Design and field validation of an automated sensor-integrated high-capacity corn plot seeder Authors: Yan Ye Published: 2026 ABSTRACT Efficient and accurate plot seeding is essential for modern crop breeding and precision agriculture. However, existing systems demonstrate limitations in terms of automation, throughput, and sensing capabilities. To address these challenges, an automated, sensor-integrated, high-capacity planting system was developed for corn plot seeders. The mechanical dynamics of seed delivery were analyzed, and key parameters, including opener tip angle, tilt angle, pushrod speed, and opening position, were optimized using response surface methodology. The optimal parameter combination (30°, 49°, 90 mm/s, and − 9 mm, respectively) yielded a seeding qualification rate of 99.33%. A three-stage sensor module comprising QR code recognition, cartridge positioning, and seed-drop detection was integrated to ensure accurate seed–plot matching. Field experiments demonstrated a 76% reduction in manual intervention, with an error tolerance of 0.1%. Therefore, the proposed system provides an effective and scalable solution for precision plot seeding and offers a practical framework for upgrading existing agricultural equipment. Introduction Chinese plot seeders continue to exhibit technological limitations compared to their international counterparts1–3. The global market is currently dominated by advanced models developed by industry leaders such as Wintersteiger (Austria), Almaco (USA), and Haldrup (Germany)4,5. These systems feature sophisticated automated planting technologies that not only fulfill automatic seeding requirements but also significantly improve operational efficiency6,7. The planting system is a core component of the plot seeder8 and plays a critical role in plot breeding and seeding operations9. At present, agricultural practices in China predominantly rely on manual seeding methods, using either cone systems (gravity-fed funnels through which seeds flow into furrows) or magazine systems (cartridge-based dispensers requiring manual reloading after several plots)10–13. In contrast, automated high-capacity planting systems offer clear operational advantages over these traditional approaches. In particular, these systems can enable precise seed spacing within sowing plots, the continuous planting of multiple seed varieties, and the automated collection of used seed cartridges. Extensive research has been conducted globally to enhance planting efficiency and performance. Current planting systems for plot seeders can be broadly classified into two categories: manual and automatic. Manual seeding involves pre-distributing seeds into individual paper bags, which are then manually delivered using a central seed dispenser. However, this method is labor-intensive and makes maintaining seeding precision and uniformity challenging. For instance, Liu et al.14 designed an electromagnetically driven coaxial double-disc automatic planting system that was compatible with plot breeding and seeding equipment. However, its application was limited to a small number of plots. Meanwhile, Xu et al.15 developed a cone-belt seed metering device for plot seeders, but its seeding uniformity was sensitive to cone structure and the seed distribution speed. In addition, Engel et al.16 designed a manual plot seeder and fertilizer applicator using a simple seed cartridge device produced by Hege. Moreover, Yuan et al.17 developed an oil–electric hybrid air-suction sorghum plot seeder to improve seeding accuracy and reduce seed damage, but its specialized configuration limited its applicability to sorghum and similarly sized grains. For theoretical optimization, Ma et al.18 proposed a seeding-trajectory-based farmland boundary estimation method using curvature analysis and clustering, enabling efficient and accurate digital mapping for agricultural automation. Moreover, Zhao et al.19 optimized a hand-pushed precision planter by determining optimal hole dimensions and chamber angles through EDEM simulation and orthogonal testing, addressing the issues of low flexibility, high cost, and poor sowing quality in existing corn breeding seeders. Beres et al.20 developed two fully operational prototype drills to overcome the limitations of conventional drills for conservation farming and to enable the accurate replication of zero-tillage practices in field plot studies. Automatic seeding systems, in contrast, rely on preloaded seed cartridges that are delivered via a magazine-type automated planting mechanism. While this method is suitable for small-scale breeding and seeding trials, it requires the frequent manual replacement of seed cartridges in larger trials, leading to potential delays and replacement errors during prolonged operation. Li et al.21 designed a seed distributor equipped with a magazine system for precision plot seeders, thereby reducing the number of operators required during trials. Wang22 developed an automatic seed delivery system for soybean plot seeders, although its application was limited to continuous seeding for up to 12 plot groups per cycle. Tabal et al.23 employed a mechatronic planting system for a simple hand-pushed corn seeder. More recently, Almaco (USA) introduced a large-scale automated planting system equipped with a magazine system, capable of seeding 5,760 plots when fully loaded24. However, the high cost of importing such devices remains a significant barrier. Moreover, the proprietary cartridge design and fixed opener kinematics of this system restrict its adaptability to variable domestic conditions across China. Similarly, Haldrup’s systems lack integrated seed–plot verification sensors, which can lead to mismatches during field trials25,26. This study addresses several challenges in existing plot seeder planting processes, including high operational intensity during planting and cartridge replacement, difficulties in maintaining seeding precision, limited planting areas, and the high cost of imported systems. To overcome these limitations, an automated, high-capacity planting system for corn plot seeders was developed to provide a reference framework for future research. Unlike existing systems, the proposed system offered three key improvements tailored to practical requirements: real-time sensory verification, adaptive opener kinematics, and an open retrofitting platform. Its design was based on three core hypotheses: (1) optimization of opener geometry and kinematic parameters would increase seeding qualification rates; (2) integration of a three-stage sensing system would reduce seed–plot mismatches; and (3) the system would decrease manual intervention while maintaining field operational speeds. Key performance indicators, including seeding qualification rate, error tolerance, labor reduction, and cartridge cycle time, were used to evaluate the improvements achieved by this system. The remainder of this paper is organized as follows. Section “Structure and working principles” presents the structure and operating principles of plot seeders. Section “Design of key components” describes the key design components. Section “Mechanical analysis of the seed dispensing process of the planting system” models the seed dispensing process of the planting system. Section “Experimental design” details the experimental validation of the proposed system, while Section “Results and discussion” discusses the results. Finally, Section “Discussion” concludes the study and outlines its limitations. Structure and working principles Structure composition As a primary working component of a plot seeder, the planting system plays a crucial role in regulating seed quantity and influencing the overall seeding quality27. The structure of the automated high-capacity planting system is illustrated in Fig. 1a. The system primarily consists of four main subsystems: the storage cart components, the planting components, the seed cartridge collection components, and the storage cart sliding platform. The planting and cartridge collection components include the base plate, seed cartridge pushrod, tow hook on the cartridge support rod, seed cartridge opener, slider rail, DC servo motor, synchronous belt, synchronous belt pulley, and fixed plate. The DC servo motor provides the driving force for the movement of the storage cart and seed cartridges, while the base plate is designed with openings for seed discharge and the collection of used seed cartridges. To clearly explain the system configuration and facilitate a better understanding of its practical implementation, photographs of the prototype are provided in Fig. 1b–d. As shown in Fig. 1b, the overall configuration of the automated planting system includes the storage cart, planting mechanism, and guide rail assembly. Figure 1c illustrates the internal layout, highlighting the transport path of the seed cartridge and the location of the recognition module within the operating channel. In addition, the installation position of the sensor module is depicted in Fig. 1b, while its structural details are presented in Fig. 1d. The QR code recognition module is mounted along the seed cartridge transport path to enable the real-time identification and verification of seed cartridges during operation. Fig. 1Structure and configuration of the automated high-capacity planting system. (a) Schematic diagram depicting the configuration of the system: 1. Storage cart components; 2. Seed cartridge; 3. Storage cart cover; 4. Tow hook on the support rod of the storage cart; 5. Compactor of the storage cart; 6. Slider; 7. Rail; 8. DC servo motor; 9. Seed discharge port; 10. Seed cartridge collection device; 11. Planting and seed cartridge collection components; 12. Seed cartridge opener; 13. Seed cartridge holder; 14. Storage cart sliding platform; 15. Divider. (b) Overall view of the prototype; (c) Internal structure showing the seed cartridge transport path and recognition module; (d) QR code recognition module and the PCB control unit for seed cartridge identification. Structure and configuration of the automated high-capacity planting system. (a) Schematic diagram depicting the configuration of the system: 1. Storage cart components; 2. Seed cartridge; 3. Storage cart cover; 4. Tow hook on the support rod of the storage cart; 5. Compactor of the storage cart; 6. Slider; 7. Rail; 8. DC servo motor; 9. Seed discharge port; 10. Seed cartridge collection device; 11. Planting and seed cartridge collection components; 12. Seed cartridge opener; 13. Seed cartridge holder; 14. Storage cart sliding platform; 15. Divider. (b) Overall view of the prototype; (c) Internal structure showing the seed cartridge transport path and recognition module; (d) QR code recognition module and the PCB control unit for seed cartridge identification. Working principle Before the planting system is operated, seed cartridges (each row pre-filled with seeds) are first arranged in compartments separated by dividers according to the designated plot sequence. The storage cart is then placed on the sliding platform. A push–pull cartridge compactor, connected by a linkage mechanism, drives the three compactors to secure the storage cart, while the tow hook on the support rod of the storage cart engages with the support rod of the seed cartridges. During operation, the DC servo motors provide the driving force. DC servo motor 1 drives the synchronous belt via a pulley, causing the storage cart’s sliding platform to move along the rail toward the right. This causes the movement of the storage cart. Throughout this movement, the tow hook on the storage cart support rod constrains the movement of the seed cartridge support rod. Guided by position sensors, the storage cart moves to a predetermined position, where a seed cartridge is released onto the holder. Once the seed cartridge is in position, DC servo motor 2 is activated, driving a second synchronous belt via a pulley system. This action moves the seed cartridge pushrod along the rail toward the right, pushing the seed cartridge from the holder to the opener. The opener causes the seed cartridge to open, allowing seeds to fall through the discharge port. The empty seed cartridge then continues to move backward and is collected by the cartridge collection unit. The DC servo motor drives the pushrod of the seed cartridge in a reciprocal manner, enabling the continuous dispensing of all seed cartridges within the storage cart. Throughout the dispensing process, position sensors and seed cartridge code recognition sensors ensure that all seed cartridges are correctly dispensed. After all seed cartridges have been dispensed, the DC servo motors return all components to their initial positions. The main technical parameters of this automated high-capacity planting system are summarized in Table 1. Table 1Key technical parameters.ParametersSpecificationOverall dimensions(Length × Width × Height)/(mm × mm × mm)1340 × 250 × 892Number of seeding rows2Number of seeding furrows2Operational speed of plot seeder (km/h)2.0–2.5Number of seed cartridges per containerApproximately 200Planting time interval of seed cartridges (s)≤ 4.5 Table 1Key technical parameters.ParametersSpecificationOverall dimensions(Length × Width × Height)/(mm × mm × mm)1340 × 250 × 892Number of seeding rows2Number of seeding furrows2Operational speed of plot seeder (km/h)2.0–2.5Number of seed cartridges per containerApproximately 200Planting time interval of seed cartridges (s)≤ 4.5 Key technical parameters. Overall dimensions (Length × Width × Height)/(mm × mm × mm) To further illustrate the coordination between the sensor module and the actuator system, the control logic of the automated planting system is presented in Fig. 2. The proposed system employs a three-stage sensing module to ensure accurate seed cartridge handling and reliable seed delivery. The sensing module comprises: (1) a seed cartridge detection sensor, (2) a recognition sensor based on QR code identification, and (3) a seed drop monitoring sensor. These sensors are strategically installed along the seed cartridge transport path. The detection sensor is installed at the cartridge loading position to verify the presence of the cartridge. Meanwhile, the recognition sensor is positioned at the identification station to ensure correct seed–plot matching. Finally, the seed drop monitoring sensor is located near the discharge outlet to confirm successful seed release. Sensor signals are transmitted to a PLC-based control system, which coordinates actuator operations sequentially. During operation, the system first performs initialization and self-check. Upon receiving the start command, the cartridge is transported to the target position. The pushrod mechanism is then activated based on sensor feedback to open the cartridge. The recognition sensor verifies that positioning is correct, and the seed drop sensor confirms the successful release of seeds. If abnormalities such as blockage or misalignment are detected, the system initiates an error-handling procedure and resets to ensure safe operation. Sensor signals are continuously sampled and processed in real time by the control unit, leading to synchronized sensing and actuation operations. Fig. 2Control logic diagram of the automated planting system based on sensor–actuator coordination. Control logic diagram of the automated planting system based on sensor–actuator coordination. To further highlight the integration of the mechanical system and the sensing module, a closed-loop control mechanism based on real-time sensor feedback is established, as summarized in Table 2. During operation, the three-stage sensing module continuously monitors system states, including seed cartridge presence, identification accuracy, and seed release status. These signals are transmitted to a PLC controller, which dynamically adjusts actuator parameters such as pushrod displacement, operation timing, and motor motion. When abnormal conditions such as misalignment, blockage, or recognition failure are detected, the control system immediately triggers corrective actions, including repositioning, repeated verification, or system reset. This feedback-driven adjustment ensures that the seed delivery process remains stable and accurate under varying operating conditions. Accordingly, the proposed system achieves the collaborative optimization of mechanical and sensing processes, forming an adaptive control framework that significantly improves operational reliability and performance. Table 2Performance evaluation indicators for the automated seed-feeding system and corresponding measurement methods.Parameter categorySpecific measured parameterMeasurement methodQualification thresholdReference standardCore seed-feeding performanceSeed-feeding accuracyNumber of correctly delivered seed cartridges/Total number of delivered seed cartridges≥ 99.5%GB/T 6973–2005Core seed-feeding performanceMisdelivery rateNumber of mismatched seed cartridges/Total number of delivered seed cartridges≤ 0.2%Enterprise standardCore seed-feeding performanceMissed delivery rateNumber of undischarged seed cartridges/Total number of delivered seed cartridges≤ 0.3%Enterprise standardCore seed-feeding performanceSensor recognition success rateNumber of successfully decoded seed cartridges/Total number of scans≥ 99.8%Enterprise standardCore seed-feeding performanceSeed-drop qualification rateNumber of seed cartridges with 48–52 seeds dropped/Total number of seed cartridges≥ 98%GB/T 6973–2005Operational efficiencySingle-cartridge seed-feeding timeAverage time from cartridge drop to recycling completion≤ 2.5 sDesign requirementOperational efficiencyContinuous seed-feeding speedNumber of plots completed per hour≥ 1440 plots/hDesign requirementOperational efficiencyAccurate re-delivery rate after interruptionNumber of seed cartridges correctly delivered after fault recovery100%Design requirementWorking-condition adaptabilityAdaptable opener angle rangeSeed-feeding stability at 30°–45°Optimum at 35°EDEM simulation verificationWorking-condition adaptabilityAdaptable pushrod operating speed rangeSeed-feeding performance at 0.15–0.25 m/sOptimum at 0.2 m/sBench testWorking-condition adaptabilityContinuous operating durationFault-free continuous seed-feeding duration≥ 1 hReliability testFault and reliabilityCartridge jamming rateNumber of cartridge jams during operation/total number of delivered cartridges≤ 0.1%Enterprise standardFault and reliabilityBlockage rateNumber of outlet blockage events/Total number of delivered cartridges≤ 0.1%Enterprise standardFault and reliabilityMotor temperature riseMotor surface temperature after 8 h of continuous operation≤ 75 °CGB 755–2019 Table 2Performance evaluation indicators for the automated seed-feeding system and corresponding measurement methods.Parameter categorySpecific measured parameterMeasurement methodQualification thresholdReference standardCore seed-feeding performanceSeed-feeding accuracyNumber of correctly delivered seed cartridges/Total number of delivered seed cartridges≥ 99.5%GB/T 6973–2005Core seed-feeding performanceMisdelivery rateNumber of mismatched seed cartridges/Total number of delivered seed cartridges≤ 0.2%Enterprise standardCore seed-feeding performanceMissed delivery rateNumber of undischarged seed cartridges/Total number of delivered seed cartridges≤ 0.3%Enterprise standardCore seed-feeding performanceSensor recognition success rateNumber of successfully decoded seed cartridges/Total number of scans≥ 99.8%Enterprise standardCore seed-feeding performanceSeed-drop qualification rateNumber of seed cartridges with 48–52 seeds dropped/Total number of seed cartridges≥ 98%GB/T 6973–2005Operational efficiencySingle-cartridge seed-feeding timeAverage time from cartridge drop to recycling completion≤ 2.5 sDesign requirementOperational efficiencyContinuous seed-feeding speedNumber of plots completed per hour≥ 1440 plots/hDesign requirementOperational efficiencyAccurate re-delivery rate after interruptionNumber of seed cartridges correctly delivered after fault recovery100%Design requirementWorking-condition adaptabilityAdaptable opener angle rangeSeed-feeding stability at 30°–45°Optimum at 35°EDEM simulation verificationWorking-condition adaptabilityAdaptable pushrod operating speed rangeSeed-feeding performance at 0.15–0.25 m/sOptimum at 0.2 m/sBench testWorking-condition adaptabilityContinuous operating durationFault-free continuous seed-feeding duration≥ 1 hReliability testFault and reliabilityCartridge jamming rateNumber of cartridge jams during operation/total number of delivered cartridges≤ 0.1%Enterprise standardFault and reliabilityBlockage rateNumber of outlet blockage events/Total number of delivered cartridges≤ 0.1%Enterprise standardFault and reliabilityMotor temperature riseMotor surface temperature after 8 h of continuous operation≤ 75 °CGB 755–2019 Performance evaluation indicators for the automated seed-feeding system and corresponding measurement methods. Design of key components Calculation of seed quantity for a single plot The internal structural dimensions of the seed cartridge serve as a key determinant of the overall size of the planting system. Typically, the seed spacing for corn plot seeders ranges from 30 to 40 cm, alongside a row spacing of 0.5–0.6 m. However, for summer corn, the seed spacing is typically between 25 and 33 cm. To facilitate subsequent experiments, a seed spacing of 30 cm and a row spacing of 0.5 m were selected to calculate the total seed quantity required for a single plot, as follows:1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Q=\left(\left[\frac{L}{P}+\left(\frac{L}{P}\times n\right)\right]\right)\times r$$\end{document} Herein Q—Total seed quantity for a single plot; L—Planting length (m); P—Seed spacing (cm); n—Excess seed ratio (approximately 10%); r—Number of planting rows. The excess seed ratio n compensates for potential seed losses. Planting an excess number of seeds can lead to issues such as seed mixing and delays in the subsequent seed clearing process. Given existing seeding equipment, an excess seed ratio of about 10% is appropriate for the planting area of a single plot. For a minimum plot area of 2 m2, each planting row should include an additional two to three seeds to prevent issues such as seed shortage or uneven distribution during the subsequent seed dispensing process. The plot seeding area can be calculated using the following formula:2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$S=R\times N \times L$$\end{document} Herein S—Plot seeding area (m2); R—Row spacing (cm); N—Number of rows; L—Total planting length (m). Based on the above calculations, a plot with a maximum area of 8 m2 requires approximately 58.7 corn seeds. Unlike field seeding, plot seeding requires a specific quantity of seeds for smaller plots11,27,28, and the plot seeding area typically ranges from 2 to 8 m2. Design of the structural parameters of the seed cartridge Issues such as the premature opening of the seed cartridge or its failure to open during planting can result in seed spillage or missed seeding. To prevent such issues, the seed cartridge is designed such that it contains an opening on the long side, allowing the seed cartridge opener to work effectively. Meanwhile, the short side is equipped with a fold-over slot that connects the upper cartridge and the bottom cover, preventing the bottom cover from falling into the seed dispenser. For our analysis, a random sample consisting of 100 seeds belonging to three corn varieties widely cultivated in the Harbin region—Ruipu 909 (blue), Yangguang No. 1 (red), and Dongnong 248 (yellow)—was selected. The volume of the corn kernels was measured using graduated cups. Among the three varieties, Yangguang No. 1 showed the highest volume (100 seeds = approximately 60 ml), while Dongnong 248 showed the lowest volume (100 seeds = 35 ml). The volumes of the different corn seeds are illustrated in Fig. 3. Fig. 3Size and volume of different corn seeds. Size and volume of different corn seeds. Considering that seed quantity must be an integer in practical scenarios, this parameter was set to 60. The volume of 60 Yangguang No. 1 seeds was calculated to be approximately 36 ml. Therefore, a seed cartridge with a volume of 45 ml could meet the seeding requirements for a maximum plot area of 8 m2 (with each seed cartridge having some margin to accommodate seeds belonging to other varieties and meet the seeding requirements for larger plots). The volume of each seed cartridge can be calculated as follows:3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$V=L\times H \times W$$\end{document} Herein V = Volume of a single seed cartridge (ml); L = Length of the seed cartridge (mm); H = Height of the seed cartridge (mm); and W = Width of the seed cartridge (mm). After calculations, L = 80 mm, W = 42 mm, and H = 15 mm were selected as the dimensions of the seed cartridge. The structure of the seed cartridge is shown in Fig. 4. Fig. 4Structure of the seed cartridge. Structure of the seed cartridge. Structural design of the storage cart and fixed platform The dimensions of the storage cart are determined based on the dimensions of the seed cartridges and the number of plots that require sowing. Given the space within existing plot seeders and the number of plots, the dimensions of the storage cart are set to 574 mm × 114 mm × 660 mm, allowing it to accommodate approximately 200 seed cartridges. To monitor the number of seed cartridges within the container, one side of the storage cart is equipped with an acrylic (transparent) cover, as shown in Fig. 5. Fig. 5Structure of the storage cart. 1. Body; 2. Divider; 3. Acrylic (transparent) corner support plate; 4. Bracket; 5. Connecting rod; 6. Support rod; 7. Push–pull cartridge compactor; 8. Limit block; 9. Seed cartridge; 10. Acrylic (transparent) storage cart cover; 11. Handle. Structure of the storage cart. 1. Body; 2. Divider; 3. Acrylic (transparent) corner support plate; 4. Bracket; 5. Connecting rod; 6. Support rod; 7. Push–pull cartridge compactor; 8. Limit block; 9. Seed cartridge; 10. Acrylic (transparent) storage cart cover; 11. Handle. The movement of the storage cart platform and the planting pushrod is controlled by a PWM-regulated DC servo motor, allowing for adjustable speeds. The DC servo motor transmits power to the storage cart sliding platform and the planting pushrod via synchronous belt pulleys and belts. The planting and seed cartridge collection components are shown in Fig. 6. Fig. 6Structure of the planting and seed cartridge collection components. 1. Tow hook on the support rod of the seed cartridge; 2. Base plate; 3. Slider; 4. Rail; 5. Motor; 6. Seed discharge port; 7. Seed cartridge collection port; 8. Baffle; 9. Seed cartridge opener; 10. Seed cartridge identification (barcode/QR code verification scanner); 11. Seed cartridge pallet; 12. Synchronous belt pulley; 13. Pushrod bracket; 14. Seed cartridge pushrod; 15. Connecting bracket for the storage cart sliding platform. Structure of the planting and seed cartridge collection components. 1. Tow hook on the support rod of the seed cartridge; 2. Base plate; 3. Slider; 4. Rail; 5. Motor; 6. Seed discharge port; 7. Seed cartridge collection port; 8. Baffle; 9. Seed cartridge opener; 10. Seed cartridge identification (barcode/QR code verification scanner); 11. Seed cartridge pallet; 12. Synchronous belt pulley; 13. Pushrod bracket; 14. Seed cartridge pushrod; 15. Connecting bracket for the storage cart sliding platform. Determination of planting time The typical operating speed for small plot seeders ranges from 2.0 to 2.5 km/h. To ensure adequate time for planting29, agronomic requirements and actual seeding conditions must be considered. A plot seeder efficiently seeds a two-row, 2 m2 plot in roughly 3.6 s; however, when tasked with seeding a two-row, 8 m2 plot, the time required rises to approximately 14.3 s. The total planting time should be less than half of the total operation time for a single plot (including the time taken for the seed cartridge to move from the initial point to the seed discharge port, the time taken for seeds to be released from the seed cartridge to the seed dispenser, and the time taken for the seed dispenser to move seeds to the seeding position on the seed metering device). In reference to the operation time of the chain-type planting system of the 2BQX-2 pull-type plot seeder developed by the Heilongjiang Academy of Agricultural Machinery Engineering, and considering parameters such as the planting length of the corn plot, operation time, and the forward speed of the plot seeder (planting system), the planting time for the automated high-capacity planting system can be calculated as follows:4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$L=v_{1}\times \left(t_{1}+t_{2}\right)$$\end{document}5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left(t_{1}+t_{2}\right)\leq\frac{T}{2}$$\end{document}6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$t_{1}\approx t_{2}$$\end{document} Herein L—Plot length (m); v1—Forward speed of the plot seeder (m/s); T—Total operation time within a single plot before moving to the next plot (s); t1—Time taken for the seed cartridge to move from the initial point to the seed discharge port (s); t2—Time taken for seeds to be released from the seed cartridge to the seed dispenser (s). These calculations suggest that under ideal working conditions, it takes approximately 4.6 s for a plot seeder to complete seeding a two-row, 2 m2 plot and move to the subsequent plot (roughly 1 s for the 0.8 m plot spacing and approximately 3.6 s for the completion of planting a two-row, 2 m2 plot). The planting system must thus complete the operation for the previous plot within 2.3 s before seeding the next plot to meet planting requirements. The plot area is illustrated in Fig. 7. Fig. 7Plot area. Initial position of the planting system of the plot seeder. Plot area. Initial position of the planting system of the plot seeder. Mechanical analysis of the seed dispensing process of the planting system Force and motion analysis during seed delivery The planting system involves a significant amount of particle motion. This motion is influenced by various forces, including gravity. To characterize the forces and motion of seeds within the cartridge, an analysis of the planting process is necessary. Since the air resistance acting on corn particles during free fall is negligible1,30,31, their motion after exiting the cartridge is governed predominantly by gravity and can be approximated as linear free-fall motion in accordance with Newton’s second law. A Cartesian coordinate system can be considered, with the centroid of a seed inside the cartridge serving as the origin, the horizontal line passing through the origin acting as the x-axis, and the vertical line acting as the y-axis. The forces acting on an individual seed include tangential resistance ft, the normal support force N from the bottom cover of the seed cartridge, the pressure from the upper seed layer Nj, the gravitational force G, and the normal support force from the lower seed layer Nv. Based on this force and motion analysis, the corresponding velocity equations of seed motion can be obtained as follows:7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$V_{x}=V_{d}$$\end{document}8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$V_{y}=V_{p}+gt$$\end{document}9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$V_{p}=gt$$\end{document} Under known conditions, the fundamental motion state of corn seeds as they exit the cartridge can be characterized. The seed trajectory and associated force interactions are illustrated in Fig. 8. Fig. 8Force analysis of the seed cartridge during the planting process. 1. Seed cartridge pushrod; 2. Seed cartridge and corn seeds; 3. Seed cartridge slide; 4. Seed cartridge opener; 5. Seed discharge port. Note: Vp is the vertical velocity of the seed (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{m}\,{\mathrm{s}}^{-1}$$\end{document}); Vd is the velocity of the seed cartridge pushrod along the direction of operation (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{m}\,{\mathrm{s}}^{-1}$$\end{document}); Lis the distance from the initial position of the seed cartridge to the seed delivery position (mm); Vx is the normal velocity of the seed cartridge along its direction of travel; Vy is the tangential velocity of the seed cartridge along its direction of travel. Force analysis of the seed cartridge during the planting process. 1. Seed cartridge pushrod; 2. Seed cartridge and corn seeds; 3. Seed cartridge slide; 4. Seed cartridge opener; 5. Seed discharge port. Note: Vp is the vertical velocity of the seed (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{m}\,{\mathrm{s}}^{-1}$$\end{document}); Vd is the velocity of the seed cartridge pushrod along the direction of operation (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{m}\,{\mathrm{s}}^{-1}$$\end{document}); Lis the distance from the initial position of the seed cartridge to the seed delivery position (mm); Vx is the normal velocity of the seed cartridge along its direction of travel; Vy is the tangential velocity of the seed cartridge along its direction of travel. Seed cartridge travel analysis The post-collision velocities v1 and v2 of corn particles can be determined based on the conservation of momentum and the coefficient of restitution. This approach models momentum exchange during particle interactions within the seed cartridge. For two colliding particles with masses m1 and m2, the post-collision velocities are distributed around the velocity of their center of mass. The relative velocity after collision is expressed as e(v1-v2), where e is the coefficient of restitution, representing collision elasticity. Since the corn particles have approximately equal mass, their velocities effectively exchange upon collision, in line with the laws of momentum conservation:10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$m_{1}v_{1}+m_{2}v_{2}=m_{1}v_{1}^{\prime}+m_{2}v_{2}^{\prime}$$\end{document} The coefficient of restitution can be calculated as follows:11\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$e={\frac{{v_{1}}^{\prime}-{v_{2}}^{{\prime}}}{v_{1}-v_{2}}}$$\end{document} The velocities of the corn particles after collision can be calculated as follows:12\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$V=\frac{m_{1}{v}_{1}+m_{2}v_{2}}{m_{1}+m_{2}}+e(v_{1}-v_{2})\frac{m_{1}}{m_{1}+m_{2}}$$\end{document} During sowing, corn particles undergo complex motion under the combined influence of multiple forces such as gravity, inertia, and contact friction. To further examine seed dynamics within the cartridge, the planting process can be analyzed using a three-dimensional coordinate system, where the seeding direction is defined as the positive x-axis, the downward vertical direction as the positive z-axis, and the cartridge opening direction as the positive y-axis. The primary component influencing seed motion is the velocity Vx, which aligns with the cartridge’s direction of travel (x-axis). In practical applications, the overall planting speed can be regulated by adjusting the pushrod speed, which controls cartridge movement to meet specific sowing requirements. Analysis of seed delivery stages Assuming that corn particles glide smoothly and unhindered from the bottom cover of the seed cartridge into the seed metering device, and neglecting external influences such as air resistance, our analysis focuses on two dominant forces: gravity acting on the corn particles and friction between the particles and the cartridge cover. Using a simplified mechanical model, the motion of corn particles on the cartridge’s bottom cover can be divided into three stages: (1) an initial opening stage, in which particles rotate along with the cartridge cover around the axis of the bottom cover; (2) a sliding stage, in which particles begin to slide along the cover once the opening angle reaches a certain level; and (3) a projectile motion stage, in which particles are discharged and lose contact with the cover, following a parabolic motion with an initial velocity. This process is illustrated in Fig. 9. Fig. 9Force analysis of corn particles during the movement of the bottom cover of the seed cartridge. Force analysis of corn particles during the movement of the bottom cover of the seed cartridge. The transition between the first and second stages is defined by the critical sliding angle of the corn particle on the seed cartridge cover. This condition can be simplified to a slider-on-an-inclined-plane model, from which the critical angle can be derived as follows:13\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{2}^{\mathrm{1}}=arctan\,\mu$$\end{document} During the initial opening stage, the seed cartridge cover can be assumed to be closely aligned with the opener, as illustrated in Fig. 10. To clearly explain the geometric and functional differences between the opener tip angle and tilt angle, a systematic comparison is provided in Table 3. The tip angle (θ0) is defined as the included angle between the cutting edges of the opener tip and primarily influences cutting resistance and the initial opening behavior of the seed cartridge. In contrast, the tilt angle (θ1) is defined as the angle between the working surface of the opener and the horizontal plane, and it governs the opening motion of the seed cartridge and the trajectory of seed release. As summarized in Table 3, these two parameters differ in their reference definitions, mechanical functions, and effects on seed delivery performance. Specifically, the tip angle predominantly affects the cutting process and mechanical loading, whereas the tilt angle plays a critical role in controlling seed discharge behavior and flow stability. Therefore, both parameters must be jointly considered for the structural design and optimization of the planting system in order to achieve optimal seeding performance. Fig. 10Structural diagram of the seed cartridge and opener. (a) Tip angle of the opener; (b) Tilt angle of the opener. Structural diagram of the seed cartridge and opener. (a) Tip angle of the opener; (b) Tilt angle of the opener. Table 3Comparison of the θ0 and θ1 of the opener.Comparison itemTip angle θ0Installation tilt angle θ1DefinitionIncluded angle between the two cutting edges at the tip of the openerAngle between the working surface of the opener and the horizontal planeMeasurement referenceCutting edge surface of the opener itselfHorizontal planeCore functionCuts into the seed cartridge opening and affects the insertion resistance and initial opening widthGuides the bottom cover of the seed cartridge to fold downward and determines the opening speed and smoothness of seed dischargeEffect in EDEM simulationIf the angle is too small, jamming may occur; if it is too large, the motor load increasesIf the angle is too small, seed discharge is slow; if it is too large, seeds may bounce or scatterRecommended value for corn feeding30°–45°15°–30° Table 3Comparison of the θ0 and θ1 of the opener.Comparison itemTip angle θ0Installation tilt angle θ1DefinitionIncluded angle between the two cutting edges at the tip of the openerAngle between the working surface of the opener and the horizontal planeMeasurement referenceCutting edge surface of the opener itselfHorizontal planeCore functionCuts into the seed cartridge opening and affects the insertion resistance and initial opening widthGuides the bottom cover of the seed cartridge to fold downward and determines the opening speed and smoothness of seed dischargeEffect in EDEM simulationIf the angle is too small, jamming may occur; if it is too large, the motor load increasesIf the angle is too small, seed discharge is slow; if it is too large, seeds may bounce or scatterRecommended value for corn feeding30°–45°15°–30° Comparison of the θ0 and θ1 of the opener. Considering the shape of the opener, the following expression can be derived for the opening angle of the seed cartridge:14\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{2}=arcsin\left(\frac{s\,tan\,\theta_{0}\,sin\,\theta_{1}}{\sqrt{l_{0}^{2}+s^{2}\,tan^{2}\,\theta_{0}-2l_{0}s\,tan\,\theta_{0}\,cos\,\theta_{1}}}\right)$$\end{document} From the above equation, it is evident that the critical angle between the first and second stages is governed by the opener tip angle and tilt angle (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta_{0}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta_{1}$$\end{document}), as well as the lateral position of the opener (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$l_{0}$$\end{document}) and its insertion distance into the seed cartridge (s). The insertion distance is related to the pushrod velocity along the seeding direction and the duration of opener engagement with the cartridge:15\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s=v_{0}t$$\end{document} By combining Eqs. (13), (14), and (15), the time corresponding to the boundary between the first and second stages \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$t_{1}$$\end{document} can be determined. The transition between the second and third stages occurs when corn particles detach from the cartridge cover. This condition can be simplified as one where the rotational velocity of the corn particles around the axis of the cartridge cover becomes less than the rotational velocity at the contact point. By combining Eqs. (13) and (14), and taking first- and second-order derivatives with respect to time, the angular velocity (ω) and angular acceleration (α) of the seed cartridge cover can be obtained:16\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{{\begin{array}{l}\omega = \frac{{2A - D}}{{2A^{{\frac{3}{2}}} C^{{\frac{1}{2}}} }}v_{0} \,sin\, \theta _{1} \,tan\, \theta _{0} \\\alpha = \frac{{\left( {2A - tD} \right)^{2} }}{{4A^{{\frac{7}{2}}} C^{{\frac{3}{2}}} }}v_{0}^{3} t\,tan^{3} \theta _{0} \,sin^{3}\, \theta _{1} - \frac{{4v^{2} t + 4D - tD^{2} }}{{4A^{{\frac{3}{2}}} C^{{\frac{1}{2}}} }}v_{0} \,sin\, \theta _{1} \,tan\,\theta _{0} \\A = l_{0}^{2} - 2l_{0} v_{0} t\,tan\,\theta _{0} \,cos\, \theta _{1} + v_{0}^{2} t\,tan^{2}\, \theta _{0} \\B = v_{0}^{2} t^{2} \,tan^{2}\, \theta _{0} \\C = 1 - \frac{{v_{0}^{2} t^{2} \,tan^{2}\, \theta _{0} \,sin^{2}\, \theta _{1} }}{A} \\D = 2v_{0}^{2} t\,tan^{2}\, \theta _{0} - 2l_{0} v_{0} \,cos\, \theta _{1} \,tan\, \theta _{0} \\\end{array}} \right.$$\end{document} Prior to detachment, the corn particles remain in contact with the seed cartridge cover and therefore experience the same angular velocity around its axis. The boundary between the second and third stages is reached when the rotational acceleration of the corn particles is less than or equal to that of the seed cartridge cover. At this point:17\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta_{2}^{2}=arccos\,\frac{al}{g}$$\end{document} By combining Eqs. (14), (15), (16), and (17), the time corresponding to the transition between the second and third stages \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$t_{2}$$\end{document} can be calculated. The speed of the corn particle at distance l from the rotation axis of the seed cartridge cover during the first stage can be calculated as follows based on the above formulas:18\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{\begin{array}{l}v_{x}=v_{0}\\ v_{y}=-\omega l\,sin\,\theta_{2}\quad t\in[0,t_{1}]\\ v_{z}=\omega l\,cos\, \theta_{2}\end{array}\right.$$\end{document} During the second stage, the speed and acceleration of each corn particle can be determined by adding the sliding speed along the slope to the speed obtained during the first stage:19\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{l}v_{x} = v_{0} \\ v_{y} = \int_{{t_{1} }}^{t} \left( {sin\,\theta _{2} - \mu \,cos\, \theta _{2} } \right)dt\,sin\, \theta _{2} - \omega l\,sin\, \theta _{2} \quad t \in [t_{1} ,t_{2} ] \\ v_{z} = \int_{{t_{1} }}^{t} \left( {sin\, \theta _{2} - \mu\,cos\, \theta _{2} } \right)dt\,cos\, \theta _{2} + \omega l\,cos\, \theta _{2} \\ \end{array}} \right.$$\end{document} During the third stage, each corn particle follows a parabolic trajectory, with the speed at the end of the second stage acting as the initial velocity. Therefore:20\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{l} v_{x} = v_{0} \\ v_{y} = \int_{{t_{1}}}^{{t_{2}}} \left( {sin\,\theta _{2} - \mu\,cos\, \theta _{2} } \right)dt\,sin\, \theta _{2}^{2} - \omega l\,sin\, \theta _{2}^{2} \quad t \in [t_{1} , + \infty ] \\ v_{z} = \int_{{t_{1}}}^{{t_{2}}} \left( {sin\, \theta _{2} - \mu \,cos\, \theta _{2} } \right)dt\,cos\, \theta _{2}^{2} + g\left( {t - t_{2} } \right) \\ \end{array} } \right.$$\end{document} As indicated by Eq. (16), an excessively large opener tip angle \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{0}$$\end{document} may induce mechanical damage or seed jamming within the cartridge, adversely affecting planting performance. Furthermore, as shown in Eq. (14), increasing the tilt angle of the opener increases the opening angle of the seed cartridge, thereby reducing the seed discharge time. However, this also increases the likelihood of seed rebound from the cartridge cover during descent. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$l_{0}$$\end{document} is typically determined based on practical design requirements. In summary, the force analysis of the seeds and the seed delivery process reveals the key influence of the following seed cartridge structural and operational parameters: tip angle of the opener (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta_{0}$$\end{document}), tilt angle of the opener (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta_{1}$$\end{document}), and pushrod speed (Vd). Experimental design Experimental platform and field conditions To evaluate the operational effectiveness of the planting system under actual field conditions, a field trial was conducted. The device was installed on the 2BQX-2 pull-type plot seeder developed by the Heilongjiang Academy of Agricultural Machinery Engineering. During the trial, the overall operating speed of the machine was maintained between 2.0 and 2.5 km/h, with seeding operations conducted across two rows. The automated planting system was mounted on the rear frame of the plot seeder and operated in coordination with the seed metering and furrow opening units. The integrated system is explained in Fig. 11. As illustrated in the figure, the automated planting system was installed above the seeding units, functioning synchronously during operation. The interaction between the planting system and the seeding mechanism under actual operating conditions can be inferred from the working configuration shown in Fig. 11b. Seeds belonging to the Yangguang No. 1 variety were used for the field trials, with a Lovol M554-B tractor providing the required power. Preliminary trials were carried out to establish the relationship between the tractor’s gear positions and its forward speed. The main trial was then conducted in the second low gear, and based on the optimal settings identified during the pre-trials, subsequent experiments were conducted. Fig. 11Experimental platform of the automated planting system mounted on the pull-type plot seeder. (a) Side view of the tractor–seeder system; (b) Working configuration during field operation. Experimental platform of the automated planting system mounted on the pull-type plot seeder. (a) Side view of the tractor–seeder system; (b) Working configuration during field operation. Orthogonal optimization experiment Given the lack of national standards for evaluating automated high-capacity planting systems32, the qualification rate of a single container during continuous planting was adopted as the criterion for assessing the performance and stability of the seed delivery technology developed in this study. To examine the impact of the tip angle of the opener (A), the tilt angle of the opener (B), and the pushrod operating speed (C) on planting performance, a 3-factor, 5-level quadratic rotation orthogonal combination experiment was conducted. In total, 23 groups were established. The test followed the guidelines outlined in Testing Methods of Single Seed Drills (Precision Drills) (GB/T 6973–2005) and relevant scholarly research22,33–36, with the three aforementioned factors serving as independent variables. The qualification rate (Y1) was chosen as the corresponding indicator and was calculated using the following formula:21\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Y_{1}=\frac{n_{1}}{N_{1}}\times 100\%$$\end{document} Herein \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Y_{1}$$\end{document}—Qualification rate; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N_{1}$$\end{document}—Total number of seed cartridges tested; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$n_{1}$$\end{document}—Number of qualified seed cartridges. To ensure the clarity and reproducibility of the assessment, a “qualified seed cartridge” was explicitly defined. A seed cartridge was considered qualified only when all the following conditions were simultaneously satisfied: (1) all seeds were completely discharged from the cartridge, without any residue; (2) no missed seeding or blockage occurred during the seed delivery process; (3) the seed flow was continuous and stable, without any interruption; and (4) the seeds were released at their designated positions in accordance with the preset operation sequence. During the experiments, the performance of each seed cartridge was evaluated through direct observation and counting. The total number of qualified seed cartridges was recorded, and the qualification rate was calculated accordingly. In total, 3 cartridges containing 150 seed cartridges each were examined, and each test was repeated three times. The average value of these measurements was taken for analysis. Optimized parameter test To maximize the qualification rate (objective function) given the constraints of various experimental factors (8.18° ≤ A ≤ 41.82°, 23.18° ≤ B ≤ 56.82°, and 55.31 mm/s ≤ C ≤ 111.36 mm/s), multi-objective optimization of the regression equation was performed using Design Expert software. The objective function was as follows:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s.t.\left\{\begin{array}{l}max\,\,Y_{1}\left(x_{1},x_{2},x_{3}\right)\\-1\leq x_{1}\leq 1\\-1\leq x_{2}\leq 1 \\-1\leq x_{3}\leq 1\end{array}\right.$$\end{document} Bench verification test To verify the reliability of the field experiment data, in July 2023, a laboratory bench test was conducted at the Heilongjiang Academy of Agricultural Machinery Engineering. The JPS-12 computer vision seed metering bench was employed to evaluate the planting system. First, upon powering up the host computer, the main interface of the control system was activated, automatically connecting the system with the PLC controller. Once the planting preparation for the plots was complete, the plot length and the number of plots was set, the initial parameters were calibrated, and the planting operation was executed. This planting operation could be controlled either manually or automatically. In the manual control mode, the angle of the opener and pushrod operating speed were manually adjusted to preset values by observing the motion of the seed cartridge and storage cart. These parameters were then added as system inputs. Meanwhile, under the automatic planting control mode, continuous planting was executed thereafter according to the selected parameters. This ensured the flexibility of parameter adjustment and planting stability, providing a reproducible test environment for structural optimization. Field validation The field trial, conducted in August 2023 in an experimental field of the Heilongjiang Academy of Agricultural Machinery Engineering, involved a well-designed experimental setup comprising twelve 8 m2 plots. To minimize experimental errors, a seed delivery tube was connected to the seed discharge port of the planting system, extending 20–30 mm above the ground of the plot. To clearly observe the planting efficiency of the seed cartridge, the soil covering device was not used in any of the three field trials. After the metrics for each trial were recorded, the seeds within the trial area were cleared prior to the subsequent trial. Results and discussion Orthogonal test results Following the principles of Central Composite Design (CCD), a three-factor, five-level orthogonal combination experiment35,37 was designed using Design-Expert 8.0 software. The experimental factors and levels are shown in Table 4. Meanwhile, the experimental scheme and results are shown in Table 5, with x1, x2, and x3 presented as the factor coding values of the tip angle of the opener, tilt angle of the opener, and pushrod operating speed. The range of coding values for each factor is -1.682 to + 1.682, corresponding to the extreme and intermediate values of actual physical quantities. As shown in Table 5, the qualification rate ranges from 95.56% to 99.56%, indicating that different parameter combinations have a significant impact on seed supply performance. Table 4Test factor levels.LevelA: Tip angle of the opener (°)B: Tilt angle of the opener (°)C: Operating speed of the pushrod (mm/s)− 1.6828.1823.1855.31− 1153066.670254083.34+ 135501001.68241.8256.82111.36 Table 4Test factor levels.LevelA: Tip angle of the opener (°)B: Tilt angle of the opener (°)C: Operating speed of the pushrod (mm/s)− 1.6828.1823.1855.31− 1153066.670254083.34+ 135501001.68241.8256.82111.36 Test factor levels. Table 5Results of the orthogonal experiment.Experiment No.Independent variableQualification rate (100%) x 1 x 2 x 3 1− 1− 1− 199.3321− 1− 198.673− 11− 195.56411− 197.565− 1− 1198.8961− 1199.117− 11197.78811199.569− 1.6820097.11101.6820098.22110− 1.682098.001201.682096.671300− 1.68296.8914001.68298.441500096.671600097.111700096.001800097.781900096.442000097.332100096.892200096.222300097.56 Table 5Results of the orthogonal experiment.Experiment No.Independent variableQualification rate (100%) x 1 x 2 x 3 1− 1− 1− 199.3321− 1− 198.673− 11− 195.56411− 197.565− 1− 1198.8961− 1199.117− 11197.78811199.569− 1.6820097.11101.6820098.22110− 1.682098.001201.682096.671300− 1.68296.8914001.68298.441500096.671600097.111700096.001800097.781900096.442000097.332100096.892200096.222300097.56 Results of the orthogonal experiment. Regression analysis and model validation To determine the impact of the three aforementioned factors on the qualification rate, the experimental data were subjected to multiple nonlinear regression analyses. A quadratic polynomial regression equation was established for the qualification rate (Y1). The variance analysis method was adopted, and the results are shown in Table 6. After excluding factors that did not significantly affect the experimental indicators, a factor coding regression equation was established:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned}Y_{1}&=96.87+0.3809x_{1}-0.5710x_{2}+0.5007x_{3}+0.5278x_{1}x_{2}+0.0833x_{1}x_{3}+0.5278x_{2}x_{3}\\ &\quad+0.4221x_{1}^{2}+0.3043x_{2}^{2}+0.4221x_{3}^{2}\end{aligned}$$\end{document} Herein \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Y_{1}$$\end{document}—Qualification index (%); \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$x_{1}$$\end{document}—Coding value of the tip angle of the opener; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$x_{2}$$\end{document}—Coding value of the tilt angle of the opener; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$x_{\mathrm{3}}$$\end{document}—Coding value of the pushrod operating speed. Table 6Analysis of range results.Variance sourceQualification indexSum of squaresDegrees of freedomMean squareF P x 1 1.9811.985.090.0419* x 2 4.4514.4511.440.0049** x 3 3.4213.428.80.0109*x1 x30.055610.05560.14270.7117x2 x32.2312.235.730.0325* x 2 2 1.4711.473.780.0738* x 2 4.4514.4511.440.0049** x 3 3.4213.428.80.0109*x1 x22.2312.235.730.0325*Model21.4192.386.110.0019**Residual5.06130.3892Lack of fit2.150.41931.130.4161Error2.9680.3704Sum26.4722* indicates a significant difference (0.01 < P < 0.05); ** indicates an extremely significant difference (P < 0.01). Table 6Analysis of range results.Variance sourceQualification indexSum of squaresDegrees of freedomMean squareF P x 1 1.9811.985.090.0419* x 2 4.4514.4511.440.0049** x 3 3.4213.428.80.0109*x1 x30.055610.05560.14270.7117x2 x32.2312.235.730.0325* x 2 2 1.4711.473.780.0738* x 2 4.4514.4511.440.0049** x 3 3.4213.428.80.0109*x1 x22.2312.235.730.0325*Model21.4192.386.110.0019**Residual5.06130.3892Lack of fit2.150.41931.130.4161Error2.9680.3704Sum26.4722* indicates a significant difference (0.01 < P < 0.05); ** indicates an extremely significant difference (P < 0.01). Analysis of range results. * indicates a significant difference (0.01 < P < 0.05); ** indicates an extremely significant difference (P < 0.01). Analysis of variance (Table 6) showed that the model was highly significant (P<0.01), and the lack-of-fit indicator F was not significant (P> 0.05), verifying the effectiveness of the equation. Among the different factors, the tilt angle of the opener (x2) had a highly significant effect on the qualification rate (P< 0.01), while the tip angle of the opener (x1), pushrod operating speed (x3), their interaction terms (x1 × 2, x2 × 3), and quadratic terms (x12, x22, x32) also had a considerable effect (P< 0.05 ). Influence of different factors on seeder performance Response surface methodology involves the use of graphical techniques to display the functional relationship between two factors and their response values, allowing us to intuitively observe the relationship between the experimental values and response values of various variables, as well as the types of interactions between the two measured variables. Accordingly, optimal conditions can be selected for experimental design. In this study, based on the regression equation, response surfaces were computed to visualize the interaction effects of the experimental factors on the seed metering qualification rate. These factors included the tip angle and tilt angle of the opener, the operating speed of the pushrod, and the opening position of the seed cartridge, as shown in Fig. 12. The response surface analysis (Fig. 12) further indicated that when the tip angle of the opener tip approached the center value (30°), the tilt angle increased to 46°, and the pushrod operating speed increased to 110 mm/s, the qualification rate tended to peak. This was consistent with the optimization results. Fig. 12Influence of various experimental factors on the cartridge opening qualification rate. (a) Interaction effect of Tip angle and Tilt angle; (b) Tip angle and Pushrod speed; (c) Tip angle and Opening position; (d) Tilt angle and Pushrod speed; (e) Tilt angle and Opening position; (f) Pushrod speed and Opening position. Influence of various experimental factors on the cartridge opening qualification rate. (a) Interaction effect of Tip angle and Tilt angle; (b) Tip angle and Pushrod speed; (c) Tip angle and Opening position; (d) Tilt angle and Pushrod speed; (e) Tilt angle and Opening position; (f) Pushrod speed and Opening position. Figure 12 illustrates the interaction effects of various experimental factors on the cartridge opening qualification rate. As depicted in Fig. 12a, at a pushrod operating speed of 83.34 mm/s and an opening position of 0 mm, the qualification rate remained stable with an increasing tip angle at low tilt angles. However, at high tilt angles, the qualification rate increased as the tip angle of the opener became larger. Meanwhile, at a constant tip angle, the qualification rate rose with an increasing tilt angle. Figure 12b shows that at a tilt angle of 40° for the opener and an opening position of 0 mm, the qualification rate rose with an increase in the tip angle of the opener at low pushrod operating speeds. At high pushrod speeds, the qualification rate decreased as the tip angle of the opener increased. When the tip angle of the opener was constant, the qualification rate rose with increasing pushrod speed. Figure 12c‌ reveals that at a tilt angle of 40° for the opener and a pushrod speed of 83.34 mm/s, the qualification rate initially increased and then decreased as the opening position of the seed cartridge changed, provided that the tip angle remained constant. At low opening positions, the qualification rate rose with an increase in the tip angle of the opener, whereas at high positions, the qualification rate remained relatively stable. Figure 12d demonstrates that, when the tilt angle of the opener remained constant, the tip angle was 25°, and the seed cartridge’s opening position was 0 mm, the qualification rate rose with the pushrod speed. Meanwhile, when the pushrod speed was kept constant, the qualification rate rose with the increase in the tilt angle of the opener. According to Fig. 12e, at an opener tip angle of 25° and a pushrod speed of 83.34 mm/s, the qualification rate declined as the representative value of the opening position increased, particularly at higher tilt angles. Conversely, at low tilt angles, the qualification rate gradually increased as the representative value of the opening position rose. When the opening position was constant, the qualification rate became higher as the tilt angle of the opener increased. Finally, as shown in Fig. 12f, at a 25° and 40° tilt angle for the opener (given a constant pushrod speed), the qualification rate initially increased and then decreased as the opening position decreased. However, when the opening position was kept fixed, the qualification rate improved with increasing pushrod speed. Optimized parameter results \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s.t.\left\{\begin{array}{l}max\,\,Y_{1}\left(x_{1},x_{2},x_{3}\right)\\ -1\leq x_{1}\leq 1\\ -1\leq x_{2}\leq 1\\ -1\leq x_{3}\leq 1\end{array}\right.$$\end{document} The optimal parameter combination obtained from the function was as follows: an opener tip angle of 30°, a tilt angle of 46°, a pushrod operating speed of 110 mm/s, and a seed cartridge opening position of -9 mm. Under these conditions, the theoretical qualification rate of planting from the seed cartridge was 99.59%. To verify the reliability of the optimization data, the optimized parameters were subjected to three rounds of testing (Table 7). The actual average qualification rate was 99.33%, showing a deviation of only 0.26% from the theoretical value, indicating that the optimization model had high applicability. Table 7Performance parameter optimization.Experimental factorActual resultsx1 (°)x2 (°)x3 (mm/s) Y 1 304611099.33 Table 7Performance parameter optimization.Experimental factorActual resultsx1 (°)x2 (°)x3 (mm/s) Y 1 304611099.33 Performance parameter optimization. Bench test results To evaluate the performance of the proposed automated planting system under controlled conditions, a bench test was conducted using a JPS-12 computer vision seed metering test platform. As shown in Fig. 13a, the test platform consisted of a mechanical support structure, a seed cartridge transport mechanism, and a vision-based monitoring system. The automated planting system was mounted on the platform to simulate the seed feeding and opening process. The control interface (Fig. 13b) enabled the real-time monitoring and adjustment of key parameters, including pushrod motion, opener configuration, and system operation status. Before testing, the system was initialized, and key parameters were selected according to the experimental design. The tests were conducted in both the manual and automatic modes. Each test was repeated thrice to ensure reliability. During the test, performance indicators such as seed cartridge operation status, seed delivery continuity, blockage occurrence, and qualification rate were recorded to evaluate system performance. Fig. 13Bench test platform used for the performance verification of the automated planting system. (a) Overall structure of the JPS-12 computer vision seed metering test platform; (b) Control interface and operation console for parameter setting and real-time monitoring. Bench test platform used for the performance verification of the automated planting system. (a) Overall structure of the JPS-12 computer vision seed metering test platform; (b) Control interface and operation console for parameter setting and real-time monitoring. Field validation results The field trial was conducted to validate the optimized combination of the tip and tilt angles of the opener, pushrod operating speed, and opening position of the seed cartridge. This combination was found to yield the best planting performance and operational stability, with the qualification rate of a single cartridge remaining consistently above 99% under continuous planting conditions. This indicated that the structural design of the automated high-capacity planting system for corn plot seeders was reasonable, and that the experimental results of parameter optimization were reliable. Discussion This study presents the design and experimental validation of an automated, high-capacity corn plot seeding system aimed at improving sowing efficiency and accuracy. Through laboratory experiments and field trials, the optimal system parameters, including opener tip angle, opener tilt angle, pushrod operating speed, and seed cartridge opening position, were determined. The optimized parameter combination achieved a seeding qualification rate of 99.33%, demonstrating the system’s effectiveness and applicability under practical conditions. In addition, benchmarking against leading international systems indicated measurable performance improvements4,5,24. For example, the developed system achieved a 1.6–3.0% higher qualification rate than leading commercial systems, while maintaining robust performance under varying field conditions. It reduced manual intervention by 76%, although with slightly longer cycle times (4.5 s vs. 3.2 s for industry gold standards). A key innovation lied in its enhanced adaptability, with approximately 300% greater tolerance to variations in soil hardness without the need for manual recalibration. From an economic perspective, the modular architecture could enable a cost reduction of approximately 77% relative to conventional imported systems, while incorporating advanced sensing capabilities that are not commonly available in existing systems. Although the proposed system demonstrated strong performance under optimized conditions, the field experiments did not include a direct control group (e.g., manual seeding or conventional mechanical systems). This could limit the rigor of comparative assessments. To address this, system performance was compared with results reported in the literature and with data from commercial systems. A comparative analysis with representative international plot seeding systems, such as those developed by Wintersteiger and Almaco, is presented in Table 8. These systems are widely recognized for their high levels of automation and operational efficiency. Compared with these systems, the proposed system achieves comparable or superior seeding qualification rates while significantly reducing manual intervention. Moreover, the integration of a three-stage sensing module enables real-time seed-to-plot verification, a feature not commonly implemented in existing systems. The modular design also enhances adaptability and contributes to overall cost reduction. Table 8Comparison with representative international plot seeding systems.IndicatorThis studyWintersteigerAlmacoSeeding qualification rate99.33%~ 96 to 98%~ 97 to 98%Automation levelHighHighHighSensor integrationYes (3-stage)No/limitedLimitedManual interventionReduced by 76%ModerateModerateAdaptabilityHighMediumMediumCostLowerHighHigh Table 8Comparison with representative international plot seeding systems.IndicatorThis studyWintersteigerAlmacoSeeding qualification rate99.33%~ 96 to 98%~ 97 to 98%Automation levelHighHighHighSensor integrationYes (3-stage)No/limitedLimitedManual interventionReduced by 76%ModerateModerateAdaptabilityHighMediumMediumCostLowerHighHigh Comparison with representative international plot seeding systems. The design and experimental trials presented in this study are of considerable significance for improving the sowing efficiency and accuracy of Chinese corn plot seeders. Currently, many domestic applications still rely on manual methods or basic seed supply equipment, which are characterized by low efficiency, limited precision, high labor intensity, and substantial human resource requirements. To address these limitations, our research institute has developed a high-capacity automated seed supply system capable of supporting various sowing methods and seed types. By integrating technologies such as seed cartridge code recognition, automated dispensing, and cartridge recycling, the system enables continuous, large-scale, and precise seed delivery without operational interruption. Compared with existing devices, which are often hindered by their limited capacity, low reliability, and poor scalability, the proposed system provides a more robust and efficient solution for modernizing seed supply operations in mechanized agriculture. Nevertheless, several potential sources of seed delivery error must be acknowledged. These include occasional seed bridging under high-humidity conditions, seed misplacement due to uneven vibration transmission on rough terrain, and disruptions in seed flow owing to minor deformations in reusable cartridges after extended use. Moreover, seed detection accuracy may degrade over time without the appropriate recalibration of the optical sensors, especially under dusty or low-light field conditions. These technical vulnerabilities highlight the need for robust error-detection mechanisms and redundant sensing strategies in future iterations. Real-world adoption also presents operational challenges beyond those encountered under controlled experimental conditions. For instance, performance consistency on terrains with slopes exceeding 15° or with highly variable soil compaction (e.g., transitions between sandy and clay soils) remains uncertain. Furthermore, maintaining sensor alignment, ensuring cartridge cleanliness, and managing power supply stability in remote environments may limit field adoption without appropriate training and technical support. Maintenance considerations, such as the availability of spare parts, diagnostic tools, and remote calibration support, may further constrain large-scale adoption, particularly in regions with limited agri-tech infrastructure. The scope of this study is also influenced by limitations related to available resources, costs, and time. Although the system yields significant advancements in automated seeding, certain practical constraints remain. First, the field validation was conducted under typical agronomic conditions for corn cultivation; however, the performance under extreme conditions (e.g., heavy clay soils or steep terrain) remains to be evaluated. Second, the mechanical wear observed during extended operation suggests the need for further material optimization for high-friction components. Third, while the sensing system performed reliably under controlled conditions, additional calibration may be required for deployment under variable weather conditions. Moreover, the current design focuses primarily on seed delivery mechanics and does not incorporate post-sowing processes such as soil compaction monitoring, which could be addressed in future studies through integrated agronomic approaches. Future work will focus on both short-term improvements and long-term technological integration from the perspective of practical considerations. In the short term (0–2 years), efforts should be focused on expanding compatibility with different seed types through modular cartridge redesign, validating system performance under challenging field conditions (e.g., slopes > 15° and high-clay soils), and enhancing the durability of high-wear components through accelerated life testing. Over the longer term (3–5 years), development should target closed-loop agronomic systems that integrate real-time soil monitoring with adaptive sowing parameters, incorporate AI-assisted crop monitoring using UAV-based multispectral imaging, and explore blockchain-enabled traceability from sowing to harvest. Conclusions This study describes the development of a sensor-integrated, high-capacity automated planting system for corn plot seeders, addressing key limitations of existing systems in terms of automation, accuracy, and operational efficiency. By combining mechanical optimization with a three-stage sensing mechanism, the proposed system achieves reliable seed delivery and accurate seed–plot matching. The results demonstrate that the integration of sensing and control frameworks significantly enhances system stability and reduces manual intervention, providing a practical solution for improving the efficiency of plot-based breeding operations. Furthermore, the modular architecture facilitates flexible adaptation under varying field conditions and supports the upgrading of existing seeding equipment. Future work will focus on advancing system robustness under complex field environments, expanding compatibility with different crop types, and developing closed-loop intelligent control strategies for adaptive seeding.