Analyzing the influence of variable viscosity and thermal radiation on heat and mass transfer of MHD bioconvective nanofluid flow through surface regression model Authors: Shantha Sheela J, David Maxim Gururaj A Published: 2026 ABSTRACT The present study explores the impacts of significant parameters on the flow characteristics through sensitivity analysis of magnetohydrodynamic (MHD) bioconvection nanofluid flow considering variable viscosity. Using the Runge-Kutta fourth-order technique, the set of governing equations is transformed into nonlinear coupled ordinary differential equations. The analysis focuses primarily on how various parameters, including thermophoresis, Brownian motion, variable viscosity, magnetic field, thermal radiation parameter, bioconvection Lewis number, bioconvection Peclet number, and others, influence the density profiles of microbes, temperature, and concentration. These profiles are detailed and graphically depicted. Finally, the parameters that have the most significant impact on the desired output are examined. The concluded results are applied in various fields, such as microfluidics and biological systems (like nutrient transport in aquatic environments), bioengineering, bio-nano coolant systems, and biofuel cells. Introduction The studies on bioconvection nanofluid flow are mostly applied in industrial and commercial items like biofuel and biofertilizers1. Numerous distinct metabolic characteristics of cyanobacteria and eukaryotic microalgae are beneficial for the production of biofuel2. Therefore, bioconvective phenomena can be used in many scientific and technological fields. Thus, bioconvection in nanofluid flow has attracted a lot of attention from researchers and scientists lately3. One exciting development in fluid mechanics and heat transport is the use of nanofluids. From electronics cooling to energy systems, nanofluids have the potential to improve an extensive range of applications by improving the heat transfer and thermal conductivity characteristics of base fluids. Most of the researchers have observed that the nanofluids have better effectiveness on convective heat transfer than that of base fluids. Hilledson et al.4 and Kuznetsov5 have discussed the concept of nanofluid bioconvection in detail. The stability of a nanofluid under both oscillatory and non-oscillatory instability conditions of nanofluid flow, including oxytactic microorganisms, is demonstrated by Kuznetsov6. Additionally, magnetohydrodynamics is familiar for its technical applications, such as the cooling of nuclear reactors and cooling and heating chambers, astrophysical flows, open water reservoirs, and other environmental and economic improvements. It finds considerable usage in engineering and physics, particularly in the design of gas turbines and space technologies. Moreover, applications in geophysics, astrophysics, oil drilling, thermal recovery, and underground nuclear waste storage facilities motivated many researchers to work on this concept. Bakier7 examined the impact of thermal radiation from a vertical surface on mixed convection in a porous material. Hossain and Takhar8 studied the forced and free convection flow and explored how radiation influences flow on issues related to heat transfer. The effects of radiation heat transfer and transverse magnetic fields were examined by Damseh9 in order to perform a numerical analysis of mixed convection in magnetohydrodynamics. In a study, Zahmatkesh10 investigated how thermal radiation causes the temperature to be distributed almost consistently throughout the vertical sections of an enclosure. Hayat et al.11 worked on magnetohydrodynamic (MHD) steady nanofluid flow through a rotating disc. Ahmad et al.12 offered an inclusive analysis of how nanoparticles move through porous medium with gyrotactic organisms over an extensive surface. In comparison to the circumstances of constant properties, viscosity plays a significant role in the flow property of fluids, and the flow characteristics undergo substantial alterations when the effects of variable viscosity are considered. Literally, analysis of viscosity is quite significant for determining the thermofluidic behavior of heat transfer fluids. Seddeek13 registered the impacts of variable viscosity and radiation on unsteady MHD flow over a semi-infinite flat plate. Soundalgekar et al.14 investigated the impacts of variable viscosity on boundary layer flow with variable surface temperature. Mohammad et al.15 studied heat and mass transfer along a vertical cylinder with variable viscosity effects. MHD boundary layer flow with temperature-varying fluid properties has been examined by H. Konwar et al.16. The impact of mass and heat transmission in mixed convection flow with chemical reactions has been investigated by Zia Ullah17. In a porous media with varying viscosity, the rate of mass and heat transfer has been registered by A.S. Adeyemo et al.18. Mishra et al.19 worked on rotational microorganism magnetohydrodynamic nanofluid flow. Mondal et al.20 studied the entropy generation of variable viscosity and thermal radiation on magneto-nanofluid flow. Mishra et al.21 investigated the entropy optimization of various properties on MHD nanofluid flow. Mishra et al.22 studied the thermal radiation’s effect on a rotating vertical cone’s mixed convective unsteady nanofluid flow. Effects of magnetohydrodynamics on the flow of a three-dimensional nanofluid across a stretched surface in a porous medium: The effects of an unsteady mixed convection nanofluid flow were studied by Mondal et al.23. Mishra et al.24 used Sutterby nanofluid over a stretching surface with Brownian motion and a porous medium to discuss the effects of microbial activity. Although most of the prominent results on the impact of variable viscosity have been highlighted in the previous studies, they still need more attention. The technique of sensitivity analysis is used to ascertain how changes in a model’s or system’s input parameters might be linked to variations in the model’s or system’s output. By showing which parameters have the most effects on the behavior of the system, this method supports comprehending the relationship between the model’s parameters and the outputs that are produced. In experimental design, the Response Surface Methodology25,26, also known as the surface regression model, is a useful technique for analyzing problems where a response is influenced by several variables that optimize the response and assists in establishing a list of experimental designs for response prediction. In order to study a particular model term or interaction, it could be appropriate to modify the theoretical constraints. An important statistical method for determining the variability of specific variables’ performance in relation to the RSM model is ANOVA analysis, often known as the analysis of variance. The ANOVA analysis synthesis criterion is used to evaluate the accuracy of the RSM model using the following computing estimators: degree of freedom (DOF), sum of squares, adjusted mean square, F-value, and P-value. In addition to modeling fitness, an attempt would likely be made to explain the influence of parameters. Vahedi et al.27 registered sensitivity analysis on MHD forced convection of a Cu-water nanofluid flow across a wedge. Md. Faisal Md. Basir28 examined the sensitivity analysis of MHD nanofluid flow with binary chemical reaction. Priyadharshini M et al.29 examined the numerical and sensitivity study on MHD blood flow. Nonlinear radiative flow of a hybrid nanofluid across a stretching cylinder has been investigated numerically by Mohammed Ismail et al.30. Shantha Sheela J et al.31 studied bioconvection nanofluid flow considering nonlinear thermal radiation using response surface methodology. P MN, N SK32 registered the detailed study of two-dimensional Casson fluid flow on a stretching surface that is stable and embedded with trimetallic nanoparticles suspended in engine oil. S. Znaidia et al.33 examined the sensitivity analysis of optimizing radiative heat transfer in magnified radiative nanofluid flow past a melting surface with the effects of thermal conductivity and effective viscosity. Farooq et al. al.34 studied the flow characteristics and thermal performance in dihydrogen oxide-based nanofluid performance in PTSC. Farooq et al.35 investigates the unsteady flow of a hybrid nanofluid over a spinning disk in a porous medium under the influence of viscous diffusion. Motivated by the preceding studies, the authors intend to investigate MHD bioconvection nanofluid flow with variable viscosity effects, and sensitivity analysis is utilized to comprehend how different elements affect the system’s performance. Tables and graphs are demonstrated, and the results are discussed in detail for various pertinent parameters. Such research is novel and has not yet been accomplished, according to the best extensive research to date. Novelty of the research work The present study’s novelty is the implementation of nanoparticle-volume-fraction-dependent viscosity into the MHD nanofluid bioconvection model. Unlike previous constant-viscosity or temperature-dependent viscosity techniques, the current formulation adopts a ϕ-dependent viscosity model that introduces a direct and nonlinear connection between the momentum and concentration equations. Mathematical formulation This section discusses a steady two-dimensional bioconvection nanofluid flow with variable viscosity and a magnetic field (as pictured in Fig. 1). The fluid flow is considered to be in the x-axis and normal to the y-axis. The wall maintains the magnetic field of strength B\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_o$$\end{document}, the temperature T\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_w$$\end{document}, the concentration \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\phi _w$$\end{document}, and the density of microbes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$n_w$$\end{document}, each of which is most probably higher than \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_\infty$$\end{document}, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\phi _\infty$$\end{document}, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$n_\infty$$\end{document}, respectively. The current work’s physical model representation is shown in Fig. 1. The following governing equations of the present problem are stated as taken in36–38. Thus, consider v = (u,v)) where v is the nanofluid filtration velocity1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial u}{\partial x}+\frac{\partial v}{\partial y} = 0 \end{aligned}$$\end{document}The linearized momentum equation with a suitable choice of pressure is as follows:2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} -\frac{\mu }{K} {\textbf {v}} =-\sigma B_0^2 {\textbf {v}} -\nabla p -(1-\phi _{\infty })\rho f_{\infty } \beta g (T- T_\infty )+(\rho _{p}-\rho _{f_{\infty }})g (\phi -\phi _\infty )+g\gamma \Delta _{\rho }(n-n_\infty ) \end{aligned}$$\end{document}The momentum Eq. (2) has been reconstructed by eliminating p using cross differentiation. Hence,3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial ( u\mu )}{ \partial y} = {(1-\phi _{\infty })\rho f_{\infty } \beta g K}\frac{\partial T}{\partial y} -{(\rho _{p}-\rho _{f_{\infty })}g K} \frac{\partial \phi }{\partial y}-{g\gamma \Delta _{\rho }K} \frac{\partial n }{\partial y}-{\sigma B_0^2 K \frac{\partial u}{\partial y}} \end{aligned}$$\end{document}In Eq. (3), the viscosity of the nanofluid is examined according to the local volume fraction of nanoparticles39. As a result, the viscosity is expressed as4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{1}{\mu } = \frac{1}{\mu _\infty }(1+\delta (\phi - \phi _\infty )) \end{aligned}$$\end{document}and Eq. (4) can be written as5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{1}{\mu } = m_\mu (\phi - \phi _r) \end{aligned}$$\end{document}where,6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} m{_\mu } = \frac{\delta }{ \mu _\infty }, \phi _r = \phi _\infty - \frac{1}{\delta } \end{aligned}$$\end{document}In Eqs. (4) and (5) δ, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$m{_\mu }$$\end{document}, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mu _\infty$$\end{document}, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\phi _r$$\end{document}, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\phi _\infty$$\end{document} are constants.7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} u\frac{\partial T}{\partial x}+ v\frac{\partial T }{\partial y} = \alpha _m\nabla ^2T +\tau \left[ D_B\frac{\partial \phi }{\partial y} \frac{\partial T}{\partial y}+ \left( \frac{D_T}{T_{\infty }}\right) \left( \frac{\partial T}{\partial y}\right) ^2\right] -\frac{1}{(\rho c)_f}\frac{\partial q_r}{\partial y} \end{aligned}$$\end{document}8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{1}{\varepsilon }\left[ u \frac{\partial \phi }{\partial x} +v\frac{\partial \phi }{\partial y}\right] = D_B\frac{\partial ^ 2 \phi }{\partial y^2}+ \left( \frac{ D _T}{T_{\infty }}\right) \frac{\partial ^ 2 T}{\partial y^2 } \end{aligned}$$\end{document}9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial }{\partial x}\left[ nu+n\overline{u} - D_m\left( \frac{\partial n}{\partial x} +\frac{\partial n}{\partial y}\right) \right] +\frac{\partial }{ \partial y}\left[ nv+n\overline{v}-D_m\left( \frac{\partial n}{\partial x} +\frac{\partial n}{\partial y}\right) \right] = {0} \end{aligned}$$\end{document}Fig. 1Geometrical model of the problem. Geometrical model of the problem. The essential boundary conditions have the following form.10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \ v = 0, \; T= T_w,\; \phi = \phi _w,\; n= n_w \; at \; y= 0 \; \end{aligned}$$\end{document}11\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} T \rightarrow T_{\infty },\; \phi \rightarrow \phi _{\infty },\; n\rightarrow n_{\infty }, \;at\; y \rightarrow {\infty } \end{aligned}$$\end{document}Here, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta _ {\rho }$$\end{document} = \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\rho _ {m\infty }$$\end{document}- \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\rho _ {f\infty }$$\end{document}, and γ is the density difference between the microbes’ density and the density of the base fluid. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\alpha _ {m}$$\end{document} = \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$k_ {m}/(\rho {c_f})$$\end{document} is the thermal diffusivity, τ is the ratio of effective heat capacity of the nanoparticle to the heat capacity of the nanofluid, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\overline{u} =(b_{Wc}/{\Delta \phi })({\partial \phi }/{\partial x})$$\end{document}, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\overline{v} = (b_ {Wc}/{\Delta \phi }) ({\partial \phi }/{\partial y})$$\end{document}, and the nanoparticle volume fraction \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta {\phi } = \phi _ {w}- \phi _ {\infty }$$\end{document}. The Rosselland approximation provides the radiative heat flux expression40. As12\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} q_r= \frac{-4\sigma ^*\partial T^4}{3K^*\partial y} = \frac{-16T^3\partial T}{3K^*\partial y} \end{aligned}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\sigma ^*$$\end{document} and K\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^*$$\end{document} are the Stefan-Boltzmann constant and the mean absorption coefficient, respectively. The dimensional stream function ψ defined in such a way that13\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} u= \frac{\partial \psi }{\partial y} \; and \; v = - \frac{\partial \psi }{\partial x} \end{aligned}$$\end{document}The governing partial differential Eqs. (3) and (7)–(9) are changed into coupled nonlinear ODEs with the following transformations4114\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \eta = \frac{y}{x}P e_x ^\frac{1}{2}, \; f(\eta ) = \frac{\psi }{\alpha _m P e_x^\frac{1}{2}},\; \theta (\eta ) = \frac{T-T_{\infty }}{T_w -T_{\infty }}, \; s(\eta ) = \frac{\phi -\phi _{\infty }}{\phi _w-\phi _{\infty }}\;, \zeta (\eta ) =\frac{n-n_{\infty }}{n_w-n_{\infty }} \end{aligned}$$\end{document}The ordinary differential equations are given by Eqs. (15)–(18).15\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \left( \frac{Nv}{Nv - s} + M \right) f'' + \frac{Nv}{(Nv-s)^2}f's' - \lambda (\theta '- Nrs'-Rb\zeta ') = 0 \end{aligned}$$\end{document}16\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \theta ''[1+ Rd(1+(q-1))\theta ^{3}]-3Rd(q-1)(\{1 +(q-1)\theta \}^{2}\theta '^{2})+\frac{1}{2}f\theta ' + Nb \theta 's'+ N t\theta '^{2} = 0 \end{aligned}$$\end{document}17\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} s''+ \frac{Les'f}{2}+\frac{N t}{Nb}\theta '' = 0 \end{aligned}$$\end{document}18\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \zeta ''+ \frac{1}{2}Lb f\zeta '- P e (s'\zeta '+ \zeta s'')= 0 \end{aligned}$$\end{document}and the boundary conditions (10) and (11) are transformed into:19\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \eta = 0,\; f(0) = 0,\; \theta (0) =1 ,\; s(0) = 1,\; \zeta (0) = 1 \end{aligned}$$\end{document}20\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \eta \rightarrow \infty , \; f'\rightarrow 0,\; \theta \rightarrow 0,\;s \rightarrow 0, \zeta \rightarrow 0,\; \end{aligned}$$\end{document}where,21\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} {\left. \begin{aligned} Nr&=\frac{(\rho _{p}-\rho _{f \infty })(\phi _{w}-\phi _{\infty )}}{\rho _{f\infty } \beta (T_{w}-T_{\infty })(1-\phi _{\infty )}} \\ Nt&=\frac{\varepsilon \rho C_{p} D_{T}(T_{w}- T_{\infty )}}{(\rho c)_f\alpha _m T_{\infty }}\\ Nb&= \frac{\varepsilon \rho C_{p}D_{B}(\phi _{w}- \phi _{\infty )}}{(\rho c)_f\alpha _{m}}\\ Rb&= \frac{ \gamma \Delta _{p} (n_{w}-n_{\infty )}}{((1-\phi _{\infty })\rho _{f\infty } \beta (T_{w}-T_{\infty )}}\\ Le&=\frac{\alpha _{m}}{\epsilon D_{B}}\\ Lb&=\frac{\alpha _{m}}{D_{m}}\\ \end{aligned} \hspace{1cm} \begin{aligned} M&= \frac{\sigma \beta _0^2K}{\mu _\infty }\\ Nv&= -\frac{1}{\delta (\phi _w - \phi _\infty )} \\ Ra_{x}&= \frac{(1-\phi _{\infty })\rho _{f\infty } Kg\beta (T_w-T_{\infty })x }{\mu \alpha _m }\\ Pe_{x}&=\frac{U_{\infty } x}{\alpha _m}; Pe =\frac{b W_c }{D_m}\\ Rd&= \frac{16\sigma ^*T_{\infty }^{3}}{3k^{*}k_{m}};q=\frac{T_{w}}{T_{\infty}}\\ \lambda&= \frac{Ra_{x}}{P e_{x}} \end{aligned} \hspace{1cm} \right\} } \end{aligned}$$\end{document}The local Nusselt number, the local Sherwood number, and the local motile microbe density number are defined as22\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} Nu_x = \frac{x q_w}{k(T_w-T_\infty )}, \; Sh_x = \frac{x q_m}{D_B (\phi _w- \phi _\infty )}, \; Dm_x = \frac{x q_n}{D_m (n_w-n_\infty )} \end{aligned}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$q_w$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$q_m$$\end{document} are the surface heat and mass fluxes, respectively. In the present work, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Nu_x/(P e_x) ^{1/2}$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Sh_x / (Pe_x)^{1/2}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Dm_x /(Pe_x)^{1/2}$$\end{document} are also considered as local Nusselt number, local Sherwood number and local microbe density numbers, respectively, and considered in the form as follows:23\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} Nu_x/(P e_x) ^{1/2} = -\theta '(0),\; Sh_x / (Pe_x)^{1/2} = -s'(0),\; Dm_x /(Pe_x)^{1/2} = -\zeta '(0). \end{aligned}$$\end{document} Numerical solution The system of ODE (15)−(18) is solved numerically while taking into account the boundary conditions (19) and (20). First, the higher-order nonlinear differential equations are transformed into a set of first-order differential equations, which are detailed in the following sections.\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} f = f_1,\; f'= f_2,\;f'' = f_2',\; \end{aligned}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \theta = f_3,\; \theta ' = f_3',\; \theta ''= f_ 4' \end{aligned}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} s = f_5\; s' = f_5'\;s'' = f_6'\; \end{aligned}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \zeta = f_7\; \zeta ' = f_8\;,\zeta ''= f_8' \end{aligned}$$\end{document}This generates a system of initial value problems (IVP).24\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} f'' = f_2' = ((Nv-s))/(Nv+M(Nv-s)(\lambda (f_4- Nrf_6 -Rbf_8)- (Nvf_2 f_5'))/(Nv+M(Nv-s)(Nv-s)) \end{aligned}$$\end{document}25\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \begin{aligned} \theta = f_3,\; \theta ' = f_3'= f_4,\; \theta ''= f_ 4'= - (f_1f_4)/2-Nbf_4f_6)-Nt(f_4^2)\\ +3Rdf_4^2((1+q-1)f_3)^2(q-1))/(1+Rd(1+(q-1)f_3)^3\\ \end{aligned} \end{aligned}$$\end{document}26\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} s = f_5,\; s' = f_5' = f_6,\; s'' = f_6' = (-1/2(Lef_1f_6)) - \frac{Nt}{Nb}f_ 4' \end{aligned}$$\end{document}27\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \zeta = f_7, \;\zeta ' = f_7',\; = f_8,\; \zeta ''= f_8' = (-Lbf_1f_8)/2+ Pe((f_6f_8)+ f_7 f_6') \end{aligned}$$\end{document}The above-generated IVP corresponds to the following boundary conditions. The corresponding boundary conditions for the above-generated IVP are:28\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} f_1 = 1, f_2 = t_1,\; f_3 = 1,\; f_4 =t_2,\; f_5 = 1,\;f_6 = t_3,\;f_7 = 1,\; f_8 = t_4 \end{aligned}$$\end{document}The shooting method is used to solve Eqs. (24−(27), and the values of t\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_1$$\end{document}, t\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_2$$\end{document}, t\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_3$$\end{document}, and t\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_4$$\end{document} are initialized with an assumed value, and until convergence is reached, the iterations continue. In this approach, initial guesses are taken into account to determine convergence. The tolerances were fixed at RelTol = \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$10^-5$$\end{document} and AbsTol = \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$10^-5$$\end{document} to ensure numerical accuracy. The numerical simulations are carried out using MATLAB software. Validation Table 1 presents the comparative statistics regarding the influence of Pe and Nr on the rate of heat transfer for λ = 0.01 and Rb = 0, Nt = 0.5, and Nb = 0.5. Table 1Comparison table on the effect of Pe and Nr on the dimensionless heat transfer rate -θ '(0) for Rb=0 with Nt = 0.5, Nb = 0.5, M=0,and Lb = 1.RbPeO.A Beg et al36Present resultsNr=0.1Nr=0.5Nr=0.1Nr=0.500.010.05870.05750.05810.05760.050.05870.05750.05810.05760.10.05870.05750.05810.05760.50.05870.05750.05810.05761.00.05870.05750.05810.0576 Table 1Comparison table on the effect of Pe and Nr on the dimensionless heat transfer rate -θ '(0) for Rb=0 with Nt = 0.5, Nb = 0.5, M=0,and Lb = 1.RbPeO.A Beg et al36Present resultsNr=0.1Nr=0.5Nr=0.1Nr=0.500.010.05870.05750.05810.05760.050.05870.05750.05810.05760.10.05870.05750.05810.05760.50.05870.05750.05810.05761.00.05870.05750.05810.0576 Comparison table on the effect of Pe and Nr on the dimensionless heat transfer rate -θ '(0) for Rb=0 with Nt = 0.5, Nb = 0.5, M=0,and Lb = 1. The current work’s results are compared with36, and it is observed that the two sets of results agree, demonstrating the accuracy and validity of the current findings. The stability convergence analysis for grid spacings of 0.01 and 0.001 is given in Table 2. The grid convergence analysis indicates that there is no oscillation, and the developed numerical method is stable.Table 2Grid convergence analysis for h = 0.01 and 0.001.h = 0.01h = 0.001ηf’(η)θ(η)s(η)ζ(η)ηf’(η)θ(η)s(η)ζ(η)00.19211100.18991110.20100.24040.9290.80770.82390.20010.23810.92960.80730.82540.40200.27820.85280.63030.67070.40020.27420.85390.62930.67260.60300.30230.77110.46980.53790.60030.29660.77280.46780.53960.80400.31080.68370.32810.42330.80040.30490.68630.32460.424610.3030.59280.20970.3271.00050.29850.59390.20170.32561.2010.27810.49320.11040.24191.20060.27650.49490.10160.24061.4020.23560.3860.03580.16851.40070.2370.38820.02690.16751.6030.17520.2695− 0.1120.10491.60080.17820.2722− 0.01880.10421.8040.09620.1411− 0.02550.0491.80090.09910.1441− 0.03050.04901.9950.00270.0039− 0.00120.00121.9950.00270.0039− 0.00140.00142000020000 Table 2Grid convergence analysis for h = 0.01 and 0.001.h = 0.01h = 0.001ηf’(η)θ(η)s(η)ζ(η)ηf’(η)θ(η)s(η)ζ(η)00.19211100.18991110.20100.24040.9290.80770.82390.20010.23810.92960.80730.82540.40200.27820.85280.63030.67070.40020.27420.85390.62930.67260.60300.30230.77110.46980.53790.60030.29660.77280.46780.53960.80400.31080.68370.32810.42330.80040.30490.68630.32460.424610.3030.59280.20970.3271.00050.29850.59390.20170.32561.2010.27810.49320.11040.24191.20060.27650.49490.10160.24061.4020.23560.3860.03580.16851.40070.2370.38820.02690.16751.6030.17520.2695− 0.1120.10491.60080.17820.2722− 0.01880.10421.8040.09620.1411− 0.02550.0491.80090.09910.1441− 0.03050.04901.9950.00270.0039− 0.00120.00121.9950.00270.0039− 0.00140.00142000020000 Grid convergence analysis for h = 0.01 and 0.001. Grid point convergence analysis The stability convergence analysis for grid spacings of 0.01 and 0.001 is given in Table 2. The grid convergence analysis indicates that there is no oscillation, and the developed numerical method is stable. Results and dicussions The impact of parameters such as thermal radiation parameter (Rd), mixed convection parameter (λ), surface temperature parameter (q), Lewis number (Le), magnetic field parameter (M), variable viscosity parameter (Nv), bioconvection Rayleigh number (Rb), bioconvection Lewis number (Lb), and bioconvection Peclet number (Pe) on velocity, temperature, concentration, and microorganism density is extensively investigated, with suitable physical explanations provided by tables and graphs. The results are calculated using the parameters’ estimated values: M = 0.5, Nv = 2, Rd = 0.5, q = 0.1, λ = 1.2, Nr = 0.1, Nb = 0.2, Nt = 0.2, Le = 2.0, Lb = 2.0, Rb = 0.5, and Pe = 0.5. Impact of magnetic field and mixed convection parameter on velocity profile The velocity declines for the rising value of the magnetic field parameter, and this occurs because a magnetic field generates Lorentz force, which opposes motion and reduces it; hence, a stronger magnetic field results in a lower velocity, as shown in Fig. 2a. The velocity then rises again as bioconvective and buoyant forces become dominant, particularly away from the wall. As the mixed convection parameter increases, the velocity profile also rises. The basis for this phenomenon is that whenever buoyancy on free convection becomes significant, mixed convection happens. The buoyancy becomes increased as the mixed convection parameter value rises. Hence, the velocity of the flow increases. However, when buoyancy becomes too strong, it causes flow stratification and increased resistance; hence, velocity drops again as shown in 2b.Fig. 2Velocity profile for different values of the parameters: (a) Magnetic field and (b) mixed convection. Velocity profile for different values of the parameters: (a) Magnetic field and (b) mixed convection. Impact of thermophoresis and Brownian motion parameter on the temperature profile Fig. 3Temperature profile for different values of the parameters: (a) thermophoresis and (b) Brownian motion. Temperature profile for different values of the parameters: (a) thermophoresis and (b) Brownian motion. The Fig. 3a shows that the temperature profile consequently increases for the rising value of the thermophoresis parameter. This occurs as a result of the movement of smaller particles during the thermophoresis process from a hotter to a cooler region, or from a high-temperature segment to a lower-temperature portion. Consequently, heat transfers rapidly from the hotter surface to the fluid, boosting its temperature. Figure 3b displays that for the boosting values of the Brownian motion parameter, which describes the random movement of particles suspended in a fluid, the temperature profile increases. Impact of the buoyancy ratio parameter and the thermal radiation parameter on the temperature profile The heat accumulates near the hot boundary because it is not removed quickly. As the buoyancy ratio increases, the temperature penetrates further into the fluid region. Consequently, the temperature profile \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta (\eta )$$\end{document} in Fig. 4a increases, and the thickness of the thermal boundary layer also becomes larger. Figure 4b ensures that as the thermal radiation parameter’s values increase, the temperature profile rises. It’s well known that increasing the radiation parameter enhances the fluid’s capacity to carry energy, which accelerates the transmission of heat. Actually, as thermal radiation increases, the nanofluid’s temperature profiles rise because of the enhanced heat-absorption capabilities of nanoparticles and the increased energy transfer brought on by radiation. Several engineering applications, such as solar energy systems, prominently exhibit this phenomenon, where the use of nanofluids improves the efficiency of heat transmission.Fig. 4Temperature profile for various values of the parameters: (a) Buoyancy ratio and (b) thermal radiation. Temperature profile for various values of the parameters: (a) Buoyancy ratio and (b) thermal radiation. Impact of the magnetic field parameter on the temperature and concentration profile Figure 5a demonstrates that increasing the magnetic-field parameter raises the temperature profile because it creates a Lorentz force that resists fluid motion, reduces convective mixing, and requires the system to depend on weak conduction to remove heat. As the magnetic field parameter is increased, the fluid’s concentration increases because the Lorentz force rises, reducing the fluid velocity; hence, for the boosting value of the magnetic field parameter, the concentration profile increases as shown in Fig. 5b.Fig. 5Magnetic field parameter: (a) temperature and (b) concentration profiles for various values. Magnetic field parameter: (a) temperature and (b) concentration profiles for various values. Table 3 provides the heat transfer rate values for the following parameters: surface temperature, magnetic field, radiation, buoyancy ratioand thermophoresis parameter.Table 3Effects of different physical parameters on the rate of heat transfer -θ '(0).NtNbNrMRdq-θ '(0)0.20.20.10.50.50.10.194710.30.187200.40.180190.50.173650.20.181450.30.167030.40.151030.60.190360.70.186360.80.182660.20.206690.30.202380.40.198400.20.191900.30.189330.40.18734 Table 3Effects of different physical parameters on the rate of heat transfer -θ '(0).NtNbNrMRdq-θ '(0)0.20.20.10.50.50.10.194710.30.187200.40.180190.50.173650.20.181450.30.167030.40.151030.60.190360.70.186360.80.182660.20.206690.30.202380.40.198400.20.191900.30.189330.40.18734 Effects of different physical parameters on the rate of heat transfer -θ '(0). Fig. 6(a) Buoyancy ratio and (b) themophoresis parameter on concentration profile for various values. (a) Buoyancy ratio and (b) themophoresis parameter on concentration profile for various values. Impact of the buoyancy ratio parameter and the thermophoresis parameter on the concentration profile Raising the buoyancy ratio in bioconvection nanofluid flow enhances both chemical and biological buoyancy forces, boosts upward convective motion, thickens the nanoparticle boundary layer, and hence increases the concentration profile as shown in Fig. 6a. A strong repulsion force is produced by the intense heat near the wall. The nanoparticles are physically pushed out into the cooler surrounding fluid and kicked away from the heated surface. The particles migrate outward and build up within the fluid domain as a result of being aggressively pushed away from the wall. The nanoparticles enter the fluid more deeply as a result of this outward movement. Consequently, the nanoparticle concentration boundary layer thickens and swells, and the dimensionless concentration profile s(η ) rises in the Fig. 6b.Fig. 7Concentration profile: (a) variable viscosity parameter and (b) Lewis number . Concentration profile: (a) variable viscosity parameter and (b) Lewis number . Impact of the variable viscosity parameter and the Lewis number on the concentration profile An increase in the variable viscosity parameter signifies a reduction in the internal flow resistance and cohesive forces within the nanofluid. As the fluid becomes less viscous, it moves more freely, which accelerates the flow velocity. This faster-moving fluid creates a strong sweeping effect. Because the nanoparticles are swept away rather than being allowed to accumulate, the solutal (concentration) boundary layer becomes thinner. Consequently, the overall nanoparticle concentration profile decreases as shown in Fig. 7a. The mass diffusivity to heat diffusivity ratio is commonly referred to as the Lewis number. From Fig. 7b, it is clear that increasing the Lewis number leads the concentration profile to drop.Table 4Effects of different physical parameters on the rate of mass transfer -ϕ '(0).NtNrNvLe-ϕ '(0)0.20.1220.347660.30.327440.40.312970.50.302900.20.323460.30.297090.40.267661.50.325242.50.3594430.3667410.2063530.4603740.55395 Table 4Effects of different physical parameters on the rate of mass transfer -ϕ '(0).NtNrNvLe-ϕ '(0)0.20.1220.347660.30.327440.40.312970.50.302900.20.323460.30.297090.40.267661.50.325242.50.3594430.3667410.2063530.4603740.55395 Effects of different physical parameters on the rate of mass transfer -ϕ '(0). The mass transfer rates of thermophoresis parameter Nt, buoyancy ratio Nr, variable viscosity parameter Nv, and Lewis number Le are listed in Table 4. It is observed that the mass transfer rate drops with increasing Nt values and rises with increasing Le and Nb values. Impact of the bioconvection Lewis number and the Peclet number on the microbe density profile The ratio of the diffusivity of microbes and the thermal effective diffusion of porous media is known as the bioconvection Lewis number. Rising Lb values, as shown in Fig. 8a, indicate a decline in the diffusion of microorganisms, resulting in a decrease in bacteria. For the boosting values of the bioconvection Lewis number, the rate of viscous diffusion increases, causing the density profiles in the boundary layer to decline. The motile density function is less affected by microbes because their diffusivity decreases as the Peclet number increases; this relationship is illustrated in the Fig. 8b, where the Peclet number Pe and cell swimming speed W\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_c$$\end{document} are directly proportional to each other and inversely proportional to the diffusivity of microorganisms.Fig. 8Density profile of organisms: (a) bioconvection Lewis number and (b) Peclet number.Fig. 9Organism density profiles: (a) mixed convection parameter and (b) bioconvection Rayleigh number. Density profile of organisms: (a) bioconvection Lewis number and (b) Peclet number. Organism density profiles: (a) mixed convection parameter and (b) bioconvection Rayleigh number. Impact of mixed convection parameter and bioconvection Rayleigh number on organism density profile Figure 9a illustrates that the microorganism density profile is declined when the mixed convection parameter λ rises. The momentum equation has a mixed convection parameter, such as λ, which has a significant connection to the microbe density function. The microorganism density profile rises as shown in Fig. 9b for the increasing values of the bioconvection Rayleigh number (Rb). Table 5 illustrates how the rate of microbe density number increases when λ, Pe, and Lb increase as well.Table 5Effects of different physical parameters on the rate of microbes density -ζ '(0)).LbPeλRb- ζ’(0)20.51.20.50.5215930.6218840.7055050.778630.20.439590.30.466440.40.493771.30.542561.40.562761.50.582280.20.615100.30.585870.40.55484 Table 5Effects of different physical parameters on the rate of microbes density -ζ '(0)).LbPeλRb- ζ’(0)20.51.20.50.5215930.6218840.7055050.778630.20.439590.30.466440.40.493771.30.542561.40.562761.50.582280.20.615100.30.585870.40.55484 Effects of different physical parameters on the rate of microbes density -ζ '(0)). Statistical analysis Numerical computational simulations have a higher interpretation, which makes an experimental scheme essential. Utilizing computer programming, data collection is created and then applied to actual situations. The Response Surface Methodology (RSM) is a technique also known as the surface regression model that takes into account the possibility that several input factors may influence response and uses experimental design to determine the significant input parameter and the precise quantity of an input parameter that can improve response. The general quadratic model42 explains how the input variables and the output response are related. The quadratic model also has three linear terms, three bilinear terms with two components, and one intercept term. The most well-known experiment for fitting the second-order model is the ”Central Composite Design” (CCD). Surface regerssion model The process began by constructing a Central Composite Design matrix to define the specific boundary combinations of the selected independent operational parameters. For each distinct design point, the governing coupled differential equations of the bioconvective nanofluid were solved numerically to obtain the exact output responses, namely the Nusselt number, Sherwood number, and local microorganism density. These numerical outputs were then utilized to fit second-order polynomial equations via the Method of Ordinary Least Squares (OLS), calculating the precise empirical weights for the linear, quadratic, and interaction effects. Finally, Analysis of Variance (ANOVA) was executed to statistically validate the adequacy of the fitted equations, ensuring that the resulting 3D response surface plots reliably and accurately map the physical behavior of the fluid system. The formula \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$2^3$$\end{document} [factorial point] + 2*3 [axial point] + 6 [central point] = 20 is utilized. To calculate the number of experiments required for these variables, 20 runs with three variables were insisted on in this experiment. Typically, the second-order model is represented as29\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} y= a_{0}+ \sum _{i=1}^{k}a_{i}x_{i}+ \sum _{i=1}^{k}a_{ii} x_{i}^{2}+\sum \sum _{i=j}a_{ij} x_{i} x_{j} + \varepsilon \end{aligned}$$\end{document} Model accuracy for Nu\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} The heat transfer rate is influenced by Rd, q, and Nt parameters. Thus, for various response parameters, Table 6 illustrates the selective input parameters along with their levels.Table 6Parameter range analysis for heat transfer rate.ParameterLevelLowMediumHighRd0.30.40.5q0.10.20.3Nt0.20.30.4 Table 6Parameter range analysis for heat transfer rate.ParameterLevelLowMediumHighRd0.30.40.5q0.10.20.3Nt0.20.30.4 Parameter range analysis for heat transfer rate. Fig. 10(a) Residual Plot, (b) Histogram and (c) Q-Q Plot for heat transfer rate. Fig. 11Anova table for heat transfer rate. Fig. 12Summary statistics for heat transfer rate. (a) Residual Plot, (b) Histogram and (c) Q-Q Plot for heat transfer rate. Anova table for heat transfer rate. Summary statistics for heat transfer rate. The normal probability plot drawn for Nu\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} is shown in Fig. 10. Figure 11 displays the results of the ANOVA analysis for various responses and independent variables. The variance of the various components of the model is measured by the sum of squares and adjusted mean squares. The components are statistically prominent, as evidenced by the large F-value and low P-value (less than 0.05). Also noted that all terms are significant from Fig. 12. Sensitivity analysis for Nu\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} The heat transfer rate quadratic model is given as follows.30\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \begin{aligned} Nu_{x} = -0.237533 + 0.052939Rd + 0.011750q +0.108882Nt + 0.043500Rdq \\ - 0.038500RdNt-0.017250qNt -0.013636Rd^{2} -0.008636q^{2} - 0.026136Nt^{2}\\ \end{aligned} \end{aligned}$$\end{document}The sensitivity analysis has been calculated by taking partial derivatives with the involved variables, and the sensitivity functions for the Nusselt number become31\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial Nu_{x}}{\partial Rd} = 0.052939+0,043500q-0.038500Nt-0.027272Rd \end{aligned}$$\end{document}32\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial Nu_{x}}{\partial q} = 0.011750 +0.043500Rd-0.017250Nt-0.017272q \end{aligned}$$\end{document}33\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial Nu_{x}}{\partial Nt} = 0.10882-0.038500Rd-0.017250q-0.052272Nt \end{aligned}$$\end{document}In Table 7, the sensitivity analysis are shown in three levels, which are graphically shown in Fig. 13.Fig. 13Sensitivity analysis for Nu\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document}: Rd=0.3, (a) q=0.1, (b) q=0.2, (c) q=0.3, Nt = 0.2, 0.3 and 0.4.Fig. 14(a) Residual Plot, (b) Histogram and (c) Q-Q Plot for mass transfer rate.Table 7Sensitivity analysis of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Nu_x$$\end{document} for Rd=0.3.qNtSensitivity\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Nu_x/\partial Rd$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Nu_x/\partial q$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Nu_x/\partial Nt$$\end{document}0.10.20.04145840.01962280.08509060.30.03755740.01789780.07986340.40.03370740.01617280.07463620.20.20.04575740.01789560.08336560.30.04190740.01617060.07813840.40.03805740.01444560.07291120.30.20.05010740.01616840.07813840.30.04625740.01444340.07641340.40.04240740.01271840.0746884 Sensitivity analysis for Nu\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document}: Rd=0.3, (a) q=0.1, (b) q=0.2, (c) q=0.3, Nt = 0.2, 0.3 and 0.4. (a) Residual Plot, (b) Histogram and (c) Q-Q Plot for mass transfer rate. Table 7Sensitivity analysis of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Nu_x$$\end{document} for Rd=0.3.qNtSensitivity\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Nu_x/\partial Rd$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Nu_x/\partial q$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Nu_x/\partial Nt$$\end{document}0.10.20.04145840.01962280.08509060.30.03755740.01789780.07986340.40.03370740.01617280.07463620.20.20.04575740.01789560.08336560.30.04190740.01617060.07813840.40.03805740.01444560.07291120.30.20.05010740.01616840.07813840.30.04625740.01444340.07641340.40.04240740.01271840.0746884 Sensitivity analysis of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Nu_x$$\end{document} for Rd=0.3. A vertical bar chart has been created using the sensitivity analysis results43. In Fig. 13, the sensitivity value of an upward bar is positive. The sensitivity of Nu\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Rd and q is always positive. For all values of Nt, the positive approach of Rd and q is seen in three levels. As per the physics of the problem, the heat transfer rate depends upon the parameters Rd, q, and Nt, which are justified by the governing Eq. (16). Similarly, the mass transfer rate depends upon Le, Nv, and Nt by Eq. (17), and the microbe density rate depends upon Pe, Lb, and Rb by Eq. (18). Model accuracy for Sh\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} Table 8 demonstrates the selective input parameters Le, Nv, and Nt with their levels for different response parameters.Table 8Parameter range analysis for mass transfer rate.ParameterLevelLowMediumHighLe123Nv1.522.5Nt0.20.30.4 Table 8Parameter range analysis for mass transfer rate.ParameterLevelLowMediumHighLe123Nv1.522.5Nt0.20.30.4 Parameter range analysis for mass transfer rate. Figure 14 displays the normal probability plot for Sh\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document}. The ANOVA analysis for different responses to different independent variables has been recorded in the Fig. 15. The variation of the various terms in the model is determined by the sum of squares and adjusted mean squares. Model validation on a response is determined by the F- and P-values. The variables in the model are statistically significant, as evidenced by the large F-value and low P-value. From Fig. 16, it is noted that all the quadratic terms are significant.Fig. 15Anova table for mass transfer rate.Fig. 16Summary statistics for mass transfer rate. Anova table for mass transfer rate. Summary statistics for mass transfer rate. Sensitivity analysis for Sh\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} The following is the quadratic model for the mass transfer rate.34\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \begin{aligned} Sh_x = -0.13096Le-0.06687Nv+0.025545Nt-0.02054LeNv\\ -0.02859LeNt+0.068888NvNt+0.01321Le^2+0.01589Nv^2\\ \end{aligned} \end{aligned}$$\end{document}The sensitivity analysis has been derived by taking partial derivatives with respect to the involved variables, resulting in the sensitivity functions for the mass transfer rate.Fig. 17Sensitivity analysis for Sh\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document}: Le = 1, (a) Nv=1.5, (b) Nv=2, (c) Nv=2.5 Nt = 0.2, 0.3 and 0.4.35\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial Sh_{x}}{\partial Le} = -0.13096-0.02054Nv-0.02859Nt+0.02642Le \end{aligned}$$\end{document}36\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial Sh_{x}}{\partial Nv} = -0.06687-0.02054Le-0.06888Nt+0.03178Nv \end{aligned}$$\end{document}37\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial Sh_{x}}{\partial Nt} = 0.25545-0.02859Le-0.068888Nv \end{aligned}$$\end{document}Table 9Sensitivity analysis of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Sh_x$$\end{document} for Le = 1.NvNt\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Sh_x / \partial Le$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Sh_x / \partial Nv$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Sh_x / \partial Nt$$\end{document}1.50.2− 0.141068− 0.0535160.123540.3− 0.1439270.0604040.123540.4− 0.1467860.0672920.1235420.2− 0.1513380.0740560.08910.3− 0.1541970.0809440.08910.4− 0.1570560.0878320.08912.50.2− 0.06974910.0843260.054660.3− 0.06973230.0912140.054660.4− 0.06971550.0981020.05466 Sensitivity analysis for Sh\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document}: Le = 1, (a) Nv=1.5, (b) Nv=2, (c) Nv=2.5 Nt = 0.2, 0.3 and 0.4. Table 9Sensitivity analysis of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Sh_x$$\end{document} for Le = 1.NvNt\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Sh_x / \partial Le$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Sh_x / \partial Nv$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial Sh_x / \partial Nt$$\end{document}1.50.2− 0.141068− 0.0535160.123540.3− 0.1439270.0604040.123540.4− 0.1467860.0672920.1235420.2− 0.1513380.0740560.08910.3− 0.1541970.0809440.08910.4− 0.1570560.0878320.08912.50.2− 0.06974910.0843260.054660.3− 0.06973230.0912140.054660.4− 0.06971550.0981020.05466 Sensitivity analysis of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Sh_x$$\end{document} for Le = 1. In Table 9, the sensitivity analyses are shown in three levels and graphically represented in Fig. 17. The sensitivities of the local Sherwood number Sh\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Nt are positive, and Le and Nv are negative, and this approach of Nt and Nv appears for Le = 1 and for all values of Nt in three levels.Fig. 18(a) Residual Plot, (b) Histogram and (c) Q-Q Plot for microbes density rate.Fig. 19Anova table for microbes density rate.Fig. 20Summary statistics microbes density rate. (a) Residual Plot, (b) Histogram and (c) Q-Q Plot for microbes density rate. Anova table for microbes density rate. Summary statistics microbes density rate. Model accuracy for Dm\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} The microorganism density rates are influenced by the parameters such as Pe, Lb, and Rb. Table 10 demonstrates the selective input variables with their levels for different responses.Table 10Parameter range analysis for microbes density rate.ParameterLevelLowMediumHighPe0.30.40.5Lb234Rb0.30.40.5 Table 10Parameter range analysis for microbes density rate.ParameterLevelLowMediumHighPe0.30.40.5Lb234Rb0.30.40.5 Parameter range analysis for microbes density rate. Figure 18 displays the normal probability plot for Dm\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document}. The ANOVA analysis results for each of the independent variables are shown in Fig. 19. Each component of the model uses adjusted mean squares and sum of squares to represent its variance. Furthermore, the high F-value and low P-value suggest that the parameters are statistically prominent. From Fig. 20, it is noted that all terms are significant.Table 11Sensitivity analysis of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Dm{_x}$$\end{document} for Pe = 0.3.LbRb\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial D{m _x} / \partial Pe$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial D{m_x} / \partial Lb$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial D{m_x} / \partial Rb$$\end{document}20.2−0.24295− 0.10736550.22128550.3− 0.2387935− 0.10396420.24108550.4− 0.234631− 0.10056290.260885530.2− 0.240393− 0.09155550.25529850.3− 0.2362305− 0.08815420.27509850.4− 0.232068− 0.08475290.294898540.2− 0.23783− 0.07574550.28931150.3− 0.2336675− 0.07234420.30911150.4− 0.229505− 0.06894290.3289115 Table 11Sensitivity analysis of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Dm{_x}$$\end{document} for Pe = 0.3.LbRb\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial D{m _x} / \partial Pe$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial D{m_x} / \partial Lb$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\partial D{m_x} / \partial Rb$$\end{document}20.2−0.24295− 0.10736550.22128550.3− 0.2387935− 0.10396420.24108550.4− 0.234631− 0.10056290.260885530.2− 0.240393− 0.09155550.25529850.3− 0.2362305− 0.08815420.27509850.4− 0.232068− 0.08475290.294898540.2− 0.23783− 0.07574550.28931150.3− 0.2336675− 0.07234420.30911150.4− 0.229505− 0.06894290.3289115 Sensitivity analysis of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Dm{_x}$$\end{document} for Pe = 0.3. Fig. 21Sensitivity analysis for Dm\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document}: Pe = 0.3, (a) Lb=2, (b) Lb=3, (c) Lb=4 and Rb = 0.2, 0.3 and 0.4. Sensitivity analysis for Dm\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document}: Pe = 0.3, (a) Lb=2, (b) Lb=3, (c) Lb=4 and Rb = 0.2, 0.3 and 0.4. Sensitivity analysis for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Dm_x$$\end{document} The following is the quadratic model for the organism density rate.38\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} Dm_x &= -0.202258 -0.256407Pe - 0.146557Lb + 0.101172Rb + 0.002563PeLb \\ &\quad+0.041625PeRb + 0.0034013LbRb + 0.007905Lb^2 + 0.099000 Rb^2\\ \end{aligned}$$\end{document}The sensitivity analysis involves analyzing the partial derivatives of the key variables, resulting in the sensitivity functions for organism density number.39\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial Dm_{x}}{\partial Pe} = -0.256407 + 0.002563Lb + 0.041625 \end{aligned}$$\end{document}40\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial Dm_{x}}{\partial Lb} = -0.146557 + 0.002563Pe +0.034013Rb + 0.01581 Lb \end{aligned}$$\end{document}41\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \frac{\partial Dm_{x}}{\partial Rb} = 0.101172 + 0.041625Pe +0.034013Lb +0.198000Rb \end{aligned}$$\end{document}The sensitivity analysis for all three levels given in Table 11 and Fig. 21 displays the graphical representation. The sensitivities of Dm\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Pe and Lb are negative, and Rb is positive. Thus, the negative sensitivity of motile microorganisms Dm\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Pe decreases for all values of Rb in three levels. Conclusions The impacts of significant parameters are represented graphically, and the obtained results are explained in detail with suitable physical interpretations. Furthermore, a brief conclusion follows from the sensitivity analysis of heat transfer rate, mass transfer rate, and microbe density rate to the significant parameters. Summarized results of the current work:As the magnetic field parameter value rises, the velocity profile declines.For the boosting value of the magnetic field parameter, the Brownian motion parameter, the thermal radiation parameter, and the thermophoresis parameter, the temperature profile increases.The concentration profile declines when the variable viscosity parameter and the Lewis number increase and rises for the magnetic field.The microbe density reduces for the bioconvection Lewis number, the bioconvection Peclet number, and the mixed convection number, whereas it increases for the bioconvection Rayleigh number.The sensitivity of Nu\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Rd, q, and Nt is positive. For all values of Nt, the positive approaches of Rd and q are seen in three levels.The sensitivities of the local Sherwood number Sh\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Nt are positive and negative for Le and Nv.The sensitivities of microbes Dm\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Pe and Lb are negative and positive for Rb.In conclusion, there are numerous opportunities to enhance the transfer of heat, energy production, environmental management, and even healthcare through the implementation of bioconvection in nanofluid flows. Exciting prospects arise from the integration of nanotechnology with biological systems, but there are also technical challenges that require further study. As the magnetic field parameter value rises, the velocity profile declines. As the magnetic field parameter value rises, the velocity profile declines. For the boosting value of the magnetic field parameter, the Brownian motion parameter, the thermal radiation parameter, and the thermophoresis parameter, the temperature profile increases. For the boosting value of the magnetic field parameter, the Brownian motion parameter, the thermal radiation parameter, and the thermophoresis parameter, the temperature profile increases. The concentration profile declines when the variable viscosity parameter and the Lewis number increase and rises for the magnetic field. The concentration profile declines when the variable viscosity parameter and the Lewis number increase and rises for the magnetic field. The microbe density reduces for the bioconvection Lewis number, the bioconvection Peclet number, and the mixed convection number, whereas it increases for the bioconvection Rayleigh number. The microbe density reduces for the bioconvection Lewis number, the bioconvection Peclet number, and the mixed convection number, whereas it increases for the bioconvection Rayleigh number. The sensitivity of Nu\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Rd, q, and Nt is positive. For all values of Nt, the positive approaches of Rd and q are seen in three levels. The sensitivity of Nu\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Rd, q, and Nt is positive. For all values of Nt, the positive approaches of Rd and q are seen in three levels. The sensitivities of the local Sherwood number Sh\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Nt are positive and negative for Le and Nv. The sensitivities of the local Sherwood number Sh\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Nt are positive and negative for Le and Nv. The sensitivities of microbes Dm\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Pe and Lb are negative and positive for Rb. The sensitivities of microbes Dm\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$_x$$\end{document} to Pe and Lb are negative and positive for Rb. This study gives engineers exact, data-driven parameters to optimize thermal efficiency while preventing nanoparticle agglomeration by utilizing a surface regression model for a bioconvective nanofluid model. The design of complex thermal management systems, such as microbial fuel cells and smart bio-nanocoolants, will benefit greatly from these findings. To further improve thermal conductivity, future research should investigate the incorporation of hybrid nanofluids, which suspend several different nanoparticles, building on this fundamental framework. The present study acts as a bridge due to statistical optimization (response surface methodology, also known as the surface regression model); this statistic is used to find the absolute best operational numbers and limits. Also, it equips thermal engineers with the predictive tools necessary to optimize and build advanced, high-performance industrial systems, such as those used in energy-efficient manufacturing processes and sustainable building designs.