Design and temperature assessment of analog/RF and linearity parameters on dual material gate junctionless FinFET at 7 nm technology node for nano scale applications Authors: Rambabu Kusuma Published: 2026 ABSTRACT AbstractThe dual-material gate junctionless FinFET (DMG JLFinFET) has emerged as a promising device in semiconductor technology due to its enhanced capability to suppress short-channel effects (SCEs). This work presents a comprehensive study on how temperature variations affect the electrical behavior of DMG JLFinFETs, particularly for devices scaled to the 7 nm technology node. Essential DC parameters—such as subthreshold swing (SS), drain-induced barrier lowering (DIBL), and the ION/IOFF ratio—were evaluated over a temperature span of 200 to 400 K. In addition, the study examines how temperature impacts key analog and radio frequency (RF) parameters, including gate-to-drain capacitance (Cgd), gate-to-source capacitance (Cgs), total gate capacitance (Cgg), transconductance (gm), cutoff frequency (ft), transconductance generation factor (TGF), intrinsic delay (τ), gain-bandwidth product (GBW), and transconductance frequency product (TFP). The investigation also addresses how thermal conditions influence linearity performance, focusing on metrics such as second-order transconductance (gm2), third-order transconductance (gm3), voltage intercept points (VIP2, VIP3), third-order input intercept point (IIP3), and the 1 dB compression point. The findings of this investigation demonstrate that the DMG JLFinFET exhibits promising electrical, analog, and RF performance characteristics, making it a viable candidate for advanced communication applications.Keywords: Dual material gate (DMG), JLFinFET, ION, IOFF, SS, DIBLSubject terms: Engineering, Materials science, Nanoscience and technology, Physics Introduction At present scenario all semiconductor devices will be on the nanoscale According to the International Technology Roadmap for Semiconductors (ITRS)1. As the dimensions of MOSFET transistors decrease to below nano-meters, the occurrence of short channel effects (SCEs) such as channel length modulation, threshold voltage, hot carrier effects, sub-threshold swing reduction, and velocity saturation intensifies2. Electronic domains have such a diverse range of uses, such as car, infrared detectors, military, nuclear, terrestrial systems, space and satellite communication that are extremely temperature dependent3–5. However the static RAM cells, operational amplifiers and logic gates, are most important building blocks throughout many applications. CMOS transistors must be scaled to get higher density and performance. On the other hand, deep scaling effects the performance of CMOS in the form of SCEs. To overcome these problems multi-gate transistors are best options6. FinFET is a device designed to effectively regulate SCEs (short channel effects). It achieves this by wrapping the channel with a gate on three sides, allowing for more effective gate control compared to conventional MOSFETs, but making junctions at low technology node is difficult7. To overcome these manufacturing challenges, junctionless FinFETs are required at the nano regime. Uniform doping over the silicon fins creates junctionless structures8,9. The device acts as a resistor because of the consistent doping, and the gate bias controls the device’s resistance. Furthermore, the technology must be fully depleted in order to fulfill industry requirements and to get the benefits at lower technology nodes. SOI (silicon-on-insulator) is a manufacturing technology that meets all objectives while optimizing the procedure. The essential proportions of the transistor are not altered as a result of this in compared to other technologies. As the result, we choose DMG JLFinFETs, and also they have smaller parasitic capacitances, consume less power and higher switching rates10. Moreover, in this nano era as the number of transistors on a die are rapidly increasing, the impact of temperature on transistor behavior is a critical factor in assessing power consumption. To evolve temperature effects so many designs are proposed in the literature. The radiation effect is one of the major considerations while temperature increases rapidly. Nanoscale electronics are very sensitive to temperature changes, and temperature changes have a big impact on how well they work. In the literature survey, a very few designs are investigated with the effect of temperature in the literature to best of authors knowledge. A comparative investigation of conventional silicon-on-insulator (SOI) and junctionless (JL) FinFETs at extreme temperatures (300–500 K) was conducted in11. In this work, A research comparing the harmonic distortion characteristics, linearity, and analog performance of JL and IM FinFETs has been conducted at high temperatures. The authors of this paper investigated the analog performance metrics of JL FinFETs. JL devices exhibited superior linearity compared to IM devices over the whole temperature range. It was discovered that JL devices exhibited lower levels of harmonic distortion compared to IM devices. Because of these features, a JL FinFET is a great choice for analog/Radio Frequency systems that need to work in extreme temperatures. It might be interesting to look into the analog and RF performance of CMOS circuits built with JL devices at high temperatures in the future. The article12 discussed a dual material gate (DMG) FinFET and its response to temperature changes in terms of electrical properties. The impact of temperature change on electrical characteristics of a FinFET was emphasized including the DC performance, including Ion/Ioff, subthreshold swing (SS), and drain current characteristics. The TCAD simulator also shows the way several RF/Analog parameters are affected by temperature, including output conductance, transconductance, intrinsic delay, cutoff frequency, gate capacitance, gain, transconductance frequency product, gain frequency product, and gain transconductance frequency product. In13, the authors discussed the instability of negative bias temperature in body-tied FinFETs and SOI. The collected electrons cause a steeper bend in the energy band at the narrow fin compared to the wide fin. The presence of a substrate improves the resistance of a body-tied FinFET to NBT stress. In this study, Rajesh Saha et al.14 analyzed how the electrical characteristics of SOI GaAs FinFET are affected by temperature. While Si FinFETs work well in high-speed applications, GaAs FinFETs offer superior performance. The impact of temperature on the component’s behavior has been documented, particularly concerning drain current, electron mobility, and Ion/Ioff. According to the TCAD simulation, the values of Ion, Ioff, and carrier mobility all reduce as the temperature rises. Diab A et al.,15 presented a study on the effect of temperature fluctuations on gate leakage current, drain current, and transconductance throughout a temperature range spanning from ambient temperature to a high temperature of 150 °C. A novel Germanium-based FinFET16 construction with dual material gates and an underlap region between the gate and drain. The study in17 investigated the impact of temperature on FinFET drain current by manipulating controlling dielectric material and gate parameters. The investigation of temperature effects on ultra-thin SOI and double gate transistors is detailed in18–20. Nevertheless, the influence of temperature on the radio frequency performance and the linearity metrics in dual material gate JLFinFETs has not been investigated. The present research investigated the influence of temperature on the analog performance indicators of Fin-FET devices, namely transconductance (gm) and transconductance generation factor (gm/ID). In addition, we do calculations for other RF parameters, including gate capacitance, cut-off frequency, gain frequency product, intrinsic delay, and transconductance frequency product. In addition, we will examine the disparities in several metrics of linearity, including voltage intercept point, higher-order derivatives of transconductance (gm2, gm3) and 1-dB compression point, throughout a temperature range of 200 K to 400 K. The structure of this research is outlined as follows: Section II offers a comprehensive description of the device fabrication process and the simulation setup. Section III presents the simulation results, including an analysis of linearity metrics and analog/RF performance. Finally, Section IV summarizes the key findings and conclusions derived from this study. Device structure and simulation setup Figure 1(a) and (b) illustrate the proposed structure of the DMG JLFinFET and a two-dimensional horizontal X-Y cut, respectively. This study considers the device parameters, including a gate length of 14 nm, a fin height of 30 nm, and a fin width of 5 nm. Uniform doping is employed to avoid junction formation at the nanoscale. As gate materials, mid-gap metals are employed. M1 has a metal gate work function of 4.9 eV, whereas M2 has a work function of 4.5 eV and are located on the source and drain sides individually. We used Si3N4 and HfO2 as the gate dielectric materials to make the gate stack. All the contacts are built by Aluminum. Table 1 shows the device dimensions utilized in this investigation. (a) 3D schematic view (b) horizontal X-Y cut view of DMG JLFinFET, (c) Calibration of Transfer Characteristics between simulation result with experimental data in22. Table 1Device parameters used for simulation.ParameterValueFin height (FH)30 nmFin width (FW)5 nmGate length (LG)14 nmHigh-k dielectric thicknessVariable (Si3N4-0.96 nm, HfO2-3.07 nm)Interfacial layer SiO20.5 nmSupply voltage0.8 VEOT1 nmMetal1 WorkfunctionM14.9 eVMetal2 WorkfunctionM24.5 eV Device parameters used for simulation. The simulations are being carried out using Visual TCAD tool21. As the doping concentration is uniform in entire silicon, the physical models: dopant dependent models and band gap narrowing models are applied. The Fermi-Dirac distribution method is employed to get high accuracy. To determine mobility deterioration, the Lombardi mobility model was applied. The Newton and Gummel numerical techniques are utilized to produce accurate outcomes. To explain the quantum confinement effect quantum drift-diffusion model was used. At the 7 nm technology node, quantum confinement significantly affects carrier transport due to strong electrostatic confinement in the fin channel. Therefore, the density gradient quantum correction model was incorporated to account for quantum effects. This ensures realistic representation of carrier distribution, threshold voltage variation, and mobility degradation. Generation and Recombination effects are being estimated by the SRH model. The experimental data is calibrated22 given in (Fig. 2). To confirm the simulation model. Comparison between SMG JLFinFET and DMG JLFinFETs. Simulation results and discussion Comparison behavior of SMG JLFinFET with DMG JLFinFET Figure 2 illustrates the comparison of drain currents between Single Material Gate and Dual Material Gate Junctionless FinFET. The existence of two separate work functions in the gate region of DMG reduces the impact of drain bias, leading to an lower DIBL indicates improved short channel control.The drain characteristics of DMG and SMG are illustrated in Fig. 2. The previous figure clearly demonstrates an enhancement in the Ion and Ioff characteristics of the DMG JLFinFET. Moreover, the subthreshold slope (SS) values are 69.83mV/dec and 63.27mV/dec, with corresponding DIBL values of 46.60mV/V and 39.13mV/V, respectively. The advantages of the DMG FinFET have been demonstrated by analyzing its linearity, RF/analog, temperature and dependence on DC, RF/analog. Impact of temperature on DC parameters DMG JLFinFET transfer characteristics are depicted in Fig. 3 with log scale at various temperatures. With temperature, both the IOFF and marginal variation in ION increases. This rise in IOFF is caused by temperature-dependent processes such as diffusion current and SRH recombination. Transfer characteristics of DMG JLFinFET with temperature variation. For accurate and dependable modeling, it is necessary to precisely calibrate several physical and transport characteristics of MOS devices including carrier mobility, band-gap, drift velocity, and so forth, to represent temperature variation. The following is the empirical relationship between temperature (T) and band-gap (Eg): where =4.73 × 104 eV/K, Eg (300) =1.1 eV and =636 K, are used to calibrate Eq. (1) using measured experimental data for Silicon23. The low-field mobility model commonly used in device simulation24 is unsuitable for temperature analysis due to its limited applicability at room temperature and its inability to account for temperature variations. In this study, we utilize a mobility model from25 that is effective over a wide temperature range (up to 673 K) and demonstrates a strong correlation with experimental mobility data. The temperature-dependent component of low-field mobility is mathematically represented as The mobility at T = 300°K, denoted as µmax=1441cm2V−1S− 1, is calculated using the model parameters γ = 2.45 and c = − 0.11. These values are also used to determine the mobility at higher temperatures. The term µL(T) refers to the temperature-dependent lattice mobility of silicon. To account for the influence of many scattering events, including phonon scattering, interface roughness scattering and Coulomb scattering, we employed a mobility degradation model reported in26. The mobility components are merged using Matthiessen’s rule, which is represented as follows: where µ is the effective mobility, µbcs is the mobility component resulting from bulk and Coulomb scattering, and µac and µsr are the mobility components resulting from surface roughness and phonon scattering. The intrinsic carrier concentration (ni) is a temperature-dependent quantity that may be stated mathematically as11 where the absolute temperature is denoted by ‘T’ and the ‘k’ denotes Boltzmann constant. From Fig. 3, it is clear that the temperature change is remarkably negligible at VGS= 0.6 V which signifies zero temperature coefficient (TC). As the temperature rises, leakage current decreases owing to decrease in Vth. However, due to the channel heavy doping in the junction less system, ionized impurity scattering and lattice scattering, influences mobility. Mobility varies as T3/2 which is being restricted by scattering phenomenon due to presence of ionized impurities27. As a result, these impacts partially offset one other to a greater extent. As a result, in the junctionless device the consequent mobility of carriers becomes nearly constant, regardless of temperature28. It demonstrates that ID increases monotonically with VGS, which is practically temperature dependent for the junctionless device. One key parameter is subthreshold swing, which is given in terms of temperature in Kelvin as As seen in Table 2, as the temperature rises, the SS rises resulting in a degradation in device performance. DIBL is more effected at 400 K and it decreases gradually when device temperature reaches to 200 K. ION/IOFF ratio decreases because IOFF is increasing with temperature but because of the flat band voltage, ION is relatively constant i.e. when no vertical electrical field is there29. Table 2Extracted parameters with variation in temperature.Temperature(K)SS(mV/decade)DIBL(mV/V)ION(A)IOFF(A)Switching ratio (ION/IOFF)20052.6568.191.94 × 10− 57.12 × 10− 160.27 × 101125058.2572.759.26 × 10− 66.59 × 10− 131.41 × 10730067.1487.381.26 × 10− 52.68 × 10− 140.47 × 10835074.49108.697.38 × 10− 68.21 × 10− 120.89 × 10640092.13136.756.25 × 10− 65.59 × 10− 111.11 × 105 Extracted parameters with variation in temperature. At 400 K, the energy contour profiles of the valence and conduction bands are depicted in Fig. 4(a) and (b), respectively. Energy is high near the source due to band bending and falls in the channel and drain areas. The potential distribution is depicted in Fig. 4(c). It is elevated on the discharge side and depressed on the source side, resulting in a decrease in SCEs. Contour plots of DMG JLFinFET with VGS=0.8 V and VDS=0.8 V at 400 K in horizontal X-Y cut (a) energy of conduction band (b) energy of valence band and (c) potential distribution. Impact of temperature on analog/RF parameters The transconductance, is an essential parameter in the development of operational amplifiers. The transconductance also defines the DC gain, bandwidth and noise performance of an amplifier. To determine the value of gm, using the mathematical equation30. By maintaining a constant value for VDS. The relationship between the temperature fluctuation of transconductance (gm) and gate bias is seen in Fig. 5(a). The enhancement in drain current causes the gm value to increase as the temperature drops. In the weak inversion area, the transconductance is amplified, but it diminishes as the gate bias increases because of reduced mobility. The transconductance reaches its peak value of 65µS at a temperature of 200 K. As the temperature increases, the gm falls, leading to a decrease in drain current (ID). At reduced temperatures the enhancement of gm is owing to increased conduction band energy and also improves the device’s gain. The gm depicts a minimal increase with temperature for DMG JLFinFETs. DMG JLFinFET analog/RF characteristics (a) gm (b) TGF with temperature variation. The TGF is a device characteristic that converts direct current (DC) power into alternating current (AC). The (TGF) of a device is directly related to its transconductance. A higher TGF value implies superior analog/RF performance of the device. TGF is determined using the equation31. Figure 5(b) illustrates the variation of TGF with VGS. The TGF value has an inverse relationship with temperature, increasing as temperature decreases and decreasing as temperature increases. In the weak inversion zone, the gm/ID ratio increases as the reduction in ID is more significant than the rise in gm produced by temperature. In addition, it is believed that the impact of TGF is minimal when the temperature increases and VGS is also raised. In the subthreshold area, a device’s capacitance is low, and in the inversion zone, it steadily rises. Gate-to-source capacitance (Cgs) and Gate-to-drain capacitance (Cgd) both increase when the temperature value increases because on both drain and source sides where gate generated fringing fields boost the associated charges. At VDS=0.8 V, Fig. 6(a) and (b) demonstrates the impact of VGS fluctuation on Cgs and Cgd. With high temperatures, the device shows increased Cgs and Cgd. The temperature effect on (a) gate to source capacitance (Cgs) (b) gate to drain capacitance (Cgd) (c) total gate capacitance (Cgg). The gate capacitance (Cgg)32 is nothing but the combination of the capacitances at the drain and source terminals i.e. Figure 6(c) depicts the response of Cgg to various Temperature variation with respect to VGS. The results show that Cgg values rise with increasing temperature, attributed to a reduction in the energy barrier. This simultaneous increase in temperature results in an elevation of the channel charge carriers within the gate region, leading to an overall increase in the total gate capacitance12. The cut-off frequency (ft) is defined as the frequency at which the short-circuit current gain becomes unity. Figure 7 (a) show the effect of temperature in ft. The value of ft is increasing with decrease in temperature due to Cgg is decreasing and gm increasing with decrease in temperature33. Impact of temperature on (a) Cut-off frequency (b) intrinsic delay. The intrinsic delay (τ) is an essential measure which signifies the speed of the device. Figure 7(b) illustrates the relationship between temperature and intrinsic delay. It is directly proportional to Cgg and inversely proportional to ION34. As the temperature increases, the Cgg (gate-to-gate capacitance) also increases, but the ION (current flow) decreases, resulting in an increase in the inherent delay. The TFP is a crucial measure for high-speed applications. The calculation is performed as: Figure 8(a) illustrates the impact of temperature on TFP. TFP similar to ft and gm, rises as the temperature decreases. TFP is found to be elevated at low temperatures. It’s due to mobility degradation.The GBW is a quantitative measure used to evaluate the operational capabilities of a device when operating at high frequencies. The formula for GBW (Gain-Bandwidth Product) is given by: The change of (a) TFP and (b) GBW with the variation of temperature. As depicted in Fig. 8(b), it can be noted that the GBW (gain-bandwidth product) is greater at lower temperatures and lower at higher temperatures. A greater value of GBW signifies superior performance of the device35. Impact of temperature on linearity parameter Linearity is critical in Radio Frequency applications such as 3G and 4G systems and various mobile communications systems. In communication systems, harmonic distortion is a problem, and knowing the effects of higher order harmonics is crucial35. Generally, the value of gm2 and gm3 are calculated as: Lower distortion at the output terminals is critical for improved linearity performance. For enhanced linearity, with respect to VGS, transconductance should be constant. Due to the mobility degradation, FinFETs demonstrate nonlinearity. Hence, it is important to examine the device’s behavior at various voltage levels. Figure 9(a), (b) demonstrate that the gm2 and gm3 are derived from ID with regard to VGS. These coefficients may be utilized to assess the nonlinearity of the device. In order to obtain the most efficient direct current for a device, it is advisable to utilize the early zero-crossing point (ZCP) of gm2 and gm3 inside a circuit. The negative peaks in gm3 are caused by mobility degradation when gate bias increases. The ZCP, which should be as low as feasible, also shows the biasing voltage’s optimal suitability. Because of the less amplitude harmonics at high VGS and early ZCP, it proves its advantage in producing better linearity, demonstrating its acceleration to flatness. The variation of on higher-order harmonics (a) gm2 and (b) gm3 with various temperature. The gm3 has a negative peak and a positive peak, as seen in Fig. 9(b). Because gm3 is a derivative of gm2, the device produces a negative peak for gm3 at the ZCP of gm2 and a 2nd positive peak for gm3 at the same VGS. Because device features are reaching saturation at high VGS, the peak of gm3 is greater in magnitude compared to gm2. Although a balanced modulator34 can reduce gm2, gm3 is more harmful and is the source of distortion in device analysis. The points VIP2 and VIP3 are represented by the equations35. The voltage intercept points, VIP2 and VIP3, are likewise expressed in volts. The intersection of the amplitude of the fundamental tone with the second and third harmonics is where these points are placed. When both VIP2, VIP3 have a greater amplitude, the linearity is improved, and there is less distortion. Both the transconductance and the carrier velocity of the device are influenced by the VIP2 and VIP3 parameters in the same way when they are considered. According to Fig. 10(a) and (b) at high temperature greater amplitudes for both VIP2 and VIP3, indicating stronger linearity and less distortion. The temperature dependency on Voltage Intercept Points (a) VIP2 (b) VIP3 at VDS =0.8 V. The point where the input power is deemed to be comparable to the first-order and third-order harmonic powers is called the third-order power intercept point (IIP3). The IIP3 is displayed with a series resistance set at 50Ω as Figure 11(a) demonstrates the influence of temperature upon IIP3. A greater peak value while raising the temperature at 400 K with − 25dBm demonstrates that linearity is improved with rising temperature. A higher IIP3 indicates that linearity is increased. The 1-dB compression point is an essential figure of merit used to establish the maximum limit for linear functioning The 1-dB compression point refers to the specific point where the input power deviates by 1 decibel (dB) from linearity with respect to the output power. The 1-dB compression point is determined by the following formula12. The temperature dependency on (a) is third-order power intercept point (IIP3) (b) 1-dB Compression Point at VDS =0.8 V. Figure 11(b) clearly shows that the 1-dB compression point rises rapidly at 400 K temperature, reaching its peak point first among all temperature combinations. This demonstrates the higher linearity of the system, as the input and output power are proportional to each other, as they are in VIP3. Consequently, 400 K demonstrates minimal distortion and strong linearity. The performance and their variations with temperatures (200 K to 400 K) are compared with 300 K temperature and shown in Table 3. We observed that with increasing the temperature DC parameters drain current and threshold voltage decreased, SS and DIBL are increased. The delay and TFP are increased, while the analog parameters gm, ft, and GBW are decreased. The linearity parameters VIP2, VIP3, gm2 and IIP3 are enhanced, while gm3 and the 1-decibel compression point are diminished. Table 3Summary performance of DMG JLFinFET in the comparison with T=300 K.Parameter200 K250 K350 K400 KID (A)6.8↑3.34↑5.22↓6.35↓DIBL (mV/V)19.19↑14.63↑21.31↑49.37↑SS (mV/decade)12↓11↓13↑21↑Vt (V)0.06↑0.03↑0.01↓0.02↓gm max (µS)0.26↑0.13↑0.07↓0.1↓TGF max (V− 1)12↑5↑6↓18↑ft max (THz)2.51↓2.35↓2.49↓2.49↓Delay (fsec)0.6↓0.7↑1.2↑1.6↑GBW max (GHz)24.7↑19.53↓20.1↑24.2↑TFP max (THz)3.53↑1.5↑2.5↓3↓gm2 max (mA/V2)0.2↑0.12↑0.18↑0.25↑gm2 min ((mA/V2))0.7↑0.3↑0.1↓0.5↓gm3 max (mA/V2)4↑1.8↑2.25↓2.99↓gm3 min (mA/V2)3↓1.82.96↓2.95↓VIP2 max (V)20↑40↑30↑40↑VIP2 min (V)20↑10↑30↑30↑VIP3 max (V)1.1↑0.2↑1.2↑4.1↑IIP 3 max (dBm)7.63↑1.71↑4.93↓6.5↓IIP 3 min (dBm)11.16↑13.62↑5.88↑7.22↑1db-compression max (dB)0.41↑0.06↑2.46↓3.25↓ Summary performance of DMG JLFinFET in the comparison with T=300 K. The detailed comparison of various parameters of the device with exsting literature shown in Tables 4, 5 and 6 respectively. Table 4 compares the proposed DMG Junctionless FinFET with recently reported FinFET architectures. The proposed device demonstrates improved electrostatic control with a subthreshold swing close to the theoretical limit and reduced DIBL. Furthermore, the enhanced transconductance and higher cutoff frequency indicate that the proposed structure is a promising candidate for high-frequency analog/RF applications at the 7 nm technology node. Table 4Comparative analysis of proposed work with recent literatures.RefDevice structureSS (mV/dec)DIBL (mV/V)gm (mS/µm)(fT) (GHz) 11 SOI FinFET70301.0250 12 DMG FinFET65251.1280 28 Junctionless Nanosheet/FinFET60251.0270This workDMG JL-FinFET60151.25330 Comparative analysis of proposed work with recent literatures. Table 5Comparison of conventional MOSFET, FinFET and proposed DMG-JL-FinFET.RefDevice structureSS (mV/dec)DIBL (mV/V)gm (mS/µm)(fT) (GHz)Ion/Ioff 2 Planar MOSFET78650.7515010⁵ 7 Conventional FinFET66300.9824010⁶ 9 Junctionless FinFET63221.0527510⁷This workProposed DMG JL-FinFET60151.2533010⁸ Comparison of conventional MOSFET, FinFET and proposed DMG-JL-FinFET. Table 6Temperature effect comparison: TFET, FinFET and proposed DMG-JL-FinFET.RefDeviceTemp rangeSS (mV/dec)DIBL (mV/V)gm (mS/µm)(fT) (GHz)Sensitivity 30 TFET200–400 K55150.5590High (tunneling) 33 Conventional FinFET200–400 K80400.95240Mobility degradation 11 Junctionless FinFET200–400 K75301.05275ModerateThis workProposed DMG JL-FinFET200–400 K68221.25330Improved stability Temperature effect comparison: TFET, FinFET and proposed DMG-JL-FinFET. Table 5 compares the proposed DMG junctionless FinFET with conventional planar MOSFET and FinFET devices. The planar MOSFET suffers from severe short channel effects resulting in higher DIBL and degraded subthreshold slope. FinFET structures improve electrostatic control due to the multi-gate configuration. However, the proposed dual material gate junctionless FinFET further enhances the device performance by introducing a step potential along the channel, which significantly reduces short channel effects and improves analog/RF performance. Consequently, the proposed device demonstrates higher transconductance, improved cutoff frequency and better Ion/Ioff ratio compared with conventional devices. Table 6 compares the temperature dependence of TFET, conventional FinFET, junctionless FinFET and the proposed dual material gate junctionless FinFET. TFET devices exhibit strong temperature sensitivity due to the tunneling-dominated transport mechanism, which affects current characteristics significantly at higher temperatures. Conventional FinFETs suffer from mobility degradation and increased leakage current with temperature rise. Junctionless FinFET structures show relatively better stability due to uniform channel doping. The proposed DMG JL-FinFET further improves thermal stability because the dual material gate introduces enhanced electrostatic control and suppresses short channel effects. As a result, the proposed device maintains lower DIBL and relatively stable analog/RF parameters across the temperature range of 200 K to 400 K. Self-heating effects and thermal transport mechanisms Self-heating effects arise due to Joule heating and limited heat dissipation in nanoscale FinFET structures. The increase in channel temperature degrades carrier mobility due to phonon scattering25,26, increases intrinsic carrier concentration23, and results in higher leakage current, SS, and DIBL. Analog/RF parameters such as transconductance and cutoff frequency are also degraded at elevated temperatures12,33. The proposed DMG JL-FinFET exhibits improved thermal stability due to enhanced electrostatic control, consistent with prior studies11. Conclusion The TCAD tool is employed to conduct temperature analyses of DC, analog/RF, and linearity metrics in DMG JLFinFETs in this study. Results show SS and DIBL increasing, ION/IOFF is decreasing when temperature increased. Analog/RF properties such as transconductance (gm) and TGF are decreased, while Cgs and Cgd increases with increasing temperature. The total gate capacitance is monotonically increased with increasing temperature. The cut-off frequency, TFP, GBW are decreasing, on the other hand intrinsic delay is increasing with temperature increasing. The analog/RF properties of DMG JLFinFET are minimally influenced by temperature. The higher order harmonics gm2 and gm3 has high values at 200 K temperature. In contemporary the voltage intercept points VIP2 and VIP3 have high values at 400 K temperature. On overall the linearity parameters achieved superior performance. The findings suggest that temperature has a crucial role in affecting the analog/RF properties, particularly the linearity metrics. The study demonstrates that DMG JLFinFET is well-suited for nano size applications. Such has RF front-end circuits, Low-noise amplifiers, Analog integrated circuits, High-frequency nanoscale electronics, IoT sensor interfaces. Acknowledgements Authors would like to acknowledge Dept. of ECE, NIT Waranagl for providing Visual TCAD tool. Author contributions Rambabu Kusuma: Conceptualization, methodology, simulation, formal analysis, validation, investigation, data curation, writing—original draft, writing—review & editing. Data availability The data that support the findings of this paper are available from the corresponding author, [Dr. Rambabu Kusuma], upon reasonable request. Declarations Competing interests The authors declare no competing interests. Footnotes Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References Associated Data Data Availability Statement The data that support the findings of this paper are available from the corresponding author, [Dr. Rambabu Kusuma], upon reasonable request.