Assessment of construction waste aggregates as a road raw material using response surface methods Authors: Vishal Dhiman, Swasti Sharma, Preetha Ravisree, Shivangi Sharma Published: 2026 ABSTRACT AbstractThe rapid expansion of the road network in India over the last decade has generated a significant quantity of concrete waste aggregates (CWAs), leading to serious disposal and environmental concerns. Limited efforts toward developing innovative reuse technologies have accelerated the dumping of CWAs in landfill sites and water bodies. In this study, the feasibility of utilizing bitumen emulsion pre-treated CWAs in asphalt wearing course (WC) construction was investigated to promote sustainable pavement development. Response Surface Methodology (RSM) was employed as an optimization approach to evaluate the influence of key experimental variables, including bitumen content (VG30), percentage of pre-treated CWAs, and temperature, on the performance characteristics of asphalt mixtures. Marshall Stability, moisture resistance, stiffness, and volumetric properties were experimentally analysed and compared with MoRTH specifications. The results demonstrated that bitumen emulsion treatment significantly improved the engineering performance and durability characteristics of CWAs-based asphalt mixtures. Under optimized conditions of bitumen content = 4.79%, pre-treated CWAs = 21.02%, and temperature = 9.9 °C, all response parameters were found to satisfy the permissible limits for WC construction materials. The study highlights the novelty of integrating CWAs, bitumen emulsion treatment, and RSM optimization for sustainable pavement applications. Overall, the findings confirm that treated CWAs can be effectively reused in road construction in India, thereby reducing environmental impacts associated with waste disposal and encouraging the development of sustainable construction practices and policies.Keywords: Box Behnken approach (BBD), Waste management, sustainable development, concrete waste aggregates, central composite design (CCD), response surface methodology (RSM).Subject terms: Engineering, Environmental sciences, Materials science Introduction Though, processes involved under the infrastructure development viz., construction, demolishing, repair etc., cause several issues such as, air pollution, water pollution, noise pollution and generation of the concrete waste aggregates (CWAs). Among these issues, the latter-most i.e., generation of the CWAs has several indirect or direct impacts on the atmosphere1,2. Because of the difficult climate and lack of resources, CWA management has not been successful in hilly locations3. The novelty of the study lies in the integrated approach of utilizing bitumen emulsion pre-treated concrete waste aggregates (CWAs) for asphalt wearing course applications, particularly under low-temperature conditions. Unlike conventional studies that directly use untreated recycled aggregates, this research introduces a specific pre-treatment mechanism using bitumen emulsion to enhance the surface characteristics, adhesion properties, and moisture resistance of CWAs before their incorporation into asphalt mixtures. Furthermore, the study systematically evaluates the combined influence of bitumen content, treated CWA percentage, and temperature through Response Surface Methodology (RSM)-based optimization4. A significant novelty is the demonstrated improvement in Marshall Stability, stiffness, moisture susceptibility resistance, and volumetric performance, with all optimized results satisfying MoRTH requirements5. The research also highlights the suitability of treated CWAs for cold-region or low-temperature pavement applications, thereby contributing to sustainable and durable road infrastructure development. The main infrastructural development in these areas is the construction and maintenance of roads6. Roads constructed in hilly regions are sometimes continuously damaged by unprecedented events such as earthquakes, landslides, heavy rains, and the falling of big rocks and boulders. Because of this, roads in these areas require regular maintenance, which results in a large number of CWAs. Usually, the CWAs generated in this way are dumped into nearby bodies of water, collected off the side of the road, or dumped in landfills7. The way of life of those downstream may eventually be disrupted by these CWA management strategies, which may also lead to other significant issues including traffic jams, changes in river flow, and impacts on local wildlife and flora8.Their lifespan is shortened since the CWAs occupy territory meant for dumping municipal solid waste9. The effect of quarry dust-based geopolymer cement on the compressive strength, erodibility, and durability potential of expansive soils has been studied under laboratory conditions. The particular interest was on the geopolymer cement treatment of soils subgrade under hydraulically bound environments10. Taking into account a number of environmental impacts related to CWA management and the global need to fulfil the Sustainable Development Goals (SDGs) of the United Nations, specifically SDGs Good Health and Well-Being, Decent Work and Economic Growth, Responsible Consumption and Production, and Climate Action11. Pavement structures often are under tension and compression mobilised by the coupled effects of traffic loads and swelling stress. Seasonal moisture variations cause capillarity rise and volumetric movement within the subgrade12. Recycling and reusing them as building materials is one of the potential approaches to manage CWAs that has gained popularity among civil engineers13. Earlier studies proved the use of CWAs in the construction as per requirement of the base and sub-base layers of pavements as per IRC14. Nevertheless, building materials manufactured with CWAs exhibit deteriorated quality in their characteristics, such as reduced resistance to permanent deformation and low water resistance15. As a result, the use of CWAs as a building material is acceptable to civil engineers. To increase the CWAs’ reusability, the scientists are working on a number of projects, including pre-treating them with certain chemicals and optimizing their percentage16. According to reports, the CWAs were pre-treated using a variety of techniques, including heat, cement paste, liquid silicon resin, etc.17. Nano-geopolymer binders (NGB) of 5%, 10%, 15%, and 20% concentration were used to stabilize expansive subgrade soil against strain deformation, as well as to improve its durability18. The effect of quarry dust-based geopolymer cement on the compressive strength, erodibility, and durability potential of expansive soils has been studied under laboratory conditions. The particular interest was on the geopolymer cement treatment of soils subgrade under hydraulically bound environments. Lateritic soils, which form the compacted foundation of pavements, tend to swell upon contact with moisture and shrink during the drying periods19. The purpose of this study was to examine the utility of the CWAs produced from destroyed roads in India’s Himachal Pradesh region. Excessive swelling and high compressibility of soil have posed countless challenges such as poor dynamic shear strength for engineers dealing with cyclic loading in pavement structure20. The failure of the preloading pressure and NGB application to sustain cyclic stress in subgrade was due to the high brittleness characterized by the nano-geopolymer-treated subgrade21. To address this challenge, the durability and mechanical properties of the investigated subgrade were treated with 10%, 20%, and 30% of activated nano-disilicate fly ash (NDFA) to the dry mass of the subgrade soil22. Utilizing CWAs as a component of aggregate in the production of wearing coats (WC) is the main objective of this work23. In order to achieve the appropriate volumetric and mechanical properties—which are necessary for the building of WC—the CWAs also underwent treatment with bitumen emulsion24. Additionally, bitumen binder, temperature, and CWA concentration were optimized using RSM in conjunction with CCD and BBD. As far as we are aware, there aren’t many of these studies, but their conclusions could inspire the global auditory. Methodology Raw materials Aggregates as per IRC Concrete waste aggregates (CWAs) were first collected, cleaned, crushed, and sieved according to the required gradation for asphalt wearing course mixtures. The processed CWAs were then pre-treated using bitumen emulsion to improve surface bonding characteristics and reduce moisture susceptibility before mixing with virgin aggregates. Asphalt specimens were prepared using the Marshall Mix Design method with varying proportions of bitumen content, pre-treated CWAs, and controlled temperature conditions25. The experimental program evaluated key performance parameters, including Marshall Stability, flow value, stiffness, volumetric properties, and moisture resistance, in accordance with relevant MoRTH and ASTM standards. Testing conditions were carefully controlled to assess the behaviour of the mixtures under low-temperature conditions relevant to pavement applications. Response Surface Methodology (RSM) was employed to optimize the experimental variables and analyse their combined effects on asphalt mixture performance. The optimized mixture conditions were identified based on compliance with permissible specification limits and overall mechanical performance26. In the current study, CWAs remained utilized as aggregates. The main collection sites of CWAs were at the Indian highway construction and repair site between Manali and Chandigarh NH21. Figure 1: Illustrates the geographical location and construction details of the selected road repair site used for the collection of construction waste aggregates (CWAs) for the present investigation. depicts the location of the construction site. The main location of construction site is situated at an elevation of 3450 feet above main sea level (MSL). Twenty kilogram of CWA’s were gathered and brought to the lab. Petrous materials and concrete comprised the vast majority of the total CWAs (91.2%). The remaining 8.8% of the composition was made up of impurities or undesirable materials like gypsum, rubber, or wood. Before being used for analysis in laboratories, contaminants were manually eliminated from CWAs since they can lead to differences in Marshall-based testing and other testing27. SEM/EDS was used to further analyse both kinds of aggregates. The results of this research showed that the siliceous content of CWAs and hornfels was 61% and 63%, respectively. This also illustrated the aggregates’ incapacity to withstand water-induced degradation. Additionally, the morphological characteristics of the two types of aggregates were examined. The aggregates’ morphological characteristics are described in Table 1 according to the standard testing protocol (as specified by IS codes) and MoRTH criteria28. Table 1Characteristics of Aggregates Based on Traditional Techniques.Property (Standard)UnitsNatural AggregatesCDW AggregatesTreated CDW aggregatesMethod of TestRequirements (MoRTH 5th Revision / IS: 2386)Crushing ValueIn Percentage16.2539.2332.33IS: 2386 Part 4Max 30% as per MoRTH / (Max 45% as per IS:2386 Part 4)Los Angeles AbrasionIn Percentage24.6643.1038.22IS: 2386Max 35%Aggregate ImpactIn Percentage22.4434.3431.55IS: 2386Max 27%Specific gravity-2.663.663.26IS: 2386 Part 32.5–3Water absorptionIn Percentage1.652.652.25IS: 2386 Part 3Max 2%Coating and stripping of bitumen aggregate mixIn Percentage1019193IS: 6241Minimum retained coating 95%Angularity Number-8.6612.2211.2IS: 2386 Part 17–10 Characteristics of Aggregates Based on Traditional Techniques. Table 1 shows that nearly all of the morphological attributes’ necessary limits are not met by the CWAs. Usually, porous mortar is used to cover the CWAs, improving their specific gravity, water absorption, angularity and crushing properties29. So, the CWAs and hornfels must be blended in order to achieve the required properties. By calculating the Los Angeles abrasion of the CWA and hornfels mixture, as illustrated in Fig. 2, the quantity of CWAs that might be utilized in place of the hornfels was ascertained30. Calculating the greatest amount that the CWAs may replace the hornfels. Figure 2 suggests that in order to meet IS: 2386 Part 5 standard limits, a maximum of 52.4% of the hornfels could be replaced with CWAs. CWAs may lead to high consumption of bitumen because of the absorptive nature of the CWAs31. Therefore, in present investigations, maximum 40% of the hornfels were replaced with the CWAs. Other constituents The fine aggregates were those that were retained on a 75-micron filter after passing through a 2.36-millimeter sieve. The small aggregates utilized in the study were dust-free, rigid, long-lasting, dry, and devoid of organic or other harmful materials32. Filler was made from the leftover material after the fine aggregates were separated. Both the filler and the tiny aggregates underwent laboratory testing. Table 2 provides an explanation of the analysis’s findings. Table 2Results of laboratory tests on filler (stone dust) and fine aggregates.MaterialsTestTest ValueRequirements (MoRTH 5th Revision)Method of TestFine aggregateSand Equivalent60≥ 50IS: 2720 (Part 37), AASHTO T176Specific Gravity2.53IS: 2386 Part IIIFillerPlasticity Index3.5≥ 4IS: 2720 (Part 5)Specific Gravity2.45IS: 2386 Part III Results of laboratory tests on filler (stone dust) and fine aggregates. Table here shows that the fine aggregate met IS: 2720 (Part 37) or AASHTO T176 requirements because it had a sand equivalency value of at least 50. When tested in accordance with IS: 2720 (Part 5) (IS: 2770 (PART XXXVII) − 1976), the filler used in this investigation had a plasticity index of no more than 4 and was free of organic contaminants33. The VG30 was utilized as a binder. Various laboratory experiment were evaluated VG30’s suitability as a binder. A summary of the studies were performed on VG30 binder and results is in below Table 334. Table 3Properties of bitumen (VG-30).PropertyTest MethodTest ResultsRequirements as per IS 73:2013 for VG 30Penetration 25 °C ,100 g, 5 s, 0.1 mmIS 1203–197851Min 45Softening point (R & B), °CIS 1205–197847.6Min 47Ductility Test, 25 °C, cmIS 1208–1978102.1Min 75 Properties of bitumen (VG-30). The VG30 binder grade satisfies all IS73:2013 standards for usage as a binder in our result. In the current study 4, 5, and 6% of VG30 binder were utilized as binder when creating WC trials in the lab. Additionally, bitumen, which contains 61% bitumen, was utilized to treat the CWAs’ surface prior to the mixing procedure35. Laboratory testing Preparing the specimen for optimization process By evaluating effects of procedure variables on response parameters, the process was optimized, utilizing the CWAs as aggregate in the creation of WC. The process factors chosen for this study were the bitumen-binder percentage of the material, temperature (which was considered for calculating stiffness), and the proportion of treatment and untreated CWAs36. Three kinds of the procedure’s parameters—the three parameters as low, medium, and high—were selected, as indicated in Table below37. The three X1–4 levels, as indicated in Table 4, were chosen based on the results of earlier scientific research and accepted norms. Since it is simpler to complete this work by hand, a coarse portion of the mixture was used in place of the CWAs. It was made sure that emulsion breaking had started before starting the process of mixing for WC. In the lab, cylindrical specimens measuring 105 millimetres in diameter and 65 millimetres in total height were created38. These specimens underwent additional testing for a number of parameters, including stiffness and volumetric properties like VMA, VFB, TSR, VA and FLOW VALUE. This manuscript refers to these tests as response parameters. To analyse the reaction parameters, a number of laboratory tests were conducted. Table 4Low medium and high levels used during statistical analysis.S. No.Process ParametersSymbolic representationUnit-1 (Low)0 (Medium)+ 1 (High)1Proportion of Treated CWAsX1%1025402Bitumen (VG 30) contentX2%4563TemperatureX3°C010204Proportion of Untreated CWAsX4%102540 Low medium and high levels used during statistical analysis. Absorption and water resistance parameters Evaluated by measuring the specimen’s stripping potential. To evaluate the TSR and stripping potential was considered by assessing the WC specimen’s decline in indirect tensile strength following contact with moisture. A total of ten cylindrical Marshal specimens were created, with an equal number of dry and wet forms39. The dried material was kept unaltered around a room temperature for a total of three days before to the final examination. However, the wet sample was kept in a bath of water at 40 °C and immersed in water for the following three days. After both kinds were left undisturbed for three days, each specimen’s tensile strength was evaluated40. Where, TSR depicts the tensile strength ratio (%); ITSw and ITSD show the tensile strength of the wet and dry specimen. For TSR of the WC specimen ≥ 80% is considered to be appropriate, as per specification of ASTM D 4867. Stiffness test The effect of the already treated CWAs on the specimen’s stiffness was assessed in relation to temperature41. In this case, an indirect tensile stiffness test was performed on the Marshall Strength Testing Machine specimen. For this test, five conditioning sine pulses were applied to the cylindrical Marshall Specimen, followed by sine test pulses42. The latter were assigned to the vertical diameter of the specimen. The load on the specimen was raised until 0.005% of the horizontal strain was produced. Following Eq. (2), the results of this analysis were then utilized to determine the specimen’s resilient modulus (RM) at various temperatures, namely 0, 10, and 20. In this case, MR stands for resilient modulus, F for load repetitions, z for horizontal recoverable deformation (mm), h for specimen thickness, and v for Poisson’s ratio. The value of v was taken to be 0.2843, as the scientific literature supports. Furthermore, it should be mentioned that MoRTH 2000 contains no clauses pertaining to MR specification44. Therefore, the specimen obtained with untreated CWAs, which is referred to as the controlled specimen in this publication, also underwent similar examination in order to compare the results. Statistical analysis Instead of using the time-consuming and labour-intensive One-Variable-At-a-Time (OVAT) method, a multivariate statistical method was used to establish a link between process variables and response parameters. The CCD and BBD approaches were used with RSM to construct the experiments and develop models that utilized either a linear or quadratic connection between the procedure parameters and response parameters. This strategy created a link between the reaction and process parameters that can be described using Eq. (3). The response function coefficients, Cn, X1 through X4, and Y, which represent response parameter(s), were calculated using the coefficient of regression software Stat-Ease Designs Expert (version 8.0.7.1)45. The accuracy of the models created using this application was then evaluated using analysis of variance (ANOVA). Other metrics calculated for the sufficiency assessment were goodness of fit, adjusted regression coefficients, and correlation regression coefficients. After thorough statistical analysis, 3D representations of the data were also produced using RSM. These graphs were used to evaluate the optimal circumstances46. Results and discussion Statistical data Quadratic and linear models that illustrated the relationship between response and process factors were developed based on the experimental findings. Equation (4) through (11) describe these quadratic and linear models. The response parameters, namely VMA, VA, VFB, MS, FLOW VALUE, TSR, RM (of treated CWAs), and RM (of untreated CWAs), are denoted by Y1 through Y8. Of these reaction parameters, Y1 through Y6 show the specimen’s volumetric properties, whereas Y7 through Y8 show the specimen’s stiffness. Additionally, Tables 5 and 6 explain the outcomes of the laboratory trials and compare them to the outcomes that were predicted using the models47. Table 5Comparison of laboratory and expected responses for volumetric characteristics and water resistance.S. No.CWAs (X1)BC (VG30) % (X2)VMA % (Y1)VA % (Y2)VFB % (Y3)MS kN (Y4)Flow Value (mm) (Y5)TSR % (Y6)VMA % (Y1)VA % (Y2)VFB % (Y3)MS kN (Y4)Flow Value (mm) (Y5)TSR % (Y6)140615.584.183312.992.3115.404.6281.4426.352.7889.652253.5814.783.976161.980.6215.224.4974.7617.962.2785.193256.4115.833.177212.689.1615.373.7881.9826.472.7391.96440416.384.874212.78815.585.1376.3420.732.4684.87525514.434.780242.69014.434.1478.3822.232.5088.59610414.324.375202.28914.303.4077.8717.712.2289.92725514.434.780242.69014.434.1478.3822.232.5088.59846.21514.774.977192.481.8315.465.1879.1024.362.6786.71925514.434.780242.69014.434.1478.3822.232.5088.591025514.434.780242.69014.434.1478.3822.232.5088.59113.78515.111.172142.589.0614.383.0977.6620.092.3390.481225514.434.780242.69014.434.1478.3822.232.5088.591310614.114.185272.391.7514.933.1580.4223.732.5492.32 Comparison of laboratory and expected responses for volumetric characteristics and water resistance. Table 6A comparison of laboratory and predicted stiffness responses.S. No.TREATED CWAs (X1)BC (VG30) % (X2)TEMP °C (X3)UNTREATED CWAs (X4)RESILIENT MODULUS (TREATED) MPa (Exp)RESILIENT MODULUS (UNTREATED) MPa (Exp)RESILIENT MODULUS (TREATED) MPa (Pred)RESILIENT MODULUS (UNTREATED) MPa (Pred)1255102511,10011,85511,10011,85522562025550548064539.754815.831052010529724,17122514.821684.8425602521,08020,40221595.520695.55255102511,10011,85511,10011,855640520404850425147014812.377106101011,40012,84812,10612715.68104101013,84113,62513176.713892.99255102511,10011,85511,10011,8551025420255644562264994928.2511406104010,83013,52611,49413,2581240504020,25120,07020,47220,4441310501022,25022,94522,33922383.614404104012,17011,95511463.811387.415255102511,10011,85511,10011,85516255102511,10011,85511,10011,855 A comparison of laboratory and predicted stiffness responses. Tables 5 and 6 demonstrate that there was no significant difference between the experimental and model-predicted results. For each of the following response parameters: RM (of treated CWAs), RM (of untreated CWAs), MS, FLOW VALUE, TSR, VMA, VA, VFB, and the corresponding regression coefficient (R2) is 0.81, 0.73, 0.81, 0.77, 0.80, 0.75, 0.94, and 0.96. Therefore, additional correlation analysis using ANOVA was conducted in order to comprehend the sufficiency of the results produced from models, and the results are displayed in Table 7. Table 7ANOVA results showing the importance of several modes.SourceVMAVAVFBMSFLOW VALUETSRRM(T)RM(UN-T)Model0.0014*0.001*0.002*0.001*0.003*0.004*< 0.0001*< 0.0001*X₁0.03*0.04*0.02*0.03*0.01*0.220.05-X₂0.790.410.090.070.060.070.360.38X₃------0.004*0.001*X₄-------0.04*X₁X₂0.65-----0.48-X₁X₃------0.34-X₁X₄------0.1980.21X₂X₃-------0.03*X₂X₄-------0.15X₁²0.33-----0.65-X₂²0.11-----0.060.09X₃²------0.001*0.19X₄²-------0.03* Model type QuadraticLinearLinearLinearLinearLinearQuadraticQuadratic ANOVA results showing the importance of several modes. Table here shows that p-values in the models were significant enough (i.e., < 0.05) to produce trustworthy results at the 95% confidence level. As a result, as seen in Figs. 3 and 4, they were also utilized to create the optimization process-based response surface plots48. Water resistance and volumetric property surface plots. Surface plots of stiffness. Volumetric properties Figure 3 illustrates the changes in volumetric characteristics, such as VMA, VA, VFA, MS, and FLOW VALUE, when CWAs are used as WC construction materials49. With the exception of VMA, all of the volumetric attributes had a linear connection with the process parameters, according to the response surface plots. These results further demonstrate that, in accordance with the MoRTH 2009 requirements for WC, the use of CWAs had no multiple effects on any of the volumetric parameters other than VFA. Among the other volumetric characteristics, several specimens’ VMA failed to meet the standards when the proportions of BC (VG30) and CWAs were 4% and 10%, respectively. Additionally, it was found that specimens with 40% and 4%, 3.78% and 5%, of the CWAs and the BC (VG30) were unfit for WC building due to compromised VA values. The fact that MS and FLOW VALUE were found to be within the specifications required for the development of WC for the complete specimen, as designed in the lab, was encouraging, nevertheless50. A low percentage of CWAs in the specimen could have a substantial impact on the VMA, VA, and VFA, according to observations made utilizing the volumetric characteristics. Therefore, when deciding how many CWAs to utilize in the construction of the WCs, much thought should be given. The two-way ANOVA results, as presented in Table 7, also demonstrated that the percentage of CWAs is significantly (< 0.05) correlated with the volumetric features, although this is not the case for the percentage of bitumen content. Therefore, it also supports the conclusion that the percentage of CWAs should be carefully determined in order to achieve the necessary WC characteristics51. Water resistance When mortar is applied to CWAs, it has been shown to improve their ability to absorb water and decrease resistance. As a result, Fig. 3 displays the results of this study’s analysis of the specimen’s tensile strength ratio (TSR) at various CWA proportions. Table 7; Fig. 3 show that bitumen pre-treatment of the CWAs has decreased their permeability because the majority of the specimens had TSR within the acceptable ranges. The only specimen with TSR values greater than 90% was the one with CWAs and BC contents of 25% and 6.41%, 3.78% and 5%, 10% and 6%, respectively. Additionally, two-way ANOVA analysis revealed no significant relationship between TSR and the percentage of CWAs in the sample. Therefore, it may be inferred that the bitumen emulsion pre-treatment improved the CWAs’ properties and caused them to behave more like natural aggregates52. Stiffness The resilient modulus (RM) of the epoxy determined the stiffness of the specimen created using CWAs. The RM of the CWA specimens that were treated and those that were not was compared. Both untreated and treated specimens had average RM values above 5000 MPa, which was the standard RM value for WC. Consequently, it could be concluded that the specimen created using the treated CWAs behaves similarly to natural mixtures and does not decrease its RM53. Conversely, it was shown that substituting treated CWAs for the untreated ones reduced the specimen’s stiffness. Thus, it is also possible to deduce that the specimen’s rigidity decreases as the bitumen content rises54. Additionally, variations in the specimen’s stiffness in relation to the ambient temperature were assessed in order to gauge the effects of weather on the specimen. Figure 4 response surface plots demonstrate that the specimen’s stiffness and temperature had a quadratic relationship. It was evident that the rigidity of the specimen—both treated and untreated—decreased as the temperature rose. Both specimen types were found to be more rigid at lower temperatures. Nevertheless, it was discovered that the untreated specimens were stiffer than the treated ones when the effects of temperature were ignored55. Likewise, a two-way ANOVA showed a stronger correlation between the specimen’s temperature and RM, followed by the proportion of the CWAs. Optimization The best circumstances for the procedure and responses were further assessed using statistical frameworks and reaction surface plots produced by Design Expert software. Table 8 lists the values of the several procedure and response parameters that were noted under ideal circumstances56. Table 8Optimum conditions for response parameters.Response parametersOptimized conditionProportion of treated CWAs (%)Bitumen (VG 30) content (%)TemperatureVMA14.34%21.024.79-VA3.99%21.024.79-VFB77.71%21.024.79-MS20.76 kN21.024.79-FLOW VALUE2.42 mm21.024.79-TSR88.43%21.024.79-RM(T)11687.6 MPa21.024.799.9 Optimum conditions for response parameters. Table 8 suggests that, under ideal circumstances, such as pre-treated CWAs = 21.02%; bitumen (VG30) = 4.79%; and temperature = 9.9 °C, all of the response parameters’ values fell within the MoRTH (2000) specified bounds. Therefore, it was determined that the tests created in this study utilizing the Design Expert program were appropriate for determining the ideal process parameter settings that would allow for the preparation of appropriate building material for WC57. Conclusions When building WCs, the results of the current investigation shown that CWAs recovered from a road maintenance site in a mountainous region of India could significantly replace natural aggregates. It has been demonstrated that bitumen emulsion pre-treating the CWAs enhances their qualities and makes them suitable for use in building. The characteristics of the laboratory specimen that were found to be similar to those of the natural aggregates included its VMA, VA, VFA, MS, FLOW VALUE, TSR, and RM. Additionally, the RSM optimization procedure revealed that all of the response parameters’ values fell within the MoRTH (2000) specified bounds under optimal conditions, which included pre-treated CWAs = 21.02%; bitumen (VG30) = 4.79%; and temperature = 9.9 °C. Bitumen pre-treatment improves the Tensile Strength Ratio (TSR) primarily by enhancing the adhesion between the asphalt binder and concrete waste aggregates (CWAs) and by reducing moisture susceptibility. Untreated CWAs generally possess a porous surface texture and residual cement mortar, which absorb more water and weaken the bond between aggregate and bitumen. This weak interfacial bonding promotes stripping and reduces moisture resistance in asphalt mixtures. The bitumen emulsion pre-treatment forms a thin coating around the surface of CWAs, which acts as a protective layer and minimizes water absorption. This coating improves the aggregate–binder affinity, fills surface pores and microcracks, and creates a stronger interfacial bond within the asphalt matrix. As a result, the treated aggregates exhibit better resistance against moisture-induced damage and stripping under wet conditions. Consequently, the asphalt mixtures prepared with pre-treated CWAs show higher TSR values, indicating improved durability, cohesion, and long-term pavement performance. The decrease in stiffness with treated concrete waste aggregates (CWAs) can be attributed to the presence of the bitumen emulsion coating on the aggregate surface. The pre-treatment creates a relatively softer and more flexible interfacial layer between the aggregate and asphalt binder compared to untreated aggregates. While this coating improves adhesion and moisture resistance, it also reduces the rigidity of the aggregate skeleton within the asphalt mixture. As a result, it was concluded that laboratory specimens made in compliance with multivariate experiments—specifically, CCD and BBD—were appropriate for use in the production of WC. As a result, it is suggested that the CWAs be kept and that their repurposing for construction be encouraged. This could help with the many efforts being carried out globally to meet the deadlines for achieving various sustainable development goals. Acknowledgements (No data analysis or data generated for the study). Author contributions V.D.: Investigation, material preparation, data curation, writing—original draft; S.S.: Conceptualization, writ-ing—review & editing; P.R.: Formal analysis, mix design optimization; K.Y.: Mineralogical characterization, data interpretation; V.D.: Methodology, experimental design; S.S.: Supervision, resources; S.S.: Manuscript revi-sion S.P.: Writing—review & editing; P.S.: Writing—review & editing, technical editing. Data availability (No data analysis or data generated for the study). Declarations Competing interests The authors declare no competing interests. Footnotes Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References Associated Data Data Availability Statement (No data analysis or data generated for the study).