Experimental and 3D finite element modeling of line heating effect on thin mild steel sheets Authors: Galana Abay Kebede, Gamachis Ragasa Gutata, Gurmessa Horata Abbera, Bikila Debela Gemeda, Chala Abdissa Duressa Published: 2026 ABSTRACT Forming sheet metals by a moving heat source (i.e., line heating) is an efficient and economical method of forming metal sheets into desired shapes, including curvatures, which nowadays needs to replace convenient mechanical forming processes. However, only a few studies have been carried out on deforming steel sheets into a required shape by using an oxy-acetylene gas torch as a heat source using a numerical finite element model. This is mainly due to the difficulty of numerically modeling the amount of heat flux from the gas torch to the sheet metal, temperature distribution on the surface of the sheet, deformation resulting from different amounts of heat, analyzing the effect of the heat path, and experimentally maintaining the surface temperature of the sheet metal on a given path. Due to these difficulties, there is a weakness in judgment of where and how much to heat the material to obtain the required shape of the sheets. In this study for different amounts of heat flux from a gas torch to the surface of thin mild steel sheets, the temperature distribution on the surface of thin mild steel sheets is numerically modeled by 3D FEM software called ANSYS, and experimentally the surface temperature is controlled by a professional infrared thermometer on thin mild steel sheets of size 200 × 200 × 4 mm for straight, rectangular, and parallel path line heating to determine where and how much to heat the sheet to deform into desired shapes. Finally, the numerical and experimental results are compared, and the results obtained were fairly acceptable with the error less than 5–7% and in good agreement. Introduction Line heating (LH) is a thermo-mechanical method of forming plate or sheet metal by means of local heat treatments. There are two mechanisms commonly used to form steel plates/sheets into curved shells: mechanical forming and thermo-mechanical forming. In mechanical forming, a load is applied through a hydraulic press or a set of rolls to produce the required designed shape. Whereas in thermo-mechanical forming, thermal load is applied to obtain the desired shape1. When a plate is heated on one side, the through-thickness temperature gradient generated can cause different expansions across the thickness of the metal plate and bending of the plate/sheet2. Plastic deformation occurs in the region directly under the heat source where the temperature is high and the yield stress of the metal is low. This method is specially used in shipyard industries, the automotive industry, and with sheet metal forming technologies and other plate/sheet forming requirements3. Despite its utility, the process is difficult to control and generally regarded as art performed by the most skilled shipwrights. Therefore, it is essential to develop a scientific deterministic methodology of modeling the LH process using a heat source like an oxy-acetylene flame, which is widely used in heavy industry for metal cutting operations. Until today, a number of research have addressed the topic of line heating in search of better control of the process. Nomoto et al.4 had derived a simple relationship from their LH experimental results for modeling the process. Shin et al.5 had used numerical modeling for systematization of the line heating process. Clausen6 worked extensively on line heating of thick plates and contributed to devising methodology for deterministic simulation of the process considering the thermo-mechanical properties of the plates. Bae KY7 the formulas are derived from a statistical approach to the results of thermo-mechanical analyses using the finite element method (FEM) for combinations of practical heating parameters. Yoon Hwan Choi8 states that the main factors governing the quality of the manufactured products are the moving velocity of the heating source, heating strength, and heating ways. In this study, the temperature distributions of the heated plate were investigated with the condition that the line heating process was automatic. Chao Liu9 presents an optimal approach to laser scanning paths and heating condition determination for laser forming of doubly curved shapes. Pankaj Biswas10 predicted the transient thermal histories, taking into account the temperature-dependent thermo-mechanical properties. K. Venkadesh waran11 Laser forming of sheet metal is the bending process, induced by thermal stress, which is produced in the sheet by laser irradiation. A.P. Senthil Kumar12 The results obtained by the plane heat source method were compared with the results obtained by the line heat source method. Roger J. Anderson13 Experiments on Heating and Simulation of a Line of Plates. Still today further research is required for the automation and reduction of problems in the manual application of line heating by using an oxy-acetylene flame, as the process is difficult to control and generally regarded as an art performed by the most skilled workers. But less research is carried out on LH by oxy-acetylene flame, as a gas torch it is mostly available in almost all workshops of industries, and it’s economical. In this research on experimental and 3D finite element modeling of the line heating effect on thin mild steel sheets helps in advancing the line heating process using oxy-acetylene flame by solving those problems and providing experimental validation of numerical modeling. This research is applied in realistic applications for solving real problems. Principle of line heating When a steel sheet is heated locally by a moving heat source the heated region will expand more and also become soft enough to be distorted. The heated region is prevented from expanding side wards due to the surroundings are cold and there is a temperature gradient across the thickness. It will only be able to expand upwards, and will do so readily because it is softened, thereby making a lump. When the steel subsequently cools and hardens, this lump will remain, so that the surrounding steel will be pulled in to fill the space the lump has left. As a result, the steel sheet will distort. If a line on a sheet has been heated and cooled, there will be a line of such lumps, and the sheet will bend14. The process consists of increasing locally and quickly the temperature of one side of the sheet with a heating source, such as a torch, to induce plastic strains in the plate. During cooling, the sheet starts to deform such that the material in the heated region bends locally, resulting in permanent deformation in the sheet metal. The edges will rise towards the lump. This is the basic principle of line heating. Figure 1 shows the basic principle of how the deformation occurred by line heating. Fig. 1Basic principle of Line Heating. Basic principle of Line Heating. Similarly, thermally induced stresses can be used to remove strain, i.e., to eliminate distortion. Herein lies the idea of controlled heating and cooling for regulating strain so as to achieve a specified curvature or for removing undesired curvature. To generate the required shape of the mild steel sheet, the surface temperature (for mild steel it should not exceed 700℃, or recrystallization would happen), the speed of torch movement, the gap between the heating torch and the sheet surface, the nozzle diameter, and the heating pattern are important additional parameters. Material and methodologies Numerical and experimental methodologies The general procedures followed in finite element analysis and experimental works are shown in Fig. 2 below. The line heating process was performed using a single heating pass along the heating line to evaluate the resulting deformation behavior of the sheet. Fig. 2Numerical and Experimental methodologies. Numerical and Experimental methodologies. Material properties In this study a 3-D finite element model is used. The temperature-dependent material properties of C-Mn steel for the transient heat transfer and elasto-plastic analysis are presented in Table 1 below. The variations of yield stress and film coefficient of C-Mn steel with temperature are shown in Figs. 3a) and b), respectively. Table 1Temperature dependent material properties of mild steel source:15.Temperature (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^ \circ C)$$\end{document}Modulus of Elasticity/(GPa)PoissonRatioThermal Conductivity/\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{10}^{-6}/ ^\circ C$$\end{document} Thermal Conductivity \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:W{\left(MK\right)}^{-1}$$\end{document}Specific Heat \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:J{\left(Kg\:K\right)}^{-1}$$\end{document}02000.27861051.94501002000.30951151.1499.23002000.3311246.1565.54501500.3381341.05630.55501100.35751437.5705.5600880.37381435.6773.3720200.37381430641080.4800200.42381426931145020.47381529.45437.93Mechanical properties at normal condition:Ultimate Tensile strength = 440 MPa.Shear modulus=80Mpa.Briniell hardness = 126.Elongation at break (in 50 mm) = 15%. Table 1Temperature dependent material properties of mild steel source:15.Temperature (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^ \circ C)$$\end{document}Modulus of Elasticity/(GPa)PoissonRatioThermal Conductivity/\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{10}^{-6}/ ^\circ C$$\end{document} Thermal Conductivity \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:W{\left(MK\right)}^{-1}$$\end{document}Specific Heat \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:J{\left(Kg\:K\right)}^{-1}$$\end{document}02000.27861051.94501002000.30951151.1499.23002000.3311246.1565.54501500.3381341.05630.55501100.35751437.5705.5600880.37381435.6773.3720200.37381430641080.4800200.42381426931145020.47381529.45437.93Mechanical properties at normal condition:Ultimate Tensile strength = 440 MPa.Shear modulus=80Mpa.Briniell hardness = 126.Elongation at break (in 50 mm) = 15%. Temperature dependent material properties of mild steel source:15. Mechanical properties at normal condition: Ultimate Tensile strength = 440 MPa. Shear modulus=80Mpa. Briniell hardness = 126. Elongation at break (in 50 mm) = 15%. Fig. 3 a) Variation of yield stress with temperature, b) variation of film coefficient with temperature. (source:8) a) Variation of yield stress with temperature, b) variation of film coefficient with temperature. (source:8) Fig. 4Thin mild steel sheet for numerical analysis. Thin mild steel sheet for numerical analysis. Numerical analysis A numerical model is developed for thermo-mechanical analysis of the process of sheet metal forming by line heating and yields computerized calculations that are an important supplement to experiments. This numerical model has been built by use of the finite element code ANSYS release 16. The objective of the simulation in numerical analysis is to acquire the heating information necessary to form a given initial surface to a given target surface: heat regions, heating order, number of passes required, etc. In this numerical analysis: Rezoning technique is adopted to greatly reduce the simulation time. All the thermal and mechanical properties are considered as a function of temperature.Linear Newtonian convection cooling is considered on all the surfaces.The maximum temperature attained does not exceed 700 °C, phase change is not considered.A small strain and small deflection formulation has been applied. This is justified by the fact that the deformations induced by line heating are very small.The temperature field is unaffected by the structural response so that the thermal and structural problems can be solved in sequence. All the thermal and mechanical properties are considered as a function of temperature. All the thermal and mechanical properties are considered as a function of temperature. Linear Newtonian convection cooling is considered on all the surfaces. Linear Newtonian convection cooling is considered on all the surfaces. The maximum temperature attained does not exceed 700 °C, phase change is not considered. The maximum temperature attained does not exceed 700 °C, phase change is not considered. A small strain and small deflection formulation has been applied. This is justified by the fact that the deformations induced by line heating are very small. A small strain and small deflection formulation has been applied. This is justified by the fact that the deformations induced by line heating are very small. The temperature field is unaffected by the structural response so that the thermal and structural problems can be solved in sequence. The temperature field is unaffected by the structural response so that the thermal and structural problems can be solved in sequence. A specified initial temperature for the entire sheet metal,\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:T={T}_{\infty\:}\:\:\:\:\:\:\:\:for\:\:\:t=0$$\end{document} The heat input and the heating speed determine the thermal cycle, which has an important effect on the heat distribution pattern in the vicinity of the heat source. It is in this region that the heated zone is formed, characterized by temperature distribution over a time domain leading to the formation of a thermal strain field. The temperature distribution in a plate during the line for evaluating the residual deformation pattern of a line heated plate, heat transfer analysis is first carried out to find the nodal temperatures over a time domain. Then in the second part elasto-plastic analysis is carried out using the results obtained from the heat transfer analysis as inputs. The moving of the heat source was divided into several load steps. In the mechanical analysis the results from the thermal analysis were input as load. For each load step of thermal analysis corresponding rate independent structural analysis was carried out. The structural analysis involved thermo-elastic-plastic material model with temperature dependent material properties incorporated into the modelling. Numerical test for different path of line heating One most important factor controlling the final shape of the sheet is t heating line position. By considering the sheets of identical material and the same thickness, h, torch speed, v, and amount of heat, Q. during forming process the quantity of h and v are easily measured, but how much heat is actually absorbed by the sheet is difficult to say. Meanwhile the maximum temperature is very important as there must be some proportionality between the temperature and the local deformation. The surface temperature can be measured and is the function of other parameters Q, v and h. For these reasons, only maximum temperature is measured on the heated side and the plate thickness and torch velocity are considered in this simulation program. To obtain a certain deformation the heat input should be varied to get maximum temperature that will produce the required deformation. Table 2 below shows parameters of simulation for all path. Table 2Common Parameters for whole test.ParametersSymbols and unitsDescriptionHeat flowQ(W/s)changed to get maximum temperature that produce the deformation of sheetsTorch speedV(mm/s)Constant=20 mm/sTorch tip radiusR(mm)Constant =5 mmThickness of the sheetsT(mm)Constant=4 mm Table 2Common Parameters for whole test.ParametersSymbols and unitsDescriptionHeat flowQ(W/s)changed to get maximum temperature that produce the deformation of sheetsTorch speedV(mm/s)Constant=20 mm/sTorch tip radiusR(mm)Constant =5 mmThickness of the sheetsT(mm)Constant=4 mm Common Parameters for whole test. Center path line heating The sheet is heated at its center by a different amount moving heat source. The sheet is fine meshed with an area of 20 × 10 mm along its center having 6170 nodes and 832 elements for advantage of reducing computation time, the remaining area is in coarser mesh shown in Fig. 4a). Finite element modeling of line heating for prediction of temperature distribution by varying the amount of heat input (i.e. 1000–2400 W/s with 200w/s range) are simulated by ANSYS. Simulation result of temperature distribution and total deformation at 2000 W/s heat flow are shown in Fig. 5b) and c) respectively. Fig. 5a) Mesh view b) Temperature distribution c) Deformation for center path line heating. a) Mesh view b) Temperature distribution c) Deformation for center path line heating. Generally, the summary of the results obtained from the simulation are given in Table 3. The simulation shows that the temperature is increasing with the amount of heat source and the maximum temperature is at the top surface where the heat is applied and decreasing along the thickness of sheets. The transient temperature distributions of the sheets used in the line heating process is responsible for the strain gradient and residual deformation. This causes the sheet metal to bend in heated direction in to V-shapes. Table 3Center path line heating simulation results.Heat flow Q, (watt/sec)Maximum temperature (℃)Total maximum deformation(mm)Maximum direction deformation(mm)Maximum Equivalent strain(mm⁄mm)Thermal strain(mm/mm)1000267.80.05970.0071100.00270250.0028821200317.60.08850.0100150.00371760.0035411600417.80.10070.0118880.00449630.0049661800468.10.11480.0135590.00508820.0053392000518.60.12880.0152640.00566530.0065482200595.60.14310.0169920.00651860.0074172400620.30.15750.0187550.00257040.084262 Table 3Center path line heating simulation results.Heat flow Q, (watt/sec)Maximum temperature (℃)Total maximum deformation(mm)Maximum direction deformation(mm)Maximum Equivalent strain(mm⁄mm)Thermal strain(mm/mm)1000267.80.05970.0071100.00270250.0028821200317.60.08850.0100150.00371760.0035411600417.80.10070.0118880.00449630.0049661800468.10.11480.0135590.00508820.0053392000518.60.12880.0152640.00566530.0065482200595.60.14310.0169920.00651860.0074172400620.30.15750.0187550.00257040.084262 Center path line heating simulation results. Rectangular path line heating The sheet is heated in rectangular path by a different amount moving heat source. The sheet is fine meshed with an area of 20 × 20 mm along its center having 6862 nodes and 952 elements for advantage of reducing computation time, the remaining area is in coarser mesh as shown in Fig. 5a). Finite element modeling of line heating for prediction of temperature distribution by varying the amount of heat input (i.e. 1000–3000 W/s with 500w/s range) are simulated by ANSYS. Simulation result of temperature distribution and total deformation at 1000w/s are shown in Fig. 6b) and c) below. Fig. 6a) Mesh view b) Temperature distribution c) Deformation for rectangular path line heating. a) Mesh view b) Temperature distribution c) Deformation for rectangular path line heating. From Fig. 5. b, c) and the summary of simulation results for rectangular path shown in Table 4 the temperature at surface is increasing with the amount of heat source and deflection is maximum at the position far from center and it causes the sheet to deform to along the heating lines in to a double curved form which is impossible to obtain by other machines like rolling, bending and punching machines. Table 4Rectangular path line heating simulation results.Heat(Q)In (W/s)Max. Temperature(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^ \circ C$$\end{document})Max. Total Deformation (mm)Max. Directional Deformation in X-Axis(mm/mm)Equivalent TotalStrain (mm/mm)Max. Thermal Strain(mm)1000203.640.17650.02090.0014850.0002061500293.230.25100.031720.0022380.0032022000381.600.36800.042730.002990.0044132500496.380.49170.053890.0037350.0057333000557.320.62230.588820.0047840.007151 Table 4Rectangular path line heating simulation results.Heat(Q)In (W/s)Max. Temperature(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^ \circ C$$\end{document})Max. Total Deformation (mm)Max. Directional Deformation in X-Axis(mm/mm)Equivalent TotalStrain (mm/mm)Max. Thermal Strain(mm)1000203.640.17650.02090.0014850.0002061500293.230.25100.031720.0022380.0032022000381.600.36800.042730.002990.0044132500496.380.49170.053890.0037350.0057333000557.320.62230.588820.0047840.007151 Rectangular path line heating simulation results. Parallel path line heating The sheet is heated in parallel path by a different amount moving heat source. The sheet is fine meshed with an area of 20 × 10 mm along its center having 10144 nodes and 1375 elements for advantage of reducing computation time, the remaining area is in coarser mesh as shown in Fig. 7a). Simulation result of temperature distribution and total deformation at 1000w/s are shown in Fig. 6b) and c) bellow. Fig. 7a) Mesh view b) Temperature distribution, c) deformation for parallel path line heating. a) Mesh view b) Temperature distribution, c) deformation for parallel path line heating. Here the maximum temperature (611.41\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ C$$\end{document}) achieved at small heat input (2000 W) because of two heating lines are done. Due the temperature gradient in the thickness direction the sheet is deformed at heated line causing the sheet to deform to some like cylinder shape. The summary of simulation result are given in Table 5 below. Table 5Parallel line heating simulation results.Heat Q, (watt/sec)Maximum temperature \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left(℃\right)$$\end{document}Total maximum deformation\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left(mm\right)$$\end{document}Maximum direction deformation\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left(\raisebox{1ex}{$mm$}\!\left/\:\!\raisebox{-1ex}{$mm$}\right.\right)$$\end{document}Maximum Equivalent strain\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left(\raisebox{1ex}{$mm$}\!\left/\:\!\raisebox{-1ex}{$mm$}\right.\right)$$\end{document}Thermal strain\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left(\raisebox{1ex}{$mm$}\!\left/\:\!\raisebox{-1ex}{$mm$}\right.\right)$$\end{document}1000316.20.074110.00900.0035080.003501500463.40.117590.013970.0055580.0056402000611.40.164660.020070.0082650.008233 Table 5Parallel line heating simulation results.Heat Q, (watt/sec)Maximum temperature \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left(℃\right)$$\end{document}Total maximum deformation\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left(mm\right)$$\end{document}Maximum direction deformation\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left(\raisebox{1ex}{$mm$}\!\left/\:\!\raisebox{-1ex}{$mm$}\right.\right)$$\end{document}Maximum Equivalent strain\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left(\raisebox{1ex}{$mm$}\!\left/\:\!\raisebox{-1ex}{$mm$}\right.\right)$$\end{document}Thermal strain\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left(\raisebox{1ex}{$mm$}\!\left/\:\!\raisebox{-1ex}{$mm$}\right.\right)$$\end{document}1000316.20.074110.00900.0035080.003501500463.40.117590.013970.0055580.0056402000611.40.164660.020070.0082650.008233 Parallel line heating simulation results. Experimental analysis Three experiments are carried out to validate the numerical analysis. The experiments are done on mild steel sheet of size 200 × 200 × 4 mm for center, rectangular and parallel path line heating. The surface temperature with time, the resulting deformation are measured from the experiment. Prior to applying heat to the sheet metal, dirty substances are removed from it and heating paths are marked on each sheet metals, then heat the sheet metal in given path with carburizing flame by maintaining constant gap (20 mm) from the heating surface. Along the torch non-contact type, surface measuring temperature device called professional infrared thermocouple (PIT) is used and shown in Fig. 8 below. A linear variable differential transformer (LVDT) with digital indicator was used for measuring the deformation of the sheet due to line heating of the control points. Fig. 8a) Front view of PIT b) PIT measuring temperature. a) Front view of PIT b) PIT measuring temperature. Experimental analysis for center path line heating Heating is done along its center at equal distance from both ends. A small spot is made by a punch and hammer to show its center and guide the path during line heating processes, as shown in Fig. 9(a) below. Fig. 9Mild steel sheet a) Before heating b) After heating. Mild steel sheet a) Before heating b) After heating. Initially when the sheet is started to heat it takes more time to reach the maximum temperature. Then after the time to reach maximum temperature is small as the sheet is getting some temperature from initial by conduction heat transfer. Finally the sheet is cooled to its original room temperature. Also the temperature at the bottom of the sheet is smaller than that of the top surface resulting temperature gradient; which causes the sheet to deform. For comparing the result with numerical at maximum temperature of 620.31\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:^\circ C$$\end{document} the maximum total deformation of the sheet is 0.18 mm. As we see from Fig. 9b) finally the sheet is deformed to V-shape due to effect of line heating along the center. Experimental analysis for rectangular path line heating The heating is done in rectangular path on the sheet. Small spot is done by nail and hammer is made to show the path and to guide the person during line heating. Figure 9 shows the rectangular path for line heating of mild steel sheet. Fig. 10Mild steel sheet a) Before heating b) After heating. Mild steel sheet a) Before heating b) After heating. From the experiment the peak surface temperature is increasing the deformation also increasing. For comparing the result with numerical at maximum temperature of 553.6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^\circ C$$\end{document} the maximum deformation of the sheet is 0.65 mm. Finally the sheet is deformed to double curved structure because of the compressive stress are applied along the rectangular path due to line heating effect. This result is comparative to simulation result as shown in Fig. 10b). Experimental analysis for parallel path line heating In this experiment the heat was applied in the same direction along two parallel line of heating as shown in Fig. 11a) below. The maximum surface temperature on the sheets is along the heating line is to be at 611.41 \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^ \circ C$$\end{document} and the initial surface temperature is almost at room temperature 26.2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^ \circ C$$\end{document}. Fig. 11Mild steel sheet a) Before heating b) After heating. Mild steel sheet a) Before heating b) After heating. The mild sheet requires small time to achieve the maximum temperature because there will be conduction heat transfer for when heating is done in parallel. Also we observe that near the end it takes small time to achieve maximum temperature. There are temperature gradient in a thickness direction this causes the sheet to deform along the heating path due to the compressive force along each line of heating. Figure 11b) shows the sheet is finally deformed into a cylindrical shape due to effect of line heating. Result and discussion From numerical analyses of line heating effect on thin mild steel sheet the valuable information obtained to compare the results with that of experimental effects of line heating on sheets. Under this the effect changing the amount of heat on surface temperature of the sheet, the relation between temperature and deformation of the sheet, temperature profile versus time graph, the effect of changing the heating path and validation of numerical deformation by experiment are discussed for center, rectangular and parallel path line heating. Thermal analysis result The aim of line heating process is to deform a sheet to the desired degree and with minimum spring back effect. The sheet bending by line heating is the result of plastic deformation due to prolonged application of heat source on a predetermined path. The Fig. 12 bellow show that comparison results of the transient temperature distribution of single pass line heating for different path of heating from experimental and 3D FEM thermo-mechanical simulations. Fig. 12Heat flow versus temperature for three path of line heating. Heat flow versus temperature for three path of line heating. From Fig. 12, for the same heat flow for example three cases has different temperature value. i.e. parallel line heating has higher temperature than others because the heat is applied at the same time along two path that causes the temperature to rise more than other path. In general the temperature is increasing almost proportionally with the heat. Figure 13 below shows the graph of temperature versus thermal strain for center, rectangular and parallel path line heating. Fig. 13Temperature versus thermal strain graph. Temperature versus thermal strain graph. The thermal strain is directly proportional to temperature of each type of line heating path and this strain in heated region is responsible for the deformation of the sheets as shown Fig. 13 above. The temperatures are measured on the top surface of the sheet during experiments and comparisons between those and simulated temperatures is given in Fig. 14. This graph shows the temperature as a function of time at a fixed point on the top surface-both measured and simulated. There is a good agreement between measured and simulated temperatures, on the top surface. Although the simulated sheet cools little too quickly (either due to surface heat loss conduction). Fig. 14Measured and simulated temperature profile. Measured and simulated temperature profile. Mechanical analysis results From investigation the deformation of line heating depends on factors like heating path, heat source type, distribution of heat source, rate of heat input, sheet thickness, know when the heat source (Oxy-acetylene flame) moves over the Path in the domain, temperature and strain gradient are induced in the sheet. The measurement of permanent deformation is important to know the effectiveness of line heating process. Table 6 below shows that the comparison of experimental and 3D FEM simulation results of the mild steel sheet metal deformational for different path of line heating at pick temperature.\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\mathrm{P}\mathrm{e}\mathrm{r}\mathrm{c}\mathrm{e}\mathrm{n}\mathrm{t}\mathrm{a}\mathrm{g}\mathrm{e}\:\mathrm{o}\mathrm{f}\:\mathrm{e}\mathrm{r}\mathrm{r}\mathrm{o}\mathrm{r}\:=\frac{\mathrm{N}\mathrm{u}\mathrm{m}\mathrm{e}\mathrm{r}\mathrm{i}\mathrm{c}\mathrm{a}\mathrm{l}\:\mathrm{v}\mathrm{a}\mathrm{l}\mathrm{u}\mathrm{e}-\mathrm{E}\mathrm{x}\mathrm{p}\mathrm{e}\mathrm{r}\mathrm{i}\mathrm{m}\mathrm{e}\mathrm{n}\mathrm{t}\mathrm{a}\mathrm{l}\:\mathrm{v}\mathrm{a}\mathrm{l}\mathrm{u}\mathrm{e}}{\mathrm{E}\mathrm{x}\mathrm{p}\mathrm{e}\mathrm{r}\mathrm{i}\mathrm{m}\mathrm{e}\mathrm{n}\mathrm{t}\mathrm{a}\mathrm{l}\:\mathrm{v}\mathrm{a}\mathrm{l}\mathrm{u}\mathrm{e}}\times\:\:100\%$$\end{document} Table 6Numerical and experimental comparison of deformation.Heating PathPeak temperature (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^ \circ C$$\end{document})Numerical result(mm)Experimental result(mm)Error (%)Center620.310.157580.147826.6Rectangular557.320.62230.58985.5Parallel611.410.164660.153747.1 Table 6Numerical and experimental comparison of deformation.Heating PathPeak temperature (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$^ \circ C$$\end{document})Numerical result(mm)Experimental result(mm)Error (%)Center620.310.157580.147826.6Rectangular557.320.62230.58985.5Parallel611.410.164660.153747.1 Numerical and experimental comparison of deformation. Figure 15 shows the comparison of measured value and numerical value of deformation for center, rectangular and parallel path line heating. This value are taken for peak temperature of three cases. Fig. 15Comparison between measured and simulated deformation. Comparison between measured and simulated deformation. The agreement between measured and simulated deflection described above means that the difference in a cooling rate doesn’t influence the result. So, that the deformation of the experiment was successful, it demonstrates that the numerical model is capable of simulating the actual behavior of the mild steel sheet being heated. The Fig. 16 bellow shows shape agreement between numerical and experimental result for (a) center (b) rectangular and (c) parallel path of line heating. Fig. 163D finite element modeling simulation and experimental validation for a) parallel, b) center and c) rectangular path. 3D finite element modeling simulation and experimental validation for a) parallel, b) center and c) rectangular path. Conclusion From the experimental and 3D finite element modeling of line heating effect on thin mild steel sheet the conclusion reached are as described below. The maximum temperature at the top surface of the sheet increased with increasing input power. Furthermore, temperature gradients between the upper and lower surfaces of the sheet increased significantly as the input power increased; this could be a primary factor in increasing the deformation.The heating path determined by numerical model to give a certain shape of the sheet has a good agreement with experimental result, so one can get required information for heating path from numerical results before proceeding to actual line heating of the sheet.The transient temperature distributions of the sheet used in the line heating process is responsible for the strain gradient and residual deformation.Fine meshing of heated zone been employed to greatly reduce the simulation time yet preserve the required accuracy.The required amount of deformation of sheet may not achieved by a single pass line heating. Therefore, more number of pass is needed to get that deformation.Results obtained from numerical analysis matched well with experimental results.Line heating metal forming techniques are applicable in realistic applications to solve real problems.The findings demonstrates that line heating is an effective and practical metal forming technique with direct relevance to industrial applications such as shipbuilding plate forming, repair and correction of distorted steel structures, and low-cost forming operations in workshop environments where advanced forming equipment may not be available. Specifically, the method addresses key industrial challenges including controlled bending of large thin plates, correction of welding-induced distortions and achieving desired curvature without extensive mechanical loading or expensive tooling. The maximum temperature at the top surface of the sheet increased with increasing input power. Furthermore, temperature gradients between the upper and lower surfaces of the sheet increased significantly as the input power increased; this could be a primary factor in increasing the deformation. The maximum temperature at the top surface of the sheet increased with increasing input power. Furthermore, temperature gradients between the upper and lower surfaces of the sheet increased significantly as the input power increased; this could be a primary factor in increasing the deformation. The heating path determined by numerical model to give a certain shape of the sheet has a good agreement with experimental result, so one can get required information for heating path from numerical results before proceeding to actual line heating of the sheet. The heating path determined by numerical model to give a certain shape of the sheet has a good agreement with experimental result, so one can get required information for heating path from numerical results before proceeding to actual line heating of the sheet. The transient temperature distributions of the sheet used in the line heating process is responsible for the strain gradient and residual deformation. The transient temperature distributions of the sheet used in the line heating process is responsible for the strain gradient and residual deformation. Fine meshing of heated zone been employed to greatly reduce the simulation time yet preserve the required accuracy. Fine meshing of heated zone been employed to greatly reduce the simulation time yet preserve the required accuracy. The required amount of deformation of sheet may not achieved by a single pass line heating. Therefore, more number of pass is needed to get that deformation. The required amount of deformation of sheet may not achieved by a single pass line heating. Therefore, more number of pass is needed to get that deformation. Results obtained from numerical analysis matched well with experimental results. Results obtained from numerical analysis matched well with experimental results. Line heating metal forming techniques are applicable in realistic applications to solve real problems. Line heating metal forming techniques are applicable in realistic applications to solve real problems. The findings demonstrates that line heating is an effective and practical metal forming technique with direct relevance to industrial applications such as shipbuilding plate forming, repair and correction of distorted steel structures, and low-cost forming operations in workshop environments where advanced forming equipment may not be available. Specifically, the method addresses key industrial challenges including controlled bending of large thin plates, correction of welding-induced distortions and achieving desired curvature without extensive mechanical loading or expensive tooling. The findings demonstrates that line heating is an effective and practical metal forming technique with direct relevance to industrial applications such as shipbuilding plate forming, repair and correction of distorted steel structures, and low-cost forming operations in workshop environments where advanced forming equipment may not be available. Specifically, the method addresses key industrial challenges including controlled bending of large thin plates, correction of welding-induced distortions and achieving desired curvature without extensive mechanical loading or expensive tooling.