs). This setup allows to perform the imaging of the recoil tracks, measuring on an event by event basis the energy, the direction and the topology of the tracks. The advantage of the optical readout through sCMOS cameras is that it allows to image large areas with an high granularity but a reduced amount of sensors. The major drawback is that the resulting small solid angle coverage of the optical setup ends up limiting the number of photons that reach the light detectors, effectively affecting the energy threshold. In this thesis, it is presented the work carried out with small CYGNO prototypes in order to maximise the light yield without degrading spatial and energy resolution. Different number of GEMs of various thicknesses are tested together with the addition of an extra electrode to produce strong electric fields below the last GEM. The latter addition proved to be an innovative way to enhance the light production below the GEM holes for the He:CF 4 gas mixture, which allowed to improve the light yield by a factor close to 2 and reducing the intrinsic diffusion of the amplification structure by tens of micrometers. Minimising the electron cloud diffusion while drifting towards the amplification stage is very relevant to precisely measure the topological information of the recoil tracks. The addition of highly electronegative gases induces the electrons freed by the passage of an ionising particle to be captured by them in few micrometres. The negative ions produced are drifted in place of the electrons and their larger mass allows them to remain thermal with the gas, strongly reducing the diffusion. This technique is usually referred to as Negative Ion Drift (NID) operation. Using a CYGNO prototype, the addition of 1.6% of SF 6 to the He:CF 4 gas mixture is demonstrated to produce negative ions drift operation reaching gas gains of the order of 10 4 . A strong reduction in diffusion is measured, with diffusion coefficient as low as 45 \mu m/ \sqrt{\text{cm}} , among the smallest ever measured in a gas detector. The potential performances of directional detectors in the context of a direct DM search are analysed with the use of rigorous statistical tools. The improvement in setting limits in the WIMP to nucleon and DM mass parameter space with a directional detector are evaluated employing the future expected performances of the CYGNO experiment. In addition, the improvement in the capability of discerning two different DM models exploiting a directional detector in comparison to a non directional one is analysed. It is found that, taking advantage of the angular feature, the two models considered can be distinguished with orders of magnitude less events than conventional non directional detectors. Introduction The last sixty years saw the flourishing of fundamental particle physics, with the development and experimental verification of the Standard Model (SM), capped with the discovery of the Higgs Boson in 2012. Recent years also witnessed the first detection of gravitational waves, phenomena predicted by the fundamental theory of gravity, the General Relativity. This detection, followed by many others, marked an extreme agreement of experimental data with the theoretical predictions. Yet, the SM is known to have various limitations and issues, such as the complete lack of the description of the gravitational force. Moreover, at the same time, numerous astrophysical and cosmological observations suggest the knowledge of the Universe is still incomplete, with the leading cosmological model, the \Lambda CDM, advocating for the existence of new constituents of the Universe, the dark matter (DM) and the dark energy. In particular, DM is observed to behave gravitationally as a mass, challenging the current knowledge of either gravity or particle physics. One of the most supported hypotheses speculates that DM is composed of one or more types of particles different from the ones described in the Standard Model. Indeed, theories such as the supersymmetric model or the QCD axions were developed in order to tackle some issues of the Standard Model and ended up predicting the existence of a particle which turned out to be a perfect candidate for DM. Among these, the Weakly Interactive Massive Particles (WIMPs) are a class of DM matter candidates in which DM consists in a non relativistic, with GeV/c 2 to TeV/c 2 masses, that weakly interacts with Standard Model particles. Indeed, a stable, weakly-interacting particle in thermal equilibrium with the early Universe would be able to reproduce the observed relic DM density. The measurements of the rotation curve of the Milky Way suggest the presence of high concentrations of DM at the Galactic radius of the Sun, with an halo embedding the entire Galaxy. Assuming DM can interact with SM matter other than gravitationally, in order to detect it, it is possible to exploit the weak interaction with regular matter and measure the recoils induced by a DM interaction. This is known as direct detection and the fundamental strategy is to expose large amount of instrumented mass and wait for DM to produce recoils in it. Direct detection experiments look for nuclear recoils of low energy, 1-100 keV, with an expected rate below 1 event per kg year. Such very low expected rates imply detectors with extremely challenging requirements on the allowed experimental backgrounds. Classical background minimisation techniques are deep underground operation (to suppress cosmic rays), use of radio-pure components (to avoid natural radioactivity) and active or passive shielding of the detector. The motion of the Sun and Earth around the centre of the Galaxy induces an apparent wind of WIMPs coming from a fixed direction in the frame of reference in which the Galaxy is at rest. This motion imprints a strong directional feature in the distribution of the recoils, which cannot be mimicked by any form of background, also thanks to the rotation of the Earth around its own axis. Thus, differently from the energy distribution of the recoils, which is expected to possess a generic falling exponential shape, the access to the angular distribution opens the possibility for a positive claim for a DM discovery and even constrain some characteristics of the DM models. The CYGNO project intends to construct a large, \mathcal{O} (30) m 3 , directional detector for rare event searches, such as DM. The detector is a gaseous time projection chamber, a detector intrinsically sensitive to the topology of the recoil tracks which allows to measure their direction. A helium and fluorine rich gas mixture is employed, in order to be sensitive to both spin-depedent and spin-independent interactions. CYGNO will be equipped with an amplification stage composed of three gas electron multipliers (GEMs) and will be optically readout with photomultiplier tubes and scientific CMOS cameras. The latter allows to image large readout areas with high sensitivity while maintaining extremely good granularity. This, in turn, grants the capability to measure the direction of the recoils. Various CYGNO prototypes have been built and tested both overground and underground, to determine their performances and their viability in a realistic environment for the DM search. This work has been carried out in the context of the CYGNO experiment with the goal of optimising the light yield and diffusion properties of the detector. These are extremely relevant parameters as they directly characterise the quality direction and energy can be measured with. In addition, an assessment of the potential of such directional detectors in the directional search is dealt with in this work. The structure of the thesis is outlined in the following. In Chapter 1 , a brief overview of the theoretical arguments and experimental observations which lead to consider the existence of DM a paradigm of modern physics is presented. The Chapter also addresses the most relevant theoretical models which are proposed to explain its nature. In Chapter 2 , the phenomenology of the WIMP scattering with nuclei is given in the context of the direct detection of DM. The basic principles, the observables and the challenges of the direct detection technique are also discussed and the current status of the direct detection is presented. In addition, large focus is dedicated to the directional search, presenting its numerous advantages and portraying the state of the art of directional detectors for DM searches. In Chapter 3 , an extensive description of the CYGNO experiment is provided. The concept of the detector is thoroughly described with particular attention to the main feature of the CYGNO project, the optical readout. The most important results obtained with several prototypes are also depicted and a glimpse to the future prospects is furnished. In Chapter 4 , the issue of the analysis of scientific CMOS camera images is described, detailing the algorithm developed and its optimisation. Moreover, it is detailed the analysis strategy to assess the diffusion characteristics of the CYGNO detectors employed in the studies presented in the subsequent Chapters. In Chapter 5 , the study of the optimisation of the amplification stage is detailed. Different types and number of GEMs are tested together with a varying percentage of helium in the gas mixture. Moreover, the addition of an extra electrode below the last GEM to induce strong electric fields is examined, also with the help of electric field simulations. The performances of the different amplification structures are analysed and compared in terms of light yield, energy resolution and spatial diffusion. In Chapter 6 , the study of the reduction of the diffusion in the gas by means of the addition of a high electronegative gas is described. The principle of the negative ion drift operation for the SF 6 gas is given and the experimental results in the context of the CYGNO optical readout are presented. In Chapter 7 , a detailed study of the directional performances of a CYGNO-like detector is given. The advantages obtained by using a directional detector in the determination of the upper bound limits for a DM search with a CYGNO future detector is analysed in a rigorous statistical framework. In addition, the capabilities of a directional detector in discerning different DM hypotheses are worked out. Finally, the Conclusions report the final comments and a summary of the results obtained in this work. Chapter 1 Dark matter In the last decades, the fact that a broad number of astrophysical and cosmological observations is suggesting that something is lacking in the description of the Universe has become a well established paradigm of modern physics. The measurements indicate that an ingredient different from the known forces and particles is required to account for the experimental findings. As it behaves like a mass, it is also known as dark matter (DM). Even though experimental efforts in the years unveiled details of its phenomenology, its nature is still elusive and unknown. One of the most credited possible explanations assumes that this is indeed a form of matter which makes up the 84% of total [ 1 ] and plays a fundamental role in the formation of the organised structures of the Universe [ 2 ] . A plethora of theoretical models have being trying to correctly describe this elusive phenomena, while experimental efforts have being relentlessly aimed at detecting clear signatures of DM, pushing the current research activities to become very active and relevant in the context of present and future research. In the following, Section 1.1 is dedicated to a short overview on the astrophysical and cosmological measurements which lead to DM hypothesis, whilst Section 1.2 focuses on the description of the most supported theoretical explanation of this phenomenon. 1.1 Evidence for dark matter Evidences for the presence of an ulterior ingredient to the Universe, commonly referred to as dark matter (DM), are present is many astronomical observations spanning all the scales of the Universe, from single galaxies to the largest structures. In the following Sections, the most critical and decisive will be briefly illustrated, starting from the galactic scale up to the cosmological one. For a more comprehensive review, see the reference [ 3 ] . 1.1.1 Galactic rotation curves One of the most compelling and established evidences of DM derives from the observation of the rotation curves of spiral galaxies, including the Milky Way [ 4 , 5 ] . In these galaxies, most of the stars are located in the central part, called bulge, around which largely flat spiral arms composed of stars and gas clouds are moving in approximately circular orbits. The rotation curve is the profile of the circular velocities of the stars and gas clouds of the galaxy along the radial distance from the centre. When considering a rotating galaxy as a closed system, an object of mass m at a radius R from the centre is subject to a centripetal force equal to the gravitational force of the overall mass present within the same radius M(R) : m\frac{v^{2}}{R}=\frac{GM(R)m}{R^{2}}, (1.1) with G the gravitational constant and v the circular velocity of the object with mass m . Hence, the rotational velocity of the constituents of a galaxy can be expressed as a function of R and of the total mass M as: v=\sqrt{\frac{GM(R)}{R}}. (1.2) It is reasonable to assume that the large majority of the mass of a galaxy is located within a characteristic radius R_{c} , estimated by measurements to fall between 5 and 10 kpc [ 4 ] . So, for RR_{c} the the mass M is constant and the velocity decreases as \sqrt{R} . Figure 1.1: Example of the rotation curve measurement of the galaxy NGC6503, taken from [ 5 ] . The solid line represents the combined fit of the data, while the dashed refers to the gas component, the dotted to the visible one, and the dash-dotted to the DM. The rotation curve can be measured via the Doppler shift of the 21 cm emission line of the of the HI. A large set of rotation curves, extending well beyond the optical limit and down 200 kpc, has been measured, exhibiting similar results. Figure 1.1 shows, as an example, the experimental findings on the rotation curve of the galaxy NGC6503 [ 5 ] . The measured orbital velocity increases linearly as expected at small radii but stays constant at large radii, contrary to expectation. This flatness suggested the existence of an additional and invisible mass in the form of a dark galactic halo around any spiral galaxy, which does not interact electromagnetically. This halo of matter appears to be consistent at first order to a spherical distribution with a density proportional to R^{-2} . 1.1.2 Galaxy clusters velocity dispersion Galaxy clusters are systems composed of thousands of galaxies and gas clouds gravitationally bound to each other. By applying the Virial theorem, it is possible to relate their time average kinetic energy to the total gravitational potential energy of the system [ 6 ] : \sum_{i}m_{i}v_{i}^{2}=\sum_{i}\sum_{j\neq i}\frac{Gm_{i}m_{j}}{r_{ij}} (1.3) with i and j representing the index on the galaxies of the cluster, m the mass of a galaxy, v the time average velocity of the galaxy, G the gravitational constant and r_{ij} the distance between the galaxies i and j . By performing an average on the galaxies, a relation can be obtained that correlates the total mass of the cluster to the dispersion of the velocities of its galaxies: M\simeq\frac{5}{3}R_{G}\frac{\left\langle v^{2}\right\rangle}{G}, (1.4) where it is assumed that the galaxies are uniformly distributed in a sphere of radius R_{G} . The application of the Virial theorem to the Coma Cluster by Zwicky in 1933 provided the first experimental observation of a missing mass component in the Universe [ 6 , 7 ] . By measuring the line of sight velocities of the galaxies of this globular cluster via redshift and assuming a spherical distribution, Zwicky obtained the velocity dispersion of the Coma cluster and its gravitational mass through the Virial theorem. In parallel, Zwicky estimated the cluster mass from its luminous component assuming an average luminosity to mass ratio of galaxies. The mass estimated from the gravitational component resulted \mathcal{O} (10 2 ) larger than measured luminous mass, advocating for the presence of matter in the galaxy cluster structure that is not interacting electromagnetically. Many other measurements on different galaxy clusters soon followed with consistent results [ 8 ] . Basically, the velocities of the galaxies appear too large to be explained by the gravitational potential caused by the luminous matter of the cluster. 1.1.3 X-ray emission from galaxy clusters The large amount of gas present in between galaxies can be used to assess the galaxy cluster mass by studying their X-rays emission, whose intensity is strongly related to the gravitational potential experienced due to the surrounding mass. Assuming the gas plasma to be in hydrostatic equilibrium, it is possible to relate gas density \rho and pressure P at a given distance r from the centre of the system to the mass M of the cluster as [ 9 ] : \frac{1}{\rho(r)}\frac{dP(r)}{dr}=-\frac{GM(r)}{r^{2}}, (1.5) Inserting the perfect gas law to make the dependence on the temperature of the gas explicit, the relation can be transformed in: \frac{d\log\rho}{d\log r}+\frac{d\log\ T}{d\log r}=-\frac{r}{T}\left(\frac{\mu m_{p}}{k_{B}}\right)\frac{GM(r)}{r^{2}}, (1.6) where \mu is the average molecular weight of the primordial gas of about 0.6, and m_{p} is the mass of the proton, T is the temperature of the gas and k_{B} the Boltzmann constant. Direct measurements suggest that \rho is a power law in r with a spectral index between -1.5 and -2 [ 9 ] . By adding this density model, the temperature of the gas can be parametrised as follows: k_{B}T\sim(1.3\text{--}1.8)\text{keV}\left(\frac{M_{r}}{10^{14}M_{\odot}}\right)\left(\frac{1Mpc}{r}\right), (1.7) where a typical mass of a cluster of 10 14 solar masses and a radius of 1 Mpc were assumed in the calculation. Typical measured temperatures of galaxy clusters are of the order of 10 keV, pointing at the existence of non-luminous matter which adds gravitational potential to the visible one which is required in order to reproduce the observations under these assumptions. 1.1.4 Gravitational lensing Figure 1.2: On the left, a scheme of the working principle of the gravitational lensing (© Horst Frank/Designergold). On the right, an example of a horseshoe Einstein ring due to gravitational lensing taken from a Hubble image [ 10 ] . The gravitational lensing provides additional evidences of the presence of DM. This phenomenon is predicted by General Relativity and is caused by the space-time distortions induced by the energy and mass distributed within it. In a flat region of space, particles and light travel on a straight path in the 3D space. Yet, in presence of a large mass concentrated in a small region, the space-time around it is distorted so that the straight paths are deflected in the direction of the mass. A schematic illustration of the gravitational lensing principle is shown in left panel of Figure 1.2 . When a massive object is present between an observer and a source of photons, its gravitational potential modifies the space-time, effectively deflecting the light coming from the source and generating multiple images of the original object at the source, as shown in right panel of Figure 1.2 . In this context, the mass distribution between the observer and the photon source is called lens . The angle \theta of deflection from the straight path of a light ray passing at a distance r from a lens of mass M is expressed in the simple Schawrzschild approximation by [ 11 ] : \theta=\sqrt{\frac{4GM}{rc^{2}}}, (1.8) Figure 1.3: Observation of the bullet cluster performed with the Chandra X-ray telescope [ 12 ] . Superimposed in green are the contour lines representing the gravitational potential measured with gravitational lensing. with c the speed of light in vacuum. As a result, measuring the deflection allows to infer the mass of the object causing it. Depending on the mass and the mass distribution of a lens, the effects of the gravitational lensing are different. Strong lensing happens when mass of the lens is large and its position change in the sky is small compared to Earth’s velocity. The effects are resolvable with telescopes in single images [ 12 ] . Weak lensing is produced by smaller masses and results in a distortion of galaxy images due to the bending of light [ 13 ] . Finally, when the mass of a lens is so small that it does not produce visible deformation, but only affects the light intensity of the luminous sources, it is called microlensing [ 14 ] . Different experimental and analysis techniques allow to retrieve evaluation of the masses distributions in between the observer and the luminous sources. An example of a strong proof of the presence of missing mass in galaxy clusters can be obtained by studying the ones that are merging one into the other, comparing the X-rays emission of the hot gases to the mass distribution inferred from gravitational lensing. In this context, while stars are not expected to collide due to their small size with respect to the dimension of the cluster, the intergalactic hot gas interacts mainly electromagnetically. As a consequence, the gas slows down in the direction of the motion of the galaxies, while its temperature rises and the X-rays emission becomes more intense. In Figure 1.3 , the example of the Bullet cluster is presented. The red halo highlights where the X-ray emission is the strongest and the green contour lines show the gravitational potential estimated with lensing. The observed displacement between these two measurement strongly support the hypothesis that more mass than the one visible has to be present, along with the hint that DM is not collisional, being unscathed by the encounter of the two clusters. 1.1.5 Cosmological scale One of the most compelling indications of DM existence is inferred by measurements of cosmological-related quantities. The currently most supported theory of cosmology is the Big Bang model, which states that the Universe was once very small, dense and hot, and later expanded to reach the shape it has today [ 15 ] . The Friedmann equations describe the expansion of space-time in a homogeneous and isotropic Universe within the context of General Relativity. These assumptions originate from the cosmological principle, or else the notion that the Universe is homogeneous and isotropic when viewed on a large enough scale. The cosmological principle implies a Friedmann–Lemaître–Robertson–Walker metric, that, when applied to General Relativity, allows to express the space-time evolution and its geometry as a function of the energy density of some constituents fluid. The velocity of the expansion of the Universe can be then expressed: H^{2}:=\left(\frac{\dot{a}}{a}\right)^{2}=\frac{8\pi G}{3}\rho(a)-\frac{k}{a^{2}}, (1.9) with H the Hubble parameter, a the scale factor of the Universe, \rho the energy density of the fluid, k the curvature of the 4-dimensional space-time. The scale factor of the Universe is a normalisation term which represents the dimension of the Universe. In general, its value at the time t=0 is taken as zero and subsequently grows with time due to the Universe adiabatic expansion. The fluid which constitutes the Universe can be described as a composed by different components. The most supported theoretical framework which depicts the composition and evolution of the Universe is the \Lambda CDM model [ 16 ] . The \Lambda CDM assumes that the energy density \rho is, in fact, the sum of the energy densities of fluids with different properties: • Radiation \rho_{r} which comprises ultra-relativistic particles such as photons and neutrinos for which \rho_{r}\propto a^{-4} is valid; • Matter \rho_{m} which includes the non-relativistic matter among which the baryonic matter and also the non-baryonic matter like the DM. In this case \rho_{m}\propto a^{-3} ; • Cosmological constant \rho_{\Lambda} that accounts for the dark energy (DE), an unknown and mysterious form of energy which is responsible for the acceleration of the Universe’s expansion. For the DE, \rho_{\Lambda} is independent of a . All of these constituents of the Universe combined with Equation 1.9 , describe the evolution of the Universe. A common notation used to express all the Universe constituents into the Friedmann equation is to relate each one’s energy density with the critical density \rho_{c} , the density required for the Universe to be perfectly flat: \Omega_{i}=\frac{\rho_{i}}{\rho_{c}}, (1.10) Friedmann equation can be rewritten as: H^{2}=H_{0}^{2}\left(\Omega_{r,0}(1+z)^{4}+\Omega_{m,0}(1+z)^{3}+\Omega_{\Lambda,0}+\Omega_{k,0}(1+z)^{2}\right), (1.11) with z the redshift which replaces a following z=\frac{a_{0}}{a}-1 , the subscript 0 denotes that the variable is evaluated now, and \Omega_{k,0} does not represent a constituent of the Universe, but is the curvature term of Equation 1.9 . If the sum of all the \Omega components is 1, then the total energy density of the Universe is equal to the critical one and the Universe is flat. The term \Omega_{m} can be further split into the baryonic part and the DM one. Any measurement able to constrain \Omega parameters provides information on the structure of the Universe and help quantify the amount of DM. 1.1.5.1 Cosmic microwave background (CMB) Figure 1.4: CMB anisotropies measured by the PLANCK satellite. Figure by ESA https://www.esa.int/ESA_Multimedia/Images/2013/03/Planck_CMB . A possible method to constrain the \Omega parameters is to exploit the measurement of the cosmic microwave background (CMB), a relic radiation originated during a period called recombination . At the very early stages of the Universe, few seconds after the Big Bang, the temperature, inversely proportional to the adiabatic expansion of the Universe [ 17 ] , was of the order of 100 MeV. The cosmic plasma comprised photons, neutrinos, electrons, positrons and baryons in thermal equilibrium. Every photon emitted at those times is lost as they interacted soon after with other particles, being in thermal equilibrium. With the expansion of the Universe, the temperature dropped resulting in reduction of the intensity of the interactions. When the temperature reached values around 1 eV, the energy carried by photons started to be not enough to prevent protons and electrons from combining and forming the first atoms. This is known as the recombination period. As a consequence, the photons emitted in that era were not absorbed and can be still detected today as the CMB. This relic radiation possesses a spectrum which follows the black body radiation spectrum, and its isotropy reaches levels of \frac{\Delta T}{T}\sim 10^{-5} [ 1 ] . Nevertheless, small anisotropies exist and are shown in Figure 1.4 , from the measurement of the PLANCK collaboration. These anisotropies are related to fluctuations in the local gravitational potential and any kind of phenomenon which mirrors its behaviour on the energy density [ 18 ] . Examining them carefully can provide constraints on various scenarios hypothesised for the early Universe. The temperature anisotropies are usually decomposed in the spherical harmonic functions \frac{\Delta T}{T}=\sum_{l}\sum_{m=-l}^{m=l}a_{lm}Y_{l}^{m}(\theta,\phi), (1.12) and the power spectrum is computed from: C_{l}=\left\langle|a_{lm}|^{2}\right\rangle_{m} (1.13) Figure 1.5 shows the temperature anisotropies as presented by PLANCK collaboration as a function of the spherical harmonics. The blue line represents the fit of the \Lambda CDM model, the simplest parametric model of the Big Bang which includes DM and DE. The temperature fluctuations follow the oscillation of gravitational wells, matter, DM and photon plasma. The first intense peak is related to the base frequency of the energy and matter density oscillation. Its position is strongly related to the value of total curvature of the Universe at the recombination time. The other peaks are overtones of the fundamental frequency. The difference in intensity is related to the amount of baryonic matter (for the second peak) and non-baryonic one (for the subsequent peaks) as plasma oscillation can interact destructively with the fluctuation of the gravitational potential wells. The model fits very well the data and allows to measure the \Omega components from the relative intensity of the peaks and their position, even though more complete and precise analyses which include other measurable quantities is described in [ 1 ] . Figure 1.5: Temperature anisotropies spectrum in spherical harmonics presented by PLANCK [ 1 ] . The blue line is the \Lambda CDM model fit of the experimental data. The CMB anisotropy description is one of the possible cosmological measurements which can provide information on the \Omega components of the \Lambda CDM model. The art on the \Omega relative densities which are summarised in Table 1.1 , taken from [ 1 ] : Component Density parameter Planck results with 68% CL Radiation \Omega_{r} \sim 9\times 10^{-5} Baryonic matter \Omega_{b} 0.0489\pm 0.0003 Non-baryonic matter \Omega_{nb} 0.2607\pm 0.0019 Dark energy \Omega_{\Lambda} 0.6889\pm 0.0056 Total \Omega_{tot} 0.9993\pm 0.0019 Table 1.1: Table summarising the Planck combined results on the \Omega parameters of the \Lambda CDM model, taken from [ 1 ] . The \Omega_{tot} is perfectly consistent with 1, suggesting that the Universe is flat. The non-baryonic matter which is considered to mostly be DM is a required constituent of the Universe. On top of this, its abundance is about 26% of the total energy density, comprising 84% of total matter. 1.1.5.2 Structure formation Figure 1.6: Example of the N-body simulation result for the Illustris [ 19 ] . Different redshift are displayed: top left z=7, top right z=3, bottom left z= 1, bottom right z=0. The formation of large scale structures, such as galaxies and clusters of galaxies, is a very relevant test bench for the DM characteristics and evidence of its presence. Since today’s highly inhomogeneous Universe evolved from a very uniform and smooth state at the time of recombination (when density fluctuations were of the order 10 -5 ), the analysis of the large structures can provide constraint on what influenced such evolution. The homogeneity of the Universe can be expressed as the fluctuation intensity of the fluid energy density of the Universe \rho defined in the previous Section. As a simple approximation, until the Universe is radiation dominated ( \rho_{r}>>\rho_{m},\rho_{\Lambda}) , \frac{\delta\rho}{\rho} can grow as the logarithm of the scale factor a . Only in a matter dominated epoch, the perturbations can inflate linearly. However, if only baryonic matter existed, the linear growth of the perturbations would start only after recombination. Scaling them to the present day, \frac{\delta\rho}{\rho} would still be of the order of 10 -2 , a quite uniform Universe. A non linear growth of the perturbations can be induced if a different matter species that decouples from photon before recombination is introduced in this picture. This would generate potential wells where baryonic matter falls into immediately after the recombination, provoking non linear enhancement of the perturbations. This different, non baryonic form of matter would perfectly fit as DM. In order to better detail the peculiarities of this DM assumption in the evolution of these large structures, complex N-body simulations are used. A set quantity of particles belonging to the primordial fluids (radiation, DM and baryonic matter) is prepared in the abundance present at the very early stages of the Universe, inferred by the PLANCK results. The system is left to evolve following the gravitational attraction of the constituents and the interactions between the fluids as derived from particle physics. The evolution is continued until the present day and the large structure formed and formation processes are checked with the astronomical observations. Various N-body simulations like Millennium [ 20 ] , \nu^{2} GC [ 21 ] and Illustris [ 19 ] are employed and typically utilise billions of particles in order to generate a modern universe few hundreds of light-years wide. Figure 1.6 exemplifies the outcome of some of these simulations. For example, in the hypothesis that DM is made of particles (see next Section), some physical characteristics can modify the result of the simulation. If DM were made of relativistic particles at the moment of decoupling from baryonic matter, the pressure they induce would be enough to eliminate the small perturbations and large scale gas-structure would form first. The galaxies would be generated only afterwards from the collapse of these gaseous systems. Recent observation rule out the hypothesis of hot DM as they are too different from the simulation outputs [ 22 ] . As a consequence, the most supported model endorses a cold or warm DM hypothesis, with non-relativistic or semi-relativistic particles at the decoupling time, as simulations results succeed in reproducing the current measurements. 1.2 Candidates for dark matter Astronomical and cosmological observations based on gravitational probes are not consistent with the current picture of Universe particle and forces content. Thus, an ulterior ingredient is believed to be necessary to explain the measurements performed. Nevertheless, all of these hints derive from gravitational probes of observables. Various theories to explain these anomalies exist, and in the following, the most established will be reviewed. 1.2.1 Modified Newtonian Dynamics All the evidences of the lack of complete understanding of the Universe derived from the astrophysical and cosmological measurements are gravitational probes which assume the application of the Newtonian dynamics and General Relativity. Alternative models try to explain these observed discrepancies by modifying the underlying hypotheses on the laws of gravitation themself. These theories go under the name of Modified Newtonian Dynamics (MOND) and attempt to explain the observations by modifying Newtonian gravitational force to correctly predict the anomalies measured [ 23 , 24 ] . The core idea is that it exists a new fundamental acceleration constant a_{0} that marks the transition between Newton and deep-MOND regime. When the acceleration of the system a is smaller than a_{0} , the gravitational force scales differently than standard Newtonian gravity describes. On the contrary, at higher accelerations than a_{0} , the standard dynamics is recovered. With a_{0} estimated from the measurements of the galactic rotation curves as 10^{-10} cms -2 , the dynamics of galaxies and cluster of galaxies is affected, leaving untouched the Solar system scale. The theories are accurate and predictive at a galactic scale. In particular, the foreseen dependence of the rotation curve on the baryonic mass content of the galaxy is matching the expectation [ 25 , 26 ] . However, the difficulties in the MOND hypothesis resides in the capability to explain the discrepancies along the varied and different scales of the Universe. Large structure behaviours present in galaxy clusters and the CMB inhomogeneities require advanced extensions of the MOND in a relativistic form [ 9 ] . These theories become less predictive and more functions and parameters have to added to correctly describe the measurements [ 24 ] . The MOND theories largely succeeded in describing the galactic and galaxy cluster scale [ 24 ] , but fail with more complicated structures and phenomena, such as the Bullet cluster and the CMB [ 27 , 28 ] . While MOND theories propose an interesting view to solve the observation discrepancies, a complete theory is still missing [ 29 ] . 1.2.2 Primordial black holes Gravitational observation of a missing component in the Universe can be explained without the need to invoke a modification of the known laws of gravity, but rather assuming the existence of astrophysical objects that have yet to be resolved and identified. The possibility that black holes could be formed by the collapse of matter in the early Universe was proposed by Zeldovich, Novikov and Hawking in the late sixties [ 30 , 31 ] . These primordial black holes (PBHs) are expected to be produced before the period of the Big bang nucleosynthesis (BBN). The BBN is a period in which the temperature and density of the Universe are allowing the nuclear fusion of light elements, with the products of such reaction not being destroyed by the energetic photons thermally coupled to matter. This epoch permitted the generation of nuclei heavier than hydrogen and it is used to constrain the baryonic matter content of the Universe [ 32 , 33 ] . Being these massive objects produced before the BBN, they are decoupled from the rest of the baryonic matter and are not accounted for in the evaluation of its abundance [ 34 ] . For these reasons, since these massive objects do not enter in the CMB predictions, they could constitute the origin of the missing mass of the Universe and still be consistent with the evidences presented in this Chapter [ 35 ] . Indeed, for PBH masses greater than 5 \times 10 14 g, their lifetime is longer than the age of the Universe [ 36 ] . In fact, since PBH do not originate from collapse of massive star, their mass is unconstrained and could span many orders of magnitude. No positive discovery of a PBH has ever been claimed, but measurements of microlensing, gravitational waves, and CMB are putting stringent limits on the available parameter space of fraction of DM as PBH versus PBH mass [ 37 , 38 ] , leaving wide open only a region of masses between 10 17 and 10 21 g. 1.2.3 Dark matter as a particle The last decades have seen the completion of the discovery of the particles predicted by the most complete and known model of particle physics, the Standard Model (SM), with the observation of the Higgs boson at LHC in 2012. Nonetheless, the SM is known to possess several limitations, from the Higgs mass correction to the neutrino masses, to the strong CP violation, to the matter to antimatter asymmetry and the lack of the inclusion of gravity [ 39 , 40 ] . Extensions of the SM to tackle these problems predict the existence of new forces or particles, some of which have the characteristics to be a DM candidate. From the observation discussed in Section 1.1 , a series of characteristics that any model of DM as a particle has to respect can be obtained: • Non baryonic . Planck measurements of the CMB imply a non baryonic nature of these particles; • Abundant : Planck measurements found a \Omega_{nb}\sim 0.26, a much larger density than baryonic matter. The combination of number density of DM particles and their mass depends on the model in order to correctly match this abundance and the gravitational effects observed; • Neutral and colour-free . Electromagnetic interactions are excluded by the lack of interaction with photons which would have been otherwise detected. Strong interaction is also excluded since DM would lose energy and concentrate more in the galactic centres than what is observed [ 41 ] . • Weakly interacting . While at the moment experimental observations supporting the hypothesis that DM interacts other than gravitationally do not exist [ 36 ] , a form of weak interaction between DM and SM particles is hoped for in order to obtain a positive detection. As this non baryonic matter needs to be decoupled from the radiation-baryonic matter fluid already at the epoch of BBN, the intensity of interaction must be weak. This weak interaction does not refer to the SM electro-weak interaction, but can be any form of sub-weak strength type of interaction [ 36 ] . • Stable or extremely long lived. Due to the weak interaction, its presence in the early Universe and the measurements of its gravitational influence today, the DM particles are required to be preserved in large amount. • Warm or cold . DM relics can be classified according to their energy at the cosmological moment of decoupling from the baryonic matter fluid. Hot DM models require relativistic particles at the decoupling and typically masses are of the order \mathcal{O} (10) eV to match the abundance measured. Warm and cold DM models have need larger masses and smaller kinetic energies, with cold DM being completely non-relativistic. Large scale structure simulations are consistent with the existence of a hot population of DM, but only if its abundance is small, as it is shown to be incompatible with the formation of the large scale structures. Warm and cold DM allow the formation of the galaxies as observed, but the two modify the galactic structure. The information available on the galactic satellites are not conclusive enough to determine the type of DM population [ 42 ] . As a consequence of these characteristics, the modelling of a DM particle necessarily requires to extend the SM, because no SM particle satisfies the requirements listed above, not even neutrinos. Indeed, neutrinos are non baryonic neutral only weakly interactive particles, but the evaluation of the expected relic density does not match the observations. Moreover, being a warm-hot candidate the formation of small structures like dwarf galaxies is strongly hindered if neutrinos accounted for 100% of DM [ 43 ] . 1.2.3.1 WIMP One of the most studied and supported candidates are the Weakly Interactive Massive Particles (WIMPs), because these SM extensions predict type of particles which can naturally be produced in the correct abundance as thermal relics. The basic assumption behind WIMPs is that they are neutral massive particles with interaction with regular matter at the order of the weak scale or below. Starting from this assumptions, it is possible to relate the WIMP mass and cross section to today’s relic density [ 44 , 45 ] . Naming \chi a WIMP and \phi a SM one, and assuming that WIMPs can annihilate into SM ones, different epochs can be defined in the history of the Universe. In the hot early Universe, WIMPs were in thermal and dynamic equilibrium with SM, where the following expressions were valid: \phi+\chi\leftrightarrow\phi+\chi (1.14) \chi+\bar{\chi}\leftrightarrow\phi+\phi*. (1.15) With the expansion of the Universe, the density and the temperature drop so that the DM decouples from the SM. The number of DM particles is therefore fixed and this thermal relic abundance survives until now. This mechanism is called freeze-out. The number density of WIMPs n_{\chi} can be described by the Boltzmann equation \frac{dn_{\chi}}{dt}=-Hn_{\chi}-\left\langle\sigma_{A}v\right\rangle(n_{\chi}^{2}-n_{\chi,eq}^{2}), (1.16) with H the Hubble parameter, n_{\chi,eq} the number density in equilibrium and \left\langle\sigma_{A}v\right\rangle the thermal average of the annihilation cross section flux. The equation shows how the number density diminishes in time due to the spatial expansion of the Universe and is modified by the annihilation and generation of DM particles. In cosmology, the total entropy of the Universe is conserved during thermal equilibrium and its density s is often used as a variable to characterise the comoving volume of the Universe. As a consequence, the comoving number density Y_{\chi} of DM can be rewritten as: Y_{\chi}:=\frac{n_{\chi}}{s} (1.17) The moment of freeze-out is very relevant to determine the abundance of WIMPs now. It is defined as when n_{\chi,FO}\left\langle\sigma_{A}v\right\rangle\sim H (1.18) Moreover, the \Omega_{nb} parameter can be formulated as function of comoving quantities. Then, assuming that the comoving density now is the same that was present at the freeze out, it possible to derive: \Omega_{nb}=\frac{\rho_{\chi}^{0}}{\rho_{c}}=\left(\frac{s^{0}}{\rho_{c}}\right)m_{\chi}Y_{\chi}^{0}=\left(\frac{s^{0}}{\rho_{c}}\right)m_{\chi}Y_{\chi}^{FO}=\left(\frac{s^{0}}{\rho_{c}}\right)m_{\chi}\frac{H^{FO}}{s^{FO}\left\langle\sigma_{A}v\right\rangle}\propto\frac{m_{\chi}}{\left\langle\sigma_{A}v\right\rangle}, (1.19) with the superscripts 0 and FO referring to the time in the history of the Universe when the quantities are evaluated, respectively now and at the time of freeze out, m_{\chi} the WIMP mass, \rho_{c} the critical density, and \Omega_{nb} the density parameter of non baryonic matter (see Section 1.1.5 ). Since the PLANCK measurements show that \Omega_{nb} is \mathcal{O} (0.1), Equation 1.19 implies that the ratio of the interaction strength and the WIMP mass are of the same order. As the interaction is expected to be weak, the WIMP mass is also found at the weak scale. The fact that theories conceived to tackle SM issues naturally predicted DM candidate at the weak scale was considered extremely fascinating and takes the name of "WIMP miracle". Figure 1.7 shows the Y comoving number density of DM in the freeze out mechanism as a function of the temperature of the evolving Universe. Figure 1.7: Comoving number density Y as a function of the temperature along the evolution of the Universe for a WIMP mass of 100 GeV/c 2 . The solid black line is the solution to the Boltzmann equation that result in the measured DM density parameter \Omega_{nb} . The coloured bands show the diverse evolution for cross sections that differ of a factor 10, 100 and 1000 [ 46 ] . It is possible to formulate hypotheses in which the constraints on the DM mass and cross section interaction is loosen. The coloured bands represent the effects on the thermal relic density of the cross section intensity variation of various order of magnitude. Particles with the characteristics of the WIMPs discussed above can emerge in many scenarios beyond the SM. Here, the two most popular classes of theories will be discussed, that are supersymmetry (SUSY) and extra dimensions (EDi). The SUSY [ 47 , 48 ] is an extension of the SM which tries to address the gauge coupling unification and the Higgs mass corrections [ 48 ] by introducing a copy of each of the SM particle with opposite parity with respect to a new gauge transformation. The calculation of the Higgs boson mass includes corrections which are proportional to the mass of all the SM particles. In the SM, the series of corrections does not converge and the Higgs mass diverges. The new symmetry added by SUSY links bosons and fermions so that each boson of the SM has a so-called superpartner which is fermionic, and for each SM fermion there is a boson superpartner. These superpartners possess a different parity to this new gauge transformation which causes their correction to the Higgs mass to have opposite sign. Therefore, only if the superpartner masses are close enough the the SM ones, the overall contributions to the Higgs mass calculation are strongly reduced so that the series of correction converges. In a subclass of SUSY, the Minimal Supersymmetric Standard Model (MSSM), another ingredient is added, the R-parity conservation. R is a quantum number, combination of the baryonic number, the leptonic number and the spin. SM particles have R=1, while SUSY ones have R= - 1. The R-parity conservation implies that the decay of a SM particle can happen only with an odd number of SM particles. This was introduced to suppress the decay of the proton in supersymmetric particles. Akin, also supersymmetric particles can only decay in an odd number of themselves. In the SM, the gauge bosons of the electroweak symmetry (B, W 1 , W 2 , W 3 ) combine with Higgs fields in the electroweak symmetry breaking to generate the mediator bosons of (A, W + , W - , Z). Similarly, in SUSY, their superpartners ( \tilde{B} , \tilde{W}^{1} , \tilde{W}^{2} , \tilde{W}^{3} ) combine and produce neutral, colourless, weakly interacting particles, the neutralinos. Thanks to the R-parity, the lightest of the neutralinos is a stable particle which can disappear only by means of annihilation, a perfect WIMP candidate. It is possible to accommodate the WIMP hypothesis also in the EDi framework [ 9 ] . The basic idea behind EDi is to try to unify electromagnetism with gravity by introducing additional dimensions to reconcile the weakness of the gravity interaction with respect to the other forces. In this class of models, the strong and electroweak forces are confined in the 3+1 dimensions of the Universe, called brane . Instead, the gravitational force is described in a 3+1+ n dimension space named bulk , which embeds the brane, and thus appears feeble in the 3+1 brane. All of these extra dimensions are compactified on circles of size R , because if their dimension were big, they would have been detected [ 49 , 50 ] . The compactification forces all of the fields propagating in the bulk have their momentum quantised. The result is that for each bulk field, a set of Fourier expanded modes, called Kaluza–Klein (KK) states, appears. From the point of view of the four dimensional world, these KK states manifest as a series, tower , of states with masses m_{n}=n/R , where n labels the mode number. When the extra dimensions are small, it is possible for these fields to propagate throughout the bulk and not being confined only to the single brane. This is known as the Universal extra dimensions [ 51 ] . In these models, new particles coming from these KK states can be produced and the lightest ones have masses of the order of hundreds of GeV/c 2 [ 52 ] . Again, a theoretical model whose the main goal is solving known issues of the SM returns a perfect WIMP candidate. 1.2.3.2 Axions and ALPs The axions are particles predicted by an extension of the SM formulated by Peccei and Quinn [ 53 ] to tackle the strong CP problem. The Lagrangian of the Quantum ChromoDynamics (QCD) contains a term which causes the violation of the charge parity symmetry (CP). The parameter responsible for the intensity of the symmetry violation, \theta , is not constrained by any theoretical reason. Such CP violating term can give an arbitrarily large electric dipole moment to the neutron. Since no electric dipole moment for the neutron has ever been observed [ 54 ] , \theta has to be less than 10 -11 [ 55 ] . Nonetheless, the consequences of a CP violating term are not measured, leading to the necessity of a new symmetry which prevents the CP violation. The Peccei-Quinn solution is to introduce a U (1) chiral symmetry to prevent \theta from being \mathcal{O} (1). Similar to the Higgs potential, this symmetry is spontaneously broken at a scale f_{a} , leading to the generation of Goldstone bosons that carry the degrees of freedom. Specifically, the boson generated is a pseudo-Nambu-Goldstone boson which is called axion, a [ 56 ] . When the Lagrangian is rewritten in terms of this newly generated boson, the expectation value of the axion term is capable of compensating for the CP violating component of the QCD, solving the fine tuning issue. This also implies that the axion can couple to gluons and photons. In particular, the former allows to estimate the expected mass of the axion [ 57 ] as: m_{a}=5.70(6)\mu\text{eV}\left(\frac{10^{12}\text{GeV}}{f_{a}}\right) (1.20) connecting the mass of the particle to mixing strength with gluons. As a matter of fact, with a large enough f_{a} , the axion is stable and weakly interacting with matter, enough to be considered as a genuine DM candidate [ 58 ] . The axions are light, but being bosons, a group of them acting as a fluid can be demonstrated to recover all the relevant properties to explain the cold DM hypothesis [ 59 ] . The coupling with photons allows to thermally obtain the correct relic density, converting photons into axions in the early Universe [ 60 ] , or with an oscillation mechanism around the minimum of the potential [ 61 ] . Moreover, the coupling with photons permits different phenomena which can result in the destruction of an axion in favour of a SM particle, such as the axion decay in a couple of photons. This provides channels through which axion particles can be detected. Current constraints on the f_{a} parameter due to cosmological measurements are [ 62 ] : 10^{9}\text{GeV}\lesssim f_{a}\lesssim 10^{12}\text{GeV} (1.21) Theoretical frameworks which predict the existence of particles similar to axions have been elaborated. These models keep the coupling of these axion-like particles (ALPs) with photons, but relax the relation which binds f_{a} to its mass. Though these theories do not resolve the SM issues, these particles still have the characteristics to be a DM candidate. 1.2.3.3 Sterile neutrinos The SM predicts the existence of 3 types of neutrino with left handed chirality and zero mass. However, the observation of the oscillation of neutrino flavours implies that the neutrinos possess a mass [ 63 ] . A possible solution to the SM neutrino mass problem is found by introducing a new particle, the sterile neutrino. This is a singlet in the standard gauge group and thus it is interacting very weakly with SM matter only through a mixing mass matrix. Exploiting the seesaw mechanism, the mixing matrix between the sterile neutrino and the SM ones can be expressed as a symmetric matrix with one term much larger than the others. This causes the masses of the mixed neutrinos to be correlated so that when one is very large the other is very small. The tiny SM neutrino mass is explained by the high value of the mass of the sterile neutrino. If its mass is larger than \sim 1 keV/c 2 and the mixing angles of just mentioned mass matrix are small, it can be shown that it becomes non-relativistic early enough to produce a thermal relic density consistent with a cold DM hypothesis [ 64 ] . The coupling through the mixing mass matrix allows a tiny interaction between SM particles and the sterile neutrino. The extremely weak strength of mixing with the SM guarantees a stability which matches the requirements to be an example of a class of theories known as Feebly Interacting Massive Particles (FIMPs). In order to obtain the correct relic density with such small interaction the freeze in mechanism is preferred to the freeze out [ 65 ] . In this case the cross section of the interaction of DM with SM is so low that even at the early stages of the Universe DM is decoupled from the SM. The amount of DM is very small, but slowly increases by means of the annihilation of SM couples. The thermal relic density is reached when the production of DM is suppressed by the expansion of the Universe. The signature sought to look for these particles is the decay of the sterile neutrino in a monochromatic photon, on which research is still ongoing [ 66 ] . 1.2.3.4 Dark sector In the context of DM searches, numerous models in the direction of a dark sector have become popular. In these frameworks, the SM is just one sector of the particles and forces present in the Universe, next to which a dark sector composed by a collection of particles that are not charged directly under the SM strong, weak, or electromagnetic forces exists. The dark sector can contain from few particles up to entire new interaction forces and structure similar to the SM one. The dark sector scenario is well motivated by the ease with which SM limitations can be overcome [ 67 , 36 ] . Particles belonging to this sector are assumed to interact gravitationally, but may also possess a messenger sector, called portal , which contains one or more states that mediate SM–dark sector interactions. The gravitational interaction along with the suppression of strong or electromagnetic interaction make the dark sector particles optimal DM candidates [ 68 ] , whose relic density can be thermally obtained both via freeze out and freeze in scenarios [ 67 ] . One of the most renowned class of dark sector models is the dark photon portal in which a light thermal WIMP, in the MeV/c 2 mass range, interacts with the SM sector via a dark photon (a dark sector gauge boson) which mixes with the SM photon. The dark photon can be detected because of its kinetic mixing with the ordinary, visible photon. This kinetic mixing is always possible because the field strengths of two Abelian gauge fields can be multiplied together to give a dimension four operator. The existence of such an operator means that the two gauge bosons can go into each other as they propagate. This kinetic mixing provides the portal linking the dark and visible sectors [ 68 ] . The generic Lagrangian of these models includes a kinetic term of the dark photon: \mathcal{L}_{0}=-\frac{1}{4}F_{a\mu\nu}F_{a}^{\mu\nu}-\frac{1}{4}F_{b\mu\nu}F_{b}^{\mu\nu}-\frac{\epsilon}{2}F_{a\mu\nu}F_{b}^{\mu\nu} (1.22) where a and b denote respectively the dark and the SM photon components, while the last block is the kinetic mixing of the two gauge bosons. In some cases the dark photon can be a massless gauge boson and the DM is identified with GeV/c 2 or TeV/c 2 scale dark fermions [ 69 ] , in some other the dark photon is massive and light (MeV/c 2 scale) and it is the DM candidate itself [ 70 ] . The portal a dark sector exploits to interact with the SM can also be modelled employing dark fermions in place of dark photons [ 71 ] . A generic dark fermion term can be added to a Lagrangian as follows: \mathcal{L}=eJ_{\mu}A_{b}^{\mu}+e^{\prime}J_{\mu}^{{}^{\prime}}A_{b}^{{}^{\prime}\mu} (1.23) with the ′ indicating the dark sector terms. Possible constraints can be found in the analyses of the BBN, in the structure formation theory, but are also sought at accelerators experiments [ 68 ] . Chapter 2 Direct detection of dark matter As illustrated in Chapter 1 , astronomical and cosmological measurements indicate that the description of the fundamental particles and forces of the Universe is still incomplete. All the unexplained observed effects are compatible with a missing mass problem. In the assumption that dark matter (DM) is composed by particles which can couple to Standard Model (SM) ones not only gravitationally (see Section 1.2.3 ), this interaction can be exploited in different ways to search for DM signatures. DM can be indirectly probed by studying potential unexplained excesses of SM particles produced by DM annihilation in space. Unpredicted fluxes of SM particles from space, like positrons, antiprotons or \gamma s, are looked for by dedicated detectors [ 72 ] . Alternatively, the ability to create new particles, typical of experiments at high energy colliders, can be employed to search for DM signature either in direct production [ 73 ] or via beam dump approaches [ 74 ] . The direct DM detection techniques discussed in this thesis aim at observing the elastic scatters of Galactic DM particles with the detector material. The measurements of the rotation curve of the Milky Way imply, in fact, that the Galaxy is embedded in a DM halo, like all spiral galaxies (see Subsection 1.1.1 ). The peculiar motion of the Earth and Sun with respect to the centre of the Galaxy imprints a preferred direction of arrival of these DM particles with respect to the laboratory rest frame, which can be exploited to measure and characterise DM interactions. Unfortunately, astrophysical constraints imply that the coupling between DM and SM particles is very weak, making the expected signal rate very low. Given the large number of phenomena able to produce interactions that can mimic a DM signal, direct DM searches are experimentally extremely challenging. This thesis, from now on, will address specifically the direct detection of WIMPs through nuclear recoil signatures, and refers the reader to [ 72 , 73 , 75 ] for a recent comprehensive review of all other approaches. In Section 2.1 , the phenomenology of the WIMP interaction for the direct detection is described. In Section 2.2 , a summary of the working principles of the direct detectors for DM is presented. Finally, Section 2.3 discusses the features and advantages of the directional detection. 2.1 WIMPs-nuclei scattering In the WIMP assumption, the Milky Way resides in a halo composed of these cold , non relativistic, DM particles. The peculiar motion of the Sun around the centre of the Galaxy, along with the rotation of the Earth around the Sun, produces an apparent wind of DM particles coming from a preferential direction. This phenomenon boosts the energy of these DM particles from Earth’s frame of reference and fosters the possibility of detectable interaction between WIMPs and SM particles, in the assumption of the existence of an interaction between the two. The core idea of a direct detection experiment is to position a volume of material able to measure recoils of regular matter after a WIMP interaction occurs. The most common SM constituents available in a material are electrons and nuclei. DM can potentially interact with both of them, but large focus is on the nuclear scatter. Indeed, as WIMPs are expected to possess a mass of \mathcal{O} (10) GeV/c 2 , a better kinematic coupling is foreseen for nuclei than electrons. It should also be noted that electron recoils can be more easily generated by other interactions, such as \gamma rays with electrons, than nuclear recoils. 2.1.1 Expected event rate Following [ 76 , 77 , 78 ] , the expected rate per unit mass for an interaction between Galactic WIMPs and atomic nuclei can be defined as: dR=\frac{N_{0}}{A_{mol}}\sigma v\frac{\rho_{0}}{m_{\chi}}f(\vec{v})d^{3}v, (2.1) with N_{0} the Avogadro number, \rho_{0} the DM density at Earth, A_{mol} the molar mass of the atom, \sigma the cross section between the WIMP and the nucleus, m_{\chi} the mass of the WIMP, and f(\vec{v}) the distribution of the velocities of the WIMPs in the Galactic Rest Frame, with the Galactic Rest Frame being the reference frame in which the Galactic centre is at rest. The differential rate in the recoiling nucleus momentum q and solid angle \Omega can then be obtained by integrating on all the possible velocities which can induce detectable signatures on the detector as: \frac{dR}{dq^{2}d\Omega}=\frac{N_{0}}{A_{mol}}\frac{\rho_{0}}{m_{\chi}}\int_{v_{min}(q)}\frac{d\sigma}{dq^{2}d\Omega}vf(\vec{v})d^{3}v (2.2) where the integral is performed on the domain of the velocity distribution of the DM particles above the minimum velocity, v_{min} , which is required to induce a recoil of momentum q . Equation 2.2 explicitly highlights how predicted rates assume a certain mass and scattering cross section, as well as a set of astrophysical parameters, material target and experimental performances. Each of these will be discussed in details in the following. 2.1.2 DM halo The DM halo of the Milky Way is usually described by the Standard Halo Model (SHM) [ 79 ] . The SHM assumes an isotropic, isothermal sphere of DM particles with a density profile of \rho(r)\propto r^{-2} . Under the assumption of collisionless particles and isothermal system, the velocity density distribution can be expressed as a Maxwell-Boltzmann distribution: f(\vec{v})=\begin{cases}\alpha e^{-\frac{v^{2}}{v_{p}^{2}}}&\text{if }|\vec{v}|v_{esc}\\ \end{cases} (2.3) with \alpha the normalisation factor and v_{p} the most probable value of the velocity distribution close to the Earth and also represents the velocity dispersion of the WIMPs. When assuming a perfectly flat rotation curve for the Galaxy, v_{p} can be measured at various distances and is found to be about 230 km/s at the Earth radius [ 80 , 81 , 82 ] . Yet, more precise calculations of the rotation curve predict a non perfectly flat Milky Way and, depending on its modelling, systematic uncertainties on the v_{p} arise leading to a value span from 200 up to 279 km/s [ 83 ] . While the Boltzmann distribution of the velocity extends mathematically up to infinity, extremely fast particles are bound to leave the Galaxy and escape, effectively posing an upper limit on the available velocities for WIMPs detection. In the SHM, this is implemented by manually truncating the velocity distribution at the local escape speed v_{esc} . This varies according to the distance R from the centre of the Galaxy, following the amount of matter inside R . At the Solar position, 8.2 kpc from the centre, and assuming a smooth halo in equilibrium, the escape velocity v_{esc} is measured by the Gaia telescope and RAVE survey [ 84 , 85 ] and it is taken as 544 km/s. Another interesting astrophysical parameter is the DM density at the Solar distance from the centre of the Galaxy, \rho_{0} . Despite some systematic uncertainties, the most commonly used value is 0.3 GeV cm -3 c -2 [ 80 ] . Recent measurements which followed the hypotheses of the Frenk Navarro White density profiles [ 86 ] set constraints on the \rho_{0} at slightly higher values, about 0.4 GeV cm -3 c -2 . Other local estimations which do not require mass-modelling of the Milky Way [ 87 ] , are in agreement with 0.3 GeV cm -3 c -2 , but with large uncertainties. In the WIMP theoretical framework, the DM is cold, non relativistic. As a consequence, the speed of the DM particles is comparable to the peculiar velocity of the Sun and the Earth. For this to be taken into account when calculating the expected rate of interaction of WIMPs with SM particles on Earth, a coordinate transformation is needed. A Galilean transformation is sufficient because the velocities are well below the relativistic limit, and the gravitational potential of the Sun and the Earth are weak enough to affect only WIMPs with less than 40 km/s [ 88 ] , which represent a very small fraction. In this transformation of coordinates, the laboratory velocity v_{lab} is the sum of the Sun’s velocity with respect to the Galactic Rest Frame and Earth’s motion around the Sun. In some cases, the direct detector is approximated as positioned in the centre of the Sun, neglecting Earth’s motion. While this is limiting for phenomena in the context of annual (see Section 2.1.5.2 ) and daily modulation searches, it does not affect the recoil distribution or the rate above few percents [ 89 , 83 ] . When only the peculiar velocity of the Sun is taken into account when evaluating the laboratory velocity v_{lab} , it is valid that v_{lab}=242 km/s [ 80 ] . The SHM may not be the best approximation of the DM halo of the Milky Way as the isothermal and isotropic hypotheses are widely considered too simplistic. In cold DM cosmologies, structures form hierarchically, leading to DM halos which are triaxial, anisotropic and contain phase-space substructure [ 90 ] . The correct estimation of the DM halo is still debated with measurements and various simulation pointing at different structures and velocity distributions [ 91 , 92 , 93 , 94 ] . While the SHM might not be the best modelling of the real DM distribution of WIMPs, it is generally used as benchmark for the computation of the WIMPs rate of interaction with SM particles in the direct detection context. The guidelines for the astrophysical quantities regarding the halo model can be found in [ 80 ] . 2.1.3 WIMP-nucleon elastic cross section The type and model of interaction between the WIMPs and SM matter is unknown, hence an operative approximation can be performed by employing the Fermi’s Golden rule. Thus, the factor \frac{d\sigma}{dq^{2}} can be approximated splitting the dependence on the energy of the differential cross section in an independent term \sigma_{WA} and another one, S(q) , which includes the entire dependence on the transfer momentum q , the form factor (which will be discussed later). \frac{d\sigma}{dq^{2}}=\frac{1}{\pi v^{2}}|\mathcal{M}|^{2}=\frac{\sigma_{WA}S(q)}{4\mu_{A}^{2}v^{2}} (2.4) where \mu_{A} is the reduced mass of the nucleus A and the WIMP \chi , defined as: \mu_{A}=\left(\frac{m_{\chi}m_{A}}{m_{\chi}+m_{A}}\right) (2.5) The nuclei present in common materials only posses thermal energy and are non relativistic. At the same time, the SHM and the cold DM hypothesis need the WIMPs to be non-relativistic particles. With the peak of the local WIMP velocity being \sim 230 km/s, the De Broglie wavelength associated to the DM particle of roughly 10 GeV/c 2 mass is: \lambda_{DM}=\frac{h}{p}\sim 160fm (2.6) On the other hand, the typical nuclear dimension is of the order of few fm, at least one order of magnitude less than the \lambda_{DM} . As a consequence, it is possible to assume that the WIMP perceives the nucleus as a whole and interacts with it coherently. Moreover, due to the small expected energy transfers the scattering is considered elastic. While the actual nature of DM coupling is not known, it is possible to make a simplified standard assumption that it can possess spin-independent (SI) and spin-dependent (SD) interactions, which couple to the charge, the mass and spin of the nucleus, respectively. From this and [ 95 ] , it is possible to write a generic expression of the cross section as: \sigma_{WA}=\sigma_{WA,SI}+\sigma_{WA,SD} (2.7) The SI term can be parameterised as a function of the target nature as: \sigma_{WA}=\frac{4\mu_{A}^{2}}{\pi}\left[Zf_{p}+(A-Z)f_{n}\right]^{2} (2.8) Here f_{p} and f_{n} are the effective spin independent couplings to the proton ( p ) and neutron ( n ), while A and Z are the atomic mass and number of the nucleus. A reasonable assumption, supported by various models, is that WIMPs have the same coupling to proton and neutrons, resulting in f_{p} = f_{n} . Thus: \sigma_{WA,SI}\simeq\frac{4\mu_{A}^{2}}{\pi}A^{2}f_{n}^{2}=\sigma_{n,SI}\frac{\mu_{A}^{2}}{\mu_{n}^{2}}A^{2}, (2.9) with \mu_{n} the reduced mass of m_{\chi} with the mass of a nucleon. This way, the cross section with a generic nucleus can be expressed as a function of the cross section with a nucleon \sigma_{n,SI} . The Equation also shows that the SI cross section is enhanced by a factor A^{2} , favouring heavy nuclei. This is consistent with the expectation of a coherent scattering where the contribution from all the nucleons are summed up together. The SD cross section can be expressed as: \sigma_{WA,SD}=\frac{32G_{F}^{2}\mu_{A}^{2}}{\pi}\frac{J+1}{J}\left(a_{p}\left\langle S_{p}\right\rangle+a_{n}\left\langle S_{n}\right\rangle\right) (2.10) with a_{p} and a_{n} the effective spin dependent couplings to the proton ( p ) and neutron ( n ), J the nuclear spin, while \left\langle S_{p}\right\rangle (and \left\langle S_{n}\right\rangle ) is the expectation value of proton (neutron) spin inside the nucleus. The cross section strongly depends on the spin state of the nucleus. An asymmetry in the number of protons or neutrons is required to have a large expectation value of spin and therefore sensitivity to SD interaction, as the contributions of the different nucleons generally cancel out [ 96 ] . Table 2.1 summarises some of the elements with largest expected spin value, extracted from [ 96 ] . Each of these nuclei is sensitive mainly to proton or neutron interaction depending on the which nucleon is odd in the nuclear structure. Nucleus Z Odd Nuc. J \left\langle S_{p}\right\rangle^{2} \left\langle S_{n}\right\rangle \frac{4\left\langle S_{p}\right\rangle(J+1)}{3J} \frac{4\left\langle S_{n}\right\rangle(J+1)}{3J} 1 H 1 p 1/2 0.500 0.0 1.0 0 19 F 9 p 1/2 0.447 -0.004 9.1 \times 10^{-1} 6.4 \times 10^{-5} 73 Ge 32 n 9/2 0.030 0.378 1.5 \times 10^{-3} 2.3 \times 10^{-1} 129 Xe 54 n 1/2 0.028 0.359 3.1 \times 10^{-3} 5.2 \times 10^{-1} Table 2.1: Table taken from [ 96 ] summarising the spin nuclear characteristic of few of the most relevant nuclei in regards to the sensitivity to the SD interaction. As reported in [ 78 ] , the SD cross section to proton and to neutron can be defined as: \sigma_{p,SD}=\frac{24G_{F}^{2}\mu_{p}^{2}a_{p}^{2}}{\pi} (2.11) \sigma_{n,SD}=\frac{24G_{F}^{2}\mu_{n}^{2}a_{n}^{2}}{\pi}. Now, combining Equations 2.7 , 2.9 , 2.10 and 2.11 , the total cross section for a nucleus containing an odd number of protons can be written as: \sigma_{WA}=\sigma_{n,SI}\frac{\mu_{A}^{2}}{\mu_{p}^{2}}A^{2}+\sigma_{p,SD}\frac{\mu_{A}^{2}}{\mu_{p}^{2}}\frac{4\left\langle S_{p}\right\rangle^{2}(J+1)}{3J} (2.12) With respect to Equation 2.12 , it is possible to notice that the SD term \frac{4\left\langle S_{p}\right\rangle(J+1)}{3J} , generally less than 1, is much smaller than the SI term. Thus, in case the \sigma_{n,SI} is of the same order as \sigma_{p,SD} , for the majority of the targets the SI interaction dominates, and the SD component becomes negligible. For this reason, the experiments which set limits on the WIMP to nucleon cross section separate the SI scenario from the SD one. As a convention, the DM limit plots are put on the parameter space generated by \sigma_{n,SI} and m_{\chi} for the SI, whilst on \sigma_{p,SD} ( \sigma_{n,SD} ) and m_{\chi} for the SD coupling to the proton (neutron). 2.1.3.1 Form factor S(q) is the nuclear form factor which carries the dependence of the differential cross section on the momentum transfer of the collision, and it depends on the structural form of the nucleus treated in the Fermi’s approximation. This describes the nucleus in a spherical symmetry with a radius R_{n} and a skin thickness [ 78 ] . The form factor for the SI takes into account the fact that with larger momentum transfers the nucleus appears less and less homogeneous and the interaction loses coherence. It can be evaluated as the Fourier transformation of the nucleus radius function found in [ 76 ] and results in: S(q)=|F(q)|^{2}=\biggr\rvert\frac{9[\sin(qR_{n})+qR_{n}\cos(qR_{n})]^{2}}{(qR_{n})^{6}}\biggr\rvert^{2} (2.13) with the radius of the nucleus approximated as: R_{n}\simeq\left[0.91A^{1/3}+0.3\right]fm. (2.14) The form factor for SD interactions embeds corrections due to the spin structure function, and thus its calculation results much more complex [ 78 ] . Nonetheless, at first order it can be expressed as: S(q)=|F(q)|^{2}=\biggr\rvert\frac{\sin(qR_{n})}{qR_{n}}\biggr\rvert^{2}. (2.15) 2.1.4 Kinematic Figure 2.1: Schematics of the scatter between a DM particle \chi with momentum p_{0} and a nucleus A at rest. The nucleus scatters with momentum q at an angle \theta . The kinematics of the elastic scattering between two particles can be evaluated in general terms as a relativistic collision. Under the SHM assumption, WIMPs are expected to have an average velocity of the order of 10 -3 c, whilst the thermal energy of a nucleus of a \mathcal{O} (10) GeV/c 2 at 300 K is about 10 -5 c. Therefore, as displayed in Figure 2.1 , it is reasonable to consider a DM particle \chi with a momentum p_{0} and velocity v which collides with a nucleus A at rest. The latter recoils with momentum q at an angle \theta as a result of the elastic collision. The laws of conservation of energy and momentum require that: P_{0}^{\mu}+Q_{0}^{\mu}=P^{\prime\mu}+Q^{\mu} (2.16) The 3-dimensional momentum q of the recoiling nucleus can be evaluated in natural units as: q=\frac{2m_{A}(\sqrt{p_{0}^{2}+m_{\chi}^{2}}+m_{A})p_{0}\cos\theta}{(\sqrt{p_{0}^{2}+m_{\chi}^{2}}+m_{A})^{2}-p_{0}^{2}\cos^{2}\theta}. (2.17) Given the non-relativistic nature of the particles involved in the WIMPs to nuclei scattering, the following approximation is valid m_{\chi},m_{A}>>p_{0} . Thus, Equation 2.17 can be reduced to: q=2v\mu_{A}\cos\theta, (2.18) Since the expected WIMP mass spans over several orders of magnitude, the efficiency in transfer momentum to the nucleus depends on the masses of the two particles. The maximum energy the recoil can attain is: E_{max}=\frac{q_{max}^{2}}{2m_{A}}=\frac{2\mu_{A}^{2}v^{2}}{m_{A}}\equiv r\frac{1}{2}m_{\chi}v^{2}, (2.19) where r is the adimensional efficiency in the momentum transfer defined as r=4\frac{m_{\chi}m_{A}}{(m_{\chi}+m_{A})^{2}}. (2.20) When m_{A}=m_{\chi} , the efficiency is maximal, r=1 . This shows how the maximal sensitivity of a given target is for WIMPs of the same mass of the atoms composing the target. For instance, to optimise the sensitivity to WIMP masses close to 1 GeV/c 2 , light targets as helium or hydrogen represent the best choices. Another relevant relation, is the minimum velocity a WIMP needs to have in order to cause a recoil of energy E . Indeed, relative to the angle \theta of scattering, the same E can be induced by different v of a DM particle. The minimum velocity required to impinge a recoil energy E is: v_{min}=\frac{\sqrt{2Em_{A}}}{2\mu_{A}}. (2.21) 2.1.5 Experimental signatures Combining the expression derived in the Subsection 2.1.4 , which binds the angle of the recoil to its energy, with Equation 2.2 , one obtains: \frac{dR}{dq^{2}d\Omega}=\frac{N_{0}}{A_{mol}}\frac{\rho_{0}}{m_{\chi}}\frac{d\sigma}{dq^{2}}\frac{1}{2\pi}\int\delta\left(\cos\theta-\frac{q}{2\mu_{A}v}\right)vf(\vec{v})d^{3}v, (2.22) This way, the double differential cross section is expressed in terms of the differential cross section on momentum, while the dependence on the angular part is made explicit in the Dirac’s delta. Introducing the expression for the SI cross section discussed in Subsection 2.1.3 , the expected rate for SI interactions per unit of mass for a mono-atomic molecule becomes: \frac{dR}{dEd\Omega}=\frac{2N_{0}}{A_{mol}}\frac{\rho_{0}\sigma_{n,SI}S(E)}{m_{\chi}^{2}r}\frac{\mu_{A}^{2}}{\mu_{n}^{2}}A^{2}\frac{1}{2\pi}\int\delta\left(\cos\theta-\frac{q}{2\mu_{A}v}\right)\frac{f(\vec{v})}{v}d^{3}v. (2.23) It is now useful to define the integral on the velocity distribution, which is independent on the type of interaction between WIMP and nucleus, as: I=\frac{1}{2\pi}\int\delta\left(\cos\theta-\frac{q}{2\mu_{A}v}\right)\frac{f(\vec{v})}{v}d^{3}v. (2.24) A possible method to solve the integral of Equation 2.24 is to rely on the Radon transform [ 76 , 97 , 98 ] , that takes into account the proper coordinate transformation to express the Equation 2.23 in the laboratory rest frame. The velocity employed for the change of reference frame is \vec{v}_{lab}=-v_{lab}\hat{u_{z}} , with \hat{u_{z}} defined in the opposite direction of the motion of the laboratory in the Galactic rest frame. Following the calculation in Appendix A , the double differential cross section for a WIMP scattering as a function of the recoil energy E and the angle \gamma between the recoil direction and \vec{v}_{lab} can be expressed as: \displaystyle\frac{dR(t)}{dEd\cos\gamma} \displaystyle=\frac{N_{0}}{A_{mol}}\frac{2\rho_{0}\sigma_{n,SI}S(E)}{m_{\chi}^{2}r}\frac{\mu_{A}^{2}}{\mu_{n}^{2}}A^{2}\pi\frac{v_{p}^{3}}{v_{lab}(t)}\alpha^{\prime}\times (2.25) \displaystyle\times\left(e^{-\frac{\left(\frac{\sqrt{2m_{A}E}}{2\mu_{A}}-v_{lab}(t)\cos\gamma\right)^{2}}{v_{p}^{2}}}-e^{-\frac{v_{esc}^{2}}{v_{p}^{2}}}\right) \displaystyle\Theta\left(\cos\gamma-\frac{\frac{\sqrt{2m_{A}E}}{2\mu_{A}}-v_{esc}}{v_{lab}(t)}\right), with \alpha^{\prime} the normalisation factor of the velocity distribution, and where a dependence on the time t has been added to the v_{lab} as it includes the component of the Earth’s velocity. The role of v_{esc} is critical as it basically limits the integral for large velocities, indirectly restricting the energy a recoil can possess. Indeed, for each DM mass, there is a maximum energy E_{max} which can be induced to the nucleus A when a WIMP is at the maximum velocity allowed: E_{max}=\frac{1}{2}m_{\chi}r(v_{lab}(t)\cos\gamma+v_{esc})^{2} (2.26) This Equation shows explicitly how the energy threshold of an experiment effectively limits the mass parameter space that can be studied depending on the mass of the target, as a m_{\chi} will be undetectable if E_{max} is below the threshold. Overall, the differential rate is a function of three variables which can be experimentally measured: recoiling energy E , time t , and angle of scatter \gamma . 2.1.5.1 Recoil rate energy dependence Figure 2.2: The energetic recoil spectra of a Ge target for different WIMP masses, taken from [ 78 ] . With lower WIMP mass the spectrum is sharply cut at high energies due to the escape velocity effect on the recoil maximum energy. The expected energy spectrum of WIMP induced nuclear recoil, as a function of the WIMP mass, is obtained from Equation 2.25 by averaging on time the v_{lab} and integrating over the \cos\gamma domain from -1 to 1. The spectrum is limited at high energies by the E_{max} and in intensity by the dumping effect of the form factor, especially for large A targets. The energy distribution is constrained at low values by the energy threshold E_{thr} which depends on the characteristics of the specific detector employed for the direct search. At first order of approximation, the energy spectra have a falling exponential behaviour without any particular feature nor peak. Figure 2.2 from [ 78 ] shows examples of the energetic recoil spectra of a Ge target for different WIMP masses. The effect of the escape velocity on the spectrum is highly visible as with lower WIMP mass it results sharply cut at high energies. 2.1.5.2 Recoil rate temporal dependence The motion of the Earth around the Sun modifies the relative velocity of WIMPs with respect to the target nuclei during the year. In December, in the northern hemisphere, Earth’s orbital velocity has a component anti-parallel to the motion of the Sun around the Galactic centre, and parallel during June. This effectively induces a temporal dependence in the expected interaction rate of a few percent over one year, since the orbital velocity about 30 km/s. Thus, a diverse strategy to seek for WIMP signature is to exploit this annual modulation, which can be expressed as [ 99 ] : \frac{dR}{dE}\simeq R_{0}+R_{m}\cos(\omega(t-t_{0})) (2.27) where the differential rate depends on the time averaged signal R_{0} and the modulated one R_{m} whose dependence on time is expressed by a sinusoidal function of frequency \omega=2\pi/ year and by the phase of the modulation t_{0} . The observation of an annual modulation of the nuclear recoil rate in the detector could therefore be used to test the DM hypothesis. In order be sensitive to this signature, an experiment needs a large exposure with a highly stability in the response over an \mathcal{O} (1) year of time. 2.1.5.3 Recoil rate angular dependence Earth’s co-motion with the Sun introduces a directional dependence of the rate, that peaks in the mean radial direction of the Sun (or else roughly towards the Cygnus constellation), with a diurnal temporal modulation due Earth’s rotation around its own axis. The angular spectrum of the recoils can be obtained by averaging on time the \vec{v}_{lab} and integrating over all the range of energies \left[E_{thr},E_{max}\right] . From Equation 2.25 , the most relevant term for the angular dependence can be extracted: \frac{dR}{d\cos\gamma}\propto\int_{E_{thr}}^{E_{max}}e^{-\frac{\left(v_{lab}\cos\gamma-v_{min}\right)^{2}}{v_{p}^{2}}}, (2.28) Figure 2.3: Examples of angular distribution of the recoils induced by WIMP interaction calculated following the SHM assumptions (for more details see Section 7.2 ). On the left, the distribution is evaluated using a WIMP mass of 10 GeV/c 2 on fluorine target which exhibits the typical dipole structure. On the right, the WIMP mass used is 100 GeV/c 2 with xenon target. In this case the recoil follow the ring-like shape due to the masses combination. where the dependence of the exponential on the \cos\gamma remarks the anisotropic nature of the angular distribution of the recoils, which is clear once displayed in Galactic coordinates. The Galactic coordinate system is a right-handed celestial coordinate system in spherical coordinates centred on the Sun. The x-axis points at the centre of the Milky Way, while the y-axis approximately is parallel to the peculiar motion of the Sun with respect to the Galactic Rest Frame. This way, the Galactic plane corresponds to the equatorial plane of the coordinate system. The coordinates employed are the Galactic longitude l and the Galactic latitude b , whose behaviour mirrors the one of terrestrial longitude and latitude. In this coordinate system, the constellation of Cygnus is located at (l,b)\simeq(81,0.5) . Examples of the angular distribution of recoils in Galactic coordinates are shown in Figure 2.3 (for more details on the plot assumptions, see Section 7.2 ). These clearly display the anisotropic nature of the angular distribution of WIMP-induced recoils, with an excess of events at negative longitude, opposite to the motion of the Sun. This signature present a directional correlation with an astrophysical source that no background whatsoever can mimic (also thanks to the rotation of Earth’s rotation around its own axis) and can hence offer the possibility for a positive claim of a DM signal. A more detailed description of the features of the angular distribution of the recoils, along with the advantages of the directional search will be presented in Section 2.3 . 2.2 Experimental challenges and detection techniques The direct detection experiments search for signatures which are induced by a DM interaction. A comprehensive report of the direct detection approach and status can be found in [ 36 ] . Taking into account the kinematic at play and the constraints from Equation 2.26 , the expected recoil energies for WIMP interactions are of the order of few keV, while the rate, estimated from Equation 2.25 and current limits, is foreseen to be below the \mathcal{O} (1) event kg -1 y -1 , making the direct detection a search for very rare events. In addition, many sources of backgrounds can mimic DM induced signal, further complicating its quest. Cosmic rays and natural environmental and material radioactivity produces electromagnetic radiation with rates typically 10 6 -10 8 or more times larger than an expected WIMP signals, and need therefore to be properly passively shielded or actively suppressed in the analysis. Neutrons and neutrinos from ambient and space, moreover, induce a detector response nearly identical to WIMPs, unless some additional topology or directional handle is employed for further discrimination. Direct DM searches experimental techniques are based on the possibility of measuring the energy deposited by a particle interacting with the instrumented target material in the form of ionisation, scintillation or lattice vibrations (i.e. heat). Most of the experiments measure more than one of these channels, a feature that allows to distinguish an electron recoil (ER) from a nuclear recoil (NR), due to the different energy release mechanism of such particles. In large detectors with heavy dense targets, fast neutrons with \mathcal{O} (1) cm mean free path can be suppressed by looking for multiple scatterings or defining an internal fiducial volume, at the price of reducing the active material sometimes even by 50%. Neutrinos, conversely, can not be effectively shielded and can induce NRs by means of coherent scattering with nuclei (CE \nu NS) [ 100 ] with an energy spectrum very similar to NRs expected from WIMP interaction. As a consequence, the knowledge of the backgrounds and its minimisation are of the utmost importance for the success of a direct DM experiment. Ideally, an experiment aims at the complete suppression of any form of interaction that could resemble a DM signal, by either minimising the possible sources or by actively suppressing this contribution in the experiment setup or analysis. Therefore, their goal is to meticulously detail the typical features of background events in order to be able to properly account for their contribution at the analysis stage. 2.2.1 Background sources The rare nature of WIMP induced recoils requires the detector to be in a controlled environment where these key signatures of DM interaction can be efficiently detected. The flux of secondary cosmic rays coming from the interaction of high energetic nuclei from outer space in the atmosphere can be as high as \sim 100 particles per m 2 per s. This stream is for the majority composed of muons with energies ranging from MeV up to hundreds of GeV, which represent a quite penetrating radiation. Immense shielding facilities would be required to suppress this form of background. As a consequence, all the direct detection experiments are located in underground laboratories, below at least hundreds of metres of rock to strongly suppress the cosmic flux and reduce this background. Typically the underground facilities are tunnels dug in mountains or mines. Some examples are the Laboratori Nazionali del Gran Sasso (LNGS), and the Boulby mine among others. Underground facilities, while protected from cosmic rays, present nonetheless a natural environmental radioactivity produced by the surrounding rocks. The radioactive chains of thorium and uranium are present in almost every rock including the natural bed of rocks of the underground sites. These chains include a wide variety of elements and due to the secular equilibrium, even the isotopes with very short half-life are important contributors. Among them, the largest contributions come from 238 U, 234 Th, 232 Th, 226 Rn, 214 Pb, 214 Bi, 227 Ac, 220 Rn, 212 Pb, and 212 Bi. In addition, also the 40 K is a radioactive element often present, especially when human activity is involved. These isotopes can decay in diverse ways with the emission of alpha particles, electrons, positrons or \gamma s. Alphas, positrons and electrons can be more easily stopped, as their energy loss is continuous, and generally do not exit from the rock itself. However, \gamma s, mostly coming from the de-excitation of a nucleus after a radioactive decay, can cross the rock unaffected and reach the active volume of an experiments, where they induce ERs. Figure 2.4 on the left panel shows a measurements of the gamma induced background above ground and in two underground sites. A difference in the environmental gamma spectrum is visible and is due to the different rock composition of the two laboratories, Dolomite calcareous rock for the LNGS and salt and potash for the Boulby mine. Figure 2.4: On the left, the \gamma spectrum above ground and in two underground sites as a function of energy. On the right, the LNGS underground environmental neutron flux [ 101 ] . A non negligible amount of neutrons can also be emitted by natural rocks which can induce NRs. The origin of the emission of these neutrons can be separated in two categories: radiogenic, when caused by radioactivity, and cosmogenic, when induced by muons. In the former case, they can be emitted following a natural fission for very high A elements, or by means of an ( \alpha ,n) reaction, when an alpha particle interacts with a high Z material with the resulting emission of a neutron [ 102 ] . The cosmogenic neutrons instead are produced by spallation processes subsequent to a muon collision [ 103 ] . To suppress the amount of radiation that reaches the sensitive part of the detectors, underground experiments are also equipped with shielding material. The shields can be passive, when it is used merely for its stopping power properties, or active, when it is instrumented and signals can be obtained from the energy deposited in the shield material to characterise the external background and actively suppress it through vetos. Copper and lead are often used as passive shielding with high Z to stop \gamma s and \beta s, whilst materials rich in hydrogen, such as water or polyethylene, are employed to slow down and absorb neutrons thanks to the large kinematic match with H. In addition, scintillators instrumented with photon detectors and water Cherenkov detectors are possible solutions for active shielding configurations [ 104 ] . Electromagnetic and neutral backgrounds can also come from the material the shielding and the detector themselves are manufactured with, and for this reason, they are typically called internal backgrounds. As this is much harder to block due to the vicinity to the sensitive volume, the best approach is to suppress it as much as possible enhancing the radiopurity of the materials employed [ 105 ] . Along with the same 40 K and the chains of 238 U, 235 U and 232 Th (which are always present as contaminants), other typical contaminating isotopes are 60 Co, 57 Co, 58 Co and 54 Mn from the activation of the copper and iron utilised as shielding and structural materials due to muon-induced neutrons interactions [ 106 ] . Background can also come from the progeny of radon deposited on the internal structure of the detector. 222 Rn is a radionuclide which belongs to the 238 U chain and is an inert gas. As a consequence, radon can escape the rocks and be present in the air of the underground facility, from which it can easily penetrate inside the experiment structure, even in the internal layers close to the sensitive volume. When radon decays into 218 Po, the unstable positively charged ion 218 Po + (80% of times) is sensitive to electric fields and can therefore deposit on detector electrodes and decay with the emission of alphas. The geometry of this process implies a high probability for the alpha to be completely embedded in the detector material, leaving only the 218 Po recoiling in the fiducial volume and mimicking a WIMP interaction. In order to reject these events, the full 3D position of the events needs to be reconstructed (a technique usually referred to as “fiducialisation”), something not necessarily trivial for experiments in the DM search field, since the absolute time of interaction is not always known. Figure 2.5: Neutrino energy spectrum at Earth, integrated over directions and summed over flavours for energies above 100 keV. Figure taken from [ 107 ] . Neutrinos emitted by the Sun, produced in the atmosphere by cosmic rays and coming from the diffuse flux of the Supernovae are a critical sources of background [ 107 ] . Figure 2.5 shows the energy spectrum of the neutrinos from these different astrophysical sources. The energies and fluxes span over several orders of magnitude. The most intense are the ones coming from the Sun, especially from the pp cycle, which mostly induce ERs of the order of few keV, and 8 B chains, which generate NRs of the same energies, impossible to be singularly discriminated from WIMP induced ones. Relevant contributions in form of NRs also come from the atmospheric flux. Current Xe-based experiments (and several next generation detectors) are starting to be sensitive to the 8 B solar component [ 108 ] . Experiments at the \mathcal{O} (1) tonne scale are reaching a sensitivity at which Solar neutrinos are bound to affect the improvements in the cross section-WIMP mass limit phase space. This makes the realisation and construction of larger detectors with the goal of improving the sensitivity for DM highly problematic and not convenient. In the past years, this has been considered a nearly hard limit (hence denominated Neutrino Floor ) where DM signals become hidden underneath a remarkably similar-looking NR background, unless a very large statistic (possibly with multiple targets) [ 107 ] or directional information [ 83 , 109 ] are employed. A more recent approach [ 110 ] , already well accepted by the international community [ 111 ] , has refined this definition from a floor to a fog , that is interpreted as: "A region of the parameter space where a clear distinction between signal and background is challenging, but not impossible [ 110 ] ." Figure 2.6: The neutrino fog of xenon shown along with some experimental limits on the SI WIMP to nucleon cross section. The colour intensity represents the n index of logarithmic proportionality between the limits on the cross section and the number of CE \nu NS events detected. Figure extracted from [ 110 ] . The new definition is based on the derivative of the discovery limit \sigma . This technique makes the Neutrino Fog definition independent from the experimental exposure and energy threshold and highlights how the uncertainties of the various neutrino fluxes of Figure 2.5 and the shape of the recoiling spectra influence its opacity in different WIMP masses and cross sections regions. In general, the discovery limit of an experiment improves when the exposure or the number of observed background neutrino events N increases. Until the experiment stays background free, the limit on the cross section \sigma evolves as \sigma\propto N^{-1} . With increasing N , the limit progresses into Poissonian background subtraction with sensitivity improving as \sigma\propto 1/\sqrt{N} . At some point, depending on the uncertainties in the background fluxes \delta\Phi , the limit gets stalled and becomes purely dominated by systematics as \sigma\propto 1/\sqrt{(1+N\delta\Phi^{2})/N} . More formally, let n be the improvement in the cross section limit for SI with the increase of N , defined as [ 111 ] : n=-\left(\frac{d\ln\sigma_{n,SI}}{d\ln N}\right)^{-1}. (2.29) From what discussed above n=1 when an experiment has no background, whilst n=2 when the background can be Poissonianly subtracted. The recoils induced by neutrinos do not have exactly the same energy distribution as the ones cause by WIMP interaction and in large numbers can be statistically separated. Therefore, eventually, the limit can still emerge from saturation and return to a \sigma\propto N^{-1} scaling, but only at an extremely large exposure not worth the cost-to-benefit investment. In this context, the Neutrino Floor for each experiment can be consistently defined as the largest cross section for which n crosses the value of 2. Figure 2.6 shows the value of n , defined above as the index with which a discovery limit scales with the number of background events, for xenon targets, along with some experimental limits on the SI WIMP to nucleon cross section that will be discussed in Section 2.2.2 . The colour intensity on n stresses the regions of the parameter space where the neutrino events hinder more the DM search. In spite of the fact that the discrimination between neutrinos and WIMPs induced events is possible, a n>2 stresses that, employing the same detection technique, the improvement in the discovery limit does not justify the immense investments required to increase the exposure accordingly. Among the different approaches that can be used to minimise the limitations imposed by neutrinos, directionality appears to be the most effective [ 110 , 112 , 113 ] and will be discussed in Section 2.3 . 2.2.2 Direct dark matter searches experimental techniques The experimental approaches to detect WIMP induced NRs are diverse and employ a wide range of technologies. These are based on the possibility of measuring the energy deposited in matter by a particle interaction through either ionisation, scintillation or heat. Since the energy partition into this three channels depends on the particle nature and energy (and target), the simultaneous measurement of more than one component provides discrimination between NRs and ERs. This is, in fact, related to the specific energy release mechanism of each particle type, which basically reflects the energy loss profile. In some other cases, the response of the medium changes according to the recoiling particle. For example, the noble liquid scintillating properties allow a pulse shape discrimination. Indeed, NRs and ERs excite the atoms of the liquid differently, generating distinct populations of triplet and singlet states, whose average lifetime before decaying with the emission of photons strongly differs. Solid scintillators exploit the doping of additional elements which causes the generation of extra energy levels in the lattice, from whose decay light is emitted. Akin to noble liquids, electrons in these energy states have various lifetimes of decay and ERs and NRs populate these energy states with different lifetimes in distinctive ways. For imaging detectors, the local energy deposition can be taken advantage of, with NRs having larger and strongly different distributed dE/dx along the track with respect to ERs. Finally, experiments can be built in such a way that the energy deposits of ERs do not induce a detectable response due to the low dE/dx. Following [ 36 ] , a brief summary of some of these techniques is presented supported by Figure 2.7 . The experimental approaches most relevant for directional DM searches, namely nuclear emulsions and gaseous Time Projection Chambers (TPCs), will be illustrated in detail in the dedicated directional Section in 2.3 . Figure 2.7: Schematics of the working principles of the most common detectors for direct searches: (a) scintillating crystal; (b) bolometer; (c) single-phase and (d) dual-phase liquid noble gas detectors; (e) bubble chamber. Figure taken from [ 36 ] . Scintillating crystal Inorganic crystals like NaI(Tl) or CsI(Tl) convert energy deposited in the material into UV or optical photons, which can be readout by low background photomultiplier tubes (PMTs). They are known to have large light yield and their experimental implementation is demonstrated to be simple and stable for long periods of time. The presence of intermediate/high Z makes them sensitive to high WIMP masses in the SI search. Difficulties in the growth of these crystals with high radiopurity induces large background contribution, exception made for the DAMA experiment. ANAIS-112 [ 114 ] , DAMA/LIBRA [ 115 ] are examples of scintillating crystal-based experiments (Figure 2.7 (a)). Bolometers Bolometers are cryogenic detectors operated at extremely low temperature, usually below 50 mK, whose main detection channel is based on the exploitation of their large heat capacitance to measure the increase in temperature caused by the phonons produced by a recoil inside their volume. The excellent energy resolution, the energy threshold potentially at the eV scale, and the small impact of the quenching factor on the phonon production are the highlight parts of the bolometers. In order to reject the ER background component, bolometers are typically sensitive to another energy deposition channel, namely ionisation or scintillation. Experiments based on semiconductor crystals take advantage of the collection of the charge, thanks to the very small energy gap required for ionisation, whilst scintillating crystals profit from the light emission. Since the growth of these scintillating crystals with extremely low radioactivity is problematic, the exposure attained are still limited. Examples of experiments implementing bolometers are EDELWEISS-II [ 116 ] , CRESST-III [ 117 ] , COSINUS [ 118 ] , and Super-CDMS [ 119 ] (Figure 2.7 (b)). Noble liquid detectors Noble liquids like argon and xenon can be easily ionised and possess excellent scintillation properties. The excitation of atoms by the passage of an ionising particle causes the generation of a population of excited states in triplet and singlet states whose relaxation provokes the emission of UV photons with different decay times. The type of ionising particle affects the population of triplet and singlet states. Thus, experiments can measure the primary scintillation light by instrumenting a large volume of noble elements with light detectors. Good particle identification is obtained by analysing the shape of the scintillation signal. In liquid form at low temperatures these experiments can reach large masses of the order of tonnes. Examples of these single phase noble liquid detectors are DEAP-3600 [ 120 ] or XMASS [ 121 ] (Figure 2.7 (c)). Noble elements can be used in dual phase TPCs in order to measure both the scintillation light and the ionisation charge. The primary light is collected by photo-sensors, S1 signal, whilst the charge is drifted by means of an electric field towards a grid that separates the liquid part from the gaseous one. Here, the primary ionisation electrons are strongly accelerated and thanks to electro-luminescence phenomenon their signal is amplified into photons and measured by optical sensors, S2 signal. From the combination of S1 and S2 the energy deposited, particle identification and absolute position of the interaction can be determined. XenonnT [ 122 ] , DarkSide [ 123 ] are examples of experiments based on this technology (Figure 2.7 (d)). Bubble chamber Superheated liquids can be operated in metastable thermodynamic conditions wherein they are virtually insensitive to gammas or electrons. An energy deposition in this metastable state will result in nucleating a bubble that can grow to macroscopic scales and be optically detected. The higher the degree of superheat, the lower energy threshold for bubble nucleation. In addition, superheated fluids are uniquely sensitive to the local energy deposition, or stopping power dE/dx. Since ERs have a much smaller dE/dx with respect to NRs, they result extremely inefficient at nucleating bubbles, effectively becoming incapable to induce a signal in these kind of experimental approach. This feature effectively implies a threshold both in energy and in energy density of the deposit, which allows to be completely insensitive to low energy ERs. Experiments based on this approach can not therefore measure the energy of an interaction and rely only on counting statistics for the WIMP search, being unable to characterise the DM mass in case of discovery. PICO [ 124 ] is the most successful experiment of this category (Figure 2.7 (e)). 2.2.2.1 Current limits As the unknown variables of the WIMP model determining the nuclear recoil characteristics are two, the total WIMP to nucleus cross section and the WIMP mass, a positive detection of DM induced events will allow to define a contour in the parameter space of these two variables. If instead no event is detected, only an upper bound limit contour can be determined. Figure 2.8 shows the current status of the SI limits on the cross section versus WIMP mass parameter space based on nuclear recoils searches. The DAMA/LIBRA experiment, based on NaI scintillating crystals, has observed an annual modulation of NRs in the energy range between 2-6 keV with a 2.86 tonne y exposure and 13.7 \sigma significance, which is consistent with WIMP hypothesis [ 115 ] . Translating the annual modulation observed by DAMA into constraints in the free parameter space allows to evaluate two possible signal regions with 90% confidence. Figure 2.8: Current status of the SI limits on the cross section WIMP mass parameter space based on SHM assumption and nuclear recoils searches. Figure taken from [ 36 ] . Despite the extremely large significance, more sensitive experiments have not found any hint of DM interaction even when probing smaller cross section than the constraints obtained from the DAMA data suggest. Therefore, and because of the small amplitude of the modulation, DAMA results could be affected by uncertainties which may mimic this modulation, from the possibility that the background itself could be modulated in time to systematics arising from the choice of the analysis technique itself [ 125 , 126 , 127 , 128 ] . In order to solve this tension, experiments like COSINE-100 [ 129 ] , ANAIS [ 114 ] and COSINUS [ 118 ] have being designed or are already taking data with the same target material as DAMA/LIBRA, though they have not yet matched the crystal radiopurity achieved by DAMA collaboration. Despite the exposure needed to test the annual modulation hypothesis has not been reached yet, the 90% upper bound limits obtained analysing the energy spectrum are already excluding the DAMA regions [ 129 , 114 ] . The majority of the other experiments measure only the energy spectrum of the recoils and none ever claimed any discovery. As a consequence, the 90% confidence level exclusion limits are set by the experiments based on the assumption described in Section 2.1 , in order to compare the different setups and techniques. The typical shape of a limit put by a single element target is characterised by a minimum, in the WIMP mass region close to the atomic mass of the target for kinematic reasons (see Section 2.1.4 ). For larger WIMP masses, the event rate is overall suppressed by 1/m χ . Given that the local DM density is a constant, the heavier the individual particles, the less particles are available for scattering. Conversely, at lower WIMP masses than the minimum, the energy threshold more steeply raises the limit value. Limits at large masses, above 3 GeV/c 2 , are dominated by large Z noble liquid TPCs as they reached monolithic tonne scale masses with relative ease thanks to the excellent scintillating properties and high density of these media. Figure 2.9: On the left the current status of the SD limits on the proton cross section WIMP mass parameter space based on nuclear recoils searches. Figure taken from [ 124 ] . The most relevant limits are from PICO-60 (blue), PICO-2L (purple), PICASSO (green), SIMPLE (orange), Panda-X (cyan). On the right, the current status of the SD limits on the neutron cross section WIMP mass parameter space based on nuclear recoils searches. Figure taken from [ 130 ] . Figure 2.8 shows Xenon1T with the best limits even though recently published results by LUX-Zeplin experiment further improved the state of the art with 3 \cdot 10 -47 cm 2 at 100 GeV/c 2 [ 131 ] . On the other hand, improvements in low WIMP mass can be achieved by employing light targets and small energy thresholds. In fact, the region between 1 and 10 GeV/c 2 WIMP mass still remains theoretically well motivated and largely unexplored to these days. Bolometer detectors with \mathcal{O} (10) eV energy threshold such as CREST-III and SuperCDMS published the best limits in this region, though a wide region of the parameter space is still left uncharted. The sensitivities reached in the SD coupling (Figure 2.9 ) are between 10 5 -10 7 times weaker than for the SI coupling. This is mainly due to the restricted availability of spin-odd target nuclei sensitive to axial vector currents and due to the lack of the coherent enhancement term A^{2} in the interaction. Figure 2.9 on the left shows the 90% confidence level on the WIMP to proton SD interaction and on the right on the WIMP to neutron SD interaction. PICO is the leading experiment in the SD to proton interaction thanks to the large exposure achievable in the dense overheated liquid used in the bubble chamber and to the high fluorine content, which grants high SD coupling [ 124 ] . Instead, the natural 129 Xe isotope provides quite large SD coupling with the neutron and the high density of xenon allows large exposures to be attainable [ 130 ] . In this regard, LUX possess the best limit in the SD to neutron parameter space. In this panorama, several experiments reported a significant number of observed excesses of unexpected low-energy events in the latest years. Deviations from expectation were detected in a variety of distinct experimental techniques and in both NR and ER signatures, such as Xenon1T [ 132 ] , DAMIC, SuperCDMS, CRESST-III, and EDELWEISS among the many [ 133 ] . These anomalies are being actively tackled down by the various collaborations, in some cases by demonstrating the disappearance of the excess in larger detector with reduced backgrounds [ 122 ] , and in others by joining forces and sharing the knowledge about the individual observations [ 133 ] . Thus, direct DM search has been (and is still) hampered by many false promises, since all the experimental approaches discussed so far lack the capability of a positive identification of a DM signature. In addition to this, current Xe-based and several next generation experiments will be sensitive to the Solar, atmospheric and diffuse supernovae neutrinos. All these considerations consequently advocate the development of experimental approaches able to provide a positive and unambiguous identification of a DM signal, even in presence of (unknown) backgrounds. This is the goal of directional DM searches, whose methods and reasons will be discussed in the following Section. 2.3 Directional dark matter searches The measurement of the direction of the recoils induced by WIMPs can improve substantially the search for DM, from an easier discrimination of the signal from the background to a potential mean of positive identification of WIMP. Equation 2.25 shows the double differential rate in solid angle and energy for a Earth-based detector as a function of time, while the most relevant contribution to the directional dependence is expressed in Equation 2.30 . \frac{dR}{d\cos\gamma}\propto\int_{E_{thr}}^{E_{max}}e^{-\frac{\left(v_{lab}\cos\gamma-v_{min}\right)^{2}}{v_{p}^{2}}}, (2.30) The term v_{lab}\cos\gamma is fundamental as, on one side, predicts that WIMPs coming from a certain direction will have larger velocities and thus be more easily detected, and, at the same time, it induces a strong directional anisotropy, clear when the recoil spectrum is expressed in Galactic coordinates. In these coordinate system any non-WIMP induced recoil distribution is expected to be flat. Therefore, the anisotropic feature of the recoil spectrum cannot be mimicked by any form of background [ 83 ] , which makes this feature to be considered a smoking gun of the WIMP DM scenario. Figure 2.3 shows two examples of angular distribution in Galactic coordinates of WIMP induced recoils on fluorine and xenon targets with different WIMP masses, obtained by integrating Equation 2.25 on the available energy range (for operative details see Section 7.2 ). The anisotropic behaviour can manifest itself in various realisations. The value of \gamma for the recoil depends, in fact, on the combination of the recoil energy E , the WIMP mass, the target mass and the laboratory velocity according to: \cos\gamma=\frac{v_{min}}{v_{lab}}=\sqrt{\frac{m_{A}E}{2\mu_{A}v_{lab}^{2}}}. (2.31) Thus, the maximum \gamma can vary from 0 up to 90 degrees. When \gamma peaks at 0, or at very small values, the angular distribution displays a dipole in Galactic coordinates, as can be seen in Figure 2.3 on the left. In this configuration, the preferred recoil direction is in the opposite direction of Earth’s motion with respect to the Galactic Rest Frame, which approximately corresponds to the Cygnus constellation location. The ratio of recoil rates in the forward over the backward directions can reach differences by a factor of order 100, evaluated on the left panel of Figure 2.3 . The spread of the dipolar distribution depends on the energy range of the recoils, with larger energies leading to more peaked structures. The actual distribution of the measured direction of nuclear recoils eventually depends on the experimental performances, such as angular resolution and energy threshold. Conversely, when v_{min}>s_{ep} , with the latter being the distance between the hyperfocal plane and the entrance plane. In the context of the CYGNO experiment, this is true, thus, it is valid that: \frac{1}{f}=\frac{1}{s}+\frac{1}{s^{\prime}}. (3.3) I=\frac{y^{\prime}}{y}=\frac{s^{\prime}}{s}, (3.4) with y and y^{\prime} the object and image dimension respectively. Combining Equation 3.2 with 3.3 and 3.4 it is possible to derive: \Omega_{f}=\frac{1}{\left(4N\left(\frac{1}{I}+1\right)\right)^{2}}, (3.5) with N the f-number or aperture ratio, defined as N=D/f . The typical solid angle covered with the Schneider lens and, for example, the ORCA Fusion camera (second row of Table 3.1 ) when imaging an area of 30 \times 30 cm 2 is of \mathcal{O} (10 -4 ), significantly reducing the number of photons that reach the active sCMOS sensor. As a result, an extremely high gain is required from the amplification stage, which leads to the employment of the stack of three GEMs (see Section 3.1.2 ). 3.2 CYGNO timeline The CYGNO project aims to deploy a large scale detector for directional search of DM and Solar neutrino spectroscopy. In order to characterise and optimise the experimental technique, numerous prototypes were developed. Figure 3.10 shows the roadmap of the experiment, while Table 3.2 shows some of the main features of the prototypes. The first prototype, ORANGE, had a 10 \times 10 cm 2 area with a 1 cm drift gap and was used to demonstrate the possibility of detecting \mathcal{O} (1) keV energy deposits in the gas coupling a sCMOS camera to a GEM amplification stage, and to assess the feasibility of the 3D reconstruction with the addition of a PMT [ 194 ] . ORANGE was followed by LEMOn, which possesses a 20 cm drift gap and a larger readout area (20 \times 24 cm 2 ). LEMOn was utilised to deepen the knowledge on the performances of the detector as a function of a larger drift distance and area. A prototype with a 10 \times 10 cm 2 readout area and variable drift region, MANGO (not present in Figure 3.10 ), was also manufactured in 2018 to perform R&D tests on the gas properties and amplification structures. In 2019, the LIME prototype was completed, a 50 cm drift with 33 \times 33 cm 2 readout area detector, which represents the fundamental building block of the larger scale experiment. After overground commissioning, LIME was installed in underground Laboratori Nazionali del Gran Sasso (LNGS) in June 2022, in order to characterise the detector in a realistic environment. All the mentioned prototypes constitute the CYGNO PHASE_0, whose goal is to validate the full performances of the optical readout via APS commercial cameras and PMTs and the Monte Carlo simulation of the expected backgrounds. PHASE_0 is to be followed by PHASE_1, CYGNO-04, a 0.4 m 3 detector to be installed at the LNGS which will be realised with all the technological and material choices foreseen for the future CYGNO-30. This phase aims at demonstrating the scalability of the experimental approach and the potentialities of the large PHASE_2 detector to reach the expected physics goals. Figure 3.10: Schematic of the roadmap of the CYGNO experiment. Finally, CYGNO-30, a \mathcal{O} (30) m 3 detector, represents the PHASE_2 of the project. A CYGNO-30 experiment would be able to give a significant contribution to the search and study of DM with masses below 10 GeV/c 2 for both SI and SD coupling, with the addition of exploiting all the advantages of a directional DM search (see Section 2.3 ). The following Sections will describe the various prototypes and the main results achieved with each of them. Prototype Readout area (cm 2 ) Drift length (cm) Readout Purpose ORANGE 10 \times 10 1 1 sCMOS + 1 PMT Proof of technique LEMOn 20 \times 24 20 1 sCMOS + 1 PMT Stability and background studies MANGO 10 \times 10 1-15 1 sCMOS + 1 PMT R&D for Phase_2 LIME 33 \times 33 50 1 sCMOS + 4 PMT Underground operation, MC validation CYGNO-04 50 \times 80 2 \times 50 4 sCMOS + 12 PMT Scalability test, radiopurity CYGNO-30 N.A. N.A. N.A. Physics case Table 3.2: Short summary of the main features of the various prototypes of the CYGNO project. 3.3 The MANGO detector The Multipurpose Apparatus for Negative ions studies with GEM Optically readout (MANGO) is a small detector with a 10 \times 10 cm 2 amplification area and a variable drift region. This detector is employed in the studies presented in Chapter 5 and 6 . A sketch of the MANGO prototype and the internal TPC structure is shown in Figure 3.11 and described in details [ 211 ] . The amplification stage consists in a stack of multiple 10 \times 10 cm 2 GEMs spaced 2 mm, with a transfer field of 2.5 kV/cm in between the GEMs. MANGO is typically operated with triple 50 \mu m thin GEM, but different thicknesses and stacking option were tested as it will be shown in Chapter 5 . The GEMs are numbered from 1 to 3 with GEM1 being the closest to the drift region. The GEMs are powered by the HVGEM [ 212 ] , a dedicated high voltage supply developed by the Laboratori Nazionali di Frascati (LNF), which works as an active high voltage (HV) divider. The HVGEM is employed to power seven floating independent channels (that is the upper and bottom electrodes of the 3 GEMs plus one potential extra electrode), with each channel isolated up to 5 kV to ground and with a high sensitivity ( \sim 1nA) current meter. Figure 3.11: A simple representation of the MANGO setup with exemplified a triple GEM amplification. The TPC, typically operated in continuous gas flux mode, is enclosed in a 3D printed black plastic light-tight box that contains a gas-tight acrylic internal vessel. A thin window of highly transparent (> 0.9) Mylar® decouples the gas detector from the optical readout, which consists in a PMT (Hamamatsu H3164-10 5 5 5 https://www.hamamatsu.com/eu/en/product/optical-sensors/pmt/pmt-assembly/head-on-type/H3164-10.html ) and a C14440-20UP ORCA-Fusion sCMOS camera (second row of Table 3.1 and C in Figure 3.11 ), placed at a distance of (20.5\pm 0.3) cm and focused on the last GEM amplification plane. The camera possesses a squared silicon sensor of 1.498 \times 1.498 cm 2 are, segmented in 2304 \times 2304 pixels. Each pixel has a QE of about 80% at 600 nm, and a readout noise of 0.7 electrons RMS. The optical sensor is equipped with a Schneider Xenon lens (Appendix D and B in Figure 3.11 left). Within this scheme, the camera images an area of \sim 11.3 \times 11.3 cm 2 , resulting in an effective pixel size of \sim 49 \times 49 \mu m 2 . 3.4 The LEMOn detector A sketch of the Long Elliptical MOdule (LEMOn) detector is shown in Figure 3.12 . A 7 litres active volume TPC with a 20 cm drift length and a 24 \times 20 cm 2 readout area is enclosed in a gas-tight acrylic vessel and operated in continuous gas flux mode. An ellipsoidal field cage comprised of silver wires held by 3D printed plastic supports with 1 cm pitch guarantees drift field uniformity in the 20 cm drift gap. The cathode is made by an ATLAS MicroMegas mesh [ 213 ] with 30 \mu m diameter metallic wires with a pitch of 70 \mu m. Three 24 \times 20 cm 2 , 50 \mu m thick GEMs spaced each other 2 mm comprise the amplification stage. The GEMs are numbered from 1 to 3 with GEM1 being the closest to the drift region. LEMOn cathode and field cage base are powered by a CAEN N1570 6 6 6 https://www.caen.it/products/n1570/ HV supply, while the GEMs by a CAEN A1526 7 7 7 https://www.caen.it/products/a1526/ power supply with 6 independent HV channels up to 15 kV and a current sensitivity of 10 nA. This powering configuration provides a very precise tool of measurement of the charge on each of the GEM electrodes. Figure 3.12: The LEMOn prototype [ 171 ] . The elliptical sensitive volume ( A ), the fast photomultiplier ( B ), the optical bellow ( C ) and the sCMOS-based camera ( D ) are indicated. The LEMOn detector is optically coupled to a Hamamatsu sCMOS camera ORCA FLASH 4.0 (first row of Table 3.1 ) through a TEDLAR transparent window and an adjustable plastic bellow. The camera has a calibrated response of 0.9 counts/photons [ 214 ] . The sensor is equipped with a Schneider Xenon lens (see Appendix D ). The ORCA-Flash is positioned at (50.6\pm 0.1) cm distance from GEM3 and reads out an area of 25.6 \times 25.6 cm 2 . Therefore, each of the 2048 \times 2048 pixels of the sCMOS sensor images an effective area of 125 \times 125 \mu m 2 . On the opposite side, behind the transparent cathode, a HZC Photonics XP3392 PMT is positioned. The drift field is set to 0.5 kV/cm and the transfer fields between GEMs at 2.5 kV/cm, while the voltage across the GEMs of 460 V was utilised in order to provide a gain of 1.5 10 6 [ 194 ] . The LEMOn prototype was utilised to validate the concept of the detector on a medium scale and to measure the energy resolution, the stability performances, to provide a preliminary estimation of the absolute position along the drift direction and the first assessment of the background rejection. With the LEMOn detector it was possible to demonstrate on a medium size TPC that the detection efficiency of a 5.9 keV electron recoil is 100% with drift fields above 300 V/cm independently of the drift distance. A more detailed description of LEMOn and its performances can be found in [ 171 , 215 , 216 ] . The LEMOn prototype is also utilised for the studies described in Chapter 5 . 3.4.1 Background rejection Figure 3.13: Detection efficiency for nuclear recoils ( \epsilon^{total}_{s} ) as a function of their detected energy for an efficiency on 55 Fe electron recoils of 4% (squares) and 1% (circles). The capability to discriminate between ERs and NRs is of paramount importance for rare event searches, see Section 2.2.1 . The high granularity of the optical readout allows to retrieve a large amount of information on the track shape, that can be efficiently exploited to identify its ER or NR origin. In order to evaluate background rejection capability of the CYGNO experimental approach, LEMOn was exposed to a 55 Fe source producing ERs at 5.9 keV and an AmBe source producing NRs (properly shielded with lead blocks to suppress the gamma flux emitted by the source). The gas mixture used is a He:CF 4 (60/40) at atmospheric pressure and room temperature with a flux of 200 cc/min. A reconstruction algorithm based on DBSCAN and discussed in detail in Chapter 4 is employed to find and reconstruct tracks in the sCMOS images. It is based on the Density-Based Spatial Clustering of Applications with Noise (DBSCAN) [ 217 ] which selects clusters of pixels which are believed to belong to the same group. These are furthermore grouped according to their vicinity and their derivative in the light profile, employing an algorithm based on Geodesic Active Contour (GAC [ 218 , 219 ] ). More details can be found in Section 4.1 . The test was performed at overground facility of the Laboratori Nazionali di Frascati (LNF), implying a large contamination of cosmic rays in the data. Track shape variables were used to identify the different particles interacting in the detector. Track length and track slimness (ratio of track width over length) allow to separate the long cosmic ray tracks from the low energy ERs and NRs. Indeed, the former can cross the whole detector with reduced loss of energy per unit length producing long slim tracks, while the larger energy deposition of \mathcal{O} (1) keV ERs and NRs generate short thicker denser tracks. The pixel density \delta , defined as the ratio of the total number of photons of a track over its number of pixels, is proportional to the dE/dx stopping power of an ionising particle. Thus, this quantity can be employed to discriminate NRs, characterised by continuous and dense energy depositions, from ERs, that conversely release energy in a sparse and discontinuous pattern. Figure 3.13 shows the NR signal efficiency \epsilon^{total}_{S} as a function of the measured energy for 5.9 keV ER efficiency of 4% and 1%. An efficiency of 18% to detect nuclear recoils with an energy of about 6 keV is reached, while suppressing 96% of the 55 Fe photoelectrons, showing how this optically readout gaseous TPC is a very promising candidate for future investigations of ultra-rare events as directional direct DM searches. Even though the selection cut is very simple and minimal, a rejection power of the order 10 2 is achievable below 10 keV. More sophisticated and articulated analyses which combine multiple topological features and with the use of Machine learning techniques are under study in the collaboration, and already showed the capability to improve of about one order of magnitude on these results. 3.5 LIME The Long Imaging ModulE (LIME) is the largest prototype built so far with the CYGNO experimental approach and it is expected to conclude the R&D phase of the CYGNO project. A picture and a sketch of LIME are shown in Figure 3.14 . The TPC has a parallelepiped sensitive volume with a readout area of 33 \times 33 cm 2 and a drift length of 50 cm, for a total of 50 l active volume. These dimensions are chosen in order to reproduce the drift length of the 0.4 m 3 CYGNO-04 detector, see Section 3.6 . The vessel is made of acrylic and an external aluminium Faraday cage shields the detector from any electromagnetic interference. The top side of the vessel has a narrow opening along the drift distance closed by a thin ETFE window in order to be able to calibrate the detector with external radioactive sources. The cathode and the squared field rings of the field cage are made of copper. The rings are positioned with a pitch of 16 mm and connected via ceramic resistor to generate the partition of the voltage which produces the drift field. The amplification stage is based on a triple stack of 50 \mu m thin GEMs of 33 \times 33 cm 2 of area, each stretched on an acrylic frame rather than on conventional PCB boards to minimise the radioactivity contribution from this item. The amplification area is readout optically by a single sCMOS camera and 4 PMTs positioned towards the 4 corners in order to improve the PMT track reconstruction. Figure 3.14: On the left a sketch of the LIME detector. The structure of the acrylic vessel, the copper rings and the optical readout are shown. On the right, a picture of the field cage after the installation. The PMTs are Hamamatsu R7378A 8 8 8 https://www.hamamatsu.com/content/dam/hamamatsu-photonics/sites/documents/99_SALES_LIBRARY/etd/R7378A_TPMH1288E.pdf with 22 mm diameter bialkali photocathode sensitive from 160 up to 650 nm. The sCMOS camera is the Hamamatsu ORCA Fusion (second row of Table 3.1 ) and it is equipped with a Schneider Xenon lens (see Appendix D ). The ORCA-Fusion is positioned at \sim 62 cm distance from the farthest GEM from the sensitive volume and reads out an area of 35.7 \times 35.7 cm 2 . Therefore, each of the 2304 \times 2304 pixels of the sCMOS sensor images an effective area of 155 \times 155 \mu m 2 . After the overground commissioning, LIME was installed in the underground facility of the Laboratori Nazionali del Gran Sasso (LNGS), where it is now operating in a low background environment. The goal of LIME is to validate the full performances of the CYGNO approach in an underground environment, to verify the Monte Carlo (MC) simulation of the expected background and to test construction and operation procedures toward the realisation of PHASE_1 (see Section 3.6.1 ). In parallel, it will provide a precise, spectral and directional measurement of the environmental LNGS neutron flux (see Section 3.5.2.4 ). 3.5.1 Overground tests LIME was commissioned at the overground LNF in order to characterise its performances before the underground installation at the LNGS. The obtained results on operation stability, light yield, energy response and determination of the absolute position along the drift direction are illustrated in the following. 3.5.1.1 Stability The long term stability of LIME was tested for a month long run, during which the detector was exposed to environmental radioactivity, cosmic rays and a 55 Fe source. During the whole period, the current drawn by each of the high voltage supplier channels powering the GEMs electrodes was monitored and recorded to identify sudden and large increases that could indicate discharges or other electrostatic issues. The main instabilities observed were: • hot-spots appearing on the GEM surface. These are likely related to localised self-sustaining micro-discharges happening in one or few GEM holes. In some cases they fade away with time, in some others they start to slowly grow up to tens of nA (on a time scale of minutes). • sudden discharges. High charge density due to very high ionising particles or charge accumulation on electrode imperfections can suddenly discharge across GEM holes. These events are recognisable thanks to a sudden increase in the current drawn on the supplier channels. A voltage supply can quickly restore the drop occurred during the discharge through 10 M \Omega protection resistors on a few seconds time basis. Despite these events being less frequent than hot-spots, they can be dangerous for the GEM structure and the energy released in the discharge could damage it irreversibly. In order to protect the detector, an automatic recovery procedure was established. Whenever the drawn currents are measured beyond a customisable threshold, this procedure decreases the voltage across all the GEMs by 100 V. Then, the voltage is restored in 5 steps of 20 V with a 30 seconds of pause between each step. This procedure lasts about 3 minutes and it demonstrated the capability of recovering both hot-spots and discharges within a couple of minutes. An average of 16 instabilities per day was observed and the automatic recovery procedure introduced less than 4 \% of dead time. A detailed analysis of the time interval between two consecutive phenomena did not shown any correlation between two subsequent events, nor any increase of their rates. This study demonstrated that the detector operation is very safe and stable in satisfactory way for the purposes of the data taking. 3.5.1.2 Linearity and light yield Material Emission (keV) Calcium 3.69 Titanium 4.51 Iron 5.9 Copper 8.04 Rubidium 13.37 Molybdenum 17.44 Silver 22.10 Barium 32.06 Table 3.3: Summary of the materials and K α emissions utilised for the X-ray calibration of LIME. In order to test the response of the detector to diverse energy deposits, the emission of K α and K β lines from different materials is exploited. A target holder was positioned on the top of the EFTE window with a 45 degrees inclination with respect to it. By irradiating different materials positioned in the holder by means of a radioactive source ( 55 Fe or 241 Am), X-ray emission of K lines can be induced, with an energy dependent on the target material. The inclination of the holder is chosen in order to maximise the probability that the emitted X-rays reach LIME sensitive volume and convert in ERs into it. The 55 Fe source was also used to directly irradiate the detector in order to provide its characteristic 5.9 keV X-ray emission. The materials utilised with their K α line energy are reported in Table 3.3 . The X-rays energy ranged from 3.7 keV of calcium up to 32 keV of barium for a total of 8 lines. Images from the sCMOS camera were acquired in free running mode (i.e. without an external trigger). For each target element, additional images were acquired with the detector turned off to characterise the sensor noise that can vary along hours of data taking. The data were analysed with the reconstruction code illustrated in Section 4.1 . The energy spectrum of each dataset is fitted with a Gaussian, which represents the X-ray signal distribution, on top of a polynomial function modelling the background (typically composed by mis-reconstructed cosmic ray tracks and other low energy ERs). The mean of the Gaussian fit represents the average number of counts summed on all the pixels of the track, proportional to the number of photons and hence to the track energy. The fitted sigma defines the energy resolution. Figure 3.15 on the left, shows an example of an energy spectrum obtained during the data taking of the K lines of copper. Figure 3.15 on the right shows the preliminary results on the energy measured for each X-ray emitter as a function of the nominal original energy. The superimposed linear fit shows a good linear response up to the barium emission with negligible offset. The energy resolution was found to be roughly 14% in this range of energies, an excellent resolution for a gas detector for such low energy deposits. Figure 3.15: Preliminary results on the linearity study of the LIME detector performed at the LNF. On the left, an example of the light spectrum of the clusters found during the data taking with the 8 keV emission from a copper target material. The data are modelled as a polynomial background with a Gaussian peak on top. On the right, the measurement of the average amount of photons per X-ray emission as a function of the nominal energy. The linear fit superimposed demonstrate the linear response of the detector. Credit for this work to the fellow PhD student Samuele Torelli and Atul Prajapati. The measurement of the average number of photons collected per track allows to estimate the light yield properties of the detector. The light yield was found to be 650 photons per keV of energy deposited in the sensitive volume, estimated from the 55 Fe data. The knowledge of the light yield combined with the intrinsic noise of the camera leads to the determination of an effective energy threshold of 1 keV. Indeed, the sensor electronic noise represents a possible unavoidable instrumental background and it can generate ghost-clusters in the reconstruction algorithm. The distribution of the light in each ghost-cluster found is studied in blind data sets, when a cap was placed in front of the camera to prevent light from reaching the sensor [ 215 ] . The exponential tail of this distribution is extrapolated in order to obtain the probability of having a ghost-clusters with an amount of light larger than a given threshold. It was found that the number of ghost-clusters with more than 400 photons are expected to be \sim 3 10 -7 per second. With such a low rate, when the reconstruction code returns a cluster with 400 photons it is highly probable it is related to a real track. While this method does not define the energy threshold, 1 keV is believed to be a conservative estimation of it. 3.5.1.3 Absolute position along the drift direction The determination of the absolute position along the drift direction (z) is of the outermost importance because, once combined with the 2D projection provided by the sCMOS camera, it allows to localise an event in all the three dimensions. This is fundamental for the fiducialisation of the detector, as discussed in Section 2.2 . Figure 3.16: The dependence of the average \eta as a function of the position of the 55 Fe source away from the GEM. Credit for this work to the fellow PhD student Rita Joana Cruz Roque. The z position determination was studied positioning the 55 Fe source at various drift distances along the z axis of the detector. The z coordinate can be evaluated by exploiting the information on the diffusion a track is subject to [ 198 , 170 ] . A 5.9 keV X-ray is absorbed by the gas producing an electron via photoelectric effect. Typical ER track length dimension at these energies is of the order of 100 \mu m. Given the diffusion coefficient of the CYGNO gas of about 100 \mu m/ \sqrt{cm} (see Figure 3.2 ), diffusion during drift will dominate over the original distribution of primary electrons. Thus, the signature of an 55 Fe signal on a sCMOS image is a round spot. The spatial distribution of the pixels can be approximated to a Gaussian with standard deviation \sigma and amplitude A_{G} . Depending on the z-coordinate of the recoil, the transverse diffusion increases enlarging \sigma , whilst decreasing A_{G} . The ratio \eta defined as \sigma / A_{G} is expected to grow with the drift distance. Figure 3.16 shows the average \eta , evaluated on all the tracks reconstructed per z position of the 55 Fe source, as a function of the nominal depth of the track, with superimposed a linear fit. The plot demostrates that \eta is sensitive to the average depth of the tracks. Yet, the \eta distribution of each data set results rather large due to experimental effects, especially the not optimal collimation of the source, complicating the actual event-by-event determination of the depth in the data acquired so far. MC simulations of the non collimated geometry of the source in the LIME setup suggest a resulting spread in z of the 55 Fe signal of \sim 5.5 cm. Employing a random forest regression algorithm [ 220 ] on multiple shape variables, among which \eta itself, an estimation of the z coordinate is obtained with a dispersion of \sim 6 cm, very close to the simulated one. Future data acquisition with a collimated 55 Fe source will provide a better estimation of the resolution in the reconstruction of the absolute z coordinate, improving the preliminary 15% obtained with the LEMOn detector by measuring 450 MeV electron tracks at the LNF BTF line [ 198 ] . 3.5.2 Underground installation One of the main goals of the LIME prototype is to assess its performances in the low background underground environment of LNGS, where it has been operating since June 2022. The experimental area is located in a container in the corridor between Hall B and Hall A, in front of DAMA/LIBRA experiment. The container spans across two floors where the bottom one contains the detector (and the future shielding) and the top the control room, which hosts also the DAQ servers and modules, and the high voltage suppliers. Figure 3.17 shows two pictures of the underground LIME site. The gas system is located just outside the experimental area and is an Air Liquid GAS system which provides the flow of the mixture to the detector, purification from impurities, as well as its recirculation and its recovery for the disposal of greenhouse gases. Figure 3.17: Pictures of the ground floor (left) and the first floor (right) with respectively LIME detector inside its Faraday cage and the control room. In the following Sections, the slow control and DAQ system LIME is equipped with will be described, as well as the background simulations and the future plan of measurement. 3.5.2.1 Slow control During operation, LIME is handled by an open source C++ based slow control software developed within the MIDAS framework 9 9 9 https://daq00.triumf.ca/MidasWiki/index.php/Main_Page . MIDAS is a versatile software capable of interfacing with a wide range of sensors and electronic boards. The goal of the slow control is to setup the detector operating condition and periodically monitor its performances and functioning. In the CYGNO setup, this MIDAS-based software controls the high voltage suppliers of PMTs, cathode and GEMs, and records the currents drawn by the latter in order to activate recovery procedures in case of instabilities (see Section 3.5.1.1 ). Furthermore, the slow control is connected to temperature and pressure sensors positioned inside the detector and in the room at the ground floor, in order to continuously monitor LIME working conditions and possible gas leakages. In parallel, it handles error messages and alarms delivered by the gas system in case of malfunctioning. Finally, it performs a first raw analysis of the PMT waveforms and of the sCMOS images to monitor the data quality during data taking. Figure 3.18 shows on the left, an example of two variables used to check the regularity of operation of the sCMOS camera. The average number of clusters found in a set of images and total amount of photons collected are indicators of the correct gas purity and electronic stability of GEMs and camera. Figure 3.18 exhibits, on the right, an example of a picture taken with the sCMOS camera in the underground laboratories at LNGS highlighting the reduction of the cosmic rays component in the underground environment. 3.5.2.2 DAQ system Figure 3.18: On the left an example of two variables of the slow control which check the quality of the data captured with the sCMOS camera. Occurrences of issues was notice by the slow control during this initial test phase. On the right, an example of an image from the sCMOS camera taken on LIME at the underground laboratories of LNGS. The Data Acquisition system (DAQ) is a set of hardware and software components responsible for the handling, acquisition and storage of the data. In the context of the CYGNO experiment, the challenging task of DAQ is to collect synchronized data from sCMOS cameras and the PMTs (i.e. detectors that have a difference in the response time of orders of magnitude), while handling the logic of the trigger. In the context of the LIME detector, the current signal waveforms induced on the bottom of GEM2 and GEM3 are also acquired by the DAQ, in order to better characterise the prototype performances and features. The sCMOS camera is interfaced to the DAQ computer via USB 3.0 cable, which allows to transport the images, each of \sim 5 MB, at the maximum rate allowed by the ORCA-Fusion, 5.5 Hz. The typical time length of a PMT signal of short nuclear and electron recoils in a TPC filled with He:CF 4 depends on the inclination of the track with respect to the drift direction. On average, it ranges from few tens up to few hundreds of ns. Moreover, the usual risetime of this photosensor electrical circuit of the order of ns permits, in principle, to detail its waveform down to the ns scale. To cope with these requirements, a CAEN VME digitizer V1742 10 10 10 https://www.caen.it/products/v1742/ was selected to sample the PMT waveforms. It possesses 32 channels, each one with 1024 switched capacitor sampling cells at 12 bits and a sampling frequency which can vary from 750 MS/s up to 5 GS/s. In the configuration with 1 GS/s, it allows to sample every PMT signal with 1 ns step for an entire \mu s, enough to contain the desired waveform with a high precision both in sampling and voltage sensitivity. On the other hand, the signal induced on the GEMs is influenced by the motion of the ions produced during the amplification which causes their time extension to be much longer. As a consequence, the CAEN VME V1761 11 11 11 https://www.caen.it/products/v1761/ digitizer was selected for these, with two 10 bit channels equipped with a 4 GS/s Flash ADC and 7.2 MS of memory buffer. This way, a detailed sampling of the GEM waveform can be performed for a maximum time of 1.8 ms in order to include the entirety of the signal. To handle the VME digitizers and their connection to the DAQ server, a CAEN VME bridge V1718 12 12 12 https://www.caen.it/products/v1718/ is employed. In addition, to correctly communicate the commands received by the DAQ computer to the digitizers, these bridges also possess programmable outputs which can act as vetoes. The challenge of a data acquisition with these different optical detectors lies in their imbalanced typical time of operation. Indeed, as the typical extent of a PMT waveform is of a \mu s, the sCMOS camera takes 80 \mu s just to expose one of the 2304 rows of the silicon matrix. The usual exposure time selected for the data taking is of 300 or 500 ms, 10 5 times longer than the PMT signals. In order to obtain a synchronised data acquisition of all the sensors, a custom front end program was developed and integrated in the MIDAS software. The acquisition is divided into runs, each composed of a variable number of events. An event is defined as a collection of a sCMOS image together with all the PMT and GEM waveforms generated during the camera acquisition window. The sCMOS is kept in continuous acquisition mode so that images are taken repeatedly without any pause. The sensor is opened to expose the pixels, kept open for the exposure time length, closed and finally the trigger signal is checked to decide whether to store the image or to discard it. The trigger signal is the logic AND of two variables: lamPMT , coming from a logic analysis of the PMT signals, and lamCAM coming from the camera. lamPMT is positive if two or more PMT waveforms have at least one sample below a predetermined voltage threshold (PMTs have negative polarity signals). This was fixed at - 5 mV, in order to provide 100% efficiency on the signal while minimising noise events from single photoelectron background. The logic signal lamCAM is positive when all the pixels of the camera are exposed together. This way, the trigger is positive when more than a PMT received a sufficient number of photons from the amplification stage while the whole sensor was exposed, in order to be certain to have the signal detected by all the sensors. A single positive trigger is enough to force the storage of the sCMOS picture. More triggers can occur during a single image, and every time the trigger signal is positive, the digitizers sample the waveforms for a maximum of 128 in total. When the sCMOS picture is saved to disk also the buffer of the digitizers is transferred to the DAQ server and compressed along with the picture in a single event. This choice of data acquisition logic could in principle hinder the correspondence between each PMT waveform and the relative track in the CMOS image in case of high occupancy, limiting the 3D reconstruction capabilities. Nonetheless, the typical LIME rate of events in an underground environment (of few Hz in absence of shielding, see Section 3.5.2.3 ), combined with the possibility of inferring the track x-y position from the PMT waveforms light barycentre, will grant the match of the two signals. During several campaigns at LNF, the DAQ system was tested and adapted to recognise different digitizers and various logic structures to maximise its flexibility. It will be thoroughly tested during the underground operation, as it represent the basic structure of the DAQ for the future CYGNO detectors. During the last months, LIME was commissioned in the underground facility, testing the performances of DAQ, slow control and gas system utilising a 55 Fe source. The stability of the LIME setup allowed the data taking to be undertaken from remote control. 3.5.2.3 LIME background studies Figure 3.19: Result of the GEANT4 simulation of the internal radioactivity of LIME. On the left the sum of the ER and NR induced by radioactive background interactions. On the right only the NR are shown. The different detector components causing the recoils are separated by means of the colour scheme displayed in the legend. Credit for this work to the fellow PhD student Flaminia Di Giambattista. The characterisation and knowledge of the radioactive background is of the utmost importance for rare events searches (see Section 2.2 ). For this reason, a thorough MC simulation of the expected background in LIME was performed with the GEANT4 package [ 195 ] . The CAD engineering design of the prototype was implemented in the simulation, as well as the different shielding configurations. The radioactive background coming from outside the detector ( external background ) is simulated from the spectra of neutrons and \gamma s fluxes measured at the LNGS by other experiments (see Figure 2.4 and [ 221 , 101 ] ). The intrinsic radioactivity of the main components used to manufacture LIME (cathode, copper, field rings, resistors, GEM, vessel acrylic, camera lens and body) were measured thanks to the LNGS Services with high purity Ge detectors, and used in the simulation of the internal radioactivity . Relevant contributions from 238 U, 235 U, 232 Th chains and 40 K were found. In particular, large contamination of 234 Th were measured in the resistors, cathode, field rings, camera body, lens and GEMs up to 20 Bq/kg. Resistors also contains large amount of 234m Pa, 226 Ra, as for the GEMs and cathode and field rings, and 210 Pb. Copper activation isotopes as 58 Co was found in small amount in the field rings and cathode. Relevant contribution also derives from the 40 K contamination of camera sensor and lens, along with GEMs and resistors. It has to be stressed that LIME was built with standard materials, not optimised in terms of low intrinsic radioactivity. In the unshielded configuration, where only the Faraday cage is present, the external background dominates inducing a total \sim 10 9 events per year above 1 keV, a rate of \sim 36 Hz. A cost-benefit study was performed in order to optimise the shielding configuration with the goal of maximising the suppression the external contribution while minimising the costs, taking into account the available space and additional radioactive contribution introduced by the shielding materials. The most cost-effective solution found was to employ a copper shield, 10 cm thick, encased in a water tank shield of 40 cm thick. The copper component is used to stop all the \beta emissions and significantly reduces the gamma \gamma ones. On the other hand, the water is utilised to slow down and capture neutrons, thanks the large quantity of hydrogen present in the liquid. This shielding configuration is expected to grant that less than 2 NRs per year above 1 keV are induced by external background in the active detector volume, while the ERs are reduced to 10 5 per year between 1 and 20 keV. These values are deemed small enough for LIME purposes (see Section 3.5.2.4 ), since the simulation of the internal radioactivity returns a total number of recoils induced in the sensitive volume of about \sim 7 10 6 events per year, making it the dominant component in the full shielding configuration. Figure 3.19 shows the energy spectrum of the total number of recoils induced by internal radioactivity on the left, while the right plot displays only the NRs. The various colours exhibit the contributions from each of the main detector component included in the simulation. The field rings, resistors and GEMs are among the highest contributors to the radioactivity budget, with considerable impact also from the camera lens and body. Shield External Internal Total ER/yr NR/yr ER/yr NR/yr ER/yr NR/yr No shield 1.13 10 9 1450 7.26 10 6 6.11 10 4 1.14 10 9 6.25 10 4 4cm Cu 2.64 10 7 850 7.26 10 6 6.11 10 4 3.43 10 7 6.19 10 4 10cm Cu 1.95 10 6 915 7.26 10 6 6.11 10 4 9.78 10 6 6.20 10 4 10cm Cu + cuts N.A. 772 N.A. 16 N.A. 788 40cm H 2 O +10 Cu 5.09 10 5 2.0 7.26 10 6 6.11 10 4 8.34 10 6 6.11 10 4 40cm H 2 O +10 Cu + cuts 2.0 10 4 2.0 2.8 10 5 17 3.3 10 5 19 Table 3.4: Summary the simulated background from internal and external contributions in the LIME detector with different shielding configurations. The recoils are considered above 1 keV of energy. The total column also contains the additional contribution coming from the shielding material radioactivity, which is not explicitly reported in the rest of the table. This is of great importance in order to tackle down the radiopurity issues for the future detectors. The MC simulation shows that it is possible to further reduce the external and internal backgrounds with fiducialisation. Applying geometrical cuts to the detector volume, namely 1 cm from the borders and GEMs (i.e. in x-y) and 4 cm from the cathode (i.e. in z), the background induced recoils can be reduced of 96% for ERs and 99.97% for NRs. With these preliminary cuts, below 20 keV, the total amount of recoils drops to \sim 2.7 10 5 events per year, of which only 6 are NRs. This analysis is performed on the real events simulated without the introduction of the detector performances. The collaboration is working to include the response of the detector and to optimise the cuts and the analysis strategy. Table 3.4 summarises the internal and external contributions of ERs and NRs per year in the various shielding configurations, including the fiducial cuts. The first images taken with LIME in the underground site with only the Faraday cage suggest a rate of recoils of \sim 35 Hz, in excellent agreement with the expected value from the simulation. 3.5.2.4 LIME underground program LIME underground installation and operation has multiple purposes, from the study of the background to the validation of the MC simulations, and to the measurement of the neutron flux (see beginning of Section 3.5 ). Since each goal requires different setups and level of backgrounds, the underground LIME program will proceed through a staged approach, progressively adding shielding layers around the detector. The foreseen phases are: • No shield LIME was operated with only the Faraday cage in the last months, with the goal of characterising the detector response underground and study the external radioactive background, which enormously dominates over the internal one when no shield is present (see first row of Table 3.4 ). After an initial commissioning dedicated to the test of the slow control and DAQ system and prototype calibration with 55 Fe source, about one month of background data was collected (with \sim 10 8 events per month expected) to cross check the MC simulation with real data and directly measure the backgrounds. Data analysis of the acquired events is ongoing. • 4 cm Cu . This copper shield has been recently installed in order to verify that the measured background decreases as expected from the simulations. In addition, a neutron calibration with 241 AmBe is going to be performed with this configuration, to minimise the gamma background from the source. A month is anticipated to complete this step. • 10 cm Cu . The final copper shielding configuration will be of 10 cm, a thickness able to suppress of a factor 10 3 the external gamma flux. As the neutron flux in the underground laboratories is a source of relevant background for all of the experiments and its measurements at LNGS are limited and with broad uncertainties [ 222 , 223 , 221 ] , LIME will be employed to perform a precise, spectral and directional measurement of this, which will be of paramount importance for any present or future detector at LNGS. In addition, a directional measurement of NRs in this underground environment represents an effective demonstration of the capability of the detector to search for DM via NRs. Thanks to the background studies and the fiducialisation cuts analyses, the NRs from internal background are expected to be reduced to 16 per year, a negligible contribution with respect to the 772 coming from external sources (see previous Section). As the discrimination between ERs and NRs becomes very high above 20 keV in an imaging TPC (see Section 3.4.1 and [ 137 ] ), it possible to obtain a highly pure sample of external neutron induced NRs. About 200 NRs above 20 keV induced by external neutrons are expected to be detected in four months of data taking. • 10 cm Cu+ 40 cm water . To strongly suppress the external neutron interaction, a water shield of 40 cm thickness will be built around the copper layer. In this configuration, the internal radioactivity will be the dominant component of the background recoils (see last two rows of Table 3.4 ). Ten months are planned to be spent in the measurement of background data, to assess in detail the internal contributions to the background and to cross-check it with the MC simulations. 3.6 Future of CYGNO The goal of the CYGNO project is to boost the advancement of gaseous TPCs for directional DM searches. Thus, the construction in the future of a large \mathcal{O} (30) m 3 detector for the DM studies is a key milestone for the directional detector community. To achieve this goal, CYGNO is proceeding through a staged approach that involves the realisation of a 0.4 m 3 demonstrator CYGNO-04 towards a \mathcal{O} (30) m 3 experiment. In the following Sections, these two future CYGNO phases will be discussed. 3.6.1 Phase_1: CYGNO-04 Taking advantage from the experience gained from the construction, underground installation and operation of the LIME prototype, the CYGNO collaboration is moving towards the development of a PHASE_1 0.4 m 3 experiment demonstrator: CYGNO-04. The main objectives of PHASE_1 are to study and minimise material radioactivity on a realistic experimental layout and scale, while demonstrating the scalability and the actual potentialities of a large PHASE_2 detector to reach the expected physics goals. Figure 3.20: Technical design of CYGNO Phase_1 adapted to the Hall F space granted to the CYGNO collaboration. CYGNO-04 technical design report was submitted to LNGS administration and funding agencies in July 2022. It will be installed in Hall F and a technical design of the detector adapted to the experimental space is shown in Figure 3.20 . The technical design of the internal structure of the detector is shown in Figure 3.21 . This will be contained in a PMMA acrylic vessel to lower the material radioactivity, to avoid the gas contamination and to guarantee the electrical insulation from the internal electrodes. As shown in Figure 3.21 , the gas volume is split into two chambers, each of 50 cm drift length sharing a central cathode electrode in a back-to-back configuration. Exploiting the expertise gained by the DRIFT collaboration, the cathode will be manufactured from a 0.9 \mu m thick aluminised Mylar® film [ 224 , 225 ] . Indeed, the aluminium coating does not introduce radioactive material and the thinness of the film allows the alpha particles from radon daughter decays to enter the fiducial volume and thereby provide a means to tag and remove these events. To further reduce the internal background, the field cage will be manufactured from a Kapton™ foil with very thin layers of copper acting as rings. This technique was employed by DRIFT [ 224 ] and removes the necessity for the highly radioactive ceramic resistors used in conventional field cages, while at the same time reducing the amount of copper. The amplification stage covers an area of 50 \times 80 cm 2 with monolithic triple 50 \mu m thin GEMs. A cleaning procedure for GEMs based on DI water baths developed by T-REX collaboration will be utilised, to further suppress the radioactive contamination of this component [ 226 ] . The optical readout consists in six PMTs and two sCMOS camera per side to cover all the amplification area. The model foreseen is the Hamamatsu R7378A which has a good 15% QE at large wavelength like 550 nm [ 227 ] . The typical radioactivity of a PMT combined with the distance these sensors will be positioned in, makes their contribution to the background budget negligible. The Hamamatsu ORCA QUEST will be used as sCMOS camera. This novel sensor displays improved noise performances with respect to the ORCA Fusion (see Table 3.1 ), about 0.27 electrons RMS. This permits each pixel to perform a single photon counting while the sensor images maintain a nice effective granularity of \sim 200 \times 200 \mu m 2 per pixel in this setup. Given the large 40 K contamination measured in the camera lens, customised ones, manufactured from ultra pure silica (SUPRASIL®), are under development for CYGNO-04 in collaboration with external companies. This will allow to reduce of a factor \sim 10 4 the radioactive contribution from these objects. The collaboration is aiming at suppressing the radioactive contribution from the sCMOS camera, by customising the readout electronics which can be positioned outside the shields and by replacing the protective glass window of the sCMOS sensor with an ultra pure silica one. Figure 3.21: Technical design of CYGNO Phase_1. The 0.4 m 3 volume is split in two chambers which share a common aluminised Mylar® cathode. Four sCMOS cameras and twelve PMTs constitute the optical detectors which image the 50 \times 80 cm 2 readout area. A very preliminary GEANT4 simulation of the expected background in CYGNO-04 resulting from external environmental contribution plus internal material intrinsic radioactivity was performed in order to optimise the shielding material selection. The preliminary shield choice, which also takes into account the limited space available in Hall F, comprises 10 cm of copper surrounded by 1.1 m of water which is expected to lower the external radioactive contribution down to a factor \sim 20 below the internal one. Given the modular design of CYGNO-04 and the results on the fiducial cuts discussed in Section 3.5.2.3 , a similar capability of background reduction is expected to be achieved by fiducialization. To add on this, preliminary studies on gamma background rejection with Deep Neural Network algorithm based on track shape variables extracted from the sCMOS images suggests a 98.3% rejection in the whole [1-40] keV ee range with 40% nuclear recoil efficiency. The advancement in sCMOS camera sensitivity and the addition of the PMT information can further significantly improve these preliminary results, as well as the use of Convolutional Neural Networks combining sCMOS and PMT information. Therefore, a level of background after all selection cuts and rejection of the order 10-100 events/year in the 1-20 keV ee region for CYGNO-04 can be anticipated. CYGNO-04 TDR was submitted in July 2022 and approved by LNGS management and funding agency. 3.6.2 Phase_2: CYGNO-30 Figure 3.22: Preliminary technical design of a possible CYGNO Phase_2 located in the Hall C of the underground laboratories of LNGS. A CYGNO-30 experiment would be able to give a significant contribution to the search and study of DM with masses below 10 GeV/c 2 for both SI and SD coupling. In case of a DM observation claim by other experiments, the information provided by a directional detector such as CYGNO would be fundamental to positively confirm the Galactic origin of the allegedly detected DM signal. CYGNO-30 could furthermore provide the first directional measurement via elastic scattering on electrons of solar neutrinos from the pp chain, possibly extending to lower energies the Borexino results [ 228 ] . A more detailed analysis of the sensitivity to WIMP DM searches of an exposure of \mathcal{O} (100) kg year directional detector is presented in Chapter 7 . In addition to DM, such an experiment will be relevant also for neutrino physics. The CE \nu NS constitute the basic interaction behind the neutrino fog, see Section 2.2 . While the exposure of a \mathcal{O} (30) m 3 is not enough to reach the sensitivity necessary to detect Solar neutrino events through this interaction, new physics in the neutrino sector can modify the CE \nu NS cross section at low energies and increase the rate of events by orders of magnitude [ 229 , 230 ] . Even more interesting is the scattering between neutrinos and electrons. Classical DM experiments that are not sensitive to the direction of the detected events cannot distinguish ERs induced by solar neutrino from the ones from natural radioactivity [ 181 ] . A directional detector like CYGNO can instead exploit the directional information to identify the ERs caused by solar neutrino interaction, which display a strongly peaked asymmetry in their angular distribution, a feature not present in ERs from background sources. In fact, tonne-scale TPCs were proposed in the past with this same goal [ 231 , 232 ] . Incidentally, the CF 4 gas present in the CYGNO mixture has a large electron density (about 10 21 cm -3 ) with respect to its average low Z, which limits the multiple scattering of electron recoils in the gas. This is very important, as the multiple scattering hinders the recognition of the original direction for low energy ERs. In the CYGNO gas mixture, 1 ER per year per m 3 induced by Solar neutrinos of the pp cycle is expected above 20 keV {}_{\text{ee}} . A dedicated algorithm inspired by X-ray polarimetry studies [ 233 ] demonstrated on MC simulation that a 30 ∘ 2D angular resolution with 80% HT recognition is achievable at this energy threshold. On top of this, the 20 keV threshold translates into 80 keV of the incoming neutrino energy. This opens a new window of opportunities on the pp Sun processes down to low energy, unreachable to conventional neutrino detectors, such as Borexino, whose minimum neutrino energy measured is 160 keV [ 231 ] . Figure 3.22 shows the sketch of a possible configuration of a 30 m 3 CYGNO Phase_2 detector. Together with a rough estimation of 2 \cdot 10 3 m 3 of shields, it would fit inside the Hall C of the underground laboratories of LNGS. 3.6.2.1 R&D for the Phase_2 A possible way to increase the sensitivity in the low WIMP mass region at the same energy threshold is the use of very light elements in order to enhance the momentum transfer, as discussed in Section 2.1.4 . Therefore, the collaboration is studying the possibility of introducing hydrogen in the CYGNO gas mixture by adding a small percentage of either iC 4 H 10 or CH 4 . While observed that both gases mildly reduce the photon/electron ratio production, when methane is employed the overall amplification system results more stable and the voltages on the GEMs can be increased by \sim 70 V to obtain a larger light yield without compromising the stability of the detector. The optical readout needs very large gain from the amplification stage as only a small fraction of the solid angle is covered by these sensors. Maximising the light production is fundamental to lower and be sensitive to low WIMP masses, see Section 2.2 . The possibility of introducing a strong electric field below the outermost GEM to increase the production of photons is studied. Details on the amplification stage optimisation are described in Chapter 5 . 3.6.3 INITIUM INITIUM (Innovative Negative Ion Time projection chamber for Underground dark Matter searches) is an ERC Consolidator Grant with the goal of realising Negative Ion Drift operation within the CYGNO optical approach and results therefore highly synergic with it. The NID is a modification of the conventional TPC operation and will be extensively described in Chapter 6 . It consists in the addition of a highly electronegative dopant which captures the primary electrons in the gas within few hundreds of \mu m so that anions are drifted in place of electrons, reducing the diffusion to the thermal limit. The goal of INITIUM is to develop a scintillating He:CF 4 :SF 6 -based gas mixture at atmospheric pressure with a low content of SF 6 for NID operation in order to preserve the main features of the CYGNO experiment while minimising the diffusion and hence improve the tracking capability. If NID can be achieved within the optical approach, tracking could be even further improved by the possibility of reconstructing the track shape along the drift direction by sampling the recorded light at a kHz frame rate. At the moment, no camera exists with such a high rate which keeps high resolution and low noise. Nevertheless, given the fast development of the sCMOS technology, progress in short time is possible, which could open the door to this possibility. Chapter 4 Data analysis The CYGNO experimental approach is based on the optical readout of the light produced by the electron avalanche process induced by the GEM amplification stage (see Chapter 3 ). This is realised by the simultaneous use of photomultiplier tubes (PMTs, sensitive to the track evolution along the drift direction z ) and sCMOS cameras, that provide information on the track projection on the amplification plane ( x-y ). While a comprehensive analysis of the PMTs waveforms is still under development in the CYGNO collaboration, a dedicated preliminary algorithm has been elaborated for the analysis of the Negative Ion Drift data presented in Chapter 6 , in order to deal with the peculiar features of the PMT signals of this original operating conditions. This will be discussed in Section 6.3.1.1 , to better contextualise it in the Negative Ion Drift operation context. The sCMOS camera images represent a novel format of data in the context of Time Projection Chambers (TPCs) readout, and therefore require a tailored and original analysis strategy. A dedicated track reconstruction algorithm has been developed by the CYGNO collaboration for this task, with contributions from the work illustrated in this thesis. All the results from the analysis of sCMOS images reported in Chapters 5 and 6 are based on this algorithm, that represent the subject of this Chapter. Section 4.1 is dedicated to the description of the methodology used to reconstruct particles tracks from the camera pictures, and to its optimisation. Section 4.2 describes the analysis algorithm developed for this thesis to extract the actual x-y shape of 5.9 keV electron recoils from 55 Fe X-rays absorption in the gas for the diffusion studies presented in Chapter 5 . Section 4.3 illustrates the approach employed to measure the transversal dimension of alpha tracks for an alternative evaluation of diffusion parameters in the context of Negative Ion Drift operation (see Chapter 6 ). 4.1 Reconstruction code The ionisation patterns released by the passage of tracks inside the active gas volume of CYGNO detectors and recorded by the sCMOS camera can vary a lot in shape and photon density. Minimum Ionising Particles (MIPs), like muons from cosmic rays, will leave long, scarcely dense trails. Electrons of tens of keV will generate curly tracks quite dense close to their end point, while nuclear recoils will produce short, straight and dense shapes due to the large energy loss per unit length. The method to reconstruct tracks from sCMOS images needs therefore to be flexible enough to efficiently infer such diverse set of patterns. For this reason, the sCMOS images analysis procedure develops through three steps, by firstly dealing with the intrinsic sensor noise (Section 4.1.1 ), subsequently finding basic clusters from single small deposit (Section 4.1.2 ), and finally merging them into superclusters to determine the full tracks (Section 4.1.3 ). The output of the reconstruction code is the collection of pixels belonging to each found track, with their original position in the CMOS image and the number of counts measured by each pixel. A quantity proportional to the energy released by the recoiling particle can be obtained by summing the content of all the pixels associated to each track. In addition, the 2D projection on the amplification x-y plane of the ionisation trail topology and its dE/dx along the track can be inferred from the single pixels content. This is the paramount feature of sCMOS images, which give access to the track direction and sense measurement, and to particle identification capability by the analysis of track energy loss and spatial development. As illustrated in Section 3.1.3.2 , each sCMOS camera has different performances and characteristics. Since the ORCA-Fusion was employed for all of the results discussed in this thesis, it will be used as a reference for the following discussion. It is, nonetheless, important to stress that the reconstruction code is versatile with respect to this, and can be adapted to any camera model by a proper optimisation of the free parameters of the algorithm. 4.1.1 Sensor noise reduction Every picture of the sCMOS camera is effectively a matrix of 2304 \times 2304 integers representing the raw ADC counts recorded by each pixel. The thermal energy, the manufacturing process and the electrical connections are all potential sources of noise during the readout of the charge collected in each pixel. In order to proper deal with such issue in the images analysis, a set of pure noise images is acquired with the GEMs turned off every time physics data are collected (since the noise can change with time). As a consequence, these pictures will only contain the peculiar noise of each pixel. These are called pedestal runs. From these noise pictures it is possible to evaluate the average noise per pixel of about 99 and the standard deviation of 3.5. The distribution of the noise counts is roughly Gaussian with a tail at large values which depends on a pixel per pixel basis, but is negligible for the vast majority of them (>98%) and are often located at the borders of the sensor. The information of average noise ( \mu_{noise,ij} ) and standard deviation ( err_{noise,ij} ) for each pixel is stored in a matrix, called pedestal map . For each acquired image from physics run, a pixel by pixel subtraction of the pedestal map is performed. In addition, the pixels that satisfy the condition shown is Equation 4.1 are removed, C_{i,j}-\mu_{noise,i,j}T(r_{E}) , with m_{X} the mass of the new particle), the escaping flux will be semirelativistic with a velocity distribution approximately Maxwell-Boltzmann at the temperature of the energy sphere. The Maxwell-Boltzmann distribution exhibits a roughly order-one spread in velocities (i.e. \sim 75\% of the distribution lies between v=0.5\bar{v} and v=1.5\bar{v} where \bar{v}\approx\sqrt{T/m_{X}} is the average speed). This spread in velocities leads to a spread in arrival times of these particles at Earth. For a supernova a distance d away, the spread in arrival time is \Delta t\approx(d/\bar{v})\delta v with \delta v\equiv\frac{\Delta v}{v}\approx 1 . Consider a supernova that occurs in the centre of the Milky Way ( \sim 3000 light years away). The DM flux will be produced over \sim 10 seconds (the cooling timescale of the PNS), but the arrival on Earth of the bulk of the flux will take place over \sim 3000(c/\bar{v}) years. Since Type II supernovae are predicted to occur in the Galaxy at a rate of roughly 2 per century [ 303 ] , the emissions of \gtrsim 100 SN will all be overlapping at Earth at any given time. These overlapping emissions produce what can be called the "diffuse galactic flux" of hot dark matter produced in supernovae (SNDM). While the term “diffuse” is used to indicate that this flux is approximately constant in time, it is not isotropic. It is instead very strongly peaked towards the centre of the Galaxy, which is where the majority of supernovae take place. To quantify this, the double-exponential profile of [ 304 ] is utilised for the core-collapse SN density rate in our galaxy: \frac{dn_{SN}}{dt}=Ae^{-r/R_{d}}e^{-|z|/H} (7.19) with R the galactocentric radius and z the height above the Galactic mid-plane. Earth sits at R_{E}=8.7 kpc and z_{E}=24 pc. The parameter values are provided by [ 304 ] for Type II SN: R_{d}=2.9 kpc, H= 95 pc. The SN rate is normalised to two SN per century. The flux along a given line of sight is computed by performing the following integration: \Phi(\psi,\phi)=\\ N_{X}\int_{0}^{\infty}\frac{dn_{SN}}{dt}\biggm\lvert_{\left\{\begin{subarray}{{\\ }}r=\sqrt{r_{E}^{2}+(l\cos\psi)^{2}-2r_{E}(l\cos\psi\cos\phi)},\\ z=z_{E}+l\sin\psi\end{subarray}\right\}}\penalty\ dl (7.20) with \psi and \phi the polar and azimuthal angles respectively and N_{X} the total number of SNDM particles emitted by a single SN. In Figure 7.7 , the result of this computation is displayed with N_{X} divided out, as it simply adjusts the normalisation. Figure 7.7: Sky map for the flux of light DM produced by Galactic SNe. The scale has been normalized by N_{X} , the total number of DM particles produced in a single supernova. It is evident that the increased rate of SNe in the Galactic centre results in a large flux from that region. Note that the expected flux looking directly out of the plane of the Galaxy is four orders of magnitude smaller than the flux coming from the Galactic centre. It can be seen that the flux of DM due to supernovae is strongly peaked towards the Galactic centre. The flux from this region exceeds that of the flux coming from directly out of the plane by four orders of magnitude. Note that for this entire discussion, the focus was on supernovae occurring within the Galaxy. It is natural to ask about whether there is an isotropic contribution to this flux due to extragalactic supernovae, which is, for example, how the diffuse supernova neutrino background is formed [ 303 ] . However, the neutrinos are all travelling at c , which means that they experience no time-spreading effect. For massive particles, the time-spreading effect becomes so large on extragalactic scales that the corresponding flux, even integrated out to high redshift, is subdominant to the Galactic flux. Another line of sight integral can be performed as specified by [ 303 ] : \Phi=N_{X}\int_{0}^{\infty}R_{SN}(z)\left|\frac{dt}{dz}\right|\penalty\ dz (7.21) where R_{SN}(z) is the redshift-dependent Type II supernova rate (taken from [ 303 ] ) and (\frac{dt}{dz})^{-1}=H_{0}(1+z)\sqrt{\Omega_{\Lambda}+\Omega_{m}(1+z)^{3}} . Performing this integral and dividing by N_{X} as above, it is valid that \log_{10}(\Phi/N_{X})\approx-56.3 . Note that this is an order of magnitude below even the weakest line of sight for the Galactic contribution (directly out of the plane). As a result, the isotropic extragalactic contribution is ignored for the remainder of the study. To summarise the preceding discussion, the production of an anisotropic constant flux of high-momentum particles by Galactic SNe is a generic feature of any DM model with mass \mathcal{O}(10)-\mathcal{O}(100) MeV/c 2 and coupling to the SM sufficient to diffusively trap the particle within the PNS out to \sim 10-20 km. 7.2.1.2 Scattering kinematics and WIMP comparison In the standard WIMP picture, WIMPs have masses of \mathcal{O}(10)-\mathcal{O}(100) GeV/c 2 [ 105 ] , three orders of magnitude greater than the SNDM discussed in the previous Section. However, direct detection experiments built to target WIMPs are actually sensitive to SNDM as well. This is due to the simple fact that the cosmological abundance of WIMPs travel at the Galactic virial velocity ( v\approx 10^{-3}c ) while the SNDM travels at some order-one fraction of c . The semi-relativistic velocity of the SNDM compensates for its lighter mass and results in a similar momentum to a cold GeV/c 2 -scale WIMP. Equation 2.17 displays the momentum of a recoiling target nucleus in a DM detector with no assumptions that the momentum transfer is non-relativistic. In the case of MeV/c 2 -scale DM travelling semirelativistically, it is valid that m_{A}\gg m_{\chi},p_{0} . Hence: q\approx 2p_{0}\cos\theta_{r}. (7.22) It can immediately be noted that combining Equation 7.22 with the equivalent for WIMPs (Equation 2.18 ), it can be deduced that a nucleus will have the same recoil momentum if hit by a WIMP or a SNDM particle if p_{0}=v\mu_{A} (7.23) with v being the velocity of the incoming WIMP. This poses a significant challenge. One would wish to be able to discriminate between a cold GeV/c 2 -scale WIMP and hot SNDM if some signal were to be detected. Unfortunately, since \mu_{A}v in the WIMP scenario and p_{0} in the SNDM scenario can be of comparable order, even if one were able to generate large statistics on the recoil energy distribution in a detector, it would be very difficult to discriminate between the two models. Differences will show up in the recoil spectrum due to differences in the shape of the incoming momentum spectrum, but both are approximately Boltzmann and there is considerable uncertainty on the WIMP velocity distribution [ 99 ] and momentum spectrum of the SNDM that could limit discrimination. Just how difficult it is to discriminate these models with energetic information alone will be quantified in Section 7.2.6 . The best discriminator is the fact that, as will be explicitly shown in the following Sections, the SNDM is highly anisotropic, with a steep peak towards the Galactic centre. WIMPs, in contrast, appear to originate from the Cygnus constellation (see Section 2.3 ). This means that the signals from SNDM and from a cosmological abundance of WIMPs would be perpendicular . In this way, directional detection can allow to discriminate these two populations with a very small number of events. 7.2.1.3 SNDM model In order to evaluate the expected signal from the SNDM in a fiducial experiment (introduced in Section 7.2.3 ), a specific example model of SNDM that produces the features discussed in Section 7.2.1.2 will be described. (This is the same model as used in [ 302 ] .) Namely, it is a dark sector with a Dirac fermion coupled to the SM via the four-fermion operator \mathcal{L}\supset\frac{e\epsilon g_{d}}{\Lambda^{2}}\bar{\chi}\gamma_{\mu}\chi J^{\mu}_{\text{em}} (7.24) with \chi the dark matter and J^{\mu}_{\text{em}} the electromagnetic current of the SM. This can be viewed as the case wherein the dark sector is coupled to the SM by a dark photon with mass \Lambda and kinetic mixing \epsilon and a dark charge g_{d} . \Lambda is taken as \gg\mathcal{O}(10) MeV large such that it is not produced on-shell in the SN. The coupling is further parametrised to the SM by the variable y\equiv\frac{\epsilon^{2}g_{d}^{2}}{4\pi}\left(\frac{m_{\chi}}{\Lambda}\right)^{4} [ 305 ] . As a result of this choice of coupling term, the predominant interaction that keeps the dark sector thermally coupled to the SM is scattering with electrons. It is the radius at which this interaction ceases to become efficient that the temperature of the escaping DM is set (the "energy sphere" described in Section 7.2.1.1 ). This is defined formally by finding the radius r_{E} at which the optical depth for this interaction ( \tau_{E} ) is 2/3: \tau_{E}|_{r=r_{E}}\equiv\int_{r_{E}}^{\infty}\sqrt{\lambda_{\chi e}^{-1}(r)[\lambda_{\chi p}^{-1}(r)+\lambda_{\chi e}^{-1}(r)]}\penalty\ dr=\frac{2}{3} (7.25) where \lambda_{\chi p} and \lambda_{\chi e} are the mean free path for DM scattering with protons and electrons respectively. This condition simply provides a mathematical prescription to determine at what radius the SNDM decouples from the SM thermal bath. At radii rr_{E} , the electron density has dropped to the point at which the average SNDM particle will escape to infinity without undergoing any more electron scatters. The optical depth computed in Equation 7.25 is roughly the number of scatters expected for a SNDM particle to undergo as it escapes. For this reason, when it drops below unity (or, more formally, 2/3 [ 306 ] ), this simply means that SNDM particles emitted at that radius will not exchange energy with the SM bath and will not be thermally coupled to the SM. Instead, their temperature will be set at the last radius at which they were thermally-coupled to the SM, which is just the definition of the "energy sphere". So, as stated previously, it is the local temperature of the SM bath at this energy sphere that sets the temperature of the escaping SNDM flux, which in turn sets the momentum spectrum of incident SNDM at an Earth-based detector. 2 2 2 Note that the proton scattering appears in the formula as the SNDM is still undergoing diffusive scatters off of the protons that do not exchange energy even once the electron scatters have become inefficient. For further details, see [ 302 ] . 7.2.1.4 SNDM recoil spectrum The spectra of the recoils induced by SNDM particles can be computed starting from the same conditions in Equation 2.2 : \frac{dR}{dq^{2}d\Omega}=\frac{N_{0}}{A}\frac{d\sigma}{dq^{2}d\Omega}v\frac{\rho_{0}}{m_{\chi}}f(\vec{v})d^{3}v=\frac{N_{0}}{A}\frac{\rho_{0}}{m_{\chi}}\frac{d\sigma}{dq^{2}}\frac{1}{2\pi}\int\delta\left(\cos\theta-\frac{q}{2p}\right)vf(\vec{v})d^{3}v, (7.26) where the kinematic condition has been modified accordingly. As the SNDM particles are semi-relativistic, the most general representation of their momentum distribution in natural units is the Fermi-Dirac’s: f(\vec{p})d^{3}p=f(p)d^{3}p=\frac{\beta}{e^{\frac{\sqrt{p^{2}+m^{2}}}{T}}+1} (7.27) with T the temperature of the thermal equilibrium reached inside the region in the SN collapse at the moment of decoupling, and \beta a normalisation factor. As the interest is to express the momentum distribution at the laboratory, the gravitational effects these particles are subject to during the escape from the SN must not be neglected. As described in [ 307 ] , the gravitational redshift changes the particles momentum as follows: p_{*}=\sqrt{\frac{p^{2}+2\Phi m^{2}}{1-2\Phi}} (7.28) with p_{*} the momentum on the surface of the star. \Phi is the redshift parameter which depends on the star mass, being \Phi\equiv\int_{r_{E}}^{\infty}\frac{m_{enc}(r)}{r}dr , where r_{E} is the energy sphere and m_{enc} is the mass enclosed in a radius r . As a consequence not all particles can escape the SN core, but a minimum momentum is required. As a consequence, the modified distribution function of the SNDM particles momentum which arrive on Earth is f_{*}(p)=\begin{cases}p<0&0\\ p>0&\frac{1}{e^{\frac{\sqrt{\frac{p^{2}+m^{2}}{1-2\Phi}}}{T}}+1}\end{cases} (7.29) Due to the high degree of anisotropy in the angular distribution discussed above, the flux of particles is approximated as being produced from a point source at the Galactic centre. In addition, since the semi-relativistic speed of the SNDM particles is much larger than the velocity of the Sun, no transformation of coordinates is required as the laboratory is still with respect to the SNDM particles. Applying all these considerations into Equation 7.26 , the spectra of SNDM induced recoils is: \frac{dR}{dEdcos\theta}\propto\frac{1}{(1-2\Phi)^{3/2}}\int S(E)\delta(cos\theta-\frac{\sqrt{2m_{A}E}}{2p})\sqrt{\frac{p^{2}+2\Phi m_{\chi}^{2}}{p^{2}+m_{\chi}^{2}}}f_{*}(p)dp (7.30) For a more detailed calculation the reader is sent to Appendix C . 7.2.2 Frequentist statistical approach For the discrimination of two models of DM, the standard frequentist approach with the likelihood ratio test is opted for because very robust and reliable. The frequentist inference statistics is well described in text books as [ 308 , 309 ] . Let assume a generic set of n independent quantities \vec{x} are used to describe the state of a system or the outcome of a measurement. f(\vec{x}) is defined as the probability density function for which the following characteristics are valid: • f(\vec{x})d\vec{x} is the normalised occurrence of the state to have the vector {x_{1},x_{2},..,x_{n}} in a multidimensional infinitesimal volume \{[x_{1},x_{1}+dx_{1}],[x_{2},x_{2}+dx_{2}],...,[x_{n},x_{n}+dx_{n}]\} . • \int_{D}f(\vec{x})d\vec{x}=1 , where D is the domain of the f . The normalised occurrence of an event in the first item can be interpreted as the probability of the state to be found in that particular region of the parameter space, but this approach is not interested into the probability of an event, but on its possible repetition. For example, when considering a mono-dimensional problem, if \int_{0}^{10}f(x)dx=0.4 it means that if the same experiment were repeated an infinite amount of times, the outcome of the measurement would be 40% of the times in the range between 0 and 10, but states nothing about the probability of the underlying phenomenon. Considering experimental measurements it is very common to define the likelihood function \mathcal{L}=\mathcal{L}(\vec{x},\vec{a},H) , which is a function that represents the likelihood of the data set with a theoretical model that is expected to describe system considered. \vec{x} is the vector representing the data, \vec{a} the one representing parameters of the model and H is the hypothesis under which \vec{a} depicts the model. In general, by definition, the higher the likelihood the more the data agree with the model. Figure 7.8: Mock example of the possible density distributions of a discriminating variable y in case of two hypotheses H_{0} and H_{1} . The distribution in blue is the one that follows the hypothesis H_{0} , while the green one follows H_{1} . The red line represents the y_{0} , value chosen as the discrimination. When trying to discriminate between two different models, once a set of events is measured, the two hypotheses are named H_{0} and H_{1} . The analysis consists in finding a variable (or a set of variables) y=y(\vec{x}) so that its density distributions for the two models, g_{H_{0}}(y) and g_{H_{1}}(y) , are as separated as possible, i.e. with the least part the domain of y for which both g_{H_{0}} and g_{H_{1}} are different from zero. Once the distributions are set, a value of y=y_{0} determines the separation between the acceptance of hypothesis 0 and 1. Figure 7.8 represents a mock example of what described up to now. The blue distribution is the g_{H_{0}} , the green one is g_{H_{1}} , the red vertical line is y_{0} . If the measurement \vec{x} will result in yv_{lab}\cos\gamma}^{\infty}ve^{-\frac{v^{2}}{v_{p}^{2}}}dv (A.6) and finally, I=\frac{\alpha v_{p}^{2}}{2}e^{-\frac{\left(\frac{\sqrt{2m_{A}E}}{2\mu_{A}}-v_{lab}\cos\gamma\right)^{2}}{v_{p}^{2}}}, (A.7) In this calculation the escape velocity was not included. Following [ 76 ] , and using the complete version of f(\vec{v}) : f(\vec{v})=\alpha^{\prime}e^{-\frac{v^{2}}{v_{p}^{2}}}\Theta(v_{esc}-|\vec{v}+\vec{v_{lab}}|), (A.8) the integral turns out to be: I=\frac{\alpha^{\prime}v_{p}^{3}}{2v_{lab}}\left(e^{-\frac{\left(\frac{\sqrt{2m_{A}E}}{2\mu_{A}}-v_{lab}\cos\gamma\right)^{2}}{v_{p}^{2}}}-e^{-\frac{v_{esc}^{2}}{v_{p}^{2}}}\right)\Theta\left(\cos\gamma-\frac{\frac{\sqrt{2m_{A}E}}{2\mu_{A}}-v_{esc}}{v_{lab}}\right), (A.9) Appendix B Global gain analysis In Section 5.3.1 , Equation 5.2 , which expresses the reduced gain \Gamma as a function of the reduced field \Sigma , was obtained from [ 242 , 243 ] and is here reported for simplicity: \Gamma=\frac{ln(G)}{n_{g}pt}=A\left(\frac{V_{GEM}}{n_{g}pt}\right)^{m}exp\left(-B\left(\frac{n_{g}pt}{V_{GEM}}\right)^{1-m}\right), (B.1) with n_{g} the number of GEMs used in the amplification stage, p the gas pressure, t thickness of the GEM, V_{GEM} total voltage applied to the GEMs and m , A , B free parameters. In addition, the reduced field \Sigma is defined as: \Sigma=\frac{V_{GEM}}{n_{g}pt} (B.2) In Section 5.3.1 , the parameter m is always approximated with the value of 1 as the gain scans do not span over a large range of voltages, hence of reduced fields. However, to have a wider view on the correctness of the amplification modelling, it is interesting to compare the data taken with the same gas mixture of He:CF 4 at 60/40 and different stacking option (see Table 5.2 ). This way, due to the change in thickness and number of GEMs, the reduced field varies much more than when only the voltage across the GEMs is modified. The average reduced gain and field obtained averaging the results of the three different amplification configurations are displayed in Figure B.1 , with errors calculated from the propagation of the uncertainties on the 55 Fe peaks and on the working pressure. In this context, the reduced gain \Gamma can be written as a function of the reduced field \Sigma as (for m=1 , akin to Equation 5.5 ): \Gamma=A_{0}+B_{0}\Sigma=\frac{(\Sigma-\Sigma_{0})}{D} (B.3) and (for m=0 ): \Gamma=A_{2}e^{-\frac{B}{\Sigma}} (B.4) where \Sigma_{0} , D , A_{2} and B are the free parameters. The fits with the right-hand side of Equation B.3 (in blue) and Equation B.4 (in red) to the average reduced gain of the three different GEM configurations are shown in Figure B.1 and the fitted parameters are reported in Table B.1 . Both curves well represent the data points, showing that the reduced fields explored in this study do not allow to determine m for this gas mixtures and GEM configurations. This result is consistent with the expected operation of the GEM amplification structures, as discussed in the work presented in [ 242 ] . Figure B.1: The reduced light gain as a function of the reduced field. The data points are obtained with the average value of gain and field of the three different configurations of amplification at 60/40 of He:CF 4 . The two fitting curves represent the extreme function obtained from Equation B.1 . m Par0 Par1 \chi^{2}/NdF 0 2.8\pm 0.3 134\pm 15 0.5/1 1 26\pm 7 102\pm 10 0.07/1 Table B.1: Table summarising the results of the fit with Equation B.4 and Equation B.3 to the data in Fig. B.1 . For m=0 {Par0,Par1} = { A_{2} [1/(Torr cm)], B [V/(Torr cm)]}, while for m=1 {Par0,Par1} = { \Sigma_{0} [V/(Torr cm)], D [V] }, with the corresponding unit of measurements. Appendix C SNDM differential spectrum calculation In this appendix the derivation of the double differential spectrum of the SNDM induced nuclear recoils is calculated. Equation 7.26 displays the double differential rate in momentum transfer and solid angle. Utilising the general Fermi’s Golden rule to make explicit the differential cross section it is obtained: \frac{dR}{dq^{2}d\Omega}=\frac{N_{0}}{A}n_{SNDM}\frac{1}{2\pi}\int\frac{\sigma_{SNDM,A}}{4p^{2}}\delta\left(\cos\theta-\frac{q}{2p}\right)vf(\vec{v})d^{3}v, (C.1) with n_{SNDM} the number density of SNDM particles close to the laboratory location and \sigma_{SNDM,A} is the cross section between the dark fermion and the nucleaus of mass number A . The value of the cross section is highly model dependent. According to the discussion in [ 302 ] , the temperature T of thermal equilibrium and the coupling factor y between the dark fermion and the SM particles are related each other again depending on the specific model. As the purpose of this calculation in the context of the thesis is to compute the shape of the energetic and angular spectra for a SNDM particle (see Section 7.2 ) the overall multiplicative constants are irrelevant for the evaluation. Since the velocity v is linked to the momentum p relativistically, the velocity distribution can be rewritten in terms of momenta. Moreover, the integral of the velocity v has to be performed on the modified momentum distribution due to the gravitational redshift as in Equation 7.29 and 7.28 . As a result the following relation is obtained: \frac{dR}{dq^{2}d\cos\theta}\propto\int S(q)\frac{1}{p^{2}}\delta\left(\cos\theta-\frac{q}{2p}\right)\frac{p/m_{\chi}}{\sqrt{1+(p/m_{\chi})^{2}}}p_{*}^{2}f_{*}(p_{*})dp_{*}d\Omega_{p}, (C.2) Now, it is possible to integrate on the angular part in the phase space and on the azimuthal angle of the recoil. In addition to this, writing the p_{*} terms as a function of the p at the laboratory: \frac{dR}{dEd\cos\theta}\propto\frac{1}{(1-2\Phi)^{3/2}}\int S(E)\delta\left(\cos\theta-\frac{\sqrt{2m_{A}E}}{2p}\right)\sqrt{\frac{p^{2}+2\Phi m_{\chi}^{2}}{p^{2}+m_{\chi}^{2}}}f_{*}(p)dp, (C.3) which is used in Equation 7.30 . If one wishes to continue the calculation to derive the single differential rates, p can be made the principle variable of the Dirac’s delta, \delta\left(\cos\theta-\frac{\sqrt{2m_{A}E}}{2p}\right)=\delta\left(p-\frac{\sqrt{2m_{A}E}}{2\cos\theta}\right)\frac{p}{\cos\theta} and the integral on p solved exploiting the properties of the delta function. Appendix D Schneider Xenon Lens technical sheet See pages 1-2 of Componenti/Appendix_D.pdf