Design of a slotted bowtie dual-polarized antenna for Sub-6 GHz multi-service wireless applications Authors: Saranya Matta, Sambhudutta Nanda Published: 2026 ABSTRACT The manuscript presents the design and experimental validation of a dual-band, dual-polarized slotted bowtie antenna for sub-6 GHz wireless applications. The proposed antenna utilizes a 2-stage work approach, where stage-1 features a trapezoidal slot-engineered bowtie radiators arranged orthogonally on a FR4 substrate and excited through a balanced feeding configuration, along with a 100 mm × 100 mm finite metallic reflector placed at an optimized distance of 28.4 mm in stage-2, facilitating reflector-assisted dual-band operation with improved radiation performance. The proposed antenna operates at frequencies of 2.52 GHz and 4.42 GHz, with measured impedance bandwidths of approximately 220 MHz and 420 MHz, respectively. The proposed antenna achieves high port isolation levels of 40 dB and 33.5 dB, with isolation surpassing 30 dB throughout the operational bands. The design sustains cross-polarization levels beneath − 15.8 dB and a front-to-back ratio exceeding 23 dB. The incorporation of the reflector significantly enhances the antenna gain from an average of 2 dBi to 7.14 dBi, with a peak measured gain of 7.6 dBi and 6.63 dBi at the two operating frequencies. The observations show that the proposed antenna is appropriate for sub-6 GHz multi-service wireless systems since it offers a compact and efficient solution for dual-band, dual-polarized operation with high isolation and gain, along with enhanced radiation characteristics. Introduction The demand for compact, lightweight, dual-polarized antennas with high isolation, low cross-polarization, stable radiation patterns, and enhanced forward gain has grown with the expansion of sub-6 GHz wireless access systems. These requirements are particularly critical for access points, small cells, and infrastructure platforms supporting multiple coexisting services. Bowtie antennas remain attractive among planar radiators due to their simple geometry, ease of fabrication, and suitability for polarization diversity. The proposed antenna, though not tailored to a specific 5G NR band, exhibits an upper resonance near 4.42 GHz within the sub-6 GHz spectrum relevant to enhanced mobile broadband and private cellular networks. Its lower resonance around 2.52 GHz aligns closely with the widely used 2.4 GHz ISM band, enabling support for WLAN, IoT applications and small-cell or access-point deployments requiring dual-band and dual-polarized operation. This dual-band response makes it suitable for multi-standard sub-6 GHz architectures. Furthermore, slot-loading techniques in antenna design have proven effective for modifying current distribution, introducing additional resonant modes, and enhancing design flexibility without increasing antenna size. Recent studies have observed advanced antenna design techniques to improve performance in modern wireless systems. Hybrid optimization and deep learning-based approaches have been explored for effective resource allocation in MIMO-enabled networks1. Furthermore, it has been claimed that antenna designs with metamaterial-based structures and frequency selective surfaces (FSS) increase gain and decrease mutual coupling2,3. CPW-fed structures and circularly polarized MIMO antennas have been designed for millimetre-wave and wideband applications4–6. In the meanwhile, slot-based and reflector-backed antenna topologies have been investigated to improve radiation characteristics and facilitate multiband behaviour7,8. Nevertheless, the majority of these studies concentrate on millimetre-wave or broadband systems that have greater structural complexity. In contrast, the suggested approach uses a straightforward planar slot-engineered bowtie radiator with reflector-assisted resonance to accomplish regulated dual-band dual-polarized functioning. Various methods have been explored to enhance antenna bandwidth. Approaches such as slot-loaded radiators, multilayer parasitic elements, bent microstrip lines, and defective ground structures9–12 improve impedance bandwidth but often lead to multilayer designs, structural complexity, or fabrication challenges. Similarly, techniques including hybrid couplers, stacked patches, orthogonal feeding networks, and multi-element designs13–17 have been proposed to improve port isolation, though most require intricate feeding arrangements or achieve only moderate isolation (14–22 dB). Gain enhancement strategies for bowtie and dipole antennas have also been reported12,15,18–21, with typical gains ranging from 1.5 dBi to 3.3 dBi. Radiation efficiency improvements using multilayer substrates, coplanar waveguide feeds, or embedded structures14,16,22,23 generally remain below 70%, often compromising antenna profile, fabrication simplicity, or scalability for wireless applications deployment. Cross-polarization suppression is another critical requirement for dual-polarized antennas. Techniques such as cavity-backed structures, parasitic loading, balun-based feeding, and magneto-electric dipoles24–28 have achieved levels below − 20 dB, but typically rely on complex feed networks or bulky cavity structures. Slotted bowtie antennas have attracted significant interest for their broadband characteristics and planar design29–32. Slot loading increases effective electrical length and aperture area, thereby improving bandwidth and radiation performance without enlarging the physical size. However, most reported designs support only single linear polarization, limiting their suitability for modern sub-6 GHz 5G wireless systems. Reflector integration is a well-established method to reduce backward radiation and enhance gain, front-to-back ratio, and isolation. Cavity-backed and reflector-assisted designs13,33–39 demonstrate improved directionality and isolation, though often at the expense of bandwidth or structural simplicity. Most reported dual-polarized bowtie, loop, and crossed-dipole antennas achieve enhanced performance through complex multilayer structures, intricate feeding networks, or bulky cavity-backed arrangements. However, there remains a need for a structurally simple and easily fabricated dual-polarized antenna that can simultaneously provide adequate impedance bandwidth, high port isolation, enhanced front-to-back ratio, low cross-polarization, and stable gain for sub-6 GHz multi-service wireless systems. To address this need, this work presents a systematic slot-engineered modification of a bowtie-based radiator. The proposed antenna uses a reflector-assisted resonance mechanism in conjunction with trapezoidal slot-engineered bowtie elements, enabling controlled dual-band operation while preserving a simple planar configuration. The main contributions of this work are summarized as follows: Unlike conventional loop cross-dipole antennas, which are typically designed to achieve broadband behaviour through loop-based resonators, the proposed antenna structure (Novelty) achieves controlled dual-band operation through the interaction between slot-tuned bowtie radiators and an optimally spaced reflector, a reflector-assisted mechanism that introduces a higher-order resonance while improving gain and front-to-back ratio, a balanced feeding configuration achieving high port isolation and reduced cross-polarization, and comprehensive experimental validation and parametric analysis demonstrating stable radiation characteristics. Antenna design Antenna design methodology and evolution The proposed dual-port, dual-band sub-6 GHz planar slotted bowtie dipole antenna is developed through a two-stage methodology: a developmental stage followed by a concluding stage. Final dimensions are determined via systematic parametric sweeps and manual refinement based on electromagnetic insight, rather than automated numerical optimization. During the developmental stage, fabrication proceeds in two phases. In the primary phase, Antenna-A—a planar slotted bowtie printed on a substrate with permittivity 4.4 and thickness 0.8 mm—is realized. The trapezoidal slot configuration is selected to achieve resonance at 2.6 GHz, the principal operating band of the radiator. The slotted bowtie represents an advanced form of the traditional dipole, incorporating slots within its triangular elements. As shown in Figs. 1, and 2, Antenna-A’s top, and side views illustrate a compact planar bowtie dipole resonating at 2.6 GHz. The trapezoidal slots modify surface current paths, enabling controlled resonance while maintaining a simple planar geometry.Fig. 1Top-view schematic layout of Antenna-A (image generated from simulation tool by the authors).Fig. 2Side-view schematic profile of Antenna-A (image generated from simulation tool and annotated by the authors). Top-view schematic layout of Antenna-A (image generated from simulation tool by the authors). Side-view schematic profile of Antenna-A (image generated from simulation tool and annotated by the authors). Figure 3 illustrates the secondary phase of the developmental stage, with the top view of Antenna-B, while Fig. 4 shows its side view. In this design, two identical planar slotted bowties are printed orthogonally on the substrate along their central axes, forming Antenna-B, which resonates at 2.7 GHz to achieve dual linear polarization. The crossed-dipole bowtie configuration enables a low-profile structure, and the orthogonal arrangement ensures polarization diversity.Fig. 3Top-view schematic layout of Antenna-B (image generated from simulation tool by the authors).Fig. 4Side-view schematic profile of Antenna-B (image generated from simulation tool and annotated by the authors). Top-view schematic layout of Antenna-B (image generated from simulation tool by the authors). Side-view schematic profile of Antenna-B (image generated from simulation tool and annotated by the authors). The proposed antenna employs a balanced feeding structure to excite the orthogonal slotted bowtie radiators. Two coaxial cables and two shorting pins are used in the balanced feeding setup, which is depicted in Fig. 5.Fig. 5Graphical presentation of balanced feed configuration (the illustration was created by the authors). Graphical presentation of balanced feed configuration (the illustration was created by the authors). One coaxial line is placed (C1)/2 from the patch centre, and the second at (C2)/2, both parallel to the centreline. One arm of the bowtie dipole connects to the coaxial feed’s outer conductor, while the other connects to the shorting pin. By linking the inner conductor to two shorting pins, enhanced port isolation is achieved. This balanced feed is implemented using two symmetric feed points along with shorting pins, which ensure equal and opposite current distribution on the bowtie arms. This balanced excitation suppresses common-mode currents and improves polarization purity, impedance matching, radiation efficiency, and pattern symmetry. In stage two (concluding stage), Antenna-B evolves into the final structure, Antenna-C. Figures 6, and 7 present its top, and side views, illustrating the dual-band, dual-polarized sub-6 GHz antenna. Antenna-C is realized by coupling a square metal reflector to Antenna-B with an optimized gap (H-dimension). The finite reflector modifies radiator–ground coupling, enhancing forward radiation at lower frequencies and enabling dual-band operation.Fig. 6Proposed antenna (Antenna-C) with dimensions (image generated from simulation tool and annotated by the authors).Fig. 7Proposed antenna (Antenna-C) Side-view (image generated from simulation tool and annotated by the authors). Proposed antenna (Antenna-C) with dimensions (image generated from simulation tool and annotated by the authors). Proposed antenna (Antenna-C) Side-view (image generated from simulation tool and annotated by the authors). An optimal spacing of H = 28.4 mm between the reflector and substrate balances impedance matching, gain, and polarization performance. The resulting reflector-backed planar bowtie antenna (RBPBA) achieves improved gain, directivity, and radiation efficiency. The exact dimensional values of the proposed antenna are listed in Table 1.Table 1Design dimensions of the proposed antenna.Sl.no.DimensionValues in mm1SW422SL403G1004H28.45L117.26L210.27L348L439W1510W2811W3212W4413W5114C1815C26.6 Table 1Design dimensions of the proposed antenna.Sl.no.DimensionValues in mm1SW422SL403G1004H28.45L117.26L210.27L348L439W1510W2811W3212W4413W5114C1815C26.6 Design dimensions of the proposed antenna. Figures 8 and 9 show the fabricated antennas at the evolving stage (without a square ground plane) and the final stage (with a square ground plane), while Fig. 10 presents the side view of the final design, Antenna-C.Fig. 8Fabricated Antenna-B prototype without reflector (Photograph taken by the authors).Fig. 9Top view of the Fabricated Antenna-C prototype with reflector (photograph taken by the authors).Fig. 10Side-view of the Fabricated Antenna-C prototype with reflector (photograph taken by the authors). Fabricated Antenna-B prototype without reflector (Photograph taken by the authors). Top view of the Fabricated Antenna-C prototype with reflector (photograph taken by the authors). Side-view of the Fabricated Antenna-C prototype with reflector (photograph taken by the authors). The procedure for determining the initial dimensions of the slotted bowtie dipole is outlined in the following section. Formulation of initial dimensions Due to the complex reflector coupling and slot geometry, a closed-form solution is not feasible. Instead, initial dimensions are derived using first-order analytical approximations, followed by refinement through full-wave simulations. The geometric length of the bowtie arm is based on an equivalent half-wavelength dipole model, which approximates the fundamental resonance of the slotted bowtie radiator. The fundamental resonance occurs when the effective electrical length satisfies:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{\mathrm{eff}}\approx \frac{{\lambda}_{g}}{2}= 36.23 \mathrm{m}\mathrm{m}$$\end{document}where the guided wavelength is\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\lambda}_{g}=\frac{c}{{f}_{1}\sqrt{{\varepsilon}_{\mathrm{eff}}}}= 72.45 \mathrm{m}\mathrm{m}$$\end{document}and the effective permittivity is approximated as\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varepsilon}_{\mathrm{eff}}\approx \frac{{\varepsilon}_{r}+1}{2}= \frac{5.4}{2}=2.7$$\end{document} So, the effective length for the lower resonance is: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{\mathrm{eff,1}}\approx \frac{c}{2{f}_{1}\sqrt{{\varepsilon}_{\mathrm{eff}}}}$$\end{document} = 0.03623 m = 36.23 mm. Here, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${f}_{1}$$\end{document} corresponds to the lower operating frequency (≈ 2.52 GHz). The initial bowtie arm length is determined by this relation and then varied using simulation. The trapezoidal slot length is expressed in terms of slanted side length and effective slot width. The trapezoidal slots effectively increase the radiator’s electrical length by altering surface current paths. Slot parameters such as width, length, and taper provide additional degrees of freedom for resonance tuning. While the slots alone do not generate the upper band, they enable strong coupling with the reflector, which is essential for dual-band behaviour in the final design. The Final Expression for effective Trapezoidal slot length is expressed as:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{\mathrm{slot}}={L}_{s}+2{W}_{s}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{s}$$\end{document} is the slanted side length, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${W}_{s}$$\end{document} is the effective slot width.\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{s}=\sqrt{{h}^{2}+{\left(\frac{{W}_{top}-{W}_{bot}}{2}\right)}^{2}}=\sqrt{{(10.2)}^{2}+{\left(\frac{4-2}{2}\right)}^{2}}=10.248 \mathrm{m}\mathrm{m}$$\end{document}where h is the vertical height of trapezoid slot, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${W}_{top}$$\end{document} is the top opening width, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${W}_{bot}$$\end{document} is the bottom opening width. Since the current spreads over both top and bottom edges, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${W}_{s}$$\end{document} is taken as the average slot width:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${W}_{s}=\frac{{W}_{top}+{W}_{bot}}{2}=\frac{4+2}{2}=3 \mathrm{m}\mathrm{m}$$\end{document} Hence,\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{\mathrm{slot}}=\sqrt{{h}^{2}+{\left(\frac{{W}_{top}-{W}_{bot}}{2}\right)}^{2}}{\hspace{0.05em}}+{\hspace{0.05em}}2\left(\frac{{W}_{top}+{W}_{bot}}{2}\right)$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{\mathrm{slot}}= 10.248\hspace{0.17em}+\hspace{0.17em}2 \mathrm{x} (3)\hspace{0.17em}=\hspace{0.17em}16.248 \mathrm{m}\mathrm{m}.$$\end{document} The effective slot length can be used to first estimate the upper resonant frequency as\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${f}_{2}\approx \frac{c}{2{L}_{\mathrm{slot}}\sqrt{{\varepsilon}_{\mathrm{eff}}}}.$$\end{document} First-order estimation provides the initial layout guideline, with full-wave simulations and measurements confirming the upper-band resonance at 4.42 GHz. This response arises from the tapered slot geometry, fringing fields, and strong coupling induced by the orthogonal slot configuration and finite reflector. In the proposed bowtie configuration, the theoretical input impedance (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${Z}_{\mathrm{in}})$$\end{document} is primarily dependent on the flare angle40 and can be expressed as follows:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${Z}_{\mathrm{in}}\approx 120 \mathrm{l}\mathrm{n}(\mathrm{cot}\frac{\alpha }{4})$$\end{document} The overall system performance is enhanced through careful adjustment of the radiator flare angle (α), the orthogonal arrangement of the radiating elements, and the size of the backing reflector. In this design, an \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$80^\circ$$\end{document} flare angle is chosen to provide stable dual-band characteristics, improved radiation efficiency, and impedance matching. To obtain enhanced gain and a unidirectional radiation pattern, a properly tuned reflector is positioned behind the radiator so that constructive interference of the emitted waves is achieved. Two identical slotted bowtie radiators arranged orthogonally to realize dual-polarized radiation. The orthogonal orientation effectively minimizes field overlap between the radiating elements, which reduces mutual coupling and enhances polarization isolation. Port isolation is further improved by the balanced feed up to 40 dB and 33.5 dB. A metallic reflector is strategically positioned beneath the radiator, and the reflector spacing significantly influences the phase relationship between direct and reflected waves. By effectively optimizing this spacing, we can achieve constructive interference in the broadside direction, which ultimately enhances gain and improves the front-to-back ratio by minimizing backward radiation. Image theory is used to estimate the fundamental distance between the radiator and reflector:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$H\approx \frac{{\lambda}_{0}}{4}$$\end{document}where the free-space wavelength at the lower operating frequency is represented by λ0. Constructive broadside interference is achieved through optimized spacing. A parametric sweep of H demonstrates its impact on impedance matching, gain, isolation, and front-to-back ratio, with an optimal spacing of 28.4 mm yielding improved radiation performance and dual-band operation at 2.52 GHz and 4.42 GHz. The antenna’s dimensions and resonance frequencies can be roughly estimated using the mathematical formulae mentioned above (Table 2).Table 2Design Parameters and Their Influence on Antenna Resonant Characteristics.S. NoParameterControlled Quantity1Bowtie arm lengthLower resonance (2.52 GHz)2Slot lengthUpper resonance (4.42 GHz)3Flare angleDual-band impedance characteristics4Height above reflectorGain & Front-to-Back ratio Table 2Design Parameters and Their Influence on Antenna Resonant Characteristics.S. NoParameterControlled Quantity1Bowtie arm lengthLower resonance (2.52 GHz)2Slot lengthUpper resonance (4.42 GHz)3Flare angleDual-band impedance characteristics4Height above reflectorGain & Front-to-Back ratio Design Parameters and Their Influence on Antenna Resonant Characteristics. Design sensitivity analysis and parametric study A detailed parametric analysis was performed utilizing full-wave electromagnetic simulations to examine the effect of critical geometrical parameters on the impedance response, gain characteristics, and dual-band functionality of the proposed antenna. This study investigates the impact of ground-plane dimensions, reflector spacing, slot tapering, and dielectric substrate properties on antenna design. The findings offer valuable insights into the operating mechanisms and optimization strategies, contributing to a more effective approach to antenna development. Effect of ground size (G) By changing the ground dimensions from 20 to 100 mm, as illustrated in Fig. 11, the impact of ground plane size on antenna gain is investigated. Smaller ground diameters (20 mm to 40 mm) result in poorer gain throughout the operational bands because they do not adequately control backward radiation. Gain and forward radiation are improved by increasing the ground size to 60 mm. Further enlargement to 80 mm and 100 mm only produces a slight improvement; the 100 mm × 100 mm ground plane offers the greatest and most consistent gain. This suggests that a ground size of 100 mm is the best compromise between compactness and gain increment.Fig. 11Comparison of gain versus frequency for different ground plane (G) sizes. Comparison of gain versus frequency for different ground plane (G) sizes. (Plot created by the authors). Trapezoidal slot taper’s effect (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{{W}}}_{{t}{o}{p}}/{{{W}}}_{{b}{o}{t}}$$\end{document}) The influence of trapezoidal slot tapering on the antenna impedance response was investigated by varying the bottom slot width (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${W}_{\mathrm{bottom}}$$\end{document}) while maintaining \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${W}_{\mathrm{top}}=3.5\text{ mm}$$\end{document}, as shown in Fig. 12. Variations in \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${W}_{\mathrm{bottom}}$$\end{document} significantly affected the resonance depth and resonant-frequency locations. A smaller bottom width mainly influenced the lower-frequency resonance, whereas increasing the bottom width improved impedance matching at the upper operating band. These results demonstrate that trapezoidal slot tapering provides an efficient approach for tuning the dual-band response without increasing the overall antenna dimensions.Fig. 12Comparison of S11 versus frequency for different top and bottom slot widths (plot created by the authors). Comparison of S11 versus frequency for different top and bottom slot widths (plot created by the authors). Dielectric substrate impact An examination of the dielectric substrate was conducted to investigate the effect of substrate permittivity on antenna parameters, as depicted in Fig. 13. It was observed that substrates with lower dielectric constants, such as Teflon and Rogers RT5880, shifted the resonant frequencies toward higher-frequency regions, whereas higher-permittivity substrates such as FR4 moved the resonances toward lower frequencies. Enhanced impedance matching was noted for substrates with higher permittivity, with FR4 displaying the most pronounced resonance features. Despite these variations, all investigated substrates maintained dual-band behaviour, indicating that the primary operating mechanism is predominantly governed by the radiator–reflector interaction rather than substrate material alone. Therefore, the dielectric substrate mainly influences frequency tuning and impedance matching characteristics.Fig. 13Comparison of S11 versus frequency for different dielectric materials (plot created by the authors). Comparison of S11 versus frequency for different dielectric materials (plot created by the authors). Effect of reflector spacing (H) A parametric examination of the influence of radiator-reflector spacing (H) on impedance characteristics was conducted by altering the distance from 5 to 30 mm, as depicted in Fig. 14. At smaller spacing values (5–10 mm), strong electromagnetic coupling suppressed the higher-order resonance, resulting in single-band behaviour around 2.5 GHz. As the spacing increased to 15–20 mm, the second resonant mode gradually appeared, indicating the onset of dual-band operation. The achievement of clear dual-band characteristics with enhanced impedance matching was observed at spacing values ranging from 25 to 30 mm. Furthermore, it was noted that as the height (H) increases, the upper resonant frequency shifts toward lower frequencies. This phenomenon can be attributed to variations in the effective current path and the coupling mechanism. The optimum performance was obtained at H = 28.4 mm, where resonances occurred at 2.52 GHz and 4.42 GHz with enhanced impedance matching and stable radiation characteristics.Fig. 14Comparison of S11 versus frequency for different heights (H) between radiator and reflector (plot created by the authors). Comparison of S11 versus frequency for different heights (H) between radiator and reflector (plot created by the authors). Results and discussions A quantitative comparison with dual-polarized bowtie antennas and recent dual-polarized antenna designs is presented in Table 3. The majority of the published studies primarily concentrate on broadband or MIMO configurations. These works frequently incorporate multilayer structures, parasitic elements, or sophisticated feeding networks to improve overall performance. In contrast, the proposed antenna adopts a simple planar slotted bowtie configuration combined with a finite reflector, enabling controlled dual-band operation with high isolation and stable radiation characteristics. The suggested design demonstrates its efficacy for sub-6 GHz multi-service wireless applications by achieving competitive gain, dual-band operation and significantly higher port isolation despite its structural simplicity.Table 3A quantitative comparison between the suggested antenna and dual-polarized bowtie antennas.S. no.Ref.Frequency bandImpedance bandwidth (MHz)Peak gain (dBi)Isolation (dB)Cross-polarization (dB)Feeding method19Single band4606.628–Microstrip feed212Tri band40/100/605.1Low< − 20Microstrip feed313Single band–7.3 > 14< − 16Hybrid coupler feed419Single band1603.21-LowMicrostrip feed522Single band–7 > 20< − 15Microstrip feed626Single band1.84 G8 > 20< − 20Coaxial balun feed730Single band3002.9 > 20< − 153-port feed network8This workDual band 2.52 GHz/4.42 GHz220 MHz/420 MHz7.6/6.6340/33.5− 15.8Balanced coaxial feed– denotes parameters that the cited study does not specifically report. Table 3A quantitative comparison between the suggested antenna and dual-polarized bowtie antennas.S. no.Ref.Frequency bandImpedance bandwidth (MHz)Peak gain (dBi)Isolation (dB)Cross-polarization (dB)Feeding method19Single band4606.628–Microstrip feed212Tri band40/100/605.1Low< − 20Microstrip feed313Single band–7.3 > 14< − 16Hybrid coupler feed419Single band1603.21-LowMicrostrip feed522Single band–7 > 20< − 15Microstrip feed626Single band1.84 G8 > 20< − 20Coaxial balun feed730Single band3002.9 > 20< − 153-port feed network8This workDual band 2.52 GHz/4.42 GHz220 MHz/420 MHz7.6/6.6340/33.5− 15.8Balanced coaxial feed– denotes parameters that the cited study does not specifically report. A quantitative comparison between the suggested antenna and dual-polarized bowtie antennas. – denotes parameters that the cited study does not specifically report. Figures 15 and 16 illustrate the fabricated prototypes under test corresponding to Antennas B and C, respectively.Fig. 15Fabricated Antenna-B device under test (photograph taken by the authors during testing).Fig. 16Fabricated Antenna-C device under test (photograph taken by the authors during testing). Fabricated Antenna-B device under test (photograph taken by the authors during testing). Fabricated Antenna-C device under test (photograph taken by the authors during testing). The proposed antenna was designed and analysed using CST Microwave Studio. The antenna prototype was constructed on an FR4 substrate and subjected to experimental characterization within an anechoic chamber. This process utilized an ANRITSU MS46122B vector network analyser (VNA) to validate the simulated results effectively. The fabricated prototypes of the antenna without reflector (Antenna-B) and proposed antenna (Antenna-C) along with their corresponding measurement setups are shown in Figs. 15 and 16, respectively. The S-parameters, including reflection coefficient (S11) and port isolation (S12), were measured using a VNA after performing appropriate calibration. The radiation characteristics were evaluated under far-field conditions in an anechoic chamber to minimize environmental reflections. During the measurements, a standard horn antenna was used as the transmitting antenna, while the proposed antenna served as the receiving antenna. The separation between the transmitting and receiving antennas was maintained at 2.2 m to satisfy far-field conditions. The antenna under test was mounted on a rotating positioner, and measurements were carried out over 360° to obtain radiation patterns in the principal planes. Impedance characteristics, surface current analysis, and port isolation Figure 17 shows the Antenna-A simulated S11 parameter and Fig. 18 shows the Antenna-B simulated S11 and S22 parameters. At 2.6 GHz, Antenna-A demonstrates good impedance matching. Similarly, the Antenna-B exhibits 10-dB return loss for port-1 at 2.7 GHz and for port-2 at 2.6 GHz, respectively.Fig. 17Simulated S11 of Antenna-A (plots created by the authors).Fig. 18Simulated S11 and S22 of Antenna-B (plots created by the authors). Simulated S11 of Antenna-A (plots created by the authors). Simulated S11 and S22 of Antenna-B (plots created by the authors). Figure 19 depicts the simulated return loss of the suggested antenna (Antenna-C). From the figure, it is observed that Antenna-C exhibits dual-band properties at resonant frequencies 2.52 GHz and 4.42 GHz.Fig. 19Antenna-C simulated S11 versus frequency (Plot created by the authors). Antenna-C simulated S11 versus frequency (Plot created by the authors). The proposed antenna operates at 2.52 GHz and 4.42 GHz. The − 10 dB impedance bandwidth for Port 1 covers both the lower and upper bands, while Port 2 exhibits a dominant resonance in the lower band. The absence of a pronounced higher-order resonance for Port 2 is attributed to the orientation of current distribution and reduced coupling with the reflector under orthogonal excitation conditions. Figures 20 and 21 present the simulated and measured reflection coefficients of Antenna-B, and Fig. 22 displays Antenna-C simulated versus measured reflection coefficients for port 1. Port 2 of Antenna-C demonstrates similar reflection coefficient properties as Port 1. Antenna-B exhibits impedance bandwidths of 439.91 MHz and 385.05 MHz for Ports 1 and 2, respectively. After integrating the reflector, Antenna-C can achieve dual-band operation effectively with impedance bandwidths of 220 MHz and 420 MHz for Port 1 and 270 MHz for Port 2. The measured and simulated reflection coefficients are in good agreement, which validates the structure. The coupling effects in the feeding structure are the cause of the asymmetry between S11 and S22.Fig. 20Antenna-B simulated and measured S11 versus frequency (plot created by the authors).Fig. 21Antenna-B simulated and measured S22 versus frequency (plot created by the authors).Fig. 22Antenna-C simulated and measured S11 versus frequency (plot created by the authors). Antenna-B simulated and measured S11 versus frequency (plot created by the authors). Antenna-B simulated and measured S22 versus frequency (plot created by the authors). Antenna-C simulated and measured S11 versus frequency (plot created by the authors). The introduction of the reflector significantly influences the impedance bandwidth of the antenna. For Antenna-B (without reflector), the − 10 dB bandwidth is approximately 439.91 MHz, corresponding to a fractional bandwidth of about 17.6% at 2.52 GHz. In contrast, for Antenna-C (with reflector), the bandwidth reduces to approximately 220 MHz, resulting in a fractional bandwidth of about 8.7%. This reduction in bandwidth is primarily due to the increased electromagnetic coupling between the radiator and the reflector, which enhances radiation directivity and front-to-back ratio but also leads to stronger resonance confinement. Despite the reduced bandwidth, the antenna maintains adequate coverage for sub-6 GHz wireless applications, where improved gain, high isolation, and stable radiation characteristics are critical. This reflects a typical design trade-off between bandwidth and radiation performance. There is a discernible difference between the measured and simulated values especially in the return-loss magnitude and gain. The main causes of this phenomenon, which is frequently observed in slot-loaded antennas, include fabrication tolerances in the slot geometry, feed-connector parasitics, FR4 substrate property uncertainties, measurement errors pertaining to chamber conditions and antenna alignment could affect the outcomes. Additionally, Large trapezoidal slots and an ideal radiator-to-reflector separation are two features of the suggested antenna that are extremely sensitive to minute dimensional changes. However, the measured findings verify that the antenna meets the impedance matching requirements for realistic wireless applications within the intended frequency bands. While aluminium sheets were utilized for manufacturing because they were more readily available, copper was used to represent the reflector in simulations. Both materials have very little effect on antenna radiation characteristics because of their strong electrical conductivity at sub-6 GHz frequencies. The strong similarity between the measured and simulated results attests to this. Figures 23 and 24 display the S-parameters between the two ports 1 and 2, of Antennas B and C. It is observed from the figure that both the S12 and S21 values are similar. Throughout the specified operational frequency range, the isolation between the two ports consistently exceeds 34 dB and 30.5 dB for Antennas B and C, respectively. Notably, frequencies within the range of 2 GHz to 5 GHz demonstrate port isolation greater than 31 dB.Fig. 23Antenna-B simulated and measured S12 and S21 versus frequency (plot created by the authors).Fig. 24Antenna-C simulated and measured S12 and S21 versus frequency (plot created by the authors). Antenna-B simulated and measured S12 and S21 versus frequency (plot created by the authors). Antenna-C simulated and measured S12 and S21 versus frequency (plot created by the authors). The surface current distributions in Figs. 25, 26, 27, 28, 29 provide insight into the resonant behaviour and polarization characteristics of the proposed antenna. Figures 25 and 26 show the current distributions in both magnitude & vector forms of Antenna-B (without reflector) at approximately 2.6 GHz and 2.7 GHz, corresponding to Port 1 and Port 2 excitations, respectively. In both cases, the current is predominantly distributed along the slotted bowtie arms, forming an effective half-wavelength current path. The presence of trapezoidal slots increases the effective electrical length of the radiator, thereby enabling resonance at lower frequencies relative to the physical dimensions. The symmetric current distribution along the bowtie arms confirms balanced excitation and supports stable radiation behaviour.Fig. 25(a,b) Antenna-B surface current in magnitude form (image generated from simulation tool by the authors).Fig. 26(a,b): Antenna-B surface current in vector form (image generated from simulation tool by the authors).Fig. 27(a,b) Antenna-C surface current at port 1 (2.52 GHz) (image generated from simulation tool by the authors).Fig. 28(a,b) Antenna-C surface current at port 1 (4.42 GHz) (image generated from simulation tool by the authors).Fig. 29(a,b) Antenna-C surface current at port 2 (2.68 GHz) (image generated from simulation tool by the authors). (a,b) Antenna-B surface current in magnitude form (image generated from simulation tool by the authors). (a,b): Antenna-B surface current in vector form (image generated from simulation tool by the authors). (a,b) Antenna-C surface current at port 1 (2.52 GHz) (image generated from simulation tool by the authors). (a,b) Antenna-C surface current at port 1 (4.42 GHz) (image generated from simulation tool by the authors). (a,b) Antenna-C surface current at port 2 (2.68 GHz) (image generated from simulation tool by the authors). Figures 27, 28 and 29 illustrate the current distributions in both magnitude and vector forms of Antenna-C (with reflector) at 2.52 GHz, 4.42 GHz corresponding to Port 1 and 2.68 GHz corresponding to Port 2 excitations, respectively. At the lower frequency, the current distribution remains similar to that of Antenna-B, indicating that the fundamental resonance is governed by the radiator geometry. At the higher frequency (~ 4.42 GHz), the current distribution is significantly altered, with strong currents concentrated along the slot edges and horizontal segments. This behaviour is attributed to the interaction between the radiator and its image currents on the reflector, which modifies the effective current paths and excites a higher-order resonant mode. While the orthogonal arms exhibit phase fluctuations, the current is predominantly concentrated along the horizontal segments and curved slot edges. The interaction between the radiator and the finite reflector modifies the effective current paths, exciting a higher-order resonant mode and redistributing the surface currents. As a result, the antenna exhibits resonance at 4.42 GHz. Notably, reflector coupling is the key mechanism enabling the upper-band resonance, and the current distribution highlights the antenna’s electromagnetic behaviour at this frequency. Furthermore, the orthogonal arrangement of the bowtie elements results in current flow along perpendicular directions for the two ports, corresponding to dual linear polarizations. The balanced feeding structure ensures symmetric current excitation, thereby reducing cross-polarization and contributing to high port isolation. Radiation characteristics Figure 30a,b, respectively, show the simulated radiation patterns for Antenna-C in the E-plane at 2.52 GHz and 4.42 GHz for Port 1. The H-Field pattern for port 1 at 2.52 GHz and 4.42 GHz is shown in Fig. 30c,d. The patterns displayed in Fig. 30a–d are used to further assess the radiation properties of the proposed antenna. The radiation patterns in Fig. 30a (E-plane) and 30(c) (H-plane) show broad, stable main lobes at 2.52 GHz, with half-power beamwidths (HPBW) of approximately 130° and 150°, respectively. The HPBW values at 4.42 GHz are approximately 120° and 115°, respectively, as seen in Fig. 30b (E-plane) and 30(d) (H-plane), signifying a slight beam narrowing due to increased directivity introduced by the reflector. In addition to beamwidth consistency, the antenna maintains a front-to-back ratio exceeding 23 dB across both operating bands, confirming effective suppression of backward radiation. Furthermore, the cross-polarization levels remain below − 15.8 dB in both E & H principal planes, signifying good polarization purity. These quantitative findings verify that the suggested antenna produces stable radiation patterns with low cross-polarization, high—directivity, and consistent beamwidth across the operational frequencies.Fig. 30(a,b) Antenna-C simulated E-field radiation patterns. (c,d) Antenna-C simulated H-field radiation patterns. (a,b) Antenna-C simulated E-field radiation patterns. (c,d) Antenna-C simulated H-field radiation patterns. Figure 31 shows the radiation pattern of simulation and measurement at 2.7 GHz frequency for Antenna-B. Figure 32 and 33 shows the simulated and measured radiation patterns at 2.52 GHz and 4.42 GHz frequencies of Antenna-C. The radiation patterns, of the recommended antenna show minimal variation because of their symmetrical design.Fig. 31Antenna-B simulated and measured radiation pattern at 2.7 GHz (plot created by the authors).Fig. 32Antenna-C simulated and measured radiation pattern at 2.52 GHz (plot created by the authors).Fig. 33Antenna-C simulated and measured radiation pattern at 4.42 GHz (plot created by the authors). Antenna-B simulated and measured radiation pattern at 2.7 GHz (plot created by the authors). Antenna-C simulated and measured radiation pattern at 2.52 GHz (plot created by the authors). Antenna-C simulated and measured radiation pattern at 4.42 GHz (plot created by the authors). Gain, realized gain, and radiation efficiency The gain obtained by Antenna-C and Antenna-B for ports 1 and 2, respectively, is contrasted in Fig. 34a,b. The simulated gain of the Antenna-B approaches 2 dBi, while the measured gain reaches up to 2.1 dBi. The proposed antenna (Antenna-C) shows a simulated gain of 7.63 dBi and 6.638 dBi and a measured gain of 7.8 dBi and 6.9 dBi at the operating frequency bands. This demonstrates a promising alignment between simulation and measurement performance metrics. The proposed Antenna-C provides an average simulated gain of 7.2 dBi, it is clear that adding the reflector significantly increases the gain. The proposed antenna (Antenna-C) shows a much higher gain in the operating frequency bands, when compared to the antenna without the reflector (Antenna-B).Fig. 34(a) Comparison of port 1 gain for Antenna-B and Antenna-C. (b) Comparison of port 2 gain for Antenna-B and Antenna-C (plot created by the authors). Simulated and measured gain of the Antennas B and C. (a) Comparison of port 1 gain for Antenna-B and Antenna-C. (b) Comparison of port 2 gain for Antenna-B and Antenna-C (plot created by the authors). Simulated and measured gain of the Antennas B and C. The comparison of the observed and predicted antenna gain for both orthogonal ports is shown in Fig. 34a,b. The simulated values closely match the measured peak gains of 7.6 dBi at 2.52 GHz and 6.63 dBi at 4.42 GHz. Fabrication tolerances, SMA connector losses, and measurement setup uncertainties are the primary causes of small differences between simulated and measured results. Overall, the findings support the reflector-backed slotted bowtie configuration’s ability to produce consistent and improved gain over the targeted frequency ranges. The Realized Gain (GR) can be calculated using S-parameters (S11) and Gain (G) values from the formula:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{G}}_{{\mathrm{R}}} \left( {{\mathrm{dB}}} \right) \, = {\text{ G}}\left( {{\mathrm{dB}}} \right) + {1}0{\text{ log}}_{{{1}0}} \left( {{1} - \left[ \Gamma \right]^{{2}} } \right)$$\end{document}where, Г is the reflection coefficient. Г = 10(S11/20). Case-1: At port 1, At 2.52 GHz, S11 value is − 12.66 dB, So, Г = 10(− 12.66/20) ≈ 0.233. Hence, the mismatch Loss of the antenna is 10log10(1 − [Γ]2) = 10log10(1–0.2332) ≈ − 0.24 dB. Gain (IEEE) at 2.52 GHz is 7.60 dBi from image 34(a),\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\text{Realized Gain is 7}}.{6}0 - 0.{24} = { 7}.{\text{36 dBi}}$$\end{document} This small difference confirms that the antenna impedance matching is efficient. Case-2: At port 1, At 4.42 GHz, S11 value is − 44 dB, So, Г = 10(-44/20) ≈ 0.0063. Hence, the mismatch Loss of the antenna is 10log10(1 − [Γ]2) = 10log10(1–0.00632). ≈ − 0.00017 dB, Since, the reflection is so low at this frequency 4.42 GHz, the Mismatch Loss is virtually zero (< 0.0002 dB), Gain (IEEE) at 4.42 GHz is 6.64 dBi from image 34(b),\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\text{Realized Gain is 6}}.{64 } - \, 0.000{17 } \approx { 6}.{\text{64 dBi}}$$\end{document} Here, both Gain (IEEE) and Realized Gain will be almost identical (6.64 dBi). Case-3: At port 2, At 2.68 GHz, S11 value is − 12.07 dB, So, Г = 10(− 12.07/20) ≈ 0.249. Hence, the mismatch Loss of the antenna is 10log10(1 − [Γ]2) = 10log10(1–0.2492) ≈ − 0.27 dB. Gain (IEEE) at 2.68 GHz is 7.61 dBi from image 34(c),\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\text{Realized Gain is 7}}.{61} - 0.{27} = { 7}.{\text{34 dBi}}$$\end{document} This small difference confirms that the antenna impedance matching is efficient. Based on the above formulation, the antenna achieves a peak realized gain of approximately 7.36 dBi at 2.52 GHz, 6.64 dBi at 4.42 GHz for port 1 and 7.34 dBi at 2.68 GHz for port 2. These values are consistent with the measured gain performances shown in Fig. 35a–c, which are 7.6 dBi, 6.63 dBi and 7.34 dBi, respectively.Fig. 35(a) Realized gain at 2.52 GHz. (b) Realized gain at 4.42 GHz. (c) Realized gain at 2.68 GHz—Port 2 (image generated from simulation tool by the authors). (a) Realized gain at 2.52 GHz. (b) Realized gain at 4.42 GHz. (c) Realized gain at 2.68 GHz—Port 2 (image generated from simulation tool by the authors). The realized gain of the proposed antenna is assessed to consider the consequences of impedance mismatch. The proximity of the gain and realized gain values suggests that the mismatch loss is minimal, affirming effective power transfer between the feed and the radiator. The negligible disparity between the gain and realized gain (less than 0.28 dB) further substantiates the efficacy of the feeding mechanism and impedance matching, guaranteeing minimal reflection losses and optimal radiation. Figure 36 illustrates the radiation efficiency of the proposed antenna for both ports. The antenna exhibits a radiation efficiency over 95% across the operational bands for both Antenna-B and Antenna-C configurations. The incorporation of the reflector (Antenna-C) yields a modest enhancement and stabilization of efficiency, especially at elevated frequencies, in contrast to the radiator-only scenario (Antenna-B). Additionally, this ensures reliable performance throughout the operating frequency range by validating the use of the chosen substrate and feeding mechanism.Fig. 36Comparison of radiation efficiencies for Antennas B and C (plot created by the authors). Comparison of radiation efficiencies for Antennas B and C (plot created by the authors). Conclusion A dual-band, dual-polarized slotted bowtie antenna has been proposed and experimentally validated and well-suited for sub-6 GHz multi-service wireless systems, such as WLAN, IoT networks, and access-point platforms, particularly in environments where polarization diversity, interference mitigation, high isolation, stable radiation patterns, and dual-polarized operation are essential, such as dense wireless deployments. The antenna employs two orthogonally arranged slotted bowtie dipoles with a balanced feeding structure, along with a finite 100 mm × 100 mm metallic reflector to enhance radiation performance and enable dual-band operation. The proposed antenna achieves resonances at 2.52 GHz and 4.42 GHz, with high port isolation (40 dB and 33.5 dB), maintains cross-polarization levels below − 15.8 dB, and a front-to-back ratio exceeding 23 dB. The incorporation of the reflector significantly improves the antenna gain from approximately 2 dBi to a peak value of 7.6 dBi, while maintaining stable radiation characteristics. The outcomes verify that the proposed design provides a successful trade-off between dual-band operation, performance, and simplicity, making it suitable for practical sub-6 GHz wireless communication systems.