Inductor-capacitor gain cell-based non-isolated high step-up converter for DC microgrid Authors: M Prabhakar, Amaleswari Rajulapati, A Sudha, R Arul Published: 2026 ABSTRACT AbstractIn this paper, a high-gain DC-DC converter with an ultra-step-up voltage gain value of 20 is introduced. The proposed converter is synthesized using two stages – stage 1 yields a voltage gain which is double that of a classical boost converter (CBC) and stage 2 employs an inductor-capacitor gain cell (ICGC) to obtain a quadratic voltage gain function. Since a voltage gain extension technique is employed, the voltage stress on the switches in stage 1 is significantly reduced. The proposed gain extension hypothesis is experimentally validated through a 20 V to 400 V, 200 W prototype converter that operates at 94.5% full-load efficiency. The proposed converter regulates the output voltage to 400 V over a wide range of input voltage and load current variations with minimal overshoots and undershoots. Further, the maximum voltage stress on two switches switch is only 10% of the output voltage. Due to the interleaved mechanism employed in stage 1, the input current is smooth and ripple-free. Based on the comparison with several state-of-the converters, the unique advantages of the proposed converter are clearly validated and found suitable for DC microgrid application.Keywords: DC-DC converters, Power conversion, Power electronics, DC microgridsSubject terms: Energy science and technology, Engineering Introduction The tangible contribution and penetration of renewable energy sources (RES) such as photovoltaic (PV) systems, wind energy conversion systems (WECS), and fuel cells along with battery-based energy storage system (BESS) has accelerated the development of DC microgrids and DC distribution systems1,2. DC microgrids eliminate multiple AC–DC conversion stages. Hence, the intermediate power losses are reduced besides improving the system reliability. However, the inherently low and variable nature of most RES necessitates the deployment of intermediate power electronic converters. To meet the high-voltage requirement of the DC bus and loads, high step-up DC–DC converters are essential3. Conventional non-isolated DC–DC converters suffer from limited voltage gain, high switch voltage stress, increased duty cycle operation, and degraded efficiency when high conversion ratios are required. Hence, the research focus is on developing novel non-isolated high step-up DC–DC converters that yield large voltage gain at safe duty-ratio values. Various voltage gain extension techniques viz., switched capacitor (SC) cells, switched inductor (SI) structures, voltage-lift networks, and coupled inductors (CI), are reported in literature4–7. Generally, single-switch-based converters adopt cascaded and clamped structures to enhance the net voltage gain of the converters8–10. Such structures reduce the device stress and improve the overall power transfer capability. In the converters that employ SC and voltage-lift networks, higher input current ripple and capacitor stress are common11–13. Interleaving technique addresses the input current ripple issue. In fact, the input current can be made free from ripples by operating the switches with appropriate phase-shift and duty ratios14–16. To achieve ultra-high voltage gain values of the order of more than 15, CIs with appropriate turns ratio are employed along with appropriate gain-extension mechanisms17–23. These CI-based converters possess ultra-high voltage gain at safe duty cycle values. However, the leakage inductance introduces voltage spikes across the switches and cause electromagnetic interferences. Nevertheless, by using suitable energy-recycling circuits, the voltage spikes are reduced. By carefully synthesizing CI-based topologies, converters with quadratic and high-order gain capabilities are realized. They have gained significant attention due to their ability to achieve voltage gain values that are proportional to the square or higher powers of the duty cycle24,25. To obtain ripple-free input current while simultaneously achieve high voltage gain values, interleaved versions of the quadratic and higher order converters are proposed in26–30. These converters are well-suited for high step-up applications even at safe duty ratio values. Advanced quadratic converter versions that employ interleaved structures along with gain extension mechanisms are proposed to improve voltage gain, efficiency, and power density31–37. However, many existing designs still face challenges related to increased component count, control difficulty, higher voltage stress on some of the components, and limited scalability for DC microgrid applications. The converter proposed in this paper is motivated by the aforementioned challenges. The proposed converter aims to achieve ultra-high voltage gain with reduced semiconductor voltage stress, continuous and low-ripple input current, and improved efficiency. The proposed converter maintains a compact structure and employs a simple control strategy. The synthesis mechanism, its operating principle, detailed steady-state analysis, the experimental validation, and the comparison sections that are presented subsequently demonstrate the effectiveness and practical applicability of the proposed topology for DC microgrid application. Power circuit diagram of the proposed converter The power circuit of proposed high gain converter is shown in Fig. 1. The proposed converter is based on the inductor-capacitor gain cell (ICGC) to provide high gain. Stage 1 has a two-phase interleaved boost converter (IBC) along with voltage-lift (VL) cell. The discrete inductors L1 and L2 are part of IBC and VL cell comprising of D1 and CLift. In stage 2, the ICGC structure is connected in series with stage 1 to enhance the output of previous stage. Thus, the required voltage gain at the output capacitor C0 is achieved. It consists of inductor L3, diodes D3, D4, D5, and capacitors C1, C2, and C3. This switching-capacitor-based ICGC structure is derived from a boost and a buck/boost converter configuration. Hence, a series arrangement of C3 acts as an output capacitor for boost structure and C2 acts as an output capacitor for buck/boost structure. This gives rise to a higher voltage gain during specific switching intervals. Capacitor C0 is the output of the proposed converter. The operating principle is described subsequently. Circuit diagram of the ICGC-based high gain converter. Operating principle The proposed converter consists of three power switches S1, S2, and S3 operating synchronously. Its operation is understood by considering four modes viz., the ON and OFF periods of the power switches while the following valid assumptions aid in easily comprehending the operation. (i)All switching elements are ideal. All switching elements are ideal. (ii)All the inductors operate in continuous conduction mode (CCM) and the converter draws continuous input current. All the inductors operate in continuous conduction mode (CCM) and the converter draws continuous input current. (iii)All the inductors are pre-charged. All the inductors are pre-charged. Mode 1 (0 to t1) Mode 1 commences when the power switches S1 and S3 are turned ON simultaneously at t0 and S2 is turned OFF. The inductor L1 and L3 are linearly charged by the voltage source through S1 and S3 respectively. The current paths are given by Vin – L1 – S1, Vin – L2 – Clift – D2 – L2 – S3 respectively. Diode D1 is reversed-biased due to the negative voltage developed across capacitor CLift. The inductor L2 discharges and transfers its stored energy along with the pre-charged energy of CLift, C1, and C2 through diode D2. Diode D4 is thus forward-biased and capacitor C0 charges. Since S3 is ON, L3 charges and C3 discharges. The governing equations during this mode are given by (1)–(3). Figure 2a portrays the equivalent circuit during mode 1. (a) Mode 1 equivalent circuit of the proposed ICGC. (b) Equivalent circuit of the proposed ICGC during Mode 2. (c) Mode 3 equivalent circuit of the proposed ICGC. (d) Mode 4 equivalent circuit of the proposed ICGC. Mode 2 (t1 to t2) During mode 2, S1 continues to be ON and S2 remains OFF at t1. At t1, S3 is turned-OFF. Inductor L1 continues to charge through the S1. Inductor L2 and CLift continue to discharge into C1 and C3 through D2. The stored energy in L3 is transferred to C3. Now C3 charges and D5 is forward-biased. Inductor L3 discharges into C2 through D3. The output capacitor C0 meets the load requirement. Equations (4)–(6) are valid during mode 2. The equivalent circuit of mode 2 is presented in Fig. 2b. Mode 3 (t2 to t3) Mode 3 starts when S1 is turned OFF and S2 and S3 are turned ON at t2. Inductor L1 starts to discharge and charges CLift through D1. Inductor L3 charges through S3. Capacitor C1, C2 discharge into C0 and load through D4. As S2 is ON, L2 starts to charge S2. The equations during mode 3 are presented in (7)–(9) and Fig. 2c presents the equivalent circuit. Mode 4 (t3 to t4) Mode 4 commences when S1 continues to remain OFF and S2 remains in the ON state. Switch S3 is turned-OFF. The current paths for inductors L1 and L2 are same as mode 3. Inductor L3 continues to transfer its stored energy to C3 and C2 through D3. The output capacitor C0 meets the load demand. The switching cycle ends at t4 when S1 is turned ON again. The governing equations are presented through (10)–(12). Figure 2d presents the equivalent circuit during mode 4. The characteristic waveforms are portrayed in Fig. 3. Characteristic waveforms of the ICGC-based converter. Voltage conversion and design equations In this section, the voltage conversion ratio of the proposed ICBC is derived along with other key design equations viz., voltage and current ratings of the switching elements, and ratings of the passive elements. Voltage conversion ratio The voltage gain expression of the proposed ICGC is deduced by applying volt-second balance across the inductors during turn ON and OFF periods. Stage 1 comprises of IBC with a voltage-lift capacitor. This arrangement doubles the output of a CBC. Therefore, the effective voltage gain developed across stage 1 is given by (13). where δ1 is the duty ratio of S1 and S2. In the second stage, C3 acts as the output capacitor of boost structure and C2 provides the output of buck/boost structure. The overall output is obtained across C0. Thus, stage 2 gain is expressed using (14). where δ2 is the duty ratio of S3. The overall voltage gain contributed by the two stages is obtained from (13) and (14) and given by (15). When all the three switches are operated at the same duty ratio, a quadratic voltage gain profile is obtained. Thus, the proposed ICGC provides an ultra-high voltage conversion ratio. Rating of switching elements In the proposed ICGC converter, the power switches operated in the interleaved legs. Therefore, these switches experience stress like the CBC and given by (16). The current stress of S1 is determined when it is conducting during mode 1 and mode 2. As L1 charges through S1 and the input current is shared by the two interleaved phases, its current stress is given by (17). When S2 is turned ON, L1 transfers its energy to CLift through S2. Inductor L2 also charges through S2. Hence, its current stress is relatively higher that of S1 and it is given by (18). Due to the location of S3, it is subjected to a higher voltage stress. Nevertheless, since only a partial gain extension occurs in stage 2, its voltage stress is relatively reduced and given by (19). The current through L3 and C3 add up and pass through S3. By applying KCL during the ON time (TON), the expression for current through L3 is given by (20). The diodes experience voltage stress when operating in reverse-biased condition. Diode D1 is reversed-biased during mode 1 and mode 2; its anode is clamped to the ground by S1 and its cathode is connected to CLift. Hence, its voltage stress is given by (21). Diode D2 is reversed-biased when S2 is turned ON. Based on the potential of its cathode and anode terminals, its voltage stress is given by (22). Diodes D1 and D2 carry the currents that flow through L1 and L2 respectively, Hence, their current stress level is given by (23) and (24). The anode of D3 connects to ground through S3 during TON. Its cathode voltage is realized as the sum of voltage across C1 and C2. Using KVL, the voltage stress expression is obtained and given by (25). During mode 2 and mode 4, D4 is OFF. Its cathode terminal is connected to the positive of the output port. Its negative terminal is connected to the positive terminal of C2. Thus, its voltage stress is deduced and given by (26). The anode terminal of D5 is connected to the negative plate of C3 during mode 1 and mode 3. Its positive plate is connected to ground through S3. Therefore, the voltage stress across D5 is same as voltage across C3 and given by (27). In mode 2 and mode 4, D3 and D5 are forward-biased. They carry the currents that flow through L3. Therefore, their current stress is given by (28). Design of passive elements In boost-derived converters, the inductor value is calculated by considering the duty cycle (δ), the voltage across each inductor (vL, ON), the switching frequency (f), and the allowable current ripple (ΔiL). In the proposed ICGC converter, there are two duty ratios and three inductors. Their values are computed using (29). For CCM operation, the actual value of the inductors must be more than the critical inductance (Lx−critical) that is expressed using (30). where RLoad is the load resistance value. The values of the capacitors are determined based on the ripple voltage impressed across the individual capacitors and the current that passes through them. The capacitance value of CLift is given by (31). The other capacitances are obtained from (32). Results from the hardware prototype converter and discussion To verify the effectiveness of the proposed gain mechanism, an ICGC prototype is developed and tested. Photographs of the experimented prototype and its corresponding laboratory setup are shown in Figs. 4 and 5, respectively. The specifications are summarized in Table 1 The components used in the prototype are presented in Table 2 The gating signal and closed-loop control algorithm are realized by suitably programming the STM32F411RE nucleo-64 microcontroller. For driving the power switches and ensure proper isolation, three FOD3180 opto-coupler driver circuits are supplied from an isolated DC source. Photograph of the tested prototype ICGC. Photograph depicting the experimental setup. Table 1Specifications of the proposed converter.ParameterValueInput voltage (Vin)20 VOutput voltage (V0)400 VSwitching frequency (fs)50 kHzDuty ratio of S1, S2 (δ1)0.508Duty ratio of S3 (δ2)0.6Output power (P0)200 WInductor current ripple (ΔiL)25% of iLCapacitor voltage ripple (Δv)1% of vc Specifications of the proposed converter. Table 2Components used in the prototype converter.Circuit elementDevicePart numberSwitches (S1, S2)MOSFETDMT10H9M9SCT (100 V, 99 A, 8.8 mΩ)Switch (S3)MOSFETIRF4668 (200 V, 130 A, 8 mΩ)Diodes (D1, D2)Fast recovery diodeSTTH2002 (200 V, 20 A, 0.86 V)Diodes (D3, D4, and D5)Fast recovery diodeBYV29-400 (400 V,9 A, 1.03 V)Inductors (L1)Ferrite corePCV2-104–10 L (100 µH, 10 A)Inductor (L2)Ferrite corePCV2-224–05 L (564 µH, 6 A)Inductor (L3)Ferrite corePCV2-564–06 L (564 µH, 4 A)Capacitors (C1 C2, C3)Polypropylene107CKE20 0 M (4.7 µF, 250 V)Capacitors (C4, C0)ElectrolyticEEUED2W 470 (47 µF, 450 V) Components used in the prototype converter. The converter’s voltage gain capability is validated through Fig. 6a,b. Figure 6a shows the gating pulses applied to S1 and S2 (CH1 and CH2 respectively). The converter operates from 20 V DC input (CH3). At the output, 400 V is realized as confirmed by CH4. Thus, the nominal voltage gain of 20 is practically confirmed. Switches S1 and S2 operate synchronously at 50.8% duty ratio with a phase shift of 180° to eliminate the input current ripple. The slightly raised duty ratio offsets the voltage drop across the semiconductor devices and passive components. Experimental results to validate the voltage gain hypothesis of the proposed ICGC. (a) CH1-gate pulse to S1, CH2-gate pulse to S2, CH3-Vin, CH4-V0 (b) CH1-gate pulse to S3, CH2-voltage across S3, CH3-Vin, CH4-V0. Figure 6b depicts the gate pulse oscillograms of S3 (CH1) and voltage across S3 (CH2) along with the input and output voltages (CH3 and CH4) respectively. Switch S3 is operated at δ2 = 0.6 to obtain the required voltage gain. As observed from the waveforms, the required output voltage of 400 V is obtained across the load. Figure 7 confirms the proper operation and the voltage stress of the power switches. The oscillograms in CH1, CH2, and CH3 confirm that they operate synchronously at 50 kHz. Further, S1 (CH1) and S2 (CH2) experience 40 V as their voltage stresses. These values match closely with the analytical values obtained using (16). In terms of V0, the stress value is 10% of V0. Since they are used in stage 1, their voltage stress is very less. The oscillogram shown in CH3 confirms that S3 endures a higher voltage stress of about 200 V (50% of V0) due to its position. Nevertheless, since 2 out of 3 switches experience only a voltage stress i.e. 10% of V0, MOSFETs with lower ON-state resistance (RDS−ON) may be employed to reduce the overall losses. Experimental waveforms to verify the switch operation and their voltage stress levels. CH1, CH2, and CH3 – voltage across S1, S2, and S3 respectively, CH4 – V0. The waveforms presented in Fig. 8a demonstrate the gain mechanism of the ICGC stage. The voltage waveforms shown in CH2 and CH1 confirm the coordinated operation of S1 and D1. The voltage across S2 and D2 is represented by the voltage waveforms seen in CH4 and CH3, respectively. As a result, their functionality is confirmed and they also work in tandem with one another. Furthermore, measurements show that the voltage stress levels across D1 and D2 are 105 V and 37 V, respectively. The practical values closely match with the analytical counterparts. Interestingly, D1 receives a voltage stress equal to the voltage created across capacitors CLift, whereas D2 experiences a voltage stress that is exactly the same as that of S1. Oscillograms to verify the operation of the semiconductor devices (a) CH1, and CH3 – voltage stress across D1 and D2 respectively, CH2, and CH4 – voltage across S1, and S2 respectively and (b) voltage stress on the S3 and the diodes CH1 – S3, CH2, CH3, and CH4 – voltage stress of D3, D4, and D5 respectively. Figure 8b portrays the operation of the diodes employed in stage 2 which is the ICGC. The operation of the diodes D3, D4, and D5 is correlated with S3. Since D3 and D4 exist within the ICGC, their operation is complementary as verified from oscillograms in CH2 and CH3. Diode D5 acts like a boost-rectifier diode in the CBC. Hence, its operation is complementary to the power switch S3 as verified from CH3 and CH4 oscillograms. Diodes D3, D4, and D5 are subjected to a voltage stress value of 250 V (62.5% of V0); the value agrees with the predicted analytical result. Figure 9 illustrates the current through the inductors (CH1, CH2, and CH3) under nominal conditions along with the input current (CH4). Based on the operating principle the current through L1, L2, and L3 is shared based on the duty ratio. The magnitude of the input current waveform depicted in CH4 is about 10.45 A. Examination of the waveform portrayed in CH1 reveals that the current through L1 is approximately 5.3 A which closely aligns with the theoretical value. The waveforms displayed in CH2 and CH3 represent the current through L2 and L3, respectively. When the converter operates at a 50.8% duty ratio, the current stress through L2 and L3 should be identical. To compensate for voltage drops across switching elements, the ICBC is run at a slightly higher duty ratio of D = 0.6, which results in a slightly larger current through L2 (2.75 A) than via L3 (2.63 A). The suggested ICGC is noteworthy for its approximately halving of the maximum current stress on the inductor. Experimental waveforms to demonstrate inductor currents. CH1 – Iin, CH2, CH3, and CH4 – current through L1, L2, and L3. Figure 10a presents the measured efficiency of the ICGC prototype under full load condition. When supplied from an 18 V input (CH1), the converter produces 175 W at 400 V (CH3). The converter extracts 10.39 A from the input port based on the input current waveform (CH2). The calculated operating efficiency value is 93.5%. The converter runs at a reasonable efficiency value under nominal load conditions because stage 1 switches and diodes with low voltage ratings are used, and the inductors have fewer stray-resistive losses. Practical waveforms to compute the efficiency value under (a) full-load (175 W), (b) light load (195 W) and (c) overload (135 W) conditions. CH1 – Vin, CH2 – Iin, CH3 – V0, and CH4 – I0. Figure 10b provides the efficiency value of the suggested converter under overload conditions. The output voltage decreases to 389 V (CH3) when the load resistance is lowered to 776 Ω because of the increasing load. With an efficiency of 87.7%, the converter provides the load with 195 W of power. The ICGC’s somewhat lower efficiency figure is caused by a greater voltage drop across its components. Since quadratic losses become substantial and lower overall efficiency under greater load circumstances, the decrease in efficiency value is expected. The suggested converter’s practical efficiency under light load is shown in Fig. 10c. At 409 V, the converter produces 135 W of output power. The decreased voltage drop is the cause of the output voltage’s small increase. Typically, traditional boost-derived converters exhibit such a behaviour under open-loop condition. Figure 11 portrays the efficiency curves of the proposed ICGC under both simulated and practical conditions. The practical efficiency values match very closely with each other and the minor deviations are due to the stray losses associated with the passive elements. The output voltage variation for various load power levels under open-loop conditions is also plotted in Fig. 11. The output voltage variation remains within 5% of V0 when the load varies between 135 W and 195 W. Thus, the robust operation of the proposed converter in handling significant load variations while maintaining stable output voltage is demonstrated. Plot of the simulated and practical efficiency curves under various load conditions correlated with the output voltage waveforms. The loss across various active and passive components are computed using the standard expressions provided in (33)–(35). Figure 12 shows the loss distribution profile of the proposed converter. The diodes contribute to a major share of the total losses (52.5%) of the total power loss. The efficiency of the proposed ICGC is computed using (36). Loss distribution profile of the proposed ICGC. The dynamic performance of the proposed ICGC is examined by implementing closed-loop control. A potential divider-based network reduces the output voltage to a safer level (< 3.3 V) that sis fed as input to the in-built analog-to-digital converter (ADC). The filtered ADC output is used to obtain the error signal by comparing with the reference voltage corresponding to 400 V. This error signal is fed into a discrete-time proportional controller with lower and upper saturation values on duty ratio. The controller is suitably tuned to provide a swift response with minimal overshoot and undershoot. Figure 13a shows the line voltage regulation characteristics of the proposed converter. The input voltage is varied in a stepped manner ranging from 13.4 V to 21.3 V to replicate the PV panel behavior. Under this condition, the implemented closed-loop algorithm effectively restores the output voltage back to 400 V very quickly with minimal undershoots and overshoots. In the process of restoring the output voltage to 400 V, the converter yields a maximum voltage gain of 30. The load regulation characteristics of the ICGC are portrayed in Fig. 13b. The proposed ICGC regulates the output voltage over a wide range of load current which varies from 360 mA to 512 mA. In terms of power level, the proposed converter regulates the output voltage to 400 V when the load varies from 144 W to 205 W. Thus, the converter’s versatility and robustness in handling wide load current and line voltage variations is practically validated. Further, the suitability of the proposed converter for an actual PV-fed DC microgrid is validated through the excellent dynamic performance. Experimental waveforms to verify the (a) line voltage and (b) load current regulation profiles. CH1 – Vin, CH2 – Iin, CH3 – V0, and CH4 – I0. Benchmarking of the proposed ICGC with some existing converters The proposed ICGC is compared with some similar state-of-the art converters available in recent reputed literature. Table 3 depicts the comparison attributes and the converters. The proposed ICGC is compared with quadratic variants to showcase its salient features. Table 3Comparison of the proposed ICGC with similar converters.AttributesConverter presented in 26 27 33 35 36 37 Proposed ICGC V in 1824201240 V48 V20 V 0 38038019085 V250 V320 V400 M 21.1115.839.57.226.256.9420 D D1=0.5D2=0.620.650.420.40.60.30.508 N Mag 52 CIs22223 N S 3222113 N D 7654365Total components used (TCU)1914141281416 M/TCU 1.141.130.680.60.780.5/0.481.39Switch voltage stress (% V0)VS1,2=18.9VS3=100VS1,2=50VS1,2=17.4VS1 = 55.3VS2 = 23.594.450VS1,2=9.25 VS3=50NMag – No. of magnetic elements, NS – no. of switches, ND – no. of diodes. Comparison of the proposed ICGC with similar converters. D1=0.5 D2=0.62 VS1,2=18.9 VS3=100 VS1 = 55.3 VS2 = 23.5 NMag – No. of magnetic elements, NS – no. of switches, ND – no. of diodes. Voltage gain and duty ratio The converters presented in26 and27 yield impressive voltage gain amplification. However, the converters in33,35–37 yield a voltage gain of 9.5 and lower with an average duty ratio of 0.4. The proposed converter yields highest gain of 22.22 at 50% duty utilising components similar to converters compared in the literature. The converter presented in26 delivers the second highest gain of 21.11, at a high duty ratio of 50% and 62%. This performance is closely followed by the converter in27, which achieves a voltage gain of 15.83 at 0.65 duty ratio. Thus, the proposed ICGC operates with a superior voltage gain capability. Figure 14 portrays the voltage gain plots of the converters compared in Table 3. Voltage gain plot of all the compared converters. Total components used (TCU) and M/TCU ratio To gain a deeper understanding of all the converters’ performance, it is essential to factor in the number of components utilized in them. The M/TCU ratio serves as a comparative metric. The proposed converter has highest M/TCU of 1.39 operated at 0.5 duty. The converters presented in26 and27 yield the second highest and third highest M/TCU ratio of 1.14 and 1.13 respectively. However, they operate at slightly higher duty ratio values. The converter presented in37 has the lowest M/TCU value of 0.5. The M/TCU of converters present in [33 and 35] is less than 1 but they are operated at a bit lower duty ratio of 0.4. The M/TCU of converter present in36 is still less than 1 though it is operated at higher duty ratio of 0.6. Voltage and current stress on the switch The proposed converter and the converter detailed in reference26 both use three power switches. This distinguishes them from most of the other compared converters, which typically employ two power switches while27,33,35 uses single switch. The maximum voltage stress on the switches S1,2 = 9.25% is the least in proposed ICGC and switch present in converter33 has 17.4% followed by switch of converter in26 having 18.9% voltage stress on S1. The switches present in27,35,37 has 50% voltage stress. The single-switch used in36 experiences the highest stress of 94.4%. Due to the interleaving structure, half of the input current is carried by power switch 1 and full input current is carried by S2 for the proposed ICGC. However, its conduction loss is greatly decreased because of its low voltage stress (9.25% of V0). Hence, the proposed converter is a good candidate alternative for integrating the low voltage PV input even in high-power applications. Non-ideal voltage gain of the proposed ICGC The expression for the practical voltage gain of the proposed ICGC is obtained by considering the following non-ideal elements: (i) ON-state voltage drop of the diodes (VFD) and their ON-state resistance (RD), (ii) ON-state resistances of the MOSFETs (RDS−ON), (iii) stray resistances of the inductors (RL), and (iv) the equivalent series resistances of the capacitors (RC). Figure 15 portrays the equivalent circuit of the non-ideal ICGC. The practical voltage gain expression is derived by considering one non-ideality at a time and summarizing the effects finally. Firstly, the voltage gain expression is derived while considering the non-ideality in the diodes and given by (37). Equivalent circuit of the ICGC with all non-ideal elements. After including the non-ideality in the MOSFETs, the voltage gain expression is derived and expressed using (40). By including the stray resistance of the inductors, the voltage gain expression of the proposed ICGC is obtained as given in (42). Due to the stray capacitor resistance is included and the voltage gain expression is modified as shown in (44). The voltage drops due to all the non-ideal elements are summarized using (37)–(45). Thus, the practical voltage gain (Mpractical) is expressed using (46). Conclusion This paper presented a high-gain DC–DC converter capable of achieving an ultra-step-up voltage gain of 20. The converter was synthesized using a two-stage architecture. In stage-1, an interleaved boost converter with a voltage lift capacitor was employed. In stage-2, inductor-capacitor gain cell was adopted to extend the voltage gain. Thus, the proposed voltage gain extension technique effectively reduced the switch voltage stress. The proposed concept was experimentally validated through a 20 V to 400 V, 200 W prototype. Under full-load conditions, the converter operated at 94.5% efficiency. Further, due to the interleaving technique, the input current was free from ripples. The converter exhibited swift dynamic performance under wide input and load variations. Due to the gain extension mechanism, the maximum voltage stress on the switches was limited to 10% of the output voltage. Compared to similar state-of-the art converters, the proposed topology is superior in terms of its voltage gain capability, lower switch stress, and modularity. Thus, the proposed converter is expected to be a promising solution for DC microgrid and renewable energy integration applications. Acknowledgements This work has been published as an Indian Patent (Patent number 202441006474 A). This work was carried out using the Seed Grant SG20220010 provided by Vellore Institute of Technology, Chennai, India. The corresponding author thanks VIT for providing “VIT RGEMS Seed Grant.” Author contributions M. P – Conception, design of the work, analysis, interpretation of data, drafting the work, reviewing and supervisionA. R – Conception, analysis, interpretation of data, drafting the workA. S, R. A – Interpretation of data, and reviewingAll authors reviewed the manuscript. Funding Open access funding provided by Vellore Institute of Technology. This work was funded by Vellore Institute of Technology, Chennai, India through the Seed Grant SG20220010. Data availability All data generated or analysed during this study are included in this published article. Declarations Competing interests The authors declare no competing interests. Footnotes Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References Associated Data Data Availability Statement All data generated or analysed during this study are included in this published article.