A deterministic platform for engineering interfacial phenomena in porous media using artificially structured rough surfaces Authors: Saeed Golshokooh, Mohammad Simjoo, Mohammad Chahardowli Published: 2026 ABSTRACT The role of surface roughness in controlling interfacial phenomena is ubiquitous across natural and engineered porous media, governing core processes in energy recovery, carbon sequestration, and water purification. However, a mechanistic understanding has been hindered by the inability to systematically control and replicate complex surface topographies in the laboratory. Here, we introduce a versatile materials platform that offers deterministic control over surface roughness in these media. Our approach is based on the thermal sintering of glass beads into artificial thin sections, combined with an innovative semi-immersion technique that enables precise sectioning and reliable interfacial measurements. We establish quantitative scaling laws, demonstrating that bead size directly determines roughness amplitude and morphology—from fine, high-frequency textures to pronounced, wavy undulations. This controlled topography sets wettability states, triggering transitions between Wenzel and Cassie-Baxter regimes, and governs contact-line pinning that leads to hysteresis and capillary trapping. By bridging the gap between stochastic natural surfaces and idealized models, our tunable and reproducible platform paves the way for systematic study and tailored engineering of multiphase flow across a wide range of applications, from subsurface hydrology to advanced material design. Introduction The interaction of fluids with solid surfaces is a cornerstone of science and technology, underlying processes as diverse as geological carbon sequestration, water purification, energy recovery, and the function of biological tissue1,2. In all these systems, surface roughness is not a mere artifact but a fundamental state variable that governs wettability, capillary forces, and the dynamics of multiphase flow3,4. Its influence is pervasive: it can control the fate of environmental contaminants5, affects seismic wave propagation and mechanical characterization of rocks6,7, dictate the efficiency of heat and mass transfer8, also modifies relative permeability by reshaping flow pathways and redistributing wetting phase occupancy9,10, and enhance capillary trapping to secure subsurface CO₂11–15. The classical wetting theories of Wenzel and Cassie–Baxter established that surface roughness amplifies intrinsic wettability16,17. However, modern pore-scale research has revealed that these macroscopic descriptions often fail to capture the complex, dynamic interplay between micro-topography and fluid interfaces, which controls contact-line pinning, hysteretic behavior, and ultimate trapping efficiency18–21. Recent experimental and numerical investigations further underscore this complexity: pore-scale imaging has shown how roughness and mineral heterogeneity regulate interfacial configurations and trapping mechanisms in natural porous media22, while controlled wetting experiments demonstrate that roughness-driven variations in contact angle and capillary behavior directly impact displacement dynamics23. Complementary studies in porous transport also highlight that surface topography fundamentally mediates wetting states and phase distribution during multiphase flow24. Despite these advances, significant gaps remain. Experimental science lacks a foundational tool: the ability to systematically engineer and reproducibly characterize well-defined roughness in a porous architecture. Current methodologies rely on naturally occurring rocks, which are intrinsically variable and irreproducible, or on simplified analogues like sandpaper, which lack the morphological fidelity of a connected porous network25,26. This fundamental limitation prevents the establishment of causative, rather than correlative, links between specific topographic features and macroscopic fluid behavior, hindering predictive model development across multiple disciplines. Here, we introduce a materials platform that bridges this critical gap. We present a fabrication and characterization framework for creating artificial porous thin sections with deterministically controlled surface roughness. The core of our approach is the thermal sintering of monodisperse glass beads, which allows us to programmatically tune both the amplitude and morphology of surface topography by varying the bead size. A key innovation within this platform is a novel semi-immersion technique that acts as a capillary barrier during preparation, solving the long-standing experimental challenge of performing reliable contact-angle measurements on rough, permeable surfaces. We quantitatively deconvolve the relationship between particle size and a suite of roughness parameters (e.g., Rₐ, r), establishing robust scaling laws. We then demonstrate the power of this platform by mechanistically probing how defined roughness scales govern wettability transitions and droplet infiltration dynamics. By providing a versatile and reproducible testbed, our work moves the study of interfacial phenomena in porous media from observation to control, offering new pathways to tailor fluid behavior for applications ranging from subsurface engineering to the design of functional porous materials. Experimental setup Accurate contact angle and wettability measurements in reservoir rocks require thin sections that preserve the native surface morphology of mineral grains. Conventional methods involving mechanical slicing of core plugs often disrupt the intrinsic roughness and microstructure of rock surfaces, potentially leading to significant errors in wettability characterization27. To address this limitation, the present study introduces a synthetic thin section methodology using glass beads of varying sizes and geometries. This approach maintains the natural surface topography and better reflects reservoir-like conditions during fluid–solid interaction assessments. The need for such precision becomes especially critical in geologic contexts where tectonic deformation, stratigraphic shifts, or diagenetic mineralization significantly enhance surface heterogeneity. Fabricated through thermal sintering, these synthetic sections provide a controlled, reproducible platform for evaluating wettability and contact angle behavior under realistic surface roughness scenarios. Fabrication of synthetic thin sections via thermal treatment and sintering To replicate the natural surface morphology of reservoir rocks while maintaining experimental control, synthetic thin sections were fabricated using a thermal sintering method. Glass beads were heated to their softening point (~ 685–700 °C), at which edges transitioned into a semi-solid state, enabling partial fusion between adjacent particles28,29. Upon controlled cooling, the fused beads solidified into a coherent porous structure—thereby forming a synthetic thin section (Fig. 1). This approach offers improved reproducibility and surface integrity over conventional mechanical slicing. Pottery clay was used as the mold medium due to its high plasticity, thermal resistance, and chemical inertness during sintering. A 5 mm layer of clay was uniformly spread on a polished refractory plate to create a smooth base. Circular molds (1 cm and 1.5 cm in diameter) were then impressed into the clay. Glass beads of various geometries and sizes were poured into the cavities, followed by gentle mechanical vibration to ensure uniform packing and minimize void spaces. The filled molds were subjected to a controlled sintering cycle:Heating from room temperature to 300 °C in 30 minFurther heating to 695 °C, over 200 minHolding at 695 °C for 10–20 min to allow fusionControlled cooling over 10–12 h to room temperature inside a closed furnaceFig. 1Schematic of the materials and equipment used for fabricating synthetic thin sections via thermal heating and sintering of glass beads. 1) Refractory plate, 2) Spreading pottery clay over the polished refractory plate, 3) Smoothing the pottery clay, 4) Press molding on the refractory plate, 5) Sprinkling glass beads into the molds, 6) Demolding the samples, and 7) Synthetic thin section sample. Heating from room temperature to 300 °C in 30 min Heating from room temperature to 300 °C in 30 min Further heating to 695 °C, over 200 min Further heating to 695 °C, over 200 min Holding at 695 °C for 10–20 min to allow fusion Holding at 695 °C for 10–20 min to allow fusion Controlled cooling over 10–12 h to room temperature inside a closed furnace Controlled cooling over 10–12 h to room temperature inside a closed furnace Schematic of the materials and equipment used for fabricating synthetic thin sections via thermal heating and sintering of glass beads. 1) Refractory plate, 2) Spreading pottery clay over the polished refractory plate, 3) Smoothing the pottery clay, 4) Press molding on the refractory plate, 5) Sprinkling glass beads into the molds, 6) Demolding the samples, and 7) Synthetic thin section sample. Following sintering and cooling, the synthetic sections were demolded without damage, thanks to the non-adhesive properties of clay. Final edge trimming was performed using fine sandpaper to ensure consistent sample geometry, while avoiding cracking due to mechanical stress. The full fabrication process is summarized in Fig. 2, which illustrates the key steps including mold preparation, bead packing, thermal treatment, and post-processing. This method provides a robust, reproducible platform for evaluating wettability and contact angle behavior on controlled rough surfaces—critical for realistic modeling of subsurface fluid interactions.Fig. 2Step-by-step process for fabricating synthetic thin sections via thermal heating and sintering. Step-by-step process for fabricating synthetic thin sections via thermal heating and sintering. To systematically assess the effect of particle size on the morphology and uniformity of synthetic thin sections, perfectly spherical glass beads with mesh sizes ranging from 25 to 120 were used. These monodisperse beads, sintered at approximately 695 °C as described previously, ensured consistent surface roughness and structural integrity across all samples. As shown in Fig. 3, larger mesh sizes (e.g., 25, 35) produced thin sections with wider interstitial voids, whereas finer meshes (e.g., 100, 120) led to denser and more compact structures. Despite differences in packing density, the spherical geometry of the beads resulted in predictable and homogeneous surface textures. This uniformity is essential for reliable wettability and contact angle experiments, as it minimizes variability from local roughness fluctuations. The results confirm that the thermal sintering method, when applied to size-controlled spherical beads, yields mechanically robust and morphologically stable thin sections ideal for controlled interfacial studies.Fig. 3Representative synthetic thin sections produced via thermal heating and sintering using spherical glass beads with varying mesh sizes (25–120), 1.5 cm in diameter. Representative synthetic thin sections produced via thermal heating and sintering using spherical glass beads with varying mesh sizes (25–120), 1.5 cm in diameter. To evaluate the influence of slight grain shape deviations, additional synthetic thin sections were fabricated using near-spherical glass beads with mesh sizes of 17, 20, 30, and 40. As illustrated in Fig. 4, these samples display surface morphologies and packing patterns qualitatively comparable to those formed from fully spherical beads, albeit with minor variations in inter-particle contacts and local surface textures. Despite these small discrepancies, the results reaffirm the importance of using perfectly spherical beads in subsequent experiments to maintain strict control over surface characteristics. Such controlled morphology is critical for ensuring experimental reproducibility and for enabling reliable modeling of surface-driven phenomena, including fluid–solid interactions and wettability behavior in porous media.Fig. 4Synthetic thin sections fabricated using non-spherical glass beads with mesh sizes of 17, 20, 30, and 40 through thermal heating and sintering, 1.5 cm in diameter. Synthetic thin sections fabricated using non-spherical glass beads with mesh sizes of 17, 20, 30, and 40 through thermal heating and sintering, 1.5 cm in diameter. Synthesized thin sections used in this study serve as controlled physical analogs of reservoir rocks: they reproduce key geometric features of granular porous media while eliminating the mineralogical and chemical complexities inherent to natural samples. Similar to real rocks, the artificial thin sections are constructed from grains with defined size distributions whose packing and thermally induced bonding create interconnected pore structures and intrinsic surface roughness. However, unlike natural sections—where geological processes introduce uncontrolled heterogeneity in mineral composition, surface chemistry, and pore morphology—the synthesized samples provide a simplified and highly reproducible platform. This controlled design is particularly advantageous for wettability studies, as it allows isolation of specific parameters and reduces the influence of confounding geological factors. Thus, while the artificial thin sections do not replicate the full complexity of reservoir rocks, they offer a practical and scientifically rigorous means to investigate pore-scale mechanisms with enhanced clarity and repeatability. Procedure Contact angle measurement is a widely accepted technique for characterizing surface wettability in rock samples. The standard procedure involves sequential steps30: thin section preparation, surface polishing, solvent cleaning (e.g., acetone or toluene), and controlled drying. Once prepared, a liquid droplet is placed on the surface, and high-resolution images are captured to quantify the contact angle at the solid–liquid–air interface. Image analysis software (e.g., ImageJ) is employed to compute the contact angle, which serves as an indicator of wettability: angles < 90° denote hydrophilic surfaces, while those > 90° reflect hydrophobicity. To ensure precision, measurements are repeated across multiple regions of the surface and the average value is reported. This method provides reproducible and quantitative evaluation of fluid–solid interactions on natural rock surfaces. A key limitation of conventional contact angle measurements on cut thin sections stems from the polishing process, which removes the native micro-scale roughness and distorts the true surface geometry of reservoir rocks. This alteration compromises the representativeness of wettability assessments. To address this issue, synthetic thin sections were developed using both spherical and non-spherical glass beads. This approach preserves the physical and geometrical characteristics of real reservoir grains, maintaining surface morphology and enabling more accurate, realistic evaluation of contact angle and wettability under conditions that closely mimic those in porous reservoir systems. Factors influencing the non-penetration of liquid droplets into cut rock thin sections during contact angle measurements In conventional polished thin sections, droplets of water or paraffin typically remain on the surface in a lens-like or spherical cap form without penetrating the underlying porous structure. This behavior results from multiple physical and chemical factors intrinsic to the rock–fluid system. Firstly, the surface wettability of the rock plays a decisive role—hydrophobic surfaces maintain high contact angles and prevent infiltration, while hydrophilic ones promote spreading and absorption31. Secondly, the pore size and structure of the rock influence capillary entry; extremely small pores or pores coated with hydrocarbons often resist penetration32. The surface tension of the liquid is another governing factor—high surface tension favors droplet cohesion and inhibits entry unless capillary forces are sufficient to overcome this resistance33. Additionally, capillary dynamics, which are affected by pore geometry and contact angle, may prevent infiltration if the balance of forces is not favorable34. The chemical composition and surface coatings of the rock, such as hydrophobic minerals or organic films, can further reduce wettability and block entry35. Experimental conditions, including temperature, humidity, and the presence of trapped gases, also affect infiltration; dry or gas-filled pores can oppose liquid absorption36. Moreover, both droplet volume and deposition rate play a role—a small or slowly applied droplet may lack the energy or residence time needed to penetrate the medium37. Lastly, thin section thickness is crucial: extremely thin samples may not preserve full 3D pore connectivity, limiting fluid entry or mimicking two-dimensional behavior38. In contrast, synthetic thin sections—designed to preserve natural surface morphology—often allow droplet infiltration, introducing a challenge for accurate contact angle measurement despite their improved morphological realism. Limitations in contact angle measurement on synthetic thin sections due to complete droplet infiltration The results demonstrate that, due to the intrinsic tendency of the liquid to act as the wetting phase in the presence of gas, coupled with factors such as relatively large pore sizes, dominant capillary forces, and the increased thickness of synthetic thin sections, paraffin droplets readily infiltrate the porous structure of the samples. Although these sections accurately replicate natural surface morphology and grain geometry, such infiltration hinders practical contact angle measurement and surface wettability evaluation. For comparison, a droplet of red-dyed paraffin placed on a non-porous glass cover slip yields a contact angle of 15°, confirming the strong oil-wet nature of the glass surface. In contrast, as shown in Fig. 5, paraffin droplets deposited on synthetic thin sections are rapidly absorbed into the pore network. The droplets never remain on the surface long enough to allow for contact angle imaging, even when applied successively. Instead, each droplet saturates the medium and displaces entrapped air, illustrating the limitations of using highly permeable synthetic media for conventional wettability assessments.Fig. 5Complete infiltration of paraffin droplets into the synthetic thin section. Complete infiltration of paraffin droplets into the synthetic thin section. To overcome the challenge of paraffin infiltration in synthetic thin sections, a three-phase system involving water, paraffin, and air can be employed to regulate wettability behavior. By pre-saturating the porous medium with water, paraffin infiltration can be effectively suppressed. This principle is demonstrated experimentally in Fig. 6 (first row), where a synthetic thin section previously saturated with paraffin is immersed in water. Due to the preferential wettability of glass surfaces toward water—driven by their surface energy characteristics—paraffin acts as the non-wetting phase. Upon immersion, the embedded paraffin droplets are displaced and expelled from the porous network, eventually floating to the water surface. This behavior confirms that, within a water–paraffin–air system, water dominates as the wetting phase, enabling the manipulation of interfacial interactions and fluid occupancy in porous structures through careful fluid selection and saturation protocols.Fig. 6Experimental demonstration of saturation stability and prevention of paraffin infiltration in a semi-immersed synthetic thin section. First row; paraffin droplet infiltration, soaking sample into the water to extract paraffin, and semi-immersed synthetic thin section. Second row show fully saturated sample with water, each sample is 1.5 cm in diameter. Experimental demonstration of saturation stability and prevention of paraffin infiltration in a semi-immersed synthetic thin section. First row; paraffin droplet infiltration, soaking sample into the water to extract paraffin, and semi-immersed synthetic thin section. Second row show fully saturated sample with water, each sample is 1.5 cm in diameter. A smart approach for contact angle measurement on highly rough and porous surfaces To enable reliable contact angle measurements on highly rough and porous surfaces—where liquid droplets typically infiltrate the pore network and fail to maintain stable profiles—a controlled three-phase technique is proposed. In this method, the synthetic thin section is pre-saturated with water, filling internal pores while preserving surface asperities. A paraffin droplet is then deposited on the air-exposed upper surface, where it remains stable due to immiscibility with water and the capillary barrier created by underlying saturation. As illustrated in Fig. 6 (first row), the thin section is maintained in a semi-immersed state throughout the experiment: the lower portion remains submerged to ensure saturation stability, while the top surface remains accessible for droplet deposition. This setup achieves a delicate balance among capillary forces, gravity, and atmospheric pressure—preventing water drainage and paraffin infiltration during the measurement. Importantly, this technique preserves the true surface roughness profile and prevents dynamic changes in wettability conditions, allowing for accurate and repeatable contact angle evaluation. Critical experimental parameters—including immersion depth, ambient temperature, and humidity—must be closely controlled, as fluctuations can lead to evaporation or saturation loss, compromising measurement accuracy. Overall, this innovative approach enables robust wettability characterization of porous surfaces while accounting for the effects of roughness and multiphase interactions under well-defined conditions. To validate the stability of water saturation within the pores of the synthetic thin section and confirm that the surface roughness profile remains constant during measurements, a simple yet effective experiment was performed. As shown in Fig. 6 (second row), a synthetic thin section partially immersed in blue-dyed water was subjected to capillary testing by gently applying a paper tissue to its exposed upper surface. The continuous absorption of blue-colored water by the tissue indicated an uninterrupted upward flow of water through the porous matrix, effectively replacing any extracted moisture. This self-regulating capillary behavior confirms that the height of water saturation remains stable throughout the experiment, thereby preserving the saturation state of subsurface pores. Consequently, paraffin droplets deposited on the upper surface do not infiltrate the underlying network, enabling accurate contact angle measurement on rough and porous media without interference from dynamic fluid redistribution. Figure 7 presents the procedure for contact angle measurement on rough and porous surfaces using a synthetic thin section in a semi-immersed configuration, fully saturated with blue-colored water. The sample is partially immersed to maintain internal pore saturation while preserving dry surface asperities. A paraffin droplet is precisely dispensed onto the air-exposed surface via a syringe needle with a controlled gauge. As the sequence shows, the droplet remains stable and does not infiltrate the porous network, enabling accurate angle observation. Gradual addition of paraffin increases the droplet volume and accentuates its curvature, allowing for a direct evaluation of how surface roughness and morphology influence wettability. This method effectively eliminates the confounding effects of pore infiltration, thereby enhancing the reliability of contact angle analysis on porous substrates.Fig. 7Sequential deposition of paraffin droplets on the air-exposed surface of a water-saturated synthetic thin section, each sample is 1.5 cm in diameter. Sequential deposition of paraffin droplets on the air-exposed surface of a water-saturated synthetic thin section, each sample is 1.5 cm in diameter. As illustrated in Fig. 8a–d, maintaining synthetic thin sections in a semi-immersed state allows capillary forces to draw water upward through the porous network, saturating internal pore spaces while leaving the topmost surface layer air-filled. This configuration ensures that surface roughness remains fully exposed and unaltered. When a paraffin droplet is deposited onto the saturated surface (Fig. 8a), it becomes immobilized within the surface asperities, forming a stable and well-defined morphology suitable for accurate contact angle measurement. In contrast, without prior water saturation (Fig. 8b), the paraffin infiltrates the pore network, contacting both solid and trapped air, which distorts the droplet profile and prevents reliable wettability analysis. Figure 8c and d further reveal that a thin aqueous layer beneath the surface acts as a capillary barrier, isolating the droplet from the porous interior and allowing it to rest on the air-filled surface features. This approach provides a controlled environment to assess wettability on rough surfaces by decoupling surface interaction from subsurface absorption, enhancing the realism and reproducibility of contact angle evaluations in porous media.Fig. 8Comparison of paraffin droplet behavior on water-saturated and unsaturated synthetic thin sections. (a) Stable positioning of a paraffin droplet on the air-exposed rough surface of a water-saturated thin section using the semi-immersion method. (b) Infiltration of the paraffin droplet into the porous structure of an unsaturated thin section due to capillary suction. (c, d) Close-up images showing that the paraffin droplet rests on the surface asperities of the saturated thin section, with an underlying water layer preventing pore penetration and preserving surface roughness. Comparison of paraffin droplet behavior on water-saturated and unsaturated synthetic thin sections. (a) Stable positioning of a paraffin droplet on the air-exposed rough surface of a water-saturated thin section using the semi-immersion method. (b) Infiltration of the paraffin droplet into the porous structure of an unsaturated thin section due to capillary suction. (c, d) Close-up images showing that the paraffin droplet rests on the surface asperities of the saturated thin section, with an underlying water layer preventing pore penetration and preserving surface roughness. Figure 9 illustrates a custom-designed experimental setup developed to accurately measure contact angles and assess wettability on rough and porous surfaces. The core of this setup is a synthetic thin section composed of spherical glass beads, partially immersed in water to achieve full pore saturation while preserving a dry, air-exposed top surface. Paraffin droplets are gently deposited using a micropipette or fine-gauge syringe needle. A high-resolution side-view image is captured by a camera mounted perpendicular to the surface plane on a tripod to eliminate parallax errors. To enhance image clarity and droplet profile visibility, a constant backlight source is positioned behind the sample, ensuring uniform illumination. Captured images are analyzed with image processing software to extract the droplet geometry and compute the contact angle. This setup ensures stable, repeatable, and accurate contact angle measurements on textured surfaces by preventing droplet infiltration and isolating surface effects from subsurface influences, thereby enabling a realistic evaluation of wettability relative to surface roughness and microstructure.Fig. 9Schematic diagram of the experimental setup for contact angle measurement on rough porous surfaces. The setup includes light source, digital camera, tripod, micropipette, computer, and a partially water-immersed synthetic thin section. Schematic diagram of the experimental setup for contact angle measurement on rough porous surfaces. The setup includes light source, digital camera, tripod, micropipette, computer, and a partially water-immersed synthetic thin section. Results Evaluation of surface morphology of sintered synthetic thin sections constructed from irregular and spherical glass beads of various mesh sizes Figure 10 displays microscopic images of sintered synthetic thin sections fabricated from irregular-shaped glass beads with mesh sizes of 17, 20, 30, and 40. As mesh size increases—indicating smaller average particle diameters—the packing structure becomes denser and more uniform. Samples composed of larger beads (mesh 17 and 20) exhibit pronounced interstitial voids and irregularities due to non-spherical geometries, resulting in heterogeneous surface morphologies. This heterogeneity can significantly influence wettability and capillary dynamics during contact angle measurements. In contrast, samples with finer beads (mesh 30 and 40) demonstrate enhanced packing efficiency and reduced pore space, potentially leading to more stable and reproducible wetting behavior. These findings underscore the critical role of particle size and geometry in defining surface texture and intergranular porosity, both of which are essential for accurately modeling fluid–solid interactions in synthetic porous media.Fig. 10Microscopic images of sintered synthetic thin sections composed of irregular-shaped glass beads with mesh sizes of 17, 20, 30, and 40. The variation in particle size and shape results in different packing densities and surface morphologies across the samples. Microscopic images of sintered synthetic thin sections composed of irregular-shaped glass beads with mesh sizes of 17, 20, 30, and 40. The variation in particle size and shape results in different packing densities and surface morphologies across the samples. Figure 11 presents microscopic images of synthetic thin sections constructed from spherical glass beads across mesh sizes 25–120, fabricated via controlled thermal sintering. This method allows interparticle bonding without compromising the spherical geometry, yielding solid yet porous structures with preserved surface topography. At lower mesh sizes (25–50), the resulting textures are coarser, featuring fewer beads, wider pore spaces, and limited contact points, which may facilitate deeper fluid infiltration and elevated permeability. Conversely, higher mesh sizes (80–120) yield finer textures with denser packing, reduced void space, and more interconnected microstructures. These finer surfaces promote stable droplet retention and enhanced capillary pinning, potentially resulting in higher apparent contact angles39. The systematic variation in bead size offers valuable insights into how particle-scale roughness governs wettability, capillary behavior, and fluid–solid interactions. This progression from coarse to fine textures enables tailored modeling of natural porous media or engineered surfaces for advanced wetting studies.Fig. 11Microscopic images of sintered synthetic thin sections composed of spherical glass beads with mesh sizes ranging from 25 to 120. The images illustrate how bead size affects the surface texture and pore structure of the sections. Microscopic images of sintered synthetic thin sections composed of spherical glass beads with mesh sizes ranging from 25 to 120. The images illustrate how bead size affects the surface texture and pore structure of the sections. Arrangement and packing of constituents in synthetic thin sections Figures 12 and 13 illustrate the geometric packing of synthetic porous media constructed from spherical and non-spherical glass beads. The organization and packing of grains during hydrocarbon reservoir rock formation critically influence porosity and permeability. In this study, monodisperse spherical glass beads were used to replicate ordered granular assemblies, predominantly forming Hexagonal Close Packing (HCP) and Cubic Close Packing (CCP) structures—both exhibiting a theoretical packing density of ~ 74% (porosity ~ 26%)40. The fabrication process involved three key steps: (1) selection of dimensionally uniform beads, (2) controlled sedimentation for uniform arrangement, and (3) sintering near the glass softening point to preserve packing architecture. While HCP follows an ABAB… stacking and CCP an ABCABC… sequence, both yield isotropic and repeatable porous networks. Notably, irregular (non-spherical) glass beads were also capable of forming quasi-ordered packings, with Fig. 13c confirming high-density arrangements like spherical systems. These findings demonstrate that both particle shape and packing strategy play crucial roles in tailoring the porosity and structure of artificial porous media for fluid flow and wettability studies.Fig. 12Non-spherical glass beads exhibiting geometries resembling quasi-spherical and ellipsoidal shapes.Fig. 13Packing arrangement of spherical and non-spherical glass beads. (a) Cubic close packing (CCP) arrangement of spherical glass beads, (b) Hexagonal close packing (HCP) arrangement of spherical glass beads, (c) Combined CCP and HCP arrangements observed in non-spherical glass beads. Non-spherical glass beads exhibiting geometries resembling quasi-spherical and ellipsoidal shapes. Packing arrangement of spherical and non-spherical glass beads. (a) Cubic close packing (CCP) arrangement of spherical glass beads, (b) Hexagonal close packing (HCP) arrangement of spherical glass beads, (c) Combined CCP and HCP arrangements observed in non-spherical glass beads. Regularly packed synthetic thin sections composed of spherical glass beads (e.g., FCC and HCP structures) enable precise prediction of key physical and hydraulic properties41. Once the particle size (R) and packing type are defined, geometrical relationships allow for the direct estimation of pore radius (rₚ) and throat radius (rₜ) (Eqs. 1 and 2)42, while porosity—analytically fixed at ~ 26% for dense packings—facilitates permeability prediction via the Carman–Kozeny model (Eq. 3)43. Capillary pressure (Pc) is estimated using the Young–Laplace equation (Eq. 4)44, incorporating interfacial tension and contact angle. These models effectively link microstructure to macroscopic flow behavior, enabling accurate evaluation of droplet infiltration, wettability, and multiphase transport in artificial porous media. Although FCC and HCP packings differ in their stacking sequences, they share nearly identical porosity, inter-particle geometries, and flow characteristics. Therefore, both systems yield comparable predictions for permeability and capillary behavior. For modeling, empirical constants such as C = 180 and tortuosity τ = 1.5 are adopted in the Carman–Kozeny equation, while the surface tension and contact angle for water–glass systems are taken as 72 mN/m and 10°, respectively. In addition to the permeability values estimated using the Carman–Kozeny relationship, permeability was also experimentally measured using a gas permeameter with nitrogen. The measured values were in the same order of magnitude and showed good agreement with the calculated permeabilities. Experimental porosity values, measured via the gravimetric method, ranged from 23 to 30%, closely aligning with theoretical predictions and validating the structural integrity of the sintered thin sections. This variation stems from sintering temperature, bead size distribution, and mold constraints. Notably, quasi-spherical (ellipsoidal) beads also formed dense, regular arrangements, confirming that structural parameters derived from spherical systems can be extended to similar non-spherical geometries. These estimations—summarized in Table 1—provide a unified basis for characterizing fluid behavior across diverse synthetic porous systems.Table 1Estimation of Physical and Dynamic Properties in Densely Packed Ordered Arrangements of Spherical Beads.Glass beads radius (R) Micrometer (mesh)Porosity φ PercentPore radius (Rp) MicrometerThroat radius \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${(\mathrm{r}}_{\mathrm{t}})$$\end{document} MicrometerPermeability (k) DarcyWater–air capillary pressure (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{P}}_{\mathrm{c}}$$\end{document}) KP354 (25)2614553102.7250 (35)261033853.7200 (40)2682303.24.7149 (50)2661221.786.5125 (60)2651191.257.5105 (70)2643160.888.989 (80)2636130.6310.975 (100)2631110.4512.963 (120)262690.3215.81\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{r}}_{\mathrm{p}}=0.41 \mathrm{R}$$\end{document}2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{r}}_{\mathrm{t}}=0.15 \mathrm{R}$$\end{document}3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{k}=\frac{{\upvarphi }^{3}{\mathrm{R}}^{2}}{\mathrm{C}{{\uptau }^{2}(1-\upvarphi )}^{2}}$$\end{document}4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{P}}_{\mathrm{c}}=\frac{2\upsigma \mathrm{c}\mathrm{o}\mathrm{s}\uptheta }{{\mathrm{r}}_{\mathrm{t}}}$$\end{document} Table 1Estimation of Physical and Dynamic Properties in Densely Packed Ordered Arrangements of Spherical Beads.Glass beads radius (R) Micrometer (mesh)Porosity φ PercentPore radius (Rp) MicrometerThroat radius \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${(\mathrm{r}}_{\mathrm{t}})$$\end{document} MicrometerPermeability (k) DarcyWater–air capillary pressure (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{P}}_{\mathrm{c}}$$\end{document}) KP354 (25)2614553102.7250 (35)261033853.7200 (40)2682303.24.7149 (50)2661221.786.5125 (60)2651191.257.5105 (70)2643160.888.989 (80)2636130.6310.975 (100)2631110.4512.963 (120)262690.3215.8 Estimation of Physical and Dynamic Properties in Densely Packed Ordered Arrangements of Spherical Beads. Table 1 presents the estimated physical and flow-related properties of synthetic thin sections constructed from spherical glass beads with varying radii. A consistent trend is observed: as bead size increases, both pore radius (rₚ) and throat radius (rₜ) increase proportionally. This trend is expected from the geometric structure of dense packings like FCC or HCP, where void spaces grow proportionally with particle size. Despite this variation, porosity remains approximately constant (φ ≈ 0.26), reflecting the theoretical packing density of ordered structures. Dynamic properties, however, exhibit size-dependent behavior. Permeability (k) increases with bead size, in agreement with the Carman–Kozeny model (k ∝ R2), highlighting reduced flow resistance in structures with larger pore pathways. In contrast, capillary pressure (Pc) decreases with increasing bead size, as predicted by the Young–Laplace equation (Pc ∝ 1/rₜ), indicating that larger throats require lower pressure for fluid invasion. This dual effect—enhanced flow and reduced capillary resistance—demonstrates that bead size acts as a key control parameter in designing porous systems with tailored flow characteristics. Overall, these findings validate the use of geometrically controlled synthetic thin sections as reliable analogs for natural porous media. Comparison of droplet shape on smooth and rough surfaces When deposited on a smooth and homogeneous surface, a water droplet typically adopts a symmetric, lens-like shape governed primarily by surface tension and substrate uniformity. In such ideal conditions, the contact angle remains uniform in all directions and reflects the intrinsic wettability of the surface (Fig. 14). However, on rough or heterogeneous surfaces—such as natural stone—surface asperities and depressions introduce localized variations in adhesive forces, disrupting the droplet’s geometry. As illustrated in Fig. 15, this can lead to asymmetric shapes, distortion of the contact line, or even fragmentation into smaller droplets. Known as the surface roughness effect, this phenomenon alters the apparent contact angle, often deviating significantly from the theoretical value due to topographical pinning, capillary effects, and selective adhesion to microstructural features. Overall, droplet behavior on rough surfaces is shaped by the balance between cohesive liquid forces and adhesive interactions with the substrate, modulated by surface texture. This interplay affects not only contact angle and morphology but also wetting dynamics and stability, underscoring the critical role of surface topography in wettability assessments45.Fig. 14Spherical geometry of a droplet on a smooth and polished surface; Irregular geometry of a droplet on a rough and uneven surface.Fig. 15Completely irregular shape of a droplet on the artificial thin-section surface, each sample is 1.5 cm in diameter. Spherical geometry of a droplet on a smooth and polished surface; Irregular geometry of a droplet on a rough and uneven surface. Completely irregular shape of a droplet on the artificial thin-section surface, each sample is 1.5 cm in diameter. Surface roughness confirmation following water saturation via semi-immersion method To ensure that surface roughness features remain unaltered during semi-immersion saturation, microscopic imaging was conducted on the synthetic thin sections under experimental conditions. As illustrated in Fig. 16 (c and d), the surface micro-relief, including peaks and valleys, remains clearly visible, confirming that water saturation does not obscure the topographical features. A side-view image (Fig. 16a) provides additional evidence of the three-dimensional roughness, while Fig. 16b—captured under high magnification after paraffin saturation—demonstrates the spatial arrangement of spherical glass beads and the fluid distribution at the pore scale. These visual observations verify that the semi-immersion method preserves surface texture, enabling accurate analysis of roughness-induced effects on wettability and contact angle behavior in synthetic porous media.Fig. 16Visual confirmation of preserved surface roughness after water saturation via the semi-immersion method. (a, b and c) Side views of synthetic thin sections showing the maintained micro-roughness and protrusions after partial immersion in blue-dyed water. (d) Microscopic image illustrating the packing arrangement of spherical glass beads in the surface layer when fully saturated with paraffin. Visual confirmation of preserved surface roughness after water saturation via the semi-immersion method. (a, b and c) Side views of synthetic thin sections showing the maintained micro-roughness and protrusions after partial immersion in blue-dyed water. (d) Microscopic image illustrating the packing arrangement of spherical glass beads in the surface layer when fully saturated with paraffin. Surface roughness characterization of artificial thin sections via profilometry Surface roughness was quantitatively evaluated using a non-contact laser profilometer, a precise and widely used method in surface engineering. This technique enables high-resolution mapping of topographic features without damaging the sample46. Key parameters such as average roughness (Ra) and roughness coefficient (r) were measured under semi-immersion saturation conditions to preserve surface morphology. The measured roughness plays a critical role in wettability behavior, influencing contact angle through models like Wenzel and Cassie–Baxter. The profilometer used in this study provided a vertical resolution of 5 μm, allowing for accurate detection of surface irregularities essential for interpreting fluid–solid interactions. Surface roughness characterization was performed using a profilometer, which scanned the synthetic thin sections along predefined lines to capture height variations (Z) relative to horizontal and vertical distances (XY). The resulting 2D roughness profiles (Fig. 17) illustrate the surface height deviations from the mean line. Samples with lower mesh sizes (e.g., 25 and 35) displayed pronounced peaks and deep valleys, reflecting their coarser granular structure. In contrast, higher mesh samples (e.g., 100 and 120) exhibited finer, high-frequency oscillations with smaller amplitude, indicative of smoother but more complex micro-topography. In addition to line profiles, 3D surface maps (Fig. 18) were generated, offering a comprehensive visualization of surface topography across both lateral dimensions. These 3D reconstructions provide valuable insights into the spatial distribution of roughness, enabling the identification of localized features such as anisotropy, repetitive patterns, micro-defects, and potential wear zones. This combination of 2D and 3D analyses allows for a detailed evaluation of surface morphology and its role in wettability and fluid–solid interactions.Fig. 172D surface roughness profiles of synthetic thin sections prepared with spherical glass beads of various mesh sizes (23, 35, 40, 50, 60, 70, 80, 100, and 120), showing pronounced amplitude variations for coarse meshes (e.g., 23, 35) and finer, more frequent undulations for fine meshes (e.g., 100, 120).Fig. 183D surface topography maps of synthetic thin sections prepared with spherical glass beads of different mesh sizes (25, 35, 40, 50, 60, 70, 80, 100, and 120), illustrating larger peaks and valleys for coarse meshes and more uniform micro-scale textures for fine meshes. 2D surface roughness profiles of synthetic thin sections prepared with spherical glass beads of various mesh sizes (23, 35, 40, 50, 60, 70, 80, 100, and 120), showing pronounced amplitude variations for coarse meshes (e.g., 23, 35) and finer, more frequent undulations for fine meshes (e.g., 100, 120). 3D surface topography maps of synthetic thin sections prepared with spherical glass beads of different mesh sizes (25, 35, 40, 50, 60, 70, 80, 100, and 120), illustrating larger peaks and valleys for coarse meshes and more uniform micro-scale textures for fine meshes. Artificial thin sections were fabricated using fully spherical glass beads across nine mesh sizes (25 to 120), thermally sintered to achieve mechanically stable and reproducible packing structures. The influence of bead size on surface morphology was evaluated using a non-contact laser profilometer, generating both 2D roughness profiles (Fig. 17) and 3D topographic maps (Fig. 18) for each sample. Larger mesh sizes (25 and 35) produced high-amplitude, low-frequency undulations, with sharp transitions in the 2D profiles and prominent peak-valley patterns in the 3D maps—indicative of coarse surface roughness and well-defined bead curvature. Intermediate mesh sizes (40 to 80) showed moderate roughness, characterized by more compact packing, reduced amplitude, and increased density of surface asperities. The 2D profiles demonstrated smoother transitions, while the 3D surfaces appeared more homogeneous, though still textured. Fine mesh samples (100 and 120) exhibited low-amplitude, high-frequency fluctuations with quasi-flat macro-scale morphology and retained micro-scale roughness essential for wettability analysis. These observations reflect the systematic correlation between bead size and surface texture, emphasizing the effectiveness of the fabrication method in producing well-controlled and structurally consistent synthetic thin sections. Profilometric analysis revealed a distinct morphological transition with decreasing bead mesh size. Coarse-mesh surfaces (larger beads) exhibited high-amplitude, low-frequency roughness with pronounced periodicity, reflecting deep pore throats and bead curvature. In contrast, fine-mesh surfaces (smaller beads) displayed low-amplitude, high-frequency textures, characterized by a more isotropic micro-asperity distribution. These morphological differences are expected to impact wettability behavior: coarse surfaces favor Wenzel-type wetting due to deeper infiltration, while fine textures may support Cassie–Baxter regimes through air entrapment beneath the droplet. The parameters r and Rₐ both describe surface roughness but differ in meaning and scale. The roughness ratio (r) reflects the ratio of actual to apparent surface area, capturing large-scale topographic features and is central to the Wenzel model, where increased r enhances droplet contact. In contrast, average roughness (Rₐ) measures fine-scale height deviations from the mean line using profilometers, indicating micro/nanoscopic texture. While r defines the theoretical surface area, Rₐ determines practical wetting behavior, influencing whether a droplet penetrates or rests on the roughness. Table 2 summarizes the surface roughness parameters derived from profilometer measurements, including the average roughness (Rₐ), roughness ratio (r), and theoretical roughness depth (h) for synthetic thin sections composed of spherical glass beads of various mesh sizes. As demonstrated in Fig. 19, a clear trend emerges: decreasing mesh number (i.e., increasing bead size) leads to higher surface roughness. This is evident from the enhanced amplitude of 2D roughness profiles and the increased density and intensity of peaks in the 3D topography maps. Larger beads generate deeper and more defined surface cavities, resulting in higher values of Rₐ and r. However, a notable deviation is observed between Rₐ and h for fine-mesh samples, particularly in Fig. 20, where experimental Rₐ values fall below the corresponding theoretical depths. This discrepancy is attributed to capillary rise, which causes partial water filling above the throat level, thereby reducing the actual vertical height variation captured during profilometer scanning under wet conditions. While h represents the idealized geometric cavity depth, Rₐ reflects the effective roughness in the wetted state, offering a more realistic measure for analyzing droplet-surface interactions on porous media.Table 2Quantitative surface roughness characteristics obtained from profilometer test results.Glass beads radius (R) Micrometer (mesh)Roughness depth (theory) (h) MicrometerRoughness depth (experiment) (Ra) MicrometerSurface roughness coefficient (r) DimensionlessFlat surfaceZeroZero1354 (25)40739510.38250 (35)2882719.02200 (40)2302148.02149 (50)1711556.69125 (60)1441225.47105 (70)121954.9289 (80)102754.1475 (100)86563.3463 (120)72402.66Fig. 19Surface roughness coefficient (r) as a function of glass bead size.Fig. 20Comparative graph of theoretical and experimental roughness depth as a function of glass bead size. Table 2Quantitative surface roughness characteristics obtained from profilometer test results.Glass beads radius (R) Micrometer (mesh)Roughness depth (theory) (h) MicrometerRoughness depth (experiment) (Ra) MicrometerSurface roughness coefficient (r) DimensionlessFlat surfaceZeroZero1354 (25)40739510.38250 (35)2882719.02200 (40)2302148.02149 (50)1711556.69125 (60)1441225.47105 (70)121954.9289 (80)102754.1475 (100)86563.3463 (120)72402.66 Quantitative surface roughness characteristics obtained from profilometer test results. Surface roughness coefficient (r) as a function of glass bead size. Comparative graph of theoretical and experimental roughness depth as a function of glass bead size. Discussion To investigate the performance of the artificial thin section during partial immersion in water, as well as the placement of a paraffin droplet on the surface roughness of the artificial thin section, it is necessary to separately examine the mechanisms and effective forces involved in each stage. These stages include: (i) the saturation of the artificial thin section with water, (ii) the penetration of the paraffin droplet into the surface asperities and pore spaces of the thin section, and (iii) the spreading of the paraffin droplet over the surface of the artificial thin section. The following discussion addresses the underlying mechanisms and the dominant forces governing each of these processes. This analysis is crucial for understanding the interplay between capillary forces, surface tension, wettability, and gravitational effects in controlling both the penetration behavior within the porous microstructure and the macroscopic spreading pattern of the droplet. The results also provide valuable insights for predicting and optimizing fluid–solid interactions in artificial porous media with controlled surface roughness and pore geometry. Mechanism of saturation of artificial thin sections by partial immersion in water In the partial immersion experiments of artificial thin sections in water, two primary forces govern the saturation behavior of the porous structure: capillary force and gravitational force. Capillary force, driven by the adhesion of water molecules to the pore walls and the surface tension at the water–air interface, tends to pull water upward into the pore network. In contrast, gravity acts to pull the water downward (Fig. 21). Due to the microscopic scale of the pores and throats in the artificial thin sections, capillary forces significantly dominate over gravitational forces, allowing water to rise and remain stable within the pore space—even when the sample is only partially immersed. This capillary retention ensures that the internal structure remains saturated, while the upper surface appears dry and suitable for further testing. The hydrostatic pressure caused by gravity (Eq. 5) —calculated based on the constant section thickness (5 cm), water density (1000 kg/m3), and gravitational acceleration (9.81 m/s2)—was found to be 0.491 kPa for all samples. Meanwhile, capillary pressure, calculated using the Young–Laplace equation (Eq. 4), was determined for each thin section based on its throat radius (Table 3). In all cases, capillary pressure exceeds gravitational pressure, and this difference becomes more pronounced as the throat radius decreases. This means finer pore structures exhibit even stronger water retention due to enhanced capillary action. To further analyze the dominance of these forces, the dimensionless Bond number (Bo)—defined as the ratio of gravitational to capillary forces (Eq. 6)—was calculated. For all throat sizes in the artificial thin sections, the Bond numbers were much smaller than 1, confirming that capillary forces overwhelmingly govern the system. This behavior is consistent with natural systems, such as water transport in plants or absorption in sponges, where capillarity enables fluid movement and retention against gravity. In conclusion, artificial thin sections under partial immersion remain stably saturated due to dominant capillary forces, while their top surfaces remain dry and accessible. This stable saturation condition is essential for accurate contact angle measurement and wettability evaluation, as it prevents uncontrolled droplet infiltration and ensures the surface roughness and morphology remain unaffected for reliable analysis.Fig. 21Balance of forces during partial immersion of an artificial thin section in water.Table 3Estimation of the Bond number and equilibrium height in the water imbibition process within the porous medium of the synthetic thin section.Glass beads radius (R) Micrometer (mesh)Bond number (Bo) DimensionlessEquilibrium height (hmax) cm354 (25)0.0003928250 (35)0.000238200 (40)0.0001248149 (50)0.00006766125 (60)0.0000576105 (70)0.0000359189 (80)0.00002311175 (100)0.00001713163 (120)0.000011161 Balance of forces during partial immersion of an artificial thin section in water. Table 3Estimation of the Bond number and equilibrium height in the water imbibition process within the porous medium of the synthetic thin section.Glass beads radius (R) Micrometer (mesh)Bond number (Bo) DimensionlessEquilibrium height (hmax) cm354 (25)0.0003928250 (35)0.000238200 (40)0.0001248149 (50)0.00006766125 (60)0.0000576105 (70)0.0000359189 (80)0.00002311175 (100)0.00001713163 (120)0.000011161 Estimation of the Bond number and equilibrium height in the water imbibition process within the porous medium of the synthetic thin section. When artificial thin sections are partially immersed in water, capillary imbibition draws the fluid upward into the porous network until equilibrium is reached between capillary pressure and hydrostatic pressure (Eq. 7). As demonstrated in Table 3, the calculated equilibrium height (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{h}}_{\mathrm{m}\mathrm{a}\mathrm{x}}$$\end{document}) far exceeds the physical thickness of the thin Sects. (5 cm), confirming that the porous structure remains fully saturated under capillary action. Despite this, no water leakage is observed due to the stabilizing effect of the meniscus at the solid–liquid–air interface. This curvature arises from the balance between surface tension, adhesion, and cohesion, and depends on the contact angle between the liquid and the solid. For water on glass, where the contact angle is < 90°, a concave meniscus forms, generating negative pressure (Eq. 8) that prevents drainage. This pressure stabilizes the liquid column inside the pores. Since the meniscus forms at the narrowest parts of the pore network, its radius (Rₘ) is approximately equal to the throat radius (rₜ). Thus, pore geometry directly controls saturation stability47.5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{P}}_{\mathrm{g}}=\frac{{\mathrm{F}}_{\mathrm{g}}}{\mathrm{A}}=\uprho \mathrm{g}\mathrm{h}$$\end{document}6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{B}}_{\mathrm{o}}=\frac{\uprho {\mathrm{gr}}_{\mathrm{t}}^{2}}{\upsigma \mathrm{c}\mathrm{o}\mathrm{s}\uptheta }$$\end{document}7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{P}}_{\mathrm{c}}={\mathrm{P}}_{\mathrm{g}} \to {\mathrm{h}}_{\mathrm{m}\mathrm{a}\mathrm{x}}=\frac{2\upsigma \mathrm{c}\mathrm{o}\mathrm{s}\uptheta }{\uprho {\mathrm{gr}}_{\mathrm{t}}}$$\end{document}8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta \mathrm{P}=\upsigma \left(\frac{1}{{\mathrm{R}}_{1}}+\frac{1}{{\mathrm{R}}_{2}}\right)=\frac{2\upsigma }{{\mathrm{R}}_{\mathrm{m}}}$$\end{document} In synthetic porous media composed of uniformly packed spherical glass beads, surface roughness arises from two distinct but interacting scales. The primary contributor to macroscopic roughness is the geometric protrusion of the spherical particles themselves, which defines the coarse topography of the thin section surface and corresponds directly to the bead radius. At a finer scale, the meniscus phenomenon—manifesting as a concave curvature at the liquid–air interface within pore throats—introduces additional roughness associated with the radius of the meniscus, which approximates the throat radius. Despite its smaller scale, this localized curvature occurs uniformly across the surface due to the regularity and symmetry of the bead packing, forming a continuous network of menisci. As such, the overall surface roughness of the system can be interpreted as a composite parameter, integrating both the macroscopic roughness from particle geometry and the microscopic roughness induced by capillary menisci. This dual-scale perspective is illustrated in Fig. 22, where the total roughness is conceptualized as the sum of the bead-induced and meniscus-induced roughness components. The analysis emphasizes that, in highly ordered porous systems, even microscale phenomena like meniscus formation can play a significant role in defining surface properties, especially in applications involving wettability, capillarity, and fluid–solid interactions.Fig. 22Presence of two void spaces contributing to surface roughness for paraffin droplet penetration: the upper void, with a larger volume, corresponds to the pore cavity, while the lower void corresponds to the pore throat or concave meniscus volume. Presence of two void spaces contributing to surface roughness for paraffin droplet penetration: the upper void, with a larger volume, corresponds to the pore cavity, while the lower void corresponds to the pore throat or concave meniscus volume. In the capillary-driven water imbibition process within synthetic thin sections, the surface tension and wettability remain constant across all bead sizes, as they are defined by the same water–air interface and identical glass surface chemistry. Consequently, the meniscus radius—governed by these two parameters—remains constant for all samples. The only variable influencing capillary behavior among different bead size classes is the pore throat radius, which directly affects the resulting capillary pressure and, therefore, the equilibrium water rise height within the porous medium. Meniscus formation is typically assumed to occur within the pore throats; however, in porous media composed of very fine spherical beads, the extremely small throat dimensions, combined with mold constraints during thin section fabrication, may allow the meniscus to partially extend above the pore throat level (Fig. 23b). This partial extension can lead to reduced apparent surface roughness, as portions of the topographical features may be masked by water. Nonetheless, even in such cases, the fine-bead samples continue to exhibit significantly lower surface roughness compared to coarse-bead samples (Fig. 23a), thereby preserving the overall trend. This observation confirms that the reduction in measured roughness for fine-bead thin sections is intrinsic to their geometry and does not undermine the validity of conclusions regarding the effect of roughness on contact angle measurements and wettability assessment.Fig. 23Water rise to the upper surface of synthetic thin sections: (a) water rise confined within the pore throats of coarse beads, and (b) water rise extending above the pore throats in fine beads. Water rise to the upper surface of synthetic thin sections: (a) water rise confined within the pore throats of coarse beads, and (b) water rise extending above the pore throats in fine beads. Mechanism of paraffin droplet penetration into the surface roughness of the synthetic thin section Following the analysis of the forces responsible for water rise within the synthetic thin section, attention shifts to the interaction between a paraffin droplet and the rough, porous surface of the sample during contact angle measurement. As illustrated in Fig. 22, two distinct types of surface voids contribute to the overall roughness and serve as potential sites for paraffin infiltration: (i) upper-level voids representing pore spaces, with dimensions governed by the pore radius, and (ii) deeper-level voids located within the meniscus curvature zone, defined by the throat radius. Upon placement of a paraffin droplet onto the semi-immersed synthetic thin section, capillary forces may drive the liquid into these surface depressions due to the roughness-induced pressure differentials (Fig. 24). In the air–paraffin system that exists on the outer surface, paraffin acts as the wetting phase relative to air and is thus energetically drawn into the roughness features. However, since water is already present deeper within the structure—specifically at the meniscus layer—distinct fluid–fluid interfaces are established at different roughness depths. For the pore-associated roughness, the relevant capillary pressure (Pc) is calculated using the paraffin–air contact angle (15°) and interfacial tension (25 mN/m), applying the pore radius in the Young–Laplace equation. In contrast, for the meniscus-associated roughness, the paraffin–water–solid interaction governs the capillary behavior. Here, the throat radius is the relevant geometric parameter in capillary pressure calculations, as water occupies this deeper layer. These calculated values, presented in Table 4, offer critical insight into the capillary-driven movement of paraffin across different roughness regimes and highlight how surface morphology and pore-scale geometry dictate wettability dynamics in synthetic porous media.Fig. 24Mechanism of paraffin droplet penetration into the surface roughness of a water-saturated synthetic thin section.Table 4Estimation of capillary pressures, gravitational pressure in the cavity and meniscus regions, and Bond number in the cavity region during paraffin droplet penetration into the surface roughness of the synthetic thin section.Glass beads radius (R) Micrometer (mesh)Paraffin-air capillary pressure (Pc) KPWater-paraffin capillary pressure (Pc) KPGravity pressure (Pg) KPBond number (Bo) Dimensionless354 (25)0.341.70.0320.094250 (35)0.472.30.0230.049200 (40)0.592.90.0180.031149 (50)0.7940.0130.016125 (60)0.954.60.0110.012105 (70)1.125.50.00950.00889 (80)1.347.80.0080.00675 (100)1.5680.00670.00463 (120)1.869.80.00570.003 Mechanism of paraffin droplet penetration into the surface roughness of a water-saturated synthetic thin section. Table 4Estimation of capillary pressures, gravitational pressure in the cavity and meniscus regions, and Bond number in the cavity region during paraffin droplet penetration into the surface roughness of the synthetic thin section.Glass beads radius (R) Micrometer (mesh)Paraffin-air capillary pressure (Pc) KPWater-paraffin capillary pressure (Pc) KPGravity pressure (Pg) KPBond number (Bo) Dimensionless354 (25)0.341.70.0320.094250 (35)0.472.30.0230.049200 (40)0.592.90.0180.031149 (50)0.7940.0130.016125 (60)0.954.60.0110.012105 (70)1.125.50.00950.00889 (80)1.347.80.0080.00675 (100)1.5680.00670.00463 (120)1.869.80.00570.003 Estimation of capillary pressures, gravitational pressure in the cavity and meniscus regions, and Bond number in the cavity region during paraffin droplet penetration into the surface roughness of the synthetic thin section. On fully hydrophilic surfaces such as clean glass, water exhibits dramatically different wetting behavior depending on the surrounding fluid. In the water–air–glass system, the high interfacial tension (~ 72 mN/m) between water and air, combined with the strong affinity of water for glass, leads to a near-zero contact angle, indicating complete wetting and the formation of a sharply concave meniscus. In contrast, when paraffin replaces air (water–paraffin–glass), although the glass remains hydrophilic, the contact angle increases to ~ 30°. This shift results from two primary factors: (1) the lower interfacial tension between water and paraffin (~ 51 mN/m), which reduces the wetting force, and (2) competitive surface interactions between paraffin and water at the solid interface, with water still dominating but paraffin partially affecting interface occupation. Consequently, while the meniscus remains concave, its curvature is less pronounced, reflecting the higher contact angle. This change in interfacial configuration illustrates the sensitivity of capillary pressure to the nature of the surrounding fluid phase—even for intrinsically hydrophilic materials. During paraffin droplet deposition onto the rough surface of the semi-immersed synthetic thin section, capillary and gravitational forces act simultaneously. These may interact constructively or antagonistically, depending on the direction of the curvature and depth of penetration (Fig. 24). To quantify this interplay, gravitational pressure was calculated using the roughness depth (either pore radius or throat radius) as the effective vertical length scale. These values, presented in Table 4, allow for comparison with capillary pressures calculated for both paraffin–air and paraffin–water systems. The dimensionless Bond number (Bo) was also computed, providing a normalized metric for evaluating the relative significance of gravitational versus capillary forces. The results confirm that capillary forces remain dominant in most cases, particularly in finer structures, but gravitational effects cannot be entirely neglected, especially when assessing droplet behavior on rough or inclined surfaces. The displacement of air trapped within the meniscus by paraffin is physically constrained by interfacial tension relationships between the involved phases. The key barrier lies in the significantly higher surface tension of the water–air interface (~ 72 mN/m) compared to the water–paraffin interface (~ 51 mN/m). This disparity results in a thermodynamically stable air phase within the meniscus, resisting spontaneous replacement by paraffin. The potential for fluid substitution is quantitatively assessed using the spreading coefficient (S), defined in44 Eq. (9), which predicts whether one liquid can spread and displace another at a given interface. In this system, the spreading coefficient for paraffin displacing air is calculated using the interfacial tensions of paraffin–air (~ 25 mN/m), water–air, and water–paraffin. The resulting negative spreading coefficient confirms that paraffin cannot spontaneously replace air within the meniscus under equilibrium conditions48. A positive spreading coefficient would indicate spontaneous spreading and displacement, but in this case, external forces (e.g., applied pressure or agitation) are required to overcome the energy barrier for substitution. This analysis emphasizes the interfacial energy constraints governing multiphase interactions in rough porous media and highlights why air entrapment persists in surface cavities during contact angle measurements, particularly when paraffin is used as the test fluid.9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{S}={\upsigma}_{\mathrm{w}\mathrm{a}\mathrm{t}\mathrm{e}\mathrm{r}-\mathrm{a}\mathrm{i}\mathrm{r}}-{\upsigma}_{\mathrm{w}\mathrm{a}\mathrm{t}\mathrm{e}\mathrm{r}-\mathrm{p}\mathrm{a}\mathrm{r}\mathrm{a}\mathrm{f}\mathrm{f}\mathrm{i}\mathrm{n} }-{\upsigma}_{\mathrm{p}\mathrm{a}\mathrm{r}\mathrm{a}\mathrm{f}\mathrm{f}\mathrm{i}\mathrm{n}-\mathrm{a}\mathrm{i}\mathrm{r}}$$\end{document} The inability of paraffin to spontaneously displace air trapped within the meniscus of a water-saturated glass bead porous medium stems from a combination of interfacial, physical, and thermodynamic constraints. First, the high contact angle of paraffin on hydrophilic glass surfaces in the presence of water inhibits its wetting of the bead walls, causing it to remain in discrete droplet form rather than spreading, thus failing to engage with the air–solid interface. Second, buoyancy effects further resist downward infiltration; with a density of ~ 800 kg/m3, paraffin tends to float, and external force is required for it to overcome this tendency and enter the meniscus cavities. Furthermore, paraffin’s relatively high viscosity (~ 3 cP) impedes its flow into the narrow throats of the porous medium, while the small throat radius (meniscus radius) results in high capillary pressure favoring air retention. Under these conditions, the air within the meniscus remains in a stable thermodynamic state, and paraffin lacks sufficient driving force to displace it. This is consistent with the negative spreading coefficient, indicating that paraffin cannot replace air without external energy input. To address this challenge, auxiliary techniques can be considered, such as:Applying external pressure (e.g., with a pump or needle),Heating the paraffin to reduce its viscosity and surface tension,Employing larger glass beads to increase throat size and lower capillary resistance, orChemically modifying the glass surface to enhance paraffin wettability. Applying external pressure (e.g., with a pump or needle), Applying external pressure (e.g., with a pump or needle), Heating the paraffin to reduce its viscosity and surface tension, Heating the paraffin to reduce its viscosity and surface tension, Employing larger glass beads to increase throat size and lower capillary resistance, or Employing larger glass beads to increase throat size and lower capillary resistance, or Chemically modifying the glass surface to enhance paraffin wettability. Chemically modifying the glass surface to enhance paraffin wettability. Absent these interventions, the combined effects of interfacial tension, buoyancy, viscosity, and capillary confinement prevent spontaneous air displacement. Therefore, during contact angle measurements or infiltration experiments with paraffin, air remains trapped within the meniscus region, as visually depicted in Fig. 25.Fig. 25Penetration of paraffin into the surface roughness of the artificial thin section, and air entrapment during paraffin penetration into the roughness. Penetration of paraffin into the surface roughness of the artificial thin section, and air entrapment during paraffin penetration into the roughness. Mechanism of paraffin droplet spreading on the surface of the artificial thin section The mechanisms and forces involved in the saturation of the artificial thin section with water, as well as the forces influencing the placement and penetration of a paraffin droplet into the surface roughness and pores, were examined. When a paraffin droplet is placed on the surface of the artificial thin section, there are mechanisms and forces that, in addition to acting in the vertical direction, also operate horizontally, leading to either the spreading or non-spreading of the paraffin droplet (Fig. 26). Typically, the adhesive forces between paraffin molecules and the rough surface determine whether the droplet tends to spread across the surface or prefers to maintain minimal contact. If the adhesion between the paraffin and the surface is stronger than the cohesive forces within the paraffin itself, the droplet will spread on the surface49. Conversely, if adhesion is weak (e.g., on hydrophobic surfaces), the droplet will retain a more spherical shape and will not spread. The cohesive forces between paraffin molecules cause the droplet to maintain its spherical form. In other words, the surface tension resulting from these cohesive forces resists spreading. The stronger the internal cohesion within the paraffin (e.g., in high–molecular-weight paraffins), the less the droplet will spread across the surface. Surface tension of the paraffin and the surface energy of the underlying substrate play a key role in spreading behavior. If the substrate has a high surface energy (such as hydrophilic surfaces), paraffin in the presence of water (which is generally hydrophobic to paraffin) may not spread. Conversely, if the surface is hydrophobic, spreading is more likely to occur. In addition, higher paraffin viscosity slows down molecular movement, reducing the spreading rate. Heavier paraffins (with higher viscosity) tend to maintain droplet shape, while lighter paraffins (with lower viscosity) spread more easily across the surface. These factors collectively determine the spreading behavior, and adjusting any of them can influence the outcome. Another highly significant factor in paraffin spreading is the degree of surface roughness.Fig. 26Mechanism of paraffin droplet spreading over the surface roughness of a water-saturated artificial thin section. Mechanism of paraffin droplet spreading over the surface roughness of a water-saturated artificial thin section. The pinning effect is an important phenomenon in surface science that occurs when the three phase contact line (the interface between the droplet, the solid surface, and the surrounding air) becomes locked in a specific position on a rough surface47,50. This phenomenon is primarily caused by the presence of microscopic irregularities, impurities, or variations in surface energy at different points on the surface. When a droplet attempts to move across the surface, these irregularities act like molecular hooks, preventing the free displacement of the contact line. The energy required to overcome these obstacles is often greater than the energy available within the system, causing the droplet to remain in a stable, pinned state. “Molecular hooks” refer to specific points on rough surfaces that, by generating strong localized adhesive forces, act like microscopic anchors, thereby inhibiting the movement of the three-phase contact line (liquid–solid–gas). These hooks can have either a physical origin51 —such as nanometric protrusions or micrometric cavities with specific geometries—or a chemical origin52, such as active functional groups or regions with different surface energies. From a physical perspective, such irregularities create local energy barriers that physically obstruct the displacement of the contact line. From a chemical standpoint, surface functional groups can form numerous weak interactions (such as van der Waals forces or hydrogen bonds) with the liquid molecules, thereby increasing the local adhesion energy. Each pinning point creates a localized energy well. In the pinning phenomenon, an energy well acts like an invisible pit that holds the droplet in place on the surface53 (Fig. 27a). When a droplet rests on a rough surface, every small protrusion or indentation acts as a trap, generating localized adhesive forces that lower the system’s energy at that point. These traps represent the energy wells that keep the droplet fixed in position. The deeper these energy wells are—that is, the stronger the adhesive forces or the more pronounced the physical barriers—the more difficult it becomes for the droplet to move. To remove the droplet from such wells, external energy must be supplied (e.g., by vibrating the surface or heating it). This process is analogous to trying to lift a ball out of a pit: the deeper the pit, the greater the force required. In nature, the lotus leaf provides one of the best examples of this phenomenon. The surface of the lotus leaf is covered with fine micro-protrusions that form numerous energy wells, preventing water droplets from moving freely and causing them to remain in a spherical shape. This mechanism is known as the Lotus effect54, which significantly influences fluid spreading behavior. The magnitude and intensity of the pinning effect depend on several factors. One of the most important is surface morphology. Surfaces with irregular and random roughness typically generate more pinning points. Additionally, chemical heterogeneity—such as the coexistence of hydrophilic and hydrophobic regions—can immobilize the contact line at specific locations. The properties of the liquid itself also play a significant role; liquids with high viscosity, such as paraffin, are more susceptible to pinning due to reduced molecular mobility. This phenomenon also leads to contact angle hysteresis, where the advancing and receding contact angles exhibit different values.Fig. 27Pinning effect and droplet volume effect in rough surface models (a), and the absence of contact angle variation with different volumes in the Young model (b). Pinning effect and droplet volume effect in rough surface models (a), and the absence of contact angle variation with different volumes in the Young model (b). According to Young’s theory, on smooth and homogeneous surfaces, droplet volume has little to no significant effect on the contact angle. As droplet volume increases, the wetted area expands proportionally, maintaining a constant contact angle (Fig. 27b). However, on rough and heterogeneous surfaces (such as rocks or fracture morphology), droplet volume can influence the contact angle by altering the balance between surface tension and gravitational forces, contact line pinning, and infiltration into surface roughness. Larger droplet volumes may drive the contact angle toward equilibrium values consistent with the intrinsic wettability of the surface. Conversely, smaller droplets, due to stronger pinning effects and roughness constraints, may exhibit anomalous contact angles (either larger or smaller than expected). Droplet behavior on rough surfaces typically follows two primary wetting states: Wenzel state: The liquid fully penetrates the surface cavities (Fig. 28a). Larger droplet volumes, with improved infiltration, reinforce this state. Cassie–Baxter state: The liquid rests on the asperity peaks while air remains trapped beneath it (Fig. 28b). Although this state is commonly associated with hydrophobic surfaces, it can also occur on highly rough hydrophilic surfaces. Small droplets may remain stable in the Cassie–Baxter state, while larger droplets, due to greater weight, tend to transition into the Wenzel state. On hydrophilic surfaces, roughness usually enhances wettability (Wenzel state), since the droplet tends to sink into the valleys and display a lower contact angle compared to a smooth surface. However, if the roughness is sufficiently deep to trap air pockets (Cassie–Baxter state), the contact angle can increase. Factors such as slower spreading rates during transition through the depinning threshold, higher roughness depth-to-width ratios, elevated viscosity and interfacial tension of paraffin, and the presence of recessed or closed-pore structures can prevent complete infiltration of paraffin into the porous surface of the thin section, resulting in air entrapment within the roughness. In such cases, wetting behavior shifts from the Wenzel model toward the Cassie–Baxter regime. Therefore, in the Wenzel state, the paraffin droplet tends to fully penetrate the roughness, emphasizing vertical infiltration. In contrast, in the Cassie–Baxter state, the paraffin droplet prefers minimal penetration, resting primarily on asperity peaks, which promotes horizontal spreading of the liquid. Furthermore, if the surface roughness is low and the porous medium is constructed using very fine glass beads, the pore size on the surface of the artificial thin section becomes extremely small. In this case, capillary action through water rise and imbibition can partially cover the surface roughness. As a result, the paraffin droplet cannot penetrate all the surface asperities. Consequently, the wetting behavior shifts from the Wenzel model toward the Cassie–Baxter model (Fig. 28c). This condition is analogous to a situation in which air is trapped within part of the surface roughness, making it impossible to describe the wettability solely using the Wenzel state. In other words, under various roughness conditions and when employing the partial immersion method to saturate the artificial thin section with water, a transition in wettability can occur—from the Wenzel state to the Cassie–Baxter state.Fig. 28(a) Illustration of the Wenzel model on a rough, hydrophilic surface; (b) description of the intermediate state between the Wenzel and Cassie–Baxter models on a rough, hydrophilic surface with trapped air; and (c) with trapped water. (a) Illustration of the Wenzel model on a rough, hydrophilic surface; (b) description of the intermediate state between the Wenzel and Cassie–Baxter models on a rough, hydrophilic surface with trapped air; and (c) with trapped water. Conclusions This study establishes a foundational framework for the deterministic engineering of surface roughness in porous media. By transitioning from the inherent stochasticity of natural rocks to a precisely controlled platform of sintered glass beads, we have demonstrated that surface topography can be transformed from an uncontrolled variable into a programmable design parameter. Our methodology reveals unambiguous scaling laws between particle size and roughness metrics (Rₐ and r), enabling the predictable fabrication of surfaces spanning a spectrum from low-amplitude, high-frequency textures to high-amplitude, wavy undulations. The power of this platform is demonstrated through its ability to resolve long-standing interfacial complexities. The innovative semi-immersion technique unlocks reliable contact-angle measurement on porous surfaces, revealing how specific roughness scales mechanistically govern wetting state transitions between Wenzel and Cassie-Baxter regimes. Furthermore, we directly link contact-line pinning—a direct consequence of engineered micro-topography—to the macroscopic phenomena of contact-angle hysteresis and capillary trapping. This provides empirical validation of the “roughness space” concept, where the coupled geometry of the solid and the fluid meniscus dictates local capillary pressures and trapping efficiency. From a practical standpoint, this platform offers a direct pathway to tailor multiphase flow functions—including capillary pressure curves and relative permeability—by strategically selecting bead size and packing architecture. This capability has immediate implications for optimizing processes such as enhanced oil recovery and geological CO₂ storage, where residual trapping is paramount. Looking forward, the implications of this work extend far beyond subsurface applications. This versatile and reproducible testbed provides a new paradigm for the fundamental study of disorder, capillarity, and transport. It opens avenues for designing biomimetic surfaces, optimizing catalytic reactors, engineering advanced filters, and calibrating next-generation digital rock models. By providing a missing link between theoretical models and experimental validation, our platform empowers a new era of deterministic design in porous media science.