The In Situ Electrochemical−Chemical Cascade Strategy for Pyruvic Acid Synthesis Xueli Mei, Huawei Zhuo, Yu Liu, Lili Wang, Yudai Huang, Hongtao Xie, Yizhao Li Abstract Hydrogen peroxide (H2O2), as a green oxidizing medium, can be generated and utilized in situ via an electrochemical–chemical cascade, enabling organic transformations while enhancing efficiency and selectivity. However, balancing high H2O2 production, efficient activation, and selective substrate conversion remains challenging. Herein, a series of transition metal‐doped CeO2 catalysts were developed for electrocatalytic H2O2 generation and its subsequent use in converting α‐hydroxy acids to pyruvate. Among them, Ni−CeO2 exhibited the best performance, achieving a pyruvate production rate of 19.9 mmol g−1 h−1 and a Faradaic efficiency of 55.3%. Mechanistic studies revealed that transition metal doping regulates the local coordination environment and oxygen vacancy concentration, thereby optimizing the adsorption strength of the *OOH intermediate, which governs the two‐electron oxygen reduction reaction pathway and H2O2 generation and release. Furthermore, in situ generated H2O2 was selectively activated on the catalyst surface to form a reactive oxygen species network dominated by hydroxyl radicals (·OH) and assisted by singlet oxygen (1O2). Among these, ·OH showed the lowest energy barrier for α‐C─H bond activation and subsequent electron rearrangement, making it the key species for pyruvate formation. This work provides a new strategy for the preparation of value−added chemicals. By employing an “unsaturation−oxygen coordination engineering” strategy, the local coordination environment is regulated to achieve efficient electrochemical synthesis of H2O2. Importantly, an electrochemical−chemical coupled cascade strategy is utilized for the efficient preparation of pyruvic acid via lactic acid oxidation. Introduction Pyruvic acid is a crucial platform molecule with extensive applications in fields such as food, medicine, agriculture, and bioenergy. It also serves as a key intermediate and metabolic hub in various biochemical reactions. Therefore, the development of efficient and sustainable pyruvate production strategies has long been an important topic in chemistry and chemical engineering [, , ]. At present, the industrial production of pyruvate mainly relies on biological fermentation and enzymatic catalysis. Although biological fermentation offers advantages such as renewable feedstocks and environmental friendliness, it requires stringent sterile conditions and process control, while also suffering from metabolic inhibition, complex separation and purification procedures, and high overall costs. Enzymatic catalysis, although highly selective and operable under mild conditions, is still limited by catalytic efficiency and long‐term stability [, , , ]. Therefore, the development of green and efficient non−biological conversion pathways is of great significance for overcoming the limitations of existing processes. In recent years, cascade reactions for the synthesis of value‐added chemicals have attracted increasing attention. For α‐hydroxy acids, selective oxidation can directly produce the corresponding α‐keto acids; thus, the conversion of lactate to pyruvate can serve as a representative model system. Electrocatalytic oxidative upgrading of biomass platform molecules provides a sustainable route for the production of high‐value‐added oxygenated chemicals, in which substrate adsorption, reactive oxygen species generation, and electrode material properties play important roles in determining reaction selectivity [, , ]. Hydrogen peroxide (H2O2) [, , , ], as a green oxidant, can be generated in situ through the electrocatalytic two‐electron oxygen reduction reaction (2e‐ORR). Compared with conventional oxidation systems using externally added H2O2, the in situ generation strategy can avoid the transportation, storage, and purification of H2O2, while enabling the continuous supply and immediate utilization of the oxidant during the reaction process, thereby providing a new approach for the green and selective oxidation of organic molecules [, ]. However, most current studies on H2O2 electrosynthesis mainly focus on the efficient generation and accumulation of H2O2 itself, while the correlations among its in situ activation, ROS evolution, and subsequent selective conversion of organic substrates within the same reaction system remain insufficiently understood [, , , ]. The selective generation of H2O2 via 2e‐ORR and its further efficient conversion into ·OH are two key steps that determine the efficiency of cascade oxidation []. Therefore, how to effectively couple electrocatalytic H2O2 generation, controllable activation, and organic oxidation is a key issue in constructing an efficient electrochemical−chemical cascade system. However, the efficient coupling of H2O2 generation with selective oxidation remains intrinsically challenging. On the one hand, in situ generated H2O2 is prone to disproportionation or further reduction, limiting its utilization efficiency. On the other hand, the reactive oxygen species (ROS) generated during H2O2 activation typically exhibit complex and uncontrolled evolution behavior, and competition among different ROS pathways often leads to nonselective oxidation, thereby limiting the selective formation of target products. Therefore, achieving synergistic regulation among H2O2 generation, ROS evolution, and organic substrate conversion is the key scientific issue in constructing efficient cascade systems. Ceria (CeO2) is considered an ideal platform for regulating H2O2 activation and ROS evolution due to its reversible Ce3+/Ce4+ redox couple, abundant oxygen vacancies (OV), and excellent oxygen‐migration capability [, ]. In recent years, studies on rare‐earth‐based ORR catalysts have shown that the unique electronic structures, defect‐regulation capability, and interfacial electronic effects of rare‐earth elements can significantly influence oxygen adsorption, electron transfer, and ORR pathway selection []. On this basis, introducing transition metal single‐atom sites is expected to further modulate the local coordination environment and electronic structure, thereby enabling control over the adsorption behavior of key intermediates and ROS generation pathways [, , , , , ]. Previous studies have shown that regulating the local coordination environment of atomically dispersed metal sites can effectively modulate the adsorption behavior of oxygen‐containing intermediates and the ORR pathway selection, providing an important basis for the design of highly selective 2e‐ORR catalysts []. However, the intrinsic mechanism by which catalyst local structure influences ROS distribution and subsequently determines organic reaction selectivity remains unclear. Accordingly, herein we propose an “unsaturated oxygen coordination number” regulation strategy and construct a series of transition metal (Mn, Fe, Co, Ni) single‐atom catalysts on a CeO2 support to achieve efficient electrocatalytic H2O2 generation and its directed utilization in organic transformations. Using lactate as a model substrate, a 2e‐ORR‐organic oxidation cascade system was established to realize the highly selective conversion of lactate to pyruvate. Among these catalysts, Ni−CeO2 exhibited the best performance, affording a pyruvate yield of 19.9 mmol g−1 h−1 with a Faradaic efficiency (FE) of 55.3%. Combined with in situ electron paramagnetic resonance and quenching experiments, hydroxyl radicals (·OH), superoxide radicals (·O2 −), and singlet oxygen (1O2) were clearly detected in the system. Among them, ·OH played a dominant role in lactate oxidation, whereas 1O2 exhibited a pronounced synergistic effect. Theoretical calculations further revealed that the decomposition of H2O2 into ·OH possesses the lowest energy barrier, followed by the 1O2 pathway. During the subsequent reaction process, the α−C–H activation step involving ·OH exhibited the lowest reaction barrier, thereby dominating the pyruvate formation pathway. These experimental and theoretical results collectively reveal the intrinsic relationship between ROS evolution pathways and reaction selectivity. This work proposes a design principle for directing ROS evolution by regulating the local coordination structure at the mechanistic level, achieving the deep coupling of electrocatalytic in situ H2O2 generation with the valorization of biomass−derived molecules, and providing important guidance for the integration of electrocatalytic H2O2 utilization with biomass−derived molecule conversion. Results Characterization of Catalyst Structure A series of transition metal‐doped CeO2 catalysts (TM−CeO2, TM = Mn, Fe, Co, Ni) were successfully synthesized (Figure ). All catalysts exhibited uniform spherical nanoparticle morphologies with regular structures and porous surfaces, which are beneficial for mass transfer and the exposure of active sites (Figures and ). High‐resolution transmission electron microscopy (HRTEM) images clearly revealed the (111) lattice fringes of CeO2, and slight changes in the lattice spacing after doping indicated that the introduced transition metals induced subtle lattice distortion (Figure ). In addition, Ce, O, and the doped metals (Mn, Fe, Co, Ni) were uniformly distributed throughout the support without obvious aggregation (Figure ). Combined with mass spectrometry (ICP−MS) results, the metal contents in all samples were confirmed to be at relatively low levels (Table ). To further confirm the dispersion state of the active sites, aberration‐corrected transmission electron microscopy (AC‐TEM) was employed to characterize Ni−CeO2. The results showed that Ni [, ] was anchored on the CeO2 matrix in the form of isolated single atoms (as indicated by the yellow circles in the image), and its three‐dimensional elemental mapping further confirmed the atomic dispersion of Ni (Figure ). All samples displayed characteristic diffraction peaks corresponding to the cubic fluorite structure of CeO2 (Figure ). The slight shift in diffraction peaks after doping indicates that the transition metals were successfully incorporated into the lattice and altered the lattice parameters. In the Raman spectra (Figure ), the characteristic F2g mode of CeO2 appeared at approximately 460 cm−1 []. After doping, this peak exhibited a slight red shift and broadening, indicating enhanced lattice distortion and increased OV concentration. In addition, Ni−CeO2 possessed the highest specific surface area and exhibited a hierarchical micro‐mesoporous structure, whereas the other samples mainly displayed microporous characteristics (Figure and Table ). This hierarchical pore structure (Figures and ) not only facilitates the exposure of more active sites but also promotes the rapid transport of O2, H2O2, and organic substrates at the catalytic interface. To reveal the effect of doping on the surface electronic structure, X‐ray photoelectron spectroscopy (XPS) analysis was conducted (Figure ). The survey spectra confirmed the successful incorporation of all transition metal elements into the CeO2 support. Ce 3d spectra (Figure ) showed the coexistence of Ce4+ and Ce3+ species [, ]. Compared with pure CeO2, the Ce 3d peaks of the doped samples shifted toward lower binding energies, indicating electron transfer from the transition metals to CeO2 and an increase in the electron density around Ce sites. Correspondingly, the O 1s peaks (Figure ) associated with lattice oxygen (OL) and OV shifted toward higher binding energies, further suggesting significant electron redistribution in the system. Quantitative analysis of the Ce3+ ratio (Figure ) showed that transition metal doping markedly increased the Ce3+ content, and the variation trend was highly consistent with the OV concentration obtained from electron paramagnetic resonance (EPR) measurements (Figure ). In addition, high‐resolution Ni 2p, Mn 2p, Fe 2p, and Co 2p spectra (Figure ) demonstrated that all transition metals existed in multiple valence states, indicating strong electronic interactions between the metals and the support. Such strong interactions not only stabilize the single‐atom dispersion state but also regulate the local electronic structure, thereby providing a crucial electronic basis for the subsequent reactions. X‐ray absorption fine structure (XAFS) analysis was further employed to investigate the atomic‐scale coordination environment. The absorption edge position (Figure ) of Ni−CeO2 was between those of Ni foil and NiO, closer to NiO, indicating that the average oxidation state of Ni is close to +2. In the Fourier−transformed EXAFS (FT‐EXAFS) spectrum (Figure ), only a prominent Ni─O coordination peak was observed at approximately 1.38 Å, while no Ni−Ni scattering signal was detected, confirming the isolated single‐atom dispersion of Ni. Moreover, the Ni─O bond length was determined to be 1.98 Å with a coordination number of approximately 5.8, significantly lower than that of an ideal octahedral coordination environment, indicating a coordinatively unsaturated structure accompanied by local lattice distortion and OV formation [, , ] (Figures , and , and Table ). Only the Ni−O feature was observed in the wavelet‐transformed EXAFS (WT−EXAFS) spectrum (Figure ), further excluding the possibility of metal aggregation. The Fe K‐edge XANES spectrum (Figure ) shows that the absorption edge of Fe−CeO2 lies between those of FeO and Fe2O3, approaching Fe2O3, indicating that Fe predominantly exists in the +3 oxidation state. The FT−EXAFS (Figures , and ) spectrum reveals an Fe−O bond peak at ∼1.3 Å, with no Fe−Fe bond signal, confirming the atomic dispersion of Fe [, ]. K‐edge analyses of Mn and Co (Figures , and ) also confirmed their single‐atom dispersion on the CeO2 surface, although their coordination numbers differed significantly (Mn: 3.5, Fe: 4.3, Co: 2.0, Ni: 5.8), reflecting tunable local coordination environments (Figure and Tables ) [, ]. Among them, Co−CeO2 exhibited the lowest coordination number and the highest OV concentration, which is consistent with the EPR results. Notably, the degree of local coordinative unsaturation and OV concentration jointly determine the adsorption and activation mode of O2. Excessive OV concentrations tend to promote the dissociative adsorption of O2, whereas moderately coordinatively unsaturated structures are more favorable for stabilizing molecularly adsorbed intermediates, thereby promoting the 2e‐ORR pathway. These results establish the intrinsic relationship among coordination structure, OV, and O2 activation mode, providing a critical structural basis for subsequent H2O2‐selective generation and ROS evolution. Electrocatalytic 2e‐ORR Performance To ensure a fair comparison of the catalytic behavior among different transition metal centers, the dopant content of all TM−CeO2 catalysts was uniformly fixed at 3%. This value was determined based on a systematic screening of Ni−CeO2−X% (X = 1%, 2%, 3%, 5%), in which RRDE results demonstrated that 3% doping delivered the optimal H2O2 selectivity (Figure ), thereby excluding the influence of metal loading differences on the reaction pathway. In both 0.01 M and 0.1 M KOH electrolytes, Ni−CeO2 exhibited the best activity and H2O2 selectivity. In 0.1 M KOH, it displayed an onset potential of 0.65 V versus RHE (defined at −0.1 mA cm−2) [], close to the theoretical equilibrium potential (0.7 V vs. RHE), and a Tafel slope of only 51.7 mV dec−1, indicating rapid kinetics with nearly zero overpotential (Figure ). Ni−CeO2 achieved an H2O2 selectivity of 84%−92% within the potential range of 0−0.5 V versus RHE, with an electron transfer number close to 2, clearly following a 2e− reaction pathway (Figure ). Further Koutecky−Levich (K−L) analysis also showed that the electron transfer number of Ni−CeO2 was close to 2, further confirming from a kinetic perspective that it preferentially generates H2O2 through the 2e‐ORR pathway (Figure ). Notably, H2O2 selectivity does not show a simple linear relationship with the oxygen‐vacancy‐related defect concentration, but instead exhibits a distinct defect−window effect (Figure and Table ). An appropriate amount of oxygen vacancies is beneficial for O2 activation and *OOH intermediate formation, whereas excessive oxygen vacancies lead to the over‐adsorption of oxygen‐containing intermediates and promote the competing 4e−ORR pathway. In this TM−CeO2 catalyst series, the suitable oxygen‐vacancy‐related defect level is approximately 3.5 × 1015 spins g−1. Although Mn−CeO2 and Ni−CeO2 possessed similar electrochemically active surface areas (ECSA) (Figure ), the latter exhibited significantly higher H2O2 selectivity, indicating that the reaction pathway is primarily governed by *OOH adsorption behavior rather than the number of active sites. At a current density of 40 mA cm−2, the H2O2 yield of Ni−CeO2 reached 3.5 mol g−1 h−1 (FE = 92.6%) and 1.9 mol g−1 h−1 (FE = 89.1%) in 0.1 M and 0.01 M KOH, respectively, both of which were markedly superior to those of the other TM‐CeO2 catalysts (Figures ). Considering that O2 mass transfer limitations in conventional H‐type cells significantly restrict the H2O2 yield [, ], a flow‐cell reactor was further employed to enhance gas–liquid–solid interfacial mass transfer (Figures and ). Under conditions of 0.1 M KOH and 40 mA cm−2, the H2O2 yield and FE of Ni−CeO2 increased to 9.9 mol g−1 h−1 and 98.6%, respectively, significantly outperforming the other doped catalysts (Figures , and ). Importantly, the H2O2 yield showed a positive correlation with the metal–oxygen (M–O) coordination number, indicating that the degree of coordinative unsaturation plays a decisive role in regulating the 2e‐ORR pathway (Figure ). The performance of this catalyst surpasses that of most reported systems (Figure ), highlighting its remarkable advantage for efficient H2O2 electrosynthesis. In addition to high activity, catalyst stability is equally important. Under a current density of 40 mA cm−2, Ni−CeO2 operated continuously for 320 h with almost no voltage decay (Figure ), while its morphology and crystal structure remained unchanged (Figures and ), indicating excellent electrochemical and structural stability as well as good durability over a wide current density range. In situ attenuated total reflection surface−enhanced infrared absorption spectroscopy (ATR−SEIRAS) was employed to monitor the key intermediates. In both 0.01 M and 0.1 M KOH electrolytes (Figures and ), the O−O stretching vibration signal of O2 was observed at approximately 1490 cm−1, indicating that the pre‐adsorption of O2 molecules is the initial step of the reaction []. In 0.1 M KOH, when the potential decreased below 0.8 V versus RHE, the characteristic peak at approximately 1270 cm−1 corresponding to the O−O stretching vibration of the *OOH intermediate and the signal at approximately 834 cm−1 assigned to M−O vibrations appeared simultaneously and continuously intensified with further negative potential shift [, ]. In contrast, in 0.01 M KOH, these same signals could only be detected at more negative potentials (<1.2 V vs. RHE), indicating that higher alkalinity facilitates the formation of *OOH and accelerates its surface conversion process. In summary, by constructing moderately coordination−unsaturated single−atom sites, Ni−CeO2 stabilizes the key *OOH intermediate and efficiently guides the reaction along the 2e‐ORR pathway, achieving highly selective electrochemical H2O2 synthesis. Additionally, it provides a continuous and controllable source of oxidants for the subsequent selective oxidation of lactic acid to pyruvic acid. Electrocatalytic Lactate Oxidation and ROS‐Regulated Mechanism Building upon the efficient in situ H2O2 electrosynthesis system, the performance of TM‐CeO2 catalysts toward the selective oxidation of lactate was further evaluated. Using lactate as the model substrate, an electrochemical–chemical cascade system was constructed in 0.01 M KOH electrolyte to realize the in situ generation and immediate utilization of H2O2. Considering the decisive role of H2O2 activation in determining the reaction pathway, different Fe‐based cocatalysts, including ferric citrate, EDTA–Fe, Fe3O4, and FeCl2, were further introduced to promote the conversion of H2O2 into ROS (Figures and ). High−performance liquid chromatography (HPLC) analysis showed that FeCl2 exhibited the most pronounced promotional effect and significantly enhanced pyruvate production efficiency. This result indicates that Fe2+ can efficiently activate the in situ generated H2O2 and produce ROS through a Fenton‐like process, thereby driving the subsequent oxidation reaction. To exclude the dominant influence of Cl− on the reaction pathway, FeSO4 was used as a chloride−free Fe2+ source for the control experiment (Figure ). With the same Fe2+ dosage, the FeSO4 system could still promote lactic acid conversion and generate pyruvic acid, indicating that pyruvic acid formation mainly originates from the activation of in situ generated H2O2 by Fe2+, rather than depending on the participation of Cl−. The performance difference between the FeSO4 and FeCl2 systems may be related to the influence of different counter anions on the effective state and stability of Fe2+. Therefore, FeCl2 was employed as the cocatalyst in all subsequent studies. Under optimized conditions, different TM−CeO2 catalysts exhibited markedly different catalytic behaviors. Ni−CeO2 displayed the best performance, delivering a pyruvate yield of 19.9 mmol g−1 h−1 with a FE of 55.3%, which was significantly superior to those of CeO2 and TM−CeO2 (Figures , and ). This trend is highly consistent with their H2O2 generation capability in the 2e−ORR process, indicating that the overall efficiency of the cascade system depends not only on the H2O2 generation rate but also on its subsequent activation behavior. In addition, comparison of the byproduct distribution in the TM‐CeO2 catalyst systems showed that, besides the target product pyruvate, a small amount of acrylic acid was also detected, indicating that lactate may undergo competitive dehydration/oxidation side reactions mediated by ROS. Among them, the Fe−CeO2 and Ni−CeO2 systems produced lower amounts of acrylic acid, with formation rates of 2.4 and 2.2 mmol g−1 h−1 after 50 h of reaction, respectively, indicating that these two catalysts are more inclined to generate pyruvate through the selective oxidation pathway. In contrast, the acrylic acid formation rates in the Mn−CeO2 and Co−CeO2 systems reached 3.2 and 3.5 mmol g−1 h−1, respectively, suggesting that they are more prone to competitive dehydration/oxidation or nonselective side reactions. Due to the low catalytic activity of pure CeO2, no obvious byproducts were observed. Further comparison with the acetic acid standard calibration curve showed that no characteristic acetic acid peak was observed in the in situ cascade system, indicating that acetic acid is not a major byproduct in this system (Figure ). Total organic carbon (TOC) analysis further confirmed that the mineralization rate of the Ni−CeO2 system was only 14.7% (Table ), indicating that it can effectively suppress nonselective oxidation while preferentially maintaining the target product formation pathway. To further verify the role of the in situ H2O2 generation strategy, externally added commercial H2O2 was used as a control instead of in situ electrogenerated H2O2 (Figure ). Only a small amount of pyruvic acid was generated in the externally added H2O2 system, and the yield was significantly lower than that of the Ni−CeO2 in situ electrochemical−chemical cascade system. As the concentration of externally added H2O2 increased, pyruvic acid formation did not increase accordingly; instead, overoxidation‐related byproducts such as acetic acid were more readily detected. This indicates that one‐batch addition of commercial H2O2 makes it difficult to achieve effective matching among oxidant supply, ROS generation, and selective oxidation of lactic acid, whereas in situ electrogenerated H2O2 enables continuous supply and immediate utilization, which is more favorable for maintaining the target product formation pathway. In addition to high activity and selectivity, Ni−CeO2 also exhibited excellent stability. After continuous operation for 330 h at 40 mA cm−2, almost no decay in operating voltage was observed (Figure ), and the catalyst morphology and crystal structure remained unchanged before and after the reaction, demonstrating excellent structural stability and resistance to intermediate poisoning (Figures and ). Further analysis of the Fe and Ni contents in the electrolyte before and after the reaction showed that the Ni content after the reaction was only 0.021 mg L−1, indicating extremely low Ni leaching. In contrast, the Fe content decreased from 163.52 to 56.61 mg L−1, suggesting that effective Fe species may undergo consumption, deposition, or changes in the Fe2+/Fe3+ equilibrium during long−term operation (Table ). Therefore, the slight performance change is more likely related to changes in the effective concentration of Fe species and H2O2 activation efficiency, rather than damage to the bulk structure of Ni−CeO2. Furthermore, to verify the universality of this system, it was extended to other α‐hydroxy acid substrates. When L‐3‐phenyllactic acid and 2‐hydroxybutanedioic acid were used as substrates, phenylpyruvic (PPA) acid and 2‐oxobutanedioic acid (OAA) were generated, respectively, with yields of 9.9 and 8.1 mmol g−1 h−1 (Figure ) and corresponding FE of 27.6% and 22.7% (Figures and Table ). Compared with lactic acid, L‐3‐phenyllactic acid contains a bulky phenyl substituent, which may weaken its effective adsorption and mass transfer at the catalytic interface and reduce the efficiency of ROS attack on the α‐C−H site; therefore, its product formation rate and Faradaic efficiency decreased. In contrast, 2‐hydroxybutanedioic acid contains two carboxyl groups, which may form relatively strong coordination interactions with Ce sites or oxygen vacancies on the CeO2 surface under alkaline conditions, leading to restricted adsorption configurations or slower product desorption, thereby reducing the subsequent oxidation efficiency. These results indicate that this system has preliminary applicability to some representative α‐hydroxy acid substrates, but the molecular size, number of functional groups, adsorption behavior, and difficulty of α‐C−H activation of different substrates significantly affect their reactivity and selectivity. To reveal the intrinsic mechanism of selective lactate oxidation, the generation behavior and role of ROS during the reaction were systematically investigated. In situ EPR results showed that ·OH, O2 −, and 1O2 were gradually generated, and their signal intensities continuously increased as the reaction proceeded (Figure ). Furthermore, radical concentrations in the TM−CeO2 systems were measured after 50 h of reaction, and the results indicated that the concentrations of ·OH, ·O2 −, and 1O2 were all the highest in the Ni−CeO2 system (Figure and Table ). To further distinguish the specific roles of different ROS species, targeted quenching experiments were performed (Figures ). Upon the addition of isopropanol (IPA) as a ·OH scavenger, the pyruvate yield decreased by 83.5%, indicating that ·OH is the dominant reactive species driving lactate oxidation. When p−benzoquinone (BQ) was added to quench ·O2 −, the yield decreased by only 17.7%, suggesting that its contribution is relatively limited. In contrast, the addition of 1,4−diazabicyclo [2.2.2] octane (DABCO) to suppress 1O2 led to a 73.5% decrease in pyruvate yield. Although this inhibitory effect was weaker than that of ·OH, it still had a significant influence, indicating that 1O2 plays an important synergistic role in the reaction. Based on the above results, the in situ generated H2O2 was converted into ·OH, ·O2 −, and 1O2 in the presence of Fe2+. These reactive species subsequently interacted with lactate and underwent a series of intermediate evolution and electron rearrangement processes, ultimately leading to pyruvate formation (Figure ). Therefore, the Ni−CeO2 catalyst successfully established a coupled mechanism spanning in situ H2O2 generation, ROS evolution, and reaction pathway regulation, thereby constructing a reactive oxygen network dominated by ·OH with the synergistic participation of 1O2. Theoretical Insights Into Structure‐ROS‐Selectivity Correlation To reveal the regulatory mechanism of catalyst structure on reaction pathways at the atomic scale, density functional theory (DFT) calculations were employed to systematically investigate the 2e‐ORR process and its intrinsic correlation with subsequent selective oxidation of lactic acid (Figures ). The adsorption free energy of the *OOH intermediate (ΔG *OOH) was used as a descriptor to construct a volcano plot for 2e‐ORR activity (Figure ). The ΔG *OOH value of Ni−CeO2 (4.35 eV) was closest to the theoretical value (∼4.22 eV), achieving an optimal balance between reaction activity and H2O2 selectivity. Pure CeO2, with an excessively high ΔG *OOH (4.57 eV), restricted the formation of O2 → *OOH, exhibiting a high reaction energy barrier (1.62 eV) at 0.7 V versus RHE, thereby resulting in low activity. In contrast, Mn−CeO2 and Co−CeO2, due to overly strong *OOH adsorption, tended to promote O−O bond cleavage, favoring the 4e− pathway to generate H2O and significantly reducing H2O2 selectivity (Figure ). Combining XAFS and EPR results, it was further clarified that the differences in ΔG *OOH originated from changes in the local coordination environment and OV concentration induced by transition metal doping. Although OV could promote O2 adsorption and activation, an excessively high OV concentration led to excessive stabilization of *OOH, thereby inhibiting H2O2 desorption. Therefore, achieving a moderate degree of coordination unsaturation was crucial for maintaining the 2e‐ORR pathway. To further quantify the regulatory role of OV, Ni−CeO2 models with different OV concentrations, including single, double, and triple OV structures (Ni−CeO2, Ni−CeO2−2OV, Ni−CeO2−3OV), were constructed (Figures , and ). The results showed that as the OV concentration increased, ΔG* OOH decreased to −0.15 and −0.24 eV, respectively, indicating significantly enhanced adsorption compared to the single OV model. This suggested that excessive OV led to excessive stabilization of *OOH, hindering its desorption and weakening 2e‐ORR selectivity, further demonstrating that a moderate OV concentration was key to balancing O2 activation and H2O2 release. From the perspective of electronic structure, crystal orbital Hamiltonian population (COHP) analysis revealed the decisive influence of metal–oxygen bond strength on *OOH adsorption behavior (Figure ). The Co/Mn−CeO2 systems exhibited high −ICOHP values (−1.25/−1.239 eV), indicating stronger M 3d–O 2p hybridization, which resulted in overly strong *OOH adsorption and inhibited desorption. In contrast, Ni/Fe−CeO2 (−0.817/−0.827 eV) demonstrated moderate bond strength, facilitating a dynamic balance between adsorption and desorption. Pure CeO2, with weaker bonding (−0.789 eV), struggled to effectively stabilize reaction intermediates, leading to limited activity [, ]. Partial density of states (pDOS) analysis further showed that transition metal doping significantly narrowed the bandgap of CeO2 and increased the electron density near the Fermi level (Figures and ) [, ], thereby enhancing conductivity and promoting charge transfer processes. Among them, Ni−CeO2 exhibited a moderately increased electron density after introducing a single OV, which was beneficial for O2 adsorption and *OOH formation. However, under high OV concentrations, local electrons significantly accumulated in the Ni–OV region, significantly enhancing *OOH adsorption. Differential charge density analysis visually revealed this electronic regulatory mechanism (Figures and ). The single OV structure formed a moderate electron‐rich region, facilitating the maintenance of *OOH adsorption–desorption balance. In contrast, under high OV concentrations, excessive electrons localized between Ni and OV, leading to overly strong *OOH adsorption and inhibiting the 2e‐ORR pathway. On this basis, theoretical analysis was further extended to the subsequent lactic acid oxidation process. In this process, the radical generation capacity and its hydrogen abstraction ability from the α‐C−H bond were key steps determining the reaction rate and selectivity. H2O2 generated on the Ni−CeO2 surface preferentially decomposed to form ·OH, which had the lowest reaction energy barrier (Figures , and ). In comparison, the 1O2 pathway required higher energy, while the formation of ·O2 − involved a stepwise dehydrogenation process (H2O2 → OOH → O2 −) with multiple transition states, making it kinetically unfavorable. This trend was highly consistent with radical quenching experiment results, further indicating that ·OH was the dominant reactive oxygen species in the system. For the subsequent lactic acid oxidation process, lactic acid preferentially adsorbed on Ce sites near OV and reacted with reactive oxygen species in the adsorbed state (Figures and ). ·OH had the lowest reaction energy barrier for attacking the α‐C−H bond of lactic acid, making it the most likely to initiate lactic acid activation. In contrast, ·O2 − and 1O2 corresponded to higher reaction energy barriers. Although ·O2 − exhibited superior hydrogen abstraction ability from the α‐C−H bond compared to 1O2, its low concentration in the system due to its kinetically unfavorable generation process limited its overall contribution to the reaction. During the further electron rearrangement of lactic acid radicals and their conversion to pyruvic acid, the ·OH‐participating pathway still had the lowest energy barrier. Further comparison of the reaction behaviors of adsorbed lactic acid and solution‐state lactic acid shows that lactic acid adsorbed on the catalyst surface has a lower α‐C−H activation energy barrier (Figures and ), indicating that the oxidation of surface‐adsorbed lactic acid is energetically more favorable and may be one of the important reaction pathways for lactate conversion. Considering that Fe2+−mediated H2O2 activation can also generate ROS in the solution phase, the current results more reasonably suggest that both the surface adsorption pathway and the solution‐phase ROS oxidation pathway may jointly participate in this cascade reaction. In summary, a unified structure‐reaction correlation mechanism can be established. Transition metal doping regulates the adsorption behavior of the *OOH intermediate by modulating the local coordination environment and OV concentration, thereby determining H2O2 generation and release. Furthermore, the in situ generated H2O2 decomposes on the catalyst surface to form a ROS network dominated by ·OH and synergized by 1O2, ultimately regulating the reaction pathway and pyruvic acid selectivity of lactic acid. Conclusion In summary, this work has constructed an electrochemical–chemical cascade system based on single‐atom TM−CeO2 catalysts, achieving the conversion of O2 to H2O2 and subsequently to the selective oxidation of lactic acid into pyruvic acid. Systematic studies demonstrate that transition metal doping can modify the adsorption behavior of the *OOH intermediate by regulating the local coordination environment and OV concentration, thereby determining the 2e‐ORR pathway and H2O2 production efficiency. Among them, Ni−CeO2 achieves an optimal balance between O2 activation and H2O2 desorption due to its moderate coordination unsaturation structure and OV concentration, thus exhibiting the highest H2O2 selectivity and production rate. Furthermore, the in situ generated H2O2 is efficiently activated by Fe2+ to form a ROS network dominated by ·OH and synergized by 1O2. Here, ·OH plays a leading role in activating the α‐C−H bond of lactic acid and facilitating subsequent electron rearrangement, serving as the key reactive species driving pyruvic acid production. Experimental results, together with DFT calculations, collectively indicate that Ni−CeO2 can effectively couple H2O2 generation, ROS evolution, and reaction pathway regulation, ultimately achieving efficient and highly selective oxidation of lactic acid. This work provides a novel design strategy for utilizing electrocatalytically in situ generated H2O2 to drive the high‐value conversion of biomass platform molecules. Contributor Information Yudai Huang, Email: huangyd@xju.edu.cn. Hongtao Xie, Email: xieht@csj.uestc.edu.cn. Yizhao Li, Email: liyizhao0809@126.com.