An effect of silver arsenic sulfide and gallium sulfide dielectric materials in SPR refractive sensor: a numerical study Authors: Himabindu Thatha, Yesudasu Vasimalla, S. R. Srither, Ravi Sankar Puppala, Santosh Kumar Published: 2026 ABSTRACT In this article, we present a highly sensitive surface plasmon resonance (SPR) sensor to detect the cancer biomarker Carcinoembryonic antigen (CEA). The sensor is designed using the Kretschmann configuration and incorporates an FK51A prism along with layered materials such as silver (Ag), silver arsenic sulfide (Ag3AsS3), and gallium sulfide (GaS) and selected (2D) materials like black phosphorus and Graphene. These 2D materials are chosen for their excellent optical properties and their ability to increase electric field confinement in sensing interfaces. The simulation results show that the proposed multilayer sensor provides considerable improvements in the sensing performances including high sensitivity, sharp resonance curves, and increased figure of merit (FoM). Results confirms that the proposed sensor with WS2 is gained a maximum sensitivity of 350.61°/RIU and an extraordinary quality factor (QF) of 106.650 RIU−1. Compared to existing sensors, this sensor shows better results with a simple construction process. The use of customized 2D materials also improves signal-to-nosie ratio (SNR) of 1.57 and combined sensitivity factor (CSF) of 68.20, which is highly suitable for detecting the initial stage CEA. This task indicates that integrating 2D materials in SPR platforms can greatly extend biosensor technologies for cancer diagnosis. Introduction CEA is a glycoprotein which is mainly concerned with cell adhesion, and is highly produced during the fatal stage. In healthy adults, its serum levels are much lower and very low. Nevertheless, in most cancers, especially colorectal cancer (CRC), the levels of CEA are excessively elevated. As a consequence of this action, CEA is a valuable clinical biomarker that helps in the diagnosis of cancer, monitoring of treatment and the occurrence of recurrence1. The different kinds of 120 tumors, 65 have overexpressed CEA, Colorectal carcinomas and other gastrointestinal cancer have the largest positive rate (98.7%)2. Research suggests that high serum CEA levels are associated with the more advanced stages of the disease and the results of worse survival, especially in colorectal cancer patients who have a remedial affection2. Its interpretation in clinical settings is more complicated by the association of elevated CEA levels with lifestyle variables including drinking and smoking3. The CEA levels should be carefully interpreted in combination with other clinical terms as the utility of protein is not limited to oncology; It can also be raised in benign diseases4. All things are believed to be an important biomarker in the diagnosis of CEA cancer, especially gastrointestinal cancer, clinical oncology4 highlights its importance. SPR Biosensor has made it possible to detect a major biomarker, CEA for many cancers, especially colorectal and ovarian cancer. These biosensors use the unique optical properties of plasmonic materials, such as silver nanoparticles to detect signal. For example, wavy silver alloys are shown to improve the sensitivity to detect Nanoparticle CEA, which acquires 0.55 NG/ML, which is necessary for the first identity5. In addition, by employing Aptamers for selective bonding for CEA, SPR-enhanced total internal reflection Ellipsometry (SPR-Tire) has shown boundaries of low detection, down to 0.1 pg/ml6. In addition, the SPR signal has been enhanced by the inclusion of antibody-quantum dot conjugates, which is able to detect several tumor markers, including the CEA, with a range of 0.1 NG/ML7. SPR has also demonstrated encouraging conclusions in direct detection of CEA autoantibody in serum samples, with good correlations with traditional ELISA techniques8. It has been investigated to improve the sensor accountability in complex biological matrices such as blood plasma by functioning gold nanoparticles with some peptides, so improve CEA detection9. When taken as a whole, these development displays the promise of SPR biosensor in cancer detection. The capacity of the SPR biosensor is one of its main advantages to offer high-sensitivity, real-time, label-free identity10. This preserves the integrity of biological interactions by cutting cost and complexity with the requirement for secondary labelling agents. By measuring variation in the refractory index close to the sensor surface, the SPR method can identify the trace of CEA in complex biological fluids such as blood or serum11. Early-stage cancer is required to improve the patient’s results, which is smooth by this increased sensitivity. In addition, by functioning the surface of the sensor with highly selective antibodies or CEA identification, SPR biosensor provides extraordinary selectivity12. Real-time kinetic analysis in combination with accurate molecular beliefs, by reducing false positivity and false negative, increases clinical accuracy. Besides, the addition of nanomaterials expands the detection range and allows the detection of ultra-cum levels of CEA and the excess of the SPR signal as in the case of gold nanoparticle or graphene13. All things were considered, SPR biosensor enhances the accuracy, speed and sensitivity of the diagnosis of cancer, which open the door for more individual and successful treatment schemes14. The addition of nanomaterials like graphene and silver nanoparticles also strengthening the local electromagnetic field, which boosts the reaction of the signal and thus the detection limit can reach to picomolar levels15. Thanks to these nano structural reforms, SPR is a more reliable tool for clinical diagnosis and the stability and recurrence of the sensor improve as well16. SPR biosensor can also be designed for multiplex detection, which enables the study of multiple cancer biomarkers simultaneously17. It improves clinical value and provides more intensive patient profile. When combined, these benefits m ace SPR biosensor a high sensitivity, quick and scalable platforms to make the initial and reliable detection of the reflexes using the CEA. A SPR sensor in creep Kretschmann setup is the proposed setup to be used in the detection of CEA. Here, a prism is covered by a thin layer of metal (mostly silver that allows the thriving plasmon resonance when excited by polarized light. The advantages of these layered structures include enhanced light-matter interaction, enhanced resonance sharpness and an appropriate surface on which to immobilize biomolecules18. Certain antibodies that are CEA specific are functionalized on the sensing surface so as to bind specifically to the antigen. In the event that the CEA molecules in the sample are bound to the surface with the antibody, the local refractive index will change and this will result in a shift in the resonance angle or wavelength. This change is directly proportional to the concentration of the CEA in the sample, and it allows very sensitive, label-free and real time detection. The suggested design, therefore, is highly sensitive, stable, and with higher figure of merit, and it can be considered a improved sensing performance, in early detection of cancer19. Conventional SPR biosensors based on Ag, graphene, MoS2, BP, and other 2D materials have shown better sensing performance for biomarker detection. Yet, many reported designs rely on just one dielectric layer, or only on a narrow range of plasmonic enhancement methods, which in return limits the confinement of the electric field and also reduces the sensing accuracy. To mitigate these issues, this work suggests a new multilayer SPR sensor. It integrates Ag3AsS3 and GaS dielectric layers, plus TMDC-based 2D materials, targeting ultrasensitive CEA detection. To the best of our knowledge, the joint use of Ag3AsS3 and GaS layers in SPR biosensors for cancer biomarker sensing has not been reported before. Overall, the proposed configuration improves optical confinement, strengthens plasmon coupling, and enhances biomolecule interaction, leading to a notably better sensitivity as well as a higher quality factor.20. Design consideration and methodology This step develops the equation of the significant design parameters necessary in the sensor correction and it also presents the mathematical modelling framework adopted to analyse the intensity of sensor reflection. It gives a quantitative foundation on which to analyse the efficacy and credibility of the sensor, and determine the specifications of large sensory functions. Design considerations The Kretschmann configuration, which minimizes the Kerr effect and enhances optical coupling, is utilized in the design of the proposed sensor for CEA detection. For performance measurements at a wavelength of 633 nm, a FK51A prism with Refractive Index (RI) of 1.4853 is used as the initial layer to allow efficient light coupling21. The use of a lower RI prism can further enhance the sensor’s sensitivity. Ag is employed as the second layer RI of 0.056206 + 4.27761i to excite surface plasmon polaritons (SPPs) and optimize the plasmonic response22. To further enhance sensitivity and increase the interaction length of the plasmon wave, a Ag3AsS3 layer RI of 2.6720 is introduced21. Following this, a GaS layer RI of 2.5897 is included as a high-index dielectric material to spatially separate the metal and 2D material layers. This configuration optimizes SPR by maintaining the electric field energy and reducing excessive damping. A layer of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${HfSe}_{2}$$\end{document} with a RI of 4.1258 + 0.027875i is then deposited above GaS to further enhance the sensor’s sensitivity23. On top of these layers, the 2D material configuration is introduced, including BP RI of 3.5 + 0.01i graphene RI of 3 + 1.1487i, WS2 RI of 4.9 + 0.3124i, MoS2 RI of 5.08 + 1.1723i, MoSe2 RI of 4.62 + 1.0063i, and WSe2 RI of 4.55 + 0.4332i. The sensor performance is evaluated using various ambient media, each with different RI values: 1.330024, 1.33007, 1.3374, 1.3411, 1.3448, and 1.3485. This carefully designed multilayer stack enables precise tuning of SPR conditions, resulting in high sensitivity and improved detection capabilities for CEA. When the propagation constant of the p-polarized incident light (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{x}$$\end{document}) the propagation constant of the surface plasmon wave (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{SPW}$$\end{document}). This resonance condition, commonly referred to as the SPR condition, is mathematically described by Eqs. (1) and (2), which define the criteria for plasmon excitation and field enhancement at the metal–dielectric interface. The proposed Kretschmann configuration based SPR sensor structure is shown in Fig. 1. This is the p-polarized configuration where light is incident on the FK51A prism and then onto a thin layer of silver (Ag) and surface plasmon waves are excited at the silver–dielectric interface. The Ag film is coated with extra layers of Ag3AsS3, GaS and HfSe2 to improve the performance of the sensor. These layers of dielectric material and 2D material help in enhancing the optical confinement, the enhancement of the electric field, and the interaction between the plasmonic field and the analyte molecules. The multilayer structure is topped with the layer of analytes (CEA). The incident light energy resonates with surface plasmons at a specific angle, causing the reflected light intensity to greatly decrease. A change in the RI of the analyte results in a change in the resonance angle. The right side of the figure depicts the resonance dip variation as a function of the different refractive indices of the analytes, which is the sensing mechanism of the proposed SPR biosensor.1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{x}={\mathrm{k}}_{\mathrm{S}\mathrm{P}\mathrm{W}}$$\end{document}2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{k}}_{0}{\mathrm{n}}_{\mathrm{p}}\mathrm{sin}{\uptheta}_{\mathrm{r}\mathrm{e}\mathrm{s} }={\mathrm{k}}_{0}\sqrt{\frac{{\upepsilon}_{\mathrm{m}}{\mathrm{n}}_{\mathrm{d}}^{2}}{{\upepsilon}_{\mathrm{m}}+{\mathrm{n}}_{\mathrm{d}}^{2}}}$$\end{document}where is the free space propagation constant, is the dielectric layer’s RI, prism’s RI, a contact with the metallic layer and finally SPR angle of resonance. Equation (2) reveals that under resonance conditions, the incident light energy absorbance in sensors is maximized so that the reflectance on the detector side () minimized. Mathematically, this scenario is represented by Eq. (3). Here, and represent the RI values of prism, metal, and dielectric layer respectively.Fig. 1Block diagram of the proposed sensors of CEA detection.3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{SPR}=\left({\mathit{sin}}^{-1}\sqrt{\frac{{r}_{m}^{2}{r}_{d}^{2}}{{r}_{p}^{2}\left({r}_{m}^{2}+{r}_{d}^{2}\right)}}\right)$$\end{document} Block diagram of the proposed sensors of CEA detection. Left as a function of the normalized layer thickness Written by Laurent The following equations allow you to calculate reflectivity and its corresponding coefficient() Eqs. (4) and (5) which are very important for studying the optical response of sensors. Similarly, Eqs. (6) to (10) define the terms used in these Eqs. (4) and (5), respectively. Here transvers RI of layer, noted as, can be expressed with Eq. (6). In addition, the "characteristic matrix of the integrated sensor structure" for p-polarized incident light was described in Eq. (7) serves a crucial role in the interaction of light with this multilayer structure.4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${F}_{p}={f}_{p}{f}_{p}^{*}={\left|{f}_{p}\right|}^{2}$$\end{document}5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${f}_{p}=\frac{\left({F}_{11}+{F}_{12}{b}_{x}\right){b}_{1}-\left({F}_{21}+{F}_{22}{b}_{x}\right)}{\left({F}_{11}+{F}_{12}{b}_{x}\right){b}_{1}+\left({F}_{21}+{F}_{22}{b}_{x}\right)}$$\end{document}6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${b}_{x}=\sqrt{\frac{{\mu}_{x}}{{\varepsilon}_{x}}}\mathit{cos}{\theta}_{x} =\sqrt{\frac{{\varepsilon}_{x}-{\left({r}_{p}\mathit{sin}\theta \right)}^{2}}{{\varepsilon}_{x}^{2}}}$$\end{document}7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${F}_{if}={\left[\prod_{x=2}^{N-1}\left(\begin{array}{c}\mathit{cos}{\beta}_{x} \frac{i}{{b}_{x}}\mathit{sin}{\beta}_{x}\\ i{b}_{x}\mathit{sin}{\beta}_{x} \mathit{cos}{\beta}_{x}\end{array}\right)\right]}_{if}= \left[\begin{array}{c}{F}_{11} {F}_{12}\\ {F}_{21} {F}_{22}\end{array}\right]$$\end{document} Furthermore, Eq. (8) express \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\beta}_{x}$$\end{document} as the free arbitrary phase constant of the \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${X}^{th}$$\end{document} layer. Equations (9) and (10) provide values for the input angle (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{x}$$\end{document}) and wave impedance (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${s}_{x}$$\end{document}) features at the \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${X}^{th}$$\end{document} layer, respectively. Additionally, Permeability (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mu}_{x}$$\end{document}), permittivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varepsilon}_{x}$$\end{document}), and thickness (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${d}_{x}$$\end{document}) of the layer are crucial factors that define its optical and electromagnetic properties, thereby influencing the behaviour of wave transmission and reflection in the multilayer sensor.8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\beta}_{x}=\frac{2\pi }{\lambda }{n}_{x}{d}_{x}\mathit{cos}{\theta}_{x}$$\end{document}9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{x}={\mathit{sin}}^{-1}\left(\frac{{n}_{p}}{{n}_{x}}\mathit{sin}{\theta}_{inc}\right)$$\end{document}10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${s}_{x}=\frac{{n}_{x}\mathit{cos}{\theta}_{x}}{\left({\eta}_{0}\right)}$$\end{document} Finally, Eq. the reflectivity formula for the proposed six-layer sensor structure is given by (11), where the previous mathematical relationships are incorporated in. In this equation, f12, f23……fn are the reflectivity in between their matching layers. Thickness (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${d}_{x}$$\end{document}) and wave vector factor (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${w}_{x}$$\end{document}) of each layer are important parameters. They influence the way light refracts through the sensor, and they are a significant set of vectors for setting up resonance conditions.11\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${F}_{123456}={\left|{f}_{12\dots ..n}\right|}^{2}={\left|\frac{{f}_{12}+{f}_{2\dots ..n }{e}^{2i{w}_{2}{d}_{2}}}{1+{f}_{12 }{f}_{2\dots .n}{ e}^{2i{w}_{2}{d}_{2}}}\right|}^{2}$$\end{document}We investigate sensitivity, QF, FoM and CSF of the sensor. Expression (7) of these sensing parameters is given by Eqs. (11–14). Where, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla\uptheta }_{res}$$\end{document},, ∇n, FWHM, Rmax and Rmin are the deviation in the SPR resonance angle, RI deviation of the analytes, Full-Width at half-maxima, maximum and minimum reflectance of the SPR curve, respectively. FWHM represents the 50% reflectance amplitude of the SPR spectrum. Its metric, in turn, indicates the detection ability of the sensor, its quality, its resolution, as well as its performance quality, in that order.12\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Sensitivity = Change \, in \, res. \, Angle/Change \, in\;{\mathrm{RI}}$$\end{document}13QF=Sensitivity/FWHM14\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$FoM=Sensitivity/{R}_{min}$$\end{document}15\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$CSF=Sensitivity\times [({R}_{max}-{R}_{min})/FWHM]$$\end{document} Results and discussion Here, we present the simulation results of the designed sensor by use of angular interrogation technique. Analysis is done by plotting the SPR reflectance curve against the incident angle at a constant wavelength of 633 nm. The performance of the proposed sensor is then determined after optimization of each layer thickness. To determine biomolecule detection, the modified multilayer structure will be experimented at varying concentrations of the analyte to establish the correct detection. As well, distribution of the electric field and certain design approaches adopted in the creation of the sensor are analysed. Lastly, the results of the suggested sensor are compared to the current literature to demonstrate the benefits and enhancements. Optimization and influence of proposed structure with Ag3AsS3/GaS In this subsection, we discuss about the optimization of the Ag layer thickness of layers as soon as the thickness of the metal film varies depending on the dying layer that is applied to it. In addition, we are assessing the effectiveness of alternative topology that consider the impact of suggested sensors and indicated layers. The sensor can be adjusted to a series of Ag thickness, including 40, 42, 44, 46, 48, 50, 52, 54 and 56 nm. The thickness of the Ag layer is fixed at 54 nm. This specific thickness was chosen because it provides a low Rmin value, which is crucial for enhancing the performance of the SPR sensor. A lower Rmin indicates a stronger resonance dip, which improves the detection capability of the sensor. The dimension is reflected in the event to show the relationship to the perspective for different Ag thickness. The reflectance spectra of different thicknesses of Ag layer for analyte with n = 1.3300 and n = 1.3485 are shown in Fig. 2a and b, respectively. As the thickness (t) of Ag is increased, it can be seen that the resonance angle shifts and the sensing response gets better. As shown in Table 1, the values of sensitivities gradually rise with the increase of Ag thickness and the maximum is 304.22°/RIU at 56 nm. But sensitivity is not enough to determine the optimum performance of the sensor.Fig. 2The reflection at various angles according to the thickness of the Ag layer differs with the incident angle and Ag3AsS3 = 3 nm, GaS = 3 nm.Table 1Measured parameters using FK51A/Ag/ Ag3AsS3/ GaS/ HfSe2/Analyte.Analyte (∇ n=0.0485)Ag thickness (nm)Ag3AsS3 = 3 nm, GaS = 3 nm404244464850525456Res. Angle1.330077.724777.788877.916978.04578.109178.173278.301378.365478.36541.348582.081182.401482.721782.97883.234283.490583.682783.874984.003Rmin1.33000.316120.241470.17130.109430.059070.0234510.00387240.00182830.0166841.34850.223450.144110.0777880.0298380.00403910.00233110.0233860.0650250.12227Rmax1.33000.98390.98450.98520.98610.98700.98800.98890.98980.99071.34850.97940.97870.97800.97730.97670.97620.97570.97530.9749FWHM1.33002.66652.87252.94262.92282.84182.71772.56432.39032.20321.34853.81134.01424.08144.04793.93643.76213.53643.26712.9583Change in res. angle1.33004.35644.61264.80484.9335.12515.31735.38145.50955.63761.3485Sensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})1.3300235.481249.3297259.718266.648277.032287.42290.33297.81304.221.3485QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})1.330088.3186.8088.2691.2397.48105.76113.22124.59138.081.3485SNR (DA)1.33001.631.611.631.691.801.962.102.302.561.3485FoM1.330060.393465.840473.141181.246791.7219103.2798112.7816124.3622135.77631.3485CSF1.330058.9764.5071.8379.9890.45102.01111.52123.09134.49 The reflection at various angles according to the thickness of the Ag layer differs with the incident angle and Ag3AsS3 = 3 nm, GaS = 3 nm. Table 1Measured parameters using FK51A/Ag/ Ag3AsS3/ GaS/ HfSe2/Analyte.Analyte (∇ n=0.0485)Ag thickness (nm)Ag3AsS3 = 3 nm, GaS = 3 nm404244464850525456Res. Angle1.330077.724777.788877.916978.04578.109178.173278.301378.365478.36541.348582.081182.401482.721782.97883.234283.490583.682783.874984.003Rmin1.33000.316120.241470.17130.109430.059070.0234510.00387240.00182830.0166841.34850.223450.144110.0777880.0298380.00403910.00233110.0233860.0650250.12227Rmax1.33000.98390.98450.98520.98610.98700.98800.98890.98980.99071.34850.97940.97870.97800.97730.97670.97620.97570.97530.9749FWHM1.33002.66652.87252.94262.92282.84182.71772.56432.39032.20321.34853.81134.01424.08144.04793.93643.76213.53643.26712.9583Change in res. angle1.33004.35644.61264.80484.9335.12515.31735.38145.50955.63761.3485Sensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})1.3300235.481249.3297259.718266.648277.032287.42290.33297.81304.221.3485QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})1.330088.3186.8088.2691.2397.48105.76113.22124.59138.081.3485SNR (DA)1.33001.631.611.631.691.801.962.102.302.561.3485FoM1.330060.393465.840473.141181.246791.7219103.2798112.7816124.3622135.77631.3485CSF1.330058.9764.5071.8379.9890.45102.01111.52123.09134.49 Measured parameters using FK51A/Ag/ Ag3AsS3/ GaS/ HfSe2/Analyte. The 54 nm Ag layer shows the optimum overall sensing properties over all thickness considered. The reflectance minimum (R_min) is very small at such thickness which suggests deep surface plasmon excitation and a deeper resonance dip. Furthermore, the sensor has a high quality factor (124.59) and signal to noise ratio (SNR 2.30) for more accurate and reliable detection. The resonance curve at 54 nm is deeper and better defined, highlighting the advantages of better detection precision and measurement stability, although the FoM and CSF are slightly larger at this resonance. Hence, for the proposed SPR sensor, the optimal value of Ag thickness is chosen as 54 nm, due to the combination of its low R_min, high sensitivity, narrow FWHM and the resonance sharpness. Effect of proposed structure This sub-section highlights the effectiveness of the proposed multipurpose structure by comparing its performance with several other configurations made of specific layered materials. Comparison structures are defined as follows: Structure 1 (S1): FK51A Prism/AG (54 Nm)/Analysis, Structure 2 (S2): FK51A Prism/AG (54 Nm)/AG (54 Nm)/Analyte, Structure 3 (S3): FK51a Prism/AG (54 Nm), 3 (54 Nm)/AG (54 Nm)/Gas (3 Nm)/Analysis, and Structure 5 (S5): FK51A Prism/AG (54 Nm)/Ag3AsS3 (3 Nm)/Gas (3 Nm)/Gas (3 Nm)/HFSE2/Analysis. Figure 3 illustrates the variation in reflectance intensity as a function of the incident angle for all considered structures. Figure 3a and b show the reflectance curves before and after analyte adsorption, respectively. For this study, the thicknesses of the layers are optimized as follows 54 nm for Ag, 3 nm for Ag3AsS3, 3 nm for GaS, and 1 nm for HfSe2. The progressive addition of these functional layers results in enhanced surface plasmon resonance characteristics, such as sharper resonance dips, improved sensitivity, and better performance in analyte detection. Table 2 represent the five separate SPR sensor structures (S1) through S1 are compared in the table according to significant performance matrix, in which Rmin. A specific biosensing environment is represented by the refractive index 1.3300 and 1.3485, which mimics the reaction of the sensor after the analysis. The lowest reflection of structure 1 (S1) is 0.004938 at RI of 1.34855 with FK51A Prism and AG (54 nm) with FK51A prism and AG (54 nm). With the sensitivity of 141.978°/RIU, the same resonance angle varies from 70.4214° to 73.048°.This serves as a reference for evaluating the impact of introducing additional layers (S2). Adding a HfSe2 layer enhances field interaction and shifts the resonance angle more than S1. This results in improved sensitivity of 148.902°/RIU (S3). Introducing a 3 nm Ag3AsS3 layer improves light confinement and sharpens the resonance dip. It increases sensitivity to 169.681°/RIU. (S4) A 3 nm GaS layer further boosts plasmon coupling, achieving the same sensitivity as S3. It offers better signal quality with lower reflectance. (S5) Combining Ag3AsS3, GaS, and HfSe2 forms a powerful multilayer structure. It delivers the highest sensitivity of 297.810°/RIU, ideal for ultra-sensitive detection.Fig. 3Reflectance measurement varies with incidence angle for different structures (a) different structures with analyte 1.3300 and (b) different structures with analyte 1.3485.Table 2For different parameters and structures.StructureRminRes angle at 1.3300Res angle at 1.3485Change in Res angleSensitivity1.33001.3485S10.0049380.004839270.421473.0482.6266141.978S20.00301360.001159871.062173.81682.7547148.902S30.00265070.001900472.98476.12313.1391169.681S40.00306670.00049472.855975.9953.1391169.681S50.00182830.06502578.365483.87495.5095297.810 Reflectance measurement varies with incidence angle for different structures (a) different structures with analyte 1.3300 and (b) different structures with analyte 1.3485. Table 2For different parameters and structures.StructureRminRes angle at 1.3300Res angle at 1.3485Change in Res angleSensitivity1.33001.3485S10.0049380.004839270.421473.0482.6266141.978S20.00301360.001159871.062173.81682.7547148.902S30.00265070.001900472.98476.12313.1391169.681S40.00306670.00049472.855975.9953.1391169.681S50.00182830.06502578.365483.87495.5095297.810 For different parameters and structures. Detection process This section focuses on using various 2D materials to detect CEA in blood samples once in separate concentrations. Layers of Ag(54 nm), Ag3AsS3 (3 nm)/ GaS (3 nm), and Hfse2 include sensor design. BP, Hfse2, Graphene, Mos2, WS2, WSe2, and Mose2 are 2D materials used in this study. We was chosen remarkable optical and electrical characteristics, which greatly improve the performance of the sensor. The number of performance criteria, such as sensitivity, QF, FOM, SNR, and CSF, is examined to determine the best setup for detection. Tracking adjustments in resonance perspective that fits version within the RI of the sensing surroundings, how sensitivity is calculated; Large angular shifts indicate excessive detection sensitivity.For numerous CEA concentrations, The reflectance curves versus angle of incidence for different values of the RI of the analytes (n = 1.3300 to 1.3485) are shown in Fig. 4. The resonance dip shifts towards higher incident angles as the RI increases, which shows the sensing response of the proposed SPR sensor. The reflectance characteristics for the different 2D materials are shown separately in subfigures (a)–(g): HfSe2, BP, Graphene, MoS2, MoSe2, WS2, and WSe2, respectively. The graphs clearly show the different resonance behavior of each 2D material, which is attributed to different optical properties and light–matter interaction. It is clear from all the materials considered that among all these materials, WS2 exhibits the more pronounced resonance dip and the maximum shift in resonance angle, thereby demonstrating better sensing performance and higher sensing sensitivity.Fig. 4Incident angle vs Reflectance angle for different 2d materials (a) HfSe2 (b) BP (c) Graphene (d) Mos2 (e) MoSe2 (f) Ws2 (g) Wse2. Incident angle vs Reflectance angle for different 2d materials (a) HfSe2 (b) BP (c) Graphene (d) Mos2 (e) MoSe2 (f) Ws2 (g) Wse2. Table 3 shows the sensor’s reaction to the separate CEA concentrations that is through variation in detection of the medium RI. The resonance grows from 1.3300 to 1.3485 with RI, the resonance, suggests that the sensor may more clearly detect the presence of the CEA. The resonance angle remains stable for highly modest RI variations (such as 1.3300 to 1.33007), so the sensor is unable to take such a minute variation. But the resonance angle changes dramatically because RI increases to more (1.3374, 1.3411, etc.). This indicates that as the CEA concentrations increase, the sensitivity of the sensor increases. But the width of the resonance curve FWHM also increases.Table 3FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)-HfSe2(0.53 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.00182830.989878.36542.3903––1.330070.00137260.989878.36542.39240.0000701.33740.00757090.984480.15922.65670.00741.79381.34110.0149480.978581.24822.81690.01112.88281.34480.030790.975382.46553.01820.01484.10011.34850.0650250.975383.87493.26710.01855.5095 Table 3FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)-HfSe2(0.53 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.00182830.989878.36542.3903––1.330070.00137260.989878.36542.39240.0000701.33740.00757090.984480.15922.65670.00741.79381.34110.0149480.978581.24822.81690.01112.88281.34480.030790.975382.46553.01820.01484.10011.34850.0650250.975383.87493.26710.01855.5095 FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)-HfSe2(0.53 nm)-SM. The performance characteristics of the suggested sensor are reported in Table 4. As the RI increased from 1.3300 to 1.3485, the sensitivity and QF of the HfSe2 based 2D material sensor were determined to be 297.81°/RIU and 91.787 \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{R}\mathrm{I}\mathrm{U}}^{-1}$$\end{document}, the highest sensitivity was attained at RI of 1.3485, which indicates a sharper and better-defined resonance signal, where the small changes in CEA concentration led to detection, QF, which measures the strapless pf the resonance curve, is the biggest 91.787 \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{R}\mathrm{I}\mathrm{U}}^{-1}$$\end{document}. The remaining parameters are noted in Table 4, the potential of the HfSe2 based 2D materials for the CEA detection that is dependable and high performance is indicated by the high sensitivity and rising QF.Table 4FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)-HfSe2 (0.53 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.3374242.4191.2430.67590.55289.1281.3411259.7192.1971.02390.81988.8371.3448277.0391.7871.35888.96186.6941.3485297.81091.15448281.686357985.22716282.975646 Table 4FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)-HfSe2 (0.53 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.3374242.4191.2430.67590.55289.1281.3411259.7192.1971.02390.81988.8371.3448277.0391.7871.35888.96186.6941.3485297.81091.15448281.686357985.22716282.975646 FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)-HfSe2 (0.53 nm)-SM. Table 5 demonstrate that basic obtained for BP based SPR senor is used as the 2D material to detect CEA. The resonance turns from 77.981° to 83.1702° when RI increases from 1.3300 to 1.3485. As the sensitivity increases, changes in the angle gently increase and reach a maximum of 5.1892°. However, as the concentration increases, the signal becomes less intense because FWHM (peak width) becomes wider from 2.2706 to 3.0688 meaning the resonance peak becomes broader at higher RI, slightly affecting the sharpness of the signal.Table 5FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)-BP (0.53 nm)-SM.SM’s RIRminRmax\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.000802320.990877.9812.27061.330070.000370770.990877.9812.27280.0000701.33740.0040910.986679.71072.51760.00741.72971.34110.00878630.982480.73572.66650.01112.75471.34480.0192110.975481.88892.8380.01483.90791.34850.0413530.975483.17023.06880.01855.1892 Table 5FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)-BP (0.53 nm)-SM.SM’s RIRminRmax\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.000802320.990877.9812.27061.330070.000370770.990877.9812.27280.0000701.33740.0040910.986679.71072.51760.00741.72971.34110.00878630.982480.73572.66650.01112.75471.34480.0192110.975481.88892.8380.01483.90791.34850.0413530.975483.17023.06880.01855.1892 FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)-BP (0.53 nm)-SM. The functional parameters of the proposed sensor are presented in Table 6. At low RI values (1.3300 and 1.33007), the sensor shows no average reaction. As RI increases, sensitivity increases from 233.74 to 280.5°/RIU, showing a strong detection for high CEA concentrations. QF high 93 does not fall slightly up to 91.4 at the highest RI. The SNR also continuously improves from 0.687 to 1.69, which reflects clear signals. While the FOM and CSF shows slight cuts, their values are strong, confirm effective sensing performance.Table 6FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)-BP(0.53 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.3374233.7492.84367780.687043292.46385491.2197491.3411248.1793.07000611.033077092.25226590.6142331.3448264.0593.03992151.376990891.25253188.9637491.3485280.591.40292531.690954187.62314085.374628 Table 6FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)-BP(0.53 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.3374233.7492.84367780.687043292.46385491.2197491.3411248.1793.07000611.033077092.25226590.6142331.3448264.0593.03992151.376990891.25253188.9637491.3485280.591.40292531.690954187.62314085.374628 FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)-BP(0.53 nm)-SM. In Table 7 shows the resonance angle gradually moves from 77.2763° to 82.017° because RI increases from 1.3300 to 1.3485. Increasing sensitivity of sensors for increased analysis concentrations is reflected in this angular displacement. First, the shift is negligible on RI of 1.33007, suggesting that the sensor is unable to take the smallest RI changes. The shift, which holds the peak at 4.7407°, becomes more noticeable with major changes in RI. Additionally, FWHM increases from 2.6136 to 3.2398, indicating that while the sensor becomes more responsible, the acuity of resonance peaks decreases to some extent.Table 7FK51A-Ag-Ag3AsS3 (3 nm)-GaS(3 nm)- Graphene(0.34 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.0598110.989777.27632.61361.330070.0599320.989777.27632.61570.0000701.33740.0775780.985578.94192.84120.00741.66561.34110.0915730.981779.83882.96590.01112.56251.34480.111210.975480.86393.09160.01483.58761.34850.140840.974382.0173.23980.01854.7407 Table 7FK51A-Ag-Ag3AsS3 (3 nm)-GaS(3 nm)- Graphene(0.34 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.0598110.989777.27632.61361.330070.0599320.989777.27632.61570.0000701.33740.0775780.985578.94192.84120.00741.66561.34110.0915730.981779.83882.96590.01112.56251.34480.111210.975480.86393.09160.01483.58761.34850.140840.974382.0173.23980.01854.7407 FK51A-Ag-Ag3AsS3 (3 nm)-GaS(3 nm)- Graphene(0.34 nm)-SM. The graphene as 2D material is summarized in this Table 8. The sensor does not display any detection activity when RI is low. The sensitivity gradually increases from Ri of 1.3374 to RI of 1.3485, when it reaches 256.25°/RIU. This value indicates effective identity, even if it is slightly low compared to BP or HfSe2 structures. Standing sensor sharpness is shown by the QF, which remains stable at 79. Although they are often lower than other 2D materials, the SNR and FOM improves as RI development. In comparison, at high analysis levels, the CSF gradually decreases from 71.92 to 65.92, indicating a slight decline in the visual clarity of detection.Table 8FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- Graphene(0.34 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.3374225.0879.22042840.586231173.07466671.9259691.3411230.8677.83669570.863987370.70895669.2845441.3448242.4178.40775181.160434769.68802567.7591951.3485256.2579.09563991.463269367.9558165.923052 Table 8FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- Graphene(0.34 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.3374225.0879.22042840.586231173.07466671.9259691.3411230.8677.83669570.863987370.70895669.2845441.3448242.4178.40775181.160434769.68802567.7591951.3485256.2579.09563991.463269367.9558165.923052 FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- Graphene(0.34 nm)-SM. Table 9 shows, the SPR sensor detects CEA the use of Mos2 as 2D material. The resonance attitude (θres) particularly modifications from 79.52° to 84.964° when the RI increases from 1.3300 to 1.3485, indicating that the sensor CEA reacts properly to a growth in concentrations. More light is absorbed during resonance, which helps in sensing, as seen through the bottom mirrored image Rmin, which is similarly improved from 0.2711 to 0.5353. FWHM, moves up and downs, however stays in large part stable, indicating that the sharpness of the signal is basically preserved.Table 9FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)- MoS2 (0.62 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.271170.974379.51853.4278––1.330070.271550.974379.51853.42880.0000701.33740.327370.974281.50453.41590.00741.9861.34110.372680.974182.65773.16640.01113.13921.34480.438490.974083.81082.290.01484.29231.34850.535340.974084.9643.42880.01855.4455 Table 9FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)- MoS2 (0.62 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.271170.974379.51853.4278––1.330070.271550.974379.51853.42880.0000701.33740.327370.974281.50453.41590.00741.9861.34110.372680.974182.65773.16640.01113.13921.34480.438490.974083.81082.290.01484.29231.34850.535340.974084.9643.42880.01855.4455 FK51A-Ag- Ag3AsS3(3 nm)-GaS(3 nm)- MoS2 (0.62 nm)-SM. This Table 10 shows how the sensor with MoS2 performs for detecting CEA. When RI is very low (1.3300 and 1.33007), the sensor doesn’t respond. As RI increases, the sensitivity goes up from 268.38 to 294.35, showing good detection. The QF peaks at 126.64 for RI of 1.3448, meaning a sharper signal. The SNR also improves, highest at 1.87, and FoM and CSF reach 71.11 and 67.82 at the same RI. At the highest RI (1.3485), these values drop a bit, but sensitivity remains strong. Overall, MoS2 gives a fast and clear response for higher CEA levels.Table 10FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- MoS2 (0.62 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.3374268.3878.5673990.581398752.84678950.8197501.3411282.8189.31619850.991409856.02983753.7165481.3448290.02126.6464061.874366871.11322367.8204171.3485294.3585.7441.58839.84137.612463 Table 10FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- MoS2 (0.62 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.3374268.3878.5673990.581398752.84678950.8197501.3411282.8189.31619850.991409856.02983753.7165481.3448290.02126.6464061.874366871.11322367.8204171.3485294.3585.7441.58839.84137.612463 FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- MoS2 (0.62 nm)-SM. The sensing structure with MoSe2 as 2D material has good detection performances for CEA under the RI ranging from 1.3300 to 1.3485. Initially, upon the small modification of RI from 1.3300 to 1.33007, the resonance angle does not shift, and it signifies the lack of capability to successfully catch very tiny alteration for the sensor. However, with increasing RI, the resonance angle shifts from 79.3263° to 84.8999°, and the angle change (∇θ res) is as high as 5.5736°, demonstrating a high sensitivity. The Rmin shifts from 0.22922 to 0.48243 with higher analyte levels, which corresponds to the improved absorptivity of light, where Rmax remains unchanged. The FWHM is reduced from ∼3.4 to 0.72, thus the resonant peak is sharpened more at higher RI for higher precision (Table 11).Table 11FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- MoSe2 (0.70 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.229220.975779.32633.4031––1.330070.229560.975679.32633.40430.0000701.33740.281170.974281.31233.5110.00741.9861.34110.323440.974182.40143.42820.01113.07511.34480.386050.974183.68272.99920.01484.35641.34850.482430.974084.89990.720670.01855.5736 Table 11FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- MoSe2 (0.70 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.229220.975779.32633.4031––1.330070.229560.975679.32633.40430.0000701.33740.281170.974281.31233.5110.00741.9861.34110.323440.974182.40143.42820.01113.07511.34480.386050.974183.68272.99920.01484.35641.34850.482430.974084.89990.720670.01855.5736 FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- MoSe2 (0.70 nm)-SM. As shown in Table 12, the sensitivity of the sensor was gradually enhanced from 268.38 to 301.28, which demonstrates its intensive response to the CEA level. All the performance values have a certain maximum value at RI = 1.3485. The QF 418.04, the SNR 7.73, and the FoM and CSF achieve 216.36 and 205.50, respectively. The MoSe2 provides not only high sensitivity, but also very sharp and precise signals with high contrast and resolution. Making MoSe2 one of the most sensitive materials in this sensor structure for the effective detection of CEA.Table 12FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- MoSe2 (0.70 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.3374268.3876.43929890.565650854.94686152.9747271.3411277.0480.81093170.897001354.67344352.5804401.3448294.3598.14328871.452520660.25507257.7131601.3485301.28418.049427.7339142216.36983205.50055 Table 12FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- MoSe2 (0.70 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.3374268.3876.43929890.565650854.94686152.9747271.3411277.0480.81093170.897001354.67344352.5804401.3448294.3598.14328871.452520660.25507257.7131601.3485301.28418.049427.7339142216.36983205.50055 FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- MoSe2 (0.70 nm)-SM. Table 13 shows the sensor’s capacity to detect changes is displayed by resonant angle that increases from 80.35° to 86.69° because the RI of sensing medium increases from 1.3300 to 1.3485. sensitivity increases RI 1.3374 increased from 303 to 350.61°/RIU at RI 1.3448. This indicates that minor changes in RI by the sensor can also be detected. Additionally, quality factor (QF) increases with RI, which increases from 81.54 to 1.34448 to a high value of 106.65 at 1.3374, showing that the sensor provides a sign that is clear and faster. The sensitivity is 342.83°/RIU and QF Ri is 100.79 on 1.3485, which is still very good.Table 13FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- WS2 (0.8 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.0908310.975380.35143.39061.330070.0911990.975180.35143.3930.0000701.33740.150850.974682.59363.71580.00742.24221.34110.213260.974684.0033.7840.01113.65161.34480.334950.974585.54053.28750.01485.18911.34850.567980.974586.69373.3930.01856.3423 Table 13FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- WS2 (0.8 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.0908310.975380.35143.39061.330070.0911990.975180.35143.3930.0000701.33740.150850.974682.59363.71580.00742.24221.34110.213260.974684.0033.7840.01113.65161.34480.334950.974585.54053.28750.01485.18911.34850.567980.974586.69373.3930.01856.3423 FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- WS2 (0.8 nm)-SM. Here Table 14 representing the sensitivity increases, RI 1.3374 increased from 303 to 350.61°/RIU at RI 1.3448. This indicates that minor changes in RI by the sensor can also be detected. Additionally, quality factor (QF) increases with RI, which increases from 81.54 to 1.34448 to a high value of 106.65 at 1.3374, showing that the sensor provides a sign that is clear and faster. The sensitivity is 342.83°/RIU and QF Ri is 100.79 on 1.3485, which is still very good.Table 14FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- WS2 (0.8 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.337430381.54367830.603423269.24281467.1716051.3411328.9786.93788930.965010568.39751566.1892921.3448350.61106.6509091.578433470.92818768.2085891.3485342.83100.7951.86943.54540.9751 Table 14FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- WS2 (0.8 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /RIU$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.337430381.54367830.603423269.24281467.1716051.3411328.9786.93788930.965010568.39751566.1892921.3448350.61106.6509091.578433470.92818768.2085891.3485342.83100.7951.86943.54540.9751 FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- WS2 (0.8 nm)-SM. As Table 15 represent the sensor structure based on WSe2, the sensor has dramatic responses from the RI of 1.3300 to 1.3485. In the initial stage of the process, a little change of RI (1.3300–1.33007) results in a constant resonant angle of 79.3904°, meaning no sensing, which means no detection. With the increase in RI, the resonance angle shifts effectively to 85.4765°, changed 6.0861° in total, which exhibits good sensitivity. The Rmin value increases from 0.0881 to 0.3495, suggesting enhanced light absorption, with Rmax being equivalent.Table 15FK51A-Ag- Ag3AsS3 (3 nm)-GaS (3 nm)- WSe2 (0.70 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.0881940.981579.39043.18491.330070.0882520.981579.39043.18720.0000701.33740.129223.467481.37643.46740.00741.9861.34110.166660.974582.59363.6120.01113.20321.34480.229890.974583.93893.6570.01484.54851.34850.349510.974485.47653.12350.01856.0861 Table 15FK51A-Ag- Ag3AsS3 (3 nm)-GaS (3 nm)- WSe2 (0.70 nm)-SM.SM’s RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{max}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\theta}_{res}$$\end{document}(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document})FWHMChange in RI\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\nabla \theta }_{res }(^\circ )$$\end{document}1.33000.0881940.981579.39043.18491.330070.0882520.981579.39043.18720.0000701.33740.129223.467481.37643.46740.00741.9861.34110.166660.974582.59363.6120.01113.20321.34480.229890.974583.93893.6570.01484.54851.34850.349510.974485.47653.12350.01856.0861 FK51A-Ag- Ag3AsS3 (3 nm)-GaS (3 nm)- WSe2 (0.70 nm)-SM. Regarding performance Table16, the sensitivity gradually rises from 268.38 to 328.98°/RIU and the QF raises to 105.32, implying the sharper and the more efficient response. The SNR is also improved and increased to 1.94, while the FoM and CSF both exhibit maximum performance and peak at the highest RI point, indicating clear and reliable sensing. Notably CSF at RI of 1.3374 is very high (258.37) which implies the good contrast at the lower analyte concentrations. In all, WSe2 features the combination of high sensitivity and density-dependent signal quality, justifying it as a robust candidate for CEA detection at different concentrations.Table 16FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- WSe2 (0.70 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /\mathrm{R}\mathrm{I}\mathrm{U}$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.3374268.3877.40046670.572763467.398778258.376691.3411288.5879.89384730.88682166.57873864.5414451.3448307.3384.03912531.243779064.71937062.5763731.3485328.98105.3236361.948487268.51197265.815687 Table 16FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- WSe2 (0.70 nm)-SM.SM’s RISensitivity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ /\mathrm{R}\mathrm{I}\mathrm{U}$$\end{document})QF (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${RIU}^{-1}$$\end{document})SNRFoMCSF1.3300–––––1.33007000001.3374268.3877.40046670.572763467.398778258.376691.3411288.5879.89384730.88682166.57873864.5414451.3448307.3384.03912531.243779064.71937062.5763731.3485328.98105.3236361.948487268.51197265.815687 FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)- WSe2 (0.70 nm)-SM. Here Fig. 5a represent the sensitivity verse RI values for various 2D materials here the sensitivity start from 225.08 to 350.61°/RIU, Fig. 5b shows the quality factor verse RI values for different 2D materials the highest QF register at MoS2 of 418.049 \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{R}\mathrm{I}\mathrm{U}}^{-1}$$\end{document}, Fig. 5c shows the SNR verse RI values for different 2D materials the highest SNR place at MoS2 of 7.733, Fig. 5d represent the FoM verse RI values various 2D materials the highest values placed at MoS2 216.36 and Fig. 5e shows the CSF verse RI values for different 2D materials the highest values register at MoS2.Fig. 5All sensing parameters for the 2D materials with respect to Analyte’s (RIU) (a) Sensitivity (b) QF (c) SNR (d) FOM (e) CSF. All sensing parameters for the 2D materials with respect to Analyte’s (RIU) (a) Sensitivity (b) QF (c) SNR (d) FOM (e) CSF. Fabrications steps The fabrication process of the proposed SPR sensor is clearly shown in Fig. 6. The prism with index of refraction n = 1.518 (namely the base substrate FK51A) is utilized in the construction of the multi-layer sensing structure due to its appropriate optical properties. First a thin layer of silver (Ag) is formed on the bottom face of the prism by sputtering or thermal evaporation. The thickness of the Ag layer is carefully controlled to be 54 nm, by monitoring the thickness of the quartz crystal, to obtain strong surface plasmon excitation and minimum reflectance. The upper dielectric layer and the 2D material layer are both protective layers, which enhance the chemical stability and long-term performance of Ag. A suitable thin-film deposition process like chemical vapor deposition (CVD) or pulsed laser deposition (PLD) is employed to deposit a suitable thin-film over the metal surface after the Ag deposition, usually a 3 nm layer of Ag3AsS3. This layer is beneficial for light confinement and to boost the plasmonic response. A 3 nm GaS layer is then deposited, to further enhance the optical confinement and the structural stability. The light–matter interaction and outstanding optical absorption properties of this nanoscale material HfSe2 are then utilized as the active 2D material. All thicknesses of all layers are precisely controlled at the nanometre scale, ensuring the accurate fabrication and optimal sensing performance. The molecules (CEA) are placed in a medium that senses the surface (HfSe2). The optimized multilayer structure leads to a more tightly confined electric field near the sensing interface, yielding more distinct resonances, increased sensitivity, and better bio-sensing performance.Fig. 6Fabrication process for proposed structure. Fabrication process for proposed structure. Comparative study Compared with various designs of SPR sensors, our SPR sensor with FK51A-Ag-Ag3AsS3-GaS-WS2 provides higher sensitivity. The sensitivity of the proposed sensor is 350.61°/RIU higher as compared to other presented sensors such as 144.72°/RIU for MoS2-Graphene (2022), 163.63°/RIU for Ti3C2Tx/Graphene (2025), and 186.6°/RIU for BP + WS2 on Si/Au (2023). The even MoS2–Graphene-based sensor in the optimized condition at 2020 exhibited 282°/RIU, still not as good as our sensitivity. Greater sensitivity suggests that a sensor is better at detecting smaller changes in the sample. Moreover, our sensor has a QF of 106.65 RIU−1, which reveals the sharp resonance curve. This indicates that our sensor design has better performance and could have a higher practical value in biosensing (Table 17).Table 17Comparative table for proposed work and existing work.AuthorSensor structureSensitivity(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document}∕RIU)QF (RIU−1)DADynamic Range (RI)Dynamic Range (RI)Kumar et al.,25MoS2–Graphene hybrid144.7282.4562.241.33–1.38Low concentration detectionKhodaie et al.,26MXene/Graphene163.63––1.33–1.37Improved CEA detectionCai et al.,27MoS2–Graphene282––1.33–1.36Moderate detection limitWu et al.,28Si/Au BP /WS2186.6––1.33–1.35Biomolecule sensingThis WorkAg/Ag3AsS3/GaS/WS2350.61106.6502.301.33–1.34High CEA concentration detection Table 17Comparative table for proposed work and existing work.AuthorSensor structureSensitivity(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ$$\end{document}∕RIU)QF (RIU−1)DADynamic Range (RI)Dynamic Range (RI)Kumar et al.,25MoS2–Graphene hybrid144.7282.4562.241.33–1.38Low concentration detectionKhodaie et al.,26MXene/Graphene163.63––1.33–1.37Improved CEA detectionCai et al.,27MoS2–Graphene282––1.33–1.36Moderate detection limitWu et al.,28Si/Au BP /WS2186.6––1.33–1.35Biomolecule sensingThis WorkAg/Ag3AsS3/GaS/WS2350.61106.6502.301.33–1.34High CEA concentration detection Comparative table for proposed work and existing work. Conclusion The proposed SPR sensor FK51A-Ag- Ag3AsS3 (3 nm)-GaS(3 nm)-WS2 (0.8 nm)-SM has shown excellent ability to detect integrated 2D materials such as BP, Graphene, MoS2, Mose2, HfSe2, WS2 and WSe2 based on multilayer structure. Through simulation and performance analysis, the sensor demonstrated a narrow FWHM, high SNR, FoM. WS2 demonstrated the highest sensitivity of 350.61°/RIU and the QF of 106.650 RIU−1, indicating its strong potential in detecting minimal index changes due to antigen binding. The inclusion of atomically thin 2D content increased plasmonic resonance and effectively limited the electric field in the sensing interface, thus improving the accuracy of detection. Compared to existing functions, this sensor design offers a simple yet highly efficient platform for biomedical diagnostics. These findings support the use of 2D content-assisted SPR sensors in detection of real-time, label-free and non-invasive cancer biomarker, paving the way for the next generation biosensing applications.