Manganese Oxide Catalysts for Lithium–Oxygen Batteries: Structures, Mechanisms, and Reaction Pathway Engineering Authors: Ruiqin Peng, Linna Dai, Karol Viviana Mejia‐Centeno, Malik Dilshad Khan, Guifang Zeng, Yanhong Tian, Andreu Cabot, Qing Sun Published: 2026 ABSTRACT ABSTRACTThe growing demand for high‐specific‐energy storage has revived interest in lithium‐oxygen batteries (LOBs), whose theoretical energy density far exceeds that of conventional lithium‐ion battery systems. However, their practical use is limited by sluggish reaction kinetics, parasitic reactions, high overpotentials, and the buildup of insulating lithium peroxide, all of which hinder reversibility and cycling stability. Manganese oxides (MnOx) have emerged as promising cathode catalysts because of their abundance, low cost, tunable oxidation states, and diverse structural features. Their tunnel, layered, and spinel architecture provide adaptable environments for O2 reduction and evolution, Li+ transport, and the conversion of reaction intermediates. Recent progress demonstrates that structural engineering of MnOx, through pore‐structure tuning, surface‐site modulation, defect introduction, heteroatom doping, and composite fabrication, can significantly optimize lithium peroxide formation and decomposition. These strategies regulate catalyst electronic structures and reaction pathways, thereby influencing Li2O2 formation/decomposition behavior, reducing side reactions, lowering polarization, and enhancing catalytic activity. This review summarizes recent advances in MnOx‐based catalysts for non‐aqueous LOBs, emphasizing structure‐activity relationships and mechanistic understanding. By outlining remaining challenges and key design guidelines, we aim to support the rational development of next‐generation catalysts for practical LOB deployment.Keywords: catalysts, lithium‐oxygen batteries, manganese oxides, oxygen evolution reaction, oxygen reduction reaction Introduction With the accelerating demand for high‐specific‐energy storage systems driven by portable electronics [1, 2, 3, 4, 5], electric vehicles [6, 7, 8, 9], and large‐scale grid applications [10, 11, 12, 13], emerging rechargeable battery technologies that transcend the energy‐density limit of conventional lithium batteries have attracted extensive attention [14, 15, 16, 17]. Among these candidates, lithium‐oxygen batteries (LOBs), employing metallic Li as the anode and O2 as the cathodic reactant, stand out due to their gasoline‐comparable theoretical energy density [18]. Nevertheless, the practical implementation of LOBs remains severely constrained by several intrinsic bottlenecks. The charge/discharge process involves heterogeneous reactions across solid–liquid–gas interfaces. The primary discharge product, Li2O2, is insoluble and electronically insulating in organic electrolytes [19]. Consequently, uncontrolled accumulation of Li2O2 readily blocks cathode pores, passivates reaction interfaces, elevates polarization, and drastically shortens cycle life [20]. These challenges collectively undermine the energy efficiency and durability required for practical deployment, thereby hindering further advancement of LOB systems [21]. Since Littauer et al. first proposed the concept of LOBs in 1976 [22], their architecture and reaction environment have undergone continuous refinement. Early aqueous configurations suffered from severe safety issues due to the vigorous reactivity between metallic Li and water, limiting their applicability. It was not until 1996 that Abraham et al. introduced a rechargeable non‐aqueous LOB system employing a solid polymer electrolyte membrane [23], marking a major milestone in the field. Subsequently, in 2006, the Bruce group employed in situ mass spectrometry to confirm the reversible decomposition of Li2O2 into Li and O2 during charging [24], a pivotal mechanistic revelation that catalyzed the rapid development of high‐performance, reversible LOBs. Over the past decade, substantial efforts have been dedicated to enhancing reaction kinetics, mitigating parasitic pathways and improving cycling stability, with notable breakthroughs in cathode catalyst design [25]. Reported catalyst systems include carbon‐based materials, noble‐metal catalysts, transition metal (TM) oxides, and soluble redox mediators (RMs). Yet, each category exhibits inherent limitations [26], carbon materials are prone to parasitic reactions at high potentials; noble metals, despite their superb catalytic activity, suffer from high cost and scarcity; and many TM oxides display limited conductivity and structural instability. Therefore, designing low‐cost, highly active, and structurally tunable cathode catalysts remains a central scientific challenge for the practical realization of LOBs [27]. Among various catalyst candidates, TM oxide, particularly manganese oxide (MnOx), have emerged as highly compelling [28]. MnOx benefit from natural abundance, intrinsically favorable oxygen evolution reaction/oxygen reduction reaction (OER/ORR) activity, and diverse oxidation states and polymorphic structures. Distinct MnO2 polymorphs (α, β, γ, δ, λ, etc.) offer various tunnel and layered frameworks that facilitate the transport and transformation of O2, Li+, and LixOy intermediates [29]. Moreover, the redox flexibility of Mn enables activity enhancement through defect engineering, heteroatom modulation, and rational exposure of specific crystal facets [30]. Previous studies have demonstrated that constructing hierarchical porous structures, tailoring surface active sites, and optimizing interfacial reaction pathways can substantially improve the reversible formation/decomposition of Li2O2 [31]. These modifications suppress side reactions, enhance discharge capacity, reduce overpotential, and improve cycling stability. Against this backdrop, this review systematically examines recent advances in the structural design and performance modulation of MnOx‐based cathode catalysts for LOBs. Emphasis is placed on pore‐architecture engineering, active‐site regulation, crystal‐phase and defect manipulation, and multi‐component synergistic strategies. Furthermore, we discuss the mechanistic roles of Mn‐based catalysts in facilitating the reversible formation of Li2O2, aiming to provide new perspectives and theoretical guidance for the development of efficient, low‐cost cathode catalysts for next‐generation LOB systems. Classification, Challenges, and Reaction Mechanisms of LOBs A LOB typically consists of four major components: a porous O2 cathode, a metallic Li anode, an electrolyte, and a waterproof‐breathable membrane (the latter can be omitted under a dry O2 atmosphere). According to the type and physical state of the electrolyte layer, LOBs can be categorized into four configurations (Figure 1a–d) [32, 34]: non‐aqueous systems [35], aqueous systems [36], solid‐state systems [37], and hybrid aqueous/non‐aqueous systems [38]. (a–d) Schematic diagrams of LOBs with different electrolytes: non‐aqueous (a), aqueous (b), solid‐state (c), and hybrid (d). Reproduced with permission [32]. Copyright 2019, Wiley. e) Schematic diagram of LOB configuration and practical problems in cathode materials. Reproduced with permission [33]. Copyright 2020, Elsevier. The charge/discharge process proceeds as follows: during discharge, O2 from the environment diffuses into the porous cathode and is activated and reduced on the catalytic surface. Meanwhile, Li metal at the anode is oxidized to Li+, which migrates through the electrolyte [39]. At the gas‐liquid‐solid three‐phase interface, comprising O2, electrolyte, and the catalyst surface, Li+ reacts with reduced O species to form solid discharge products that are insoluble and electronically insulating in organic electrolytes [40]. During charging, these solid products are oxidatively decomposed under the catalysis of the cathode material, regenerating Li+ and releasing O2. Thus, the entire electrochemical process occurs at the cathode side, with Li+ shuttling through the electrolyte to reach the reaction sites. The electrochemical reaction mechanisms of the various LOB configurations are summarized in Table 1. In aqueous systems, direct contact between metallic Li and the aqueous electrolyte leads to spontaneous reduction reactions, posing severe safety hazards [41]. In hybrid aqueous/non‐aqueous systems, an organic electrolyte is employed on the Li side while an aqueous electrolyte is used at the O2 electrode. A solid electrolyte layer (Li+ conducting ceramic membrane) is inserted between them to block direct contact while enabling Li+ transport. This design protects the Li metal and mitigates the continuous accumulation of solid Li2O2 on the O2 electrode. However, the solid electrolyte layer is chemically unstable in strongly acidic or alkaline environments, and significant differences in Li+ diffusion kinetics across multiple electrolyte phases further limit practical performance. TABLE 1Electrochemical reaction mechanisms in LOBs with different electrolytes.ReactionNon‐aqueous systemAqueous and hybrid systemsSolid‐state systemCathode reactionO2 + 2Li+ + 2e− → Li2O2 O2 + 2H2O + 4e− → 4OH− (Alkaline) O2 + 4e− + 4H+ → 2H2O (Acidic) O2 + 2Li+ + 2e− → Li2O2 Anode reactionLi → Li+ + e− Overall reaction 2Li + O2 → Li2O2 (E 0 = 2.96 V vs. Li/Li+) O2 + 2H2O + 4Li ↔ 4Li+ + 4OH− (E 0 = 3.43 V vs. Li/Li+, Alkaline) O2 + 4H+ + 4Li ↔ 4Li+ + 2H2O (E 0 = 4.26 V vs. Li/Li+, Acidic) 2Li + O2 → Li2O2 (E 0 = 2.96 V vs. Li/Li+) Electrochemical reaction mechanisms in LOBs with different electrolytes. O2 + 2H2O + 4e− → 4OH− (Alkaline) O2 + 4e− + 4H+ → 2H2O (Acidic) 2Li + O2 → Li2O2 (E 0 = 2.96 V vs. Li/Li+) O2 + 2H2O + 4Li ↔ 4Li+ + 4OH− (E 0 = 3.43 V vs. Li/Li+, Alkaline) O2 + 4H+ + 4Li ↔ 4Li+ + 2H2O (E 0 = 4.26 V vs. Li/Li+, Acidic) 2Li + O2 → Li2O2 (E 0 = 2.96 V vs. Li/Li+) Solid‐state LOBs alleviate issues such as Li corrosion and electrolyte decomposition, but their solid electrolytes typically suffer from low ionic conductivity. Consequently, their discharge capacities and cycle life are generally inferior to those of liquid‐electrolyte systems [42]. For these reasons, current research efforts predominantly focus on non‐aqueous LOBs employing proton‐inert organic electrolytes, which exhibit superior reversibility and cycling stability. The present work is also conducted within the framework of this non‐aqueous LOB system. In non‐aqueous LOBs, the cell operates as an open system. During discharge, metallic Li at the anode is oxidized to Li+, which migrates through the electrolyte toward the O2 cathode. Simultaneously, molecular O2 from the surrounding environment diffuses into the porous cathode and, under the catalytic action of the electrode materials, is reduced to O2 −. At the gas‐liquid‐solid three‐phase interface, comprising O2, the electrolyte, and the cathode surface, the reduced O species subsequently react with Li+ to form the discharge products. The overall reaction pathway is generally expressed as: O2 + e− → O2 − and Li+ + O2 → LiO2, indicating that the ORR occurs first at the cathode side. Because LiO2 is thermodynamically unstable, the solid discharge product Li2O2 typically forms through two concurrent pathways: a disproportionation reaction and an electrochemical reduction process [33]. Both routes ultimately yield the same overall transformation: 2LiO2 → Li2O2 + O2 and LiO2 + Li+ + e− → Li2O2. During charging, the discharge product Li2O2 is decomposed under the applied potential and the catalytic action of the electrode materials, generating Li+ while releasing O2, as summarized in Table 1 [43]. However, because Li2O2 is an insoluble and electronically insulating solid in non‐aqueous electrolytes, its continuous accumulation progressively blocks the pores of the O2 electrode and covers the catalytic active sites, resulting in rapid deterioration of electrochemical performance. In addition, highly reactive intermediates formed during discharge, such as LiO2 and Li2O2, can attack the electrolyte and react with carbon materials, leading to severe parasitic reactions. Consequently, the practical application of non‐aqueous LOBs remains challenging. The key issues can be summarized as follows: Large charge/discharge overpotentials and low energy efficiency [20]. Although the equilibrium potential of a LOB is 2.96 V, the practical charge/discharge voltage gap is typically very large, resulting in energy efficiency far below the ∼90% required for commercial use. This problem primarily originates from the insulating nature of Li2O2, which is neither soluble nor conductive in non‐aqueous electrolytes. As discharge proceeds, Li2O2 accumulates within the cathode pores, blocking transport pathways and passivating catalytic sites, thereby slowing reaction kinetics. The intrinsic room‐temperature conductivity of Li2O2 is only 10−9‐10−12 S cm−1, severely limiting charge transport and causing the operating potentials to deviate significantly from the equilibrium value. Therefore, developing porous, highly active bifunctional catalysts or introducing suitable soluble RMs is essential for improving energy efficiency. Large charge/discharge overpotentials and low energy efficiency [20]. Although the equilibrium potential of a LOB is 2.96 V, the practical charge/discharge voltage gap is typically very large, resulting in energy efficiency far below the ∼90% required for commercial use. This problem primarily originates from the insulating nature of Li2O2, which is neither soluble nor conductive in non‐aqueous electrolytes. As discharge proceeds, Li2O2 accumulates within the cathode pores, blocking transport pathways and passivating catalytic sites, thereby slowing reaction kinetics. The intrinsic room‐temperature conductivity of Li2O2 is only 10−9‐10−12 S cm−1, severely limiting charge transport and causing the operating potentials to deviate significantly from the equilibrium value. Therefore, developing porous, highly active bifunctional catalysts or introducing suitable soluble RMs is essential for improving energy efficiency. Poor rate capability. The LOB relies on gas‐solid interfacial reactions involving a two‐phase ORR/OER process, which is intrinsically slower than gas‐liquid or homogeneous reactions. Under high current densities, Li2O2 forms rapidly, leading to rapid catalyst passivation and an increase in electrode resistance, which accelerates performance decay and prevents high‐rate operation [44]. To overcome this limitation, catalysts that promote the solution‐mediated formation of Li2O2 or guide its controlled solid‐state growth are needed to avoid sluggish two‐phase conversion. Furthermore, optimizing the porosity and electronic conductivity of the O2 electrode can significantly enhance rate performance. Poor rate capability. The LOB relies on gas‐solid interfacial reactions involving a two‐phase ORR/OER process, which is intrinsically slower than gas‐liquid or homogeneous reactions. Under high current densities, Li2O2 forms rapidly, leading to rapid catalyst passivation and an increase in electrode resistance, which accelerates performance decay and prevents high‐rate operation [44]. To overcome this limitation, catalysts that promote the solution‐mediated formation of Li2O2 or guide its controlled solid‐state growth are needed to avoid sluggish two‐phase conversion. Furthermore, optimizing the porosity and electronic conductivity of the O2 electrode can significantly enhance rate performance. Short cycling life. Reactive ORR intermediates attack carbon cathodes and non‐aqueous electrolytes, causing structural degradation and electrolyte decomposition. This leads to the formation of high‐voltage parasitic products such as Li2CO3, which severely shorten cycling life [45]. Additionally, incomplete decomposition of Li2O2 due to limited catalytic activity results in its gradual accumulation, blocking active sites and pores. Over cycling, the charging voltage progressively increases, and excessively high charging potentials further destabilize carbon cathodes and electrolytes, triggering a detrimental self‐accelerating degradation loop. The development of more electrochemically stable electrolytes or non‐carbon cathode catalysts is therefore crucial for achieving long‐life LOBs. Short cycling life. Reactive ORR intermediates attack carbon cathodes and non‐aqueous electrolytes, causing structural degradation and electrolyte decomposition. This leads to the formation of high‐voltage parasitic products such as Li2CO3, which severely shorten cycling life [45]. Additionally, incomplete decomposition of Li2O2 due to limited catalytic activity results in its gradual accumulation, blocking active sites and pores. Over cycling, the charging voltage progressively increases, and excessively high charging potentials further destabilize carbon cathodes and electrolytes, triggering a detrimental self‐accelerating degradation loop. The development of more electrochemically stable electrolytes or non‐carbon cathode catalysts is therefore crucial for achieving long‐life LOBs. Safety concerns associated with the Li metal anode. As an open system, the LOB exposes highly reactive metallic Li to external gases and impurities, making parasitic reactions unavoidable. Moreover, uncontrolled Li deposition leads to dendrite formation, which can pierce the separator and cause short circuits or even fires. Repeated Li plating/stripping induces substantial volume fluctuations, destabilizing the solid electrolyte interphase and resulting in continuous consumption of both Li and electrolyte [46, 47], as well as increased polarization. Thus, implementing effective strategies to protect the Li metal anode is essential for improving the safety and stability of LOBs. Safety concerns associated with the Li metal anode. As an open system, the LOB exposes highly reactive metallic Li to external gases and impurities, making parasitic reactions unavoidable. Moreover, uncontrolled Li deposition leads to dendrite formation, which can pierce the separator and cause short circuits or even fires. Repeated Li plating/stripping induces substantial volume fluctuations, destabilizing the solid electrolyte interphase and resulting in continuous consumption of both Li and electrolyte [46, 47], as well as increased polarization. Thus, implementing effective strategies to protect the Li metal anode is essential for improving the safety and stability of LOBs. Recent Advances in Cathode Catalyst Materials for LOBs The surface of the O2 cathode, where the redox reactions occur, plays a decisive role in governing the overall performance of LOBs (Figure 1e) [33]. According to the reaction mechanisms and the physicochemical characteristics of the discharge products, a high degree of porosity and abundant catalytically active surface sites are widely recognized as essential attributes for effective cathode materials. Guided by these design principles, significant progress has been made in recent years toward developing high‐efficiency cathode catalysts that exhibit improved reaction kinetics and reversibility for LOBs [48]. Cathode catalysts reported to date can be broadly categorized into four major classes: carbon‐based materials, noble‐metal‐based catalysts, TM‐based oxides and compounds, and soluble catalyst systems. Each category offers distinct structural and catalytic advantages, while also presenting unique challenges that continue to shape ongoing research efforts. Despite the attractive properties of non‐TM catalyst systems, including carbon materials and soluble catalysts, their intrinsic limitations remain significant in non‐aqueous LOBs. Carbon‐based materials primarily act as conductive frameworks rather than intrinsically active catalytic centers, and their catalytic activity strongly depends on defect sites and heteroatom functionalization. More importantly, carbon surfaces are susceptible to parasitic reactions with reactive oxygen species and Li2O2, particularly at elevated charging potentials, resulting in irreversible products such as Li2CO3 and severe electrode degradation [49]. Soluble RMs, although capable of regulating Li2O2 formation/decomposition through solution‐mediated pathways, often suffer from shuttle effects, mediator degradation, and complex side reactions with electrolytes and Li metal. In contrast, TM‐based catalysts provide tunable electronic structures through variable d‐orbital occupations, allowing stronger control over oxygen adsorption/desorption and reaction intermediates. Therefore, the development of TM‐based catalysts with optimized electronic structures remains a key strategy for achieving efficient bifunctional ORR/OER activity in LOB systems. Carbon‐Based Catalyst Materials Carbon materials have been extensively employed in LOBs owing to their high electrical conductivity, low cost [50, 51], and the ease with which 3D porous architectures can be constructed (Figure 2). In addition to commercial conductive carbons such as Super P [52], Ketjen Black (KB) [53], Vulcan carbon [54], and acetylene black [55], a variety of functional carbon materials with unique microstructures, including 1D carbon nanotubes (CNTs), 2D graphene [56, 57], and 3D porous carbon nanostructures [58, 59], have demonstrated promising potentials [60]. Various types of cathode catalyst materials for LOBs. Reproduced with permission [67]. Copyright 2013, Royal Society of Chemistry. Reproduced with permission [68]. Copyright 2021, Elsevier. Reproduced with permission [69]. Copyright 2014, American Chemical Society. Vertically aligned CNT arrays fabricated through chemical vapor deposition possess a highly ordered structure that promotes efficient O2 diffusion within the cathode while simultaneously exposing abundant active sites for redox reactions [61]. Such an architecture facilitates mass transport and interfacial charge transfer processes, leading to improved reaction kinetics and enhanced cycling stability in LOBs. In addition, porous CNT electrodes prepared at different synthesis temperatures exhibited significant differences in electrochemical behavior, with optimized structures delivering remarkable discharge capacities [62]. Variations in graphitization degree and the abundance of O‐containing functional groups on the carbon surface were found to strongly influence the electrochemical response of the electrodes by affecting conductivity and surface reaction characteristics. N‐doped 3D graphene aerogels synthesized through a hydrothermal strategy feature a hierarchical macroporous–mesoporous framework that effectively facilitates O2 diffusion, promotes complete electrolyte infiltration, and accommodates the deposition of solid discharge products within the cathode structure [63]. The interconnected porous network alleviates mass transport limitations and provides sufficient reaction space, enabling a high specific capacity of approximately 7300 mAh g−1 while maintaining around 4000 mAh g−1 even at a current density of 200 mA g−1. Structural regulation through templating strategies has also been employed to optimize pore architectures. Microporous graphene papers and porous CNT membranes prepared using polystyrene colloidal spheres as sacrificial templates exhibited enlarged pore channels that allowed the reversible formation and decomposition of Li2O2 within the cathode framework [64]. In parallel with pore‐structure engineering, heteroatom doping, such as N, P, B, and S incorporation, has been explored as an effective approach for modifying the electronic structure and surface chemistry of carbon materials [65]. However, carbon materials are prone to instability during electrochemical cycling, which negatively affects long‐term durability. Bruce et al. employed differential electrochemical mass spectrometry and infrared spectroscopy to analyze cycled electrodes and gaseous products [66]. They reported that carbon materials remain stable below 3.5 V. However, above this threshold, carbon not only reacts with Li2O2 to form parasitic products such as Li2CO3 but may also undergo direct decomposition. Noble‐Metal‐Based Catalyst Materials Noble metals possess partially filled d orbitals, high electrochemical stability, and moderate adsorption strengths toward reaction intermediates, enabling significant enhancement of the reaction kinetics of the OER/ORR. Noble metals and their compounds, including Pt, Pd, Au, Ru, and Ir, have demonstrated exceptional catalytic performance in LOBs (Figure 2) [70, 71, 72, 73, 74, 75]. The use of dimethyl sulfoxide electrolytes combined with porous gold cathodes has demonstrated that optimizing both the reaction medium and cathode architecture can effectively improve the electrochemical behavior of LOBs [76]. The porous metallic framework facilitates reactant transport and interfacial reactions, allowing the system to maintain 95% capacity retention and stable cycling over 100 cycles even under high current densities. Further enhancement of cathode structures through integrated electrode design has been achieved by constructing interconnected porous Pd networks [77]. The continuous porous framework improves electron transport and provides accessible reaction pathways, leading to a cycling life exceeding 200 cycles under a fixed cutoff capacity. Hierarchical catalyst configurations integrating conductive frameworks and active catalytic sites have also been explored to regulate reaction kinetics and discharge‐product deposition behavior. N‐doped hollow carbon spheres loaded with Ir nanoparticles employed mesoporous ultrathin shells to accelerate mass transport, while the hollow interior created sufficient space for accommodating solid Li2O2 deposition [78]. Uniformly distributed Ir nanoparticles provided highly exposed catalytic surfaces that promoted electrochemical reactions and reduced charging overpotential. Amorphous RuO2 catalysts prepared through hydrothermal approaches further highlight the role of structural disorder in catalytic regulation. The presence of abundant defects, vacancies, and intrinsically disordered domains strengthened the adsorption of O2 − and LiO2 intermediates, enabling modulation of the particle size, morphology, crystallinity, and distribution of Li2O2 [68]. Despite their outstanding catalytic properties, the scarcity and high cost of noble metals hinder their large‐scale deployment. Therefore, strategies that maximize catalytic utilization and minimize the required loading of rare metals such as Pt and Ir will ultimately determine the industrial feasibility of noble‐metal‐based catalysts in LOBs. Soluble Catalysts (RMs) In non‐aqueous LOBs, the discharge products are insoluble and electronically insulating in organic electrolytes, often leading to unstable interfacial contact and severe blockage of the cathode pores. As a result, systems employing solely solid‐state catalysts still suffer from sluggish reaction kinetics and poor rate capability. By contrast, soluble catalysts, also referred to as RMs, exhibit favorable mobility within the electrolyte, enabling homogeneous dispersion and intimate contact with the entire surface of the discharge products. This unique characteristic has attracted considerable attention in recent years (Figure 2) [79]. According to their functional roles in LOBs, RMs can be broadly categorized into two types: ORR‐type RMs and OER‐type RMs. The following sections will discuss each category in detail, highlighting their catalytic mechanisms, representative molecular systems, and corresponding electrochemical benefits. Although RMs are commonly categorized according to their dominant function in either ORR or OER processes, the distinction originates fundamentally from differences in their electronic structures and redox characteristics at the molecular level. ORR‐type RMs generally possess relatively low reduction potentials and electron‐rich states that facilitate electron donation to O2 molecules or LiO2 intermediates, thereby accelerating oxygen activation and promoting solution‐mediated Li2O2 formation [80]. By contrast, OER‐type RMs typically exhibit higher oxidation potentials and more stable oxidized states, enabling them to chemically oxidize Li2O2 during charging. From an electronic‐structure perspective, these behaviors can be interpreted in terms of differences in the density of states (DOS) near the Fermi level. ORR‐type mediators generally exhibit a higher DOS around occupied states that promotes electron transfer toward oxygen species, whereas OER‐type mediators favor accessible unoccupied states capable of accepting electrons from Li2O2 oxidation processes. Therefore, the energy‐level alignment and DOS distribution of redox mediators play critical roles in determining their preferred catalytic functionality. ORR‐Type RMs ORR‐type RMs are typically capable of altering the formation pathway of Li2O2 during discharge. Their ability to enhance the ORR in LOBs generally stems from two primary mechanisms. First, through reversible changes in their oxidation states, RMs can accelerate electron transfer between the cathode surface and molecular O2 during the electrochemical reaction. Second, RMs can react with the LiO2 intermediate to form abundant RM‐LiO2 adducts, thereby inducing the solution‐mediated formation of Li2O2. This process effectively prevents catalyst passivation at the cathode surface and significantly increases the discharge capacity [81]. Lacey et al. first introduced ethyl viologen ditriflate (EtV(oTf)2) as a RM to improve ORR performance in LOBs [82]. During discharge, EtV(oTf)2 facilitates the reduction of O2 and promotes the disproportionation‐driven formation of Li2O2. However, because its redox potential (∼2.4 V vs. Li/Li+) is relatively low, a substantial portion of O2 still undergoes direct electrochemical reduction on the cathode surface, leaving the electrode passivation issue unresolved. 2,5‐di‐tert‐butyl‐1,4‐benzoquinone (DBBQ) was later introduced as a RM in low‐polarity and weakly solvating electrolytes [83]. Compared with earlier systems, DBBQ more effectively redirects the ORR pathway toward solution‐mediated processes, thereby suppressing direct Li2O2 accumulation on the cathode surface. Experimental results demonstrated substantially reduced discharge overpotentials together with an 80–100‐fold increase in discharge capacity. More recent investigations have further indicated that trace amounts of water in the electrolyte can strengthen the solution‐mediated pathway, accompanied by a morphological transition of Li2O2 from toroidal particles to plate‐like structures, which contributes to lower overpotentials (Figure 2). However, excess water reacts with Li metal to form parasitic products and introduces severe safety concerns [84, 85]. Beyond these examples, several other species, including tris(2,4,6‐trichlorophenyl)methyl radicals [86], coenzyme Q10 [87], and inorganic polyoxometalates [88], have also been identified as effective ORR‐type RMs capable of enhancing the electrochemical performance of LOBs. OER‐Type RMs OER‐type RMs typically promote the decomposition of Li2O2 through a chemical oxidation pathway. In this process, the mediator is first electrochemically oxidized at the cathode surface to form RM+, which subsequently oxidizes Li2O2 chemically, generating Li+ and releasing O2 [89]. A wide variety of OER‐type RMs have been reported, falling broadly into three categories: organic molecules, organometallic salts, and inorganic compounds. In 2013, Bruce and co‐workers first introduced tetrathiafulvalene [90], an organic redox‐active molecule, as an OER‐type RM for LOBs, achieving a substantial improvement in cycling stability. Bergner et al. demonstrated that 2,2,6,6‐tetramethylpiperidinyl‐1‐oxyl possesses high electrochemical stability [69], fast diffusion kinetics, and an appropriate redox potential, enabling it to markedly lower the charging overpotential to 3.5–3.7 V. Whan Shin and colleagues functionalized phenothiazine with ammonium‐based ionic liquid groups [91], creating a mediator capable of avoiding undesired reactions with Li metal while significantly improving cycling performance. In addition, halide‐based RMs containing ions such as I− and Br−, including LiI and LiBr, have been shown to participate in Li2O2 decomposition through reversible changes in the oxidation state of the halide species [92, 93]. This catalytic mechanism effectively accelerates the charging reaction and substantially reduces the charging overpotential, providing a promising approach for enhancing the reversibility of LOBs. Although the introduction of soluble RMs has opened new avenues for improving the electrochemical performance of LOBs, their practical application remains constrained by several inherent challenges. In non‐aqueous electrolytes, soluble RMs inevitably undergo a “shuttle effect” [94], which complicates the reaction environment and introduces additional side processes. The involvement of RMs in multiple intertwined electrochemical and chemical pathways makes the overall reaction mechanism difficult to elucidate. Moreover, the shuttle effect can induce corrosion of the Li metal anode and lead to the continuous consumption of RM's own redox‐active sites [95], thereby diminishing their long‐term effectiveness. For these reasons, further investigation is required to understand, control, and ultimately mitigate the limitations associated with soluble RMs. Continued research into their reaction mechanisms, stability, and interactions with electrode/electrolyte components will be essential for enabling their practical deployment in high‐performance LOBs. TM‐Based Catalyst Materials Driven by cost considerations, researchers have increasingly turned to TMs and their oxides, carbides, and nitrides as alternative catalyst materials. Reported TM‐based catalysts primarily include Mn‐based materials, Co‐based materials, spinel‐type oxides, and perovskite structures. Owing to their abundant unstable electronic orbitals and unpaired electrons, these materials typically exhibit intrinsic catalytic activity toward the reactions involved in LOBs [96, 97, 98, 99]. Beyond their compositional diversity, the catalytic performance of TM‐based materials is fundamentally governed by their electronic configurations at the atomic scale. In bifunctional catalysts for LOBs, the adsorption and conversion of oxygen intermediates (O2−, LiO2, and Li2O2) strongly depend on the occupancy and energy distribution of TM d orbitals [100]. Excessively weak adsorption leads to insufficient activation of O2 during ORR, whereas overly strong adsorption hampers the decomposition of Li2O2 during OER. Therefore, highly efficient bifunctional catalysts generally require a moderate electronic configuration capable of balancing adsorption and desorption energies. Previous studies suggest that optimized eg orbital occupancy close to unity and a suitable d‐band center position can facilitate intermediate binding while minimizing reaction barriers. Such electronic‐structure regulation provides an important design principle for developing highly active bifunctional catalysts in LOB systems. The construction of rational catalyst architectures has been widely explored to improve the electrochemical performance of LOBs by increasing active‐site exposure and facilitating reactant transport. In this context, 3D hollow α‐MnO2 frameworks with porous shells were synthesized through a sacrificial‐template strategy and employed as cathode catalysts [96, 101]. The hollow and porous structural characteristics are beneficial for electrolyte penetration and oxygen diffusion while providing sufficient space for discharge‐product accommodation. As a result, the corresponding cells delivered a high specific capacity of 8583 mAh g−1 at 100 mA g−1 and retained 6311 mAh g−1 at 300 mA g−1, together with stable cycling for 170 cycles at 200 mA g−1. Morphology engineering has also been shown to influence catalytic activity and transport behavior significantly. Sea‐urchin‐like NiO‐NiCo2O4 microspheres prepared through a hydrothermal route exhibited a hierarchical structure capable of improving ion and oxygen accessibility [102]. The assembled battery achieved a discharge capacity of 9231 mAh g−1 at 100 mA g−1 and maintained 3711 mAh g−1 at 500 mA g−1, indicating favorable rate capability. Under a current density of 100 mA g−1 with a limited capacity of 600 mAh g−1, stable cycling was maintained for 80 cycles. Beyond structural optimization of metal oxides, integrating catalytic materials with conductive carbon frameworks provides an effective approach for improving charge transport and electrode stability. A binder‐free and self‐supporting air electrode based on 1T‐MoS2 and functionalized CNTs was fabricated via an in‐situ liquid‐phase redox intercalation and exfoliation process [103]. The conductive network formed by CNTs, together with the catalytic contribution of 1T‐MoS2, enabled stable battery operation for 100 cycles at 200 mA g−1 with a cutoff capacity of 500 mAh g−1. Further enhancement in catalytic performance has been achieved through the synergistic combination of active nanoparticles and heteroatom‐doped carbon substrates. Uniform anchoring of CoO‐Co3O4 nanoparticles onto N‐doped hollow carbon spheres generated a catalyst structure with abundant exposed active sites and a large accessible surface area [104]. Benefiting from these structural characteristics, the battery delivered an ultrahigh discharge capacity of 24265 mAh g−1 at 300 mA g−1, while cells employing the N‐HC@CoO‐Co3O4 cathode maintained stable cycling for more than 112 cycles at a cutoff capacity of 500 mAh g−1. Critical Considerations in Performance Evaluation Although numerous studies have reported significant improvements in discharge capacity, cycling life, and rate performance of LOBs, direct comparison among different catalyst systems remains challenging because electrochemical performance is highly dependent on testing conditions [105, 106]. Parameters including electrolyte composition, O2 purity, current density, electrode loading, cathode architecture, and capacity limitations can strongly influence reported results. In many cases, exceptionally high discharge capacities are obtained under very low current densities or low cathode mass loadings, which may not represent realistic operating conditions. Since capacity values are frequently normalized to catalyst or electrode mass, low loading levels can artificially produce very high specific capacities while contributing little to practical energy density at the device level. Furthermore, long cycling stability is often evaluated using capacity‐limited cycling protocols [107]. Under such conditions, the discharge process is intentionally terminated before substantial accumulation of Li2O2 occurs, thereby reducing electrode passivation and mitigating degradation processes. While this approach provides useful information regarding catalyst reversibility, it may significantly overestimate long‐term cycling stability under practical operating conditions. Therefore, it is important to distinguish between metrics suitable for academic benchmarking and those relevant to practical implementation [108]. Academic studies often prioritize understanding reaction mechanisms and evaluating intrinsic catalytic activity under controlled conditions. By contrast, practical LOB systems require simultaneous consideration of factors including areal capacity, electrode loading, energy efficiency, long‐term stability, and realistic operating environments. Consequently, future studies would benefit from more standardized testing protocols and reporting criteria, enabling fair comparison among catalyst systems and facilitating translation from laboratory‐scale demonstrations toward practical LOB devices. MnOx‐Based Catalysts and Their Applications in LOBs Mn element, a first‐row TM with five unpaired electrons, possesses a distinct electronic configuration [109, 110], which endows it with high redox activity. This enables Mn to form a wide range of MnOx, including MnO, MnO2, Mn2O3, Mn3O4, Mn2O5, MnO3, and Mn2O7. In addition, the diverse connection modes of the fundamental [MnO6] octahedral units give rise to a rich variety of MnO2 crystal structures [111, 112], commonly classified into six major polymorphs: α, β, δ, λ, γ, and ε [99]. Mn is also abundant in the Earth's crust, ranking 12th among crustal elements with an approximate content of 0.1%. Compared with many other TM oxides, MnOx are considerably more cost‐effective. The wide range of accessible oxidation states and polymorphic structures provides MnOx‐based materials with exceptional synthetic versatility and tunable physicochemical properties, making them highly attractive as catalysts for LOBs. Owing to the favorable properties of MnOx, considerable progress has been achieved in recent years in the development of MnOx‐based catalysts for LOBs. Table 2 summarizes the representative electrochemical performance of MnOx‐based LOB cathodes reported over the past three years (capacities normalized to catalyst mass). TABLE 2Statistics of the representative performance of MnOx‐based cathodes over the past three years.Cathode MaterialYearCurrent Density (mA g−1)Capacity of Catalyst Materials (mAh g−1)Retention (cycles)Refs.Ru‐doped β‐MnO2 20251000930054.2%/720 h[113]In2S3/MnO2/BiOCl202510019330∼100/1500 h[114]Carbon/RuO2/MnO2 20250.1 mA cm−2 5.24 mAh cm−2 –/730 h[115]Ru@MnCo2O4/Carbon202420027810∼100%/106[116]Mn3O4@CNT202420016895∼100%/97[117]MnCo1.75Cu0.25O4 202417511272–/1250 h[118]MnTe/MnO202420011930–/350[119]0.5La0.6Sr0.4MnO3‐0.5LaMn0.6Co0.4O3 202430014499∼100%/258[120]Ru@La(Mn0.2Co0.2Fe0.2Ni0.2Cr0.2)O3 20245012275∼100%/345[121](La0.8Sr0.2)(Mn0.2Fe0.2Cr0.2Co0.2Ni0.2)O3 202410017078–/435[122]Co‐doped MnCr2O4 202320013600∼100%/150[123]Cr‐doped Mn3O4 202310022288∼100%/74[124]Mn2O3 202350021070∼100%/180[125]FeMnO3@ZrO2 20235011800∼100%/100[126]ε‐MnO2 2023200198248.1%/100[30]MnO2‐Co3O4@CC20231008115–/125[127]Mn2O3@CeO2 2023100012545–/300[128]Co2.85Mn0.15O4 202310005598∼100%/100[129]Ru@MnO2 20230.05 mA cm−2 7.74 mAh cm−2 ∼100%/1800 h[130] Statistics of the representative performance of MnOx‐based cathodes over the past three years. In the following sections, we discuss the application of MnOx‐based catalysts in LOBs from three perspectives: monometallic MnOx, bimetallic MnOx, and multimetallic MnOx. Each category offers distinct advantages in catalytic activity, structural engineering, and reaction‐pathway regulation, enabling tailored optimization of LOB performance. Monometallic MnOx as Catalysts for LOBs Since the Bruce group first demonstrated in 2006 that MnO2 can serve as an effective catalyst in LOBs, thereby achieving promising electrochemical performance, extensive research efforts have been devoted to exploring MnOx materials [133, 134]. Among the various MnOx, MnO2 exhibits the richest polymorphism and can be categorized into three major structural families: 1D tunnel structures (α, β, γ, and ε phases), 2D layered structures (δ phase), and 3D framework structures (spinel‐type λ phase) (Figure 3a–f) [131]. Crystal structures and catalytic behavior of representative MnOx catalysts for LOBs. (a‐f) Schematic diagrams for crystal structures of MnO2: α‐MnO2 (a), β‐MnO2 (b), γ‐MnO2 (c), ε‐MnO2 (d), δ‐MnO2 (e), and λ‐MnO2 (f). Reproduced with permission [131]. Copyright 2018, Wiley. (g) Schematic illustration of the fabrication process of RuO2/Mn2O3 tubular catalysts. (h‐i) Schematic representation of the reversible formation and decomposition processes of Li2O2 during discharge and charge, respectively. Reproduced with permission [132]. Copyright 2016, American Chemical Society. α‐MnO2 contains a 2 × 2 tunnel with a diameter of approximately 0.46 nm, providing ample space for the reversible formation and decomposition of LixOy during cycling, as well as facilitating rapid diffusion of O2, LixOy intermediates, and Li+ [135]. The catalytic activity of MnO2 polymorphs is generally ranked as α‐MnO2 > amorphous MnO2 > β‐MnO2 > δ‐MnO2 [136]. These findings highlight that the crystal structure of MnO2 critically influences both its catalytic activity and the reaction pathways of the ORR/OER processes in LOBs. In addition to crystal structure, the nanoscale dimensions and morphological features of MnOx also play a decisive role in determining their electrocatalytic behavior. For example, the Bruce group reported that nanorod‐shaped α‐MnO2 exhibits an initial discharge capacity of approximately 3000 mAh g−1 [137]. significantly outperforming bulk α‐MnO2, while also offering improved cycling stability. Suib and co‐workers compared the catalytic activities of α‐MnO2 with different morphologies in both aqueous and non‐aqueous electrolytes [138]. Among all the samples studied, solvent‐free synthesized nanorods displayed the highest ORR activity, attributed to their lower average Mn oxidation state, smaller crystallite size, larger surface area, and higher pore volume, as confirmed by limiting and exchange current densities. To improve catalytic activity and mass transport behavior simultaneously, a 3D δ‐MnO2 aerogel was constructed through a combined wet‐chemical synthesis and liquid N2 freeze‐drying process [139]. The interconnected porous framework and high specific surface area provided abundant exposed catalytic sites while promoting effective diffusion of oxygen and electrolyte throughout the electrode structure. These structural features contributed to enhanced reaction kinetics and resulted in excellent electrocatalytic performance during LOB operation. Although MnO2 has repeatedly been demonstrated as an efficient catalyst for LOBs, theoretical calculations suggest that it may react with discharge products to form MnO2‐LixOy intermediates, which could lead to structural instability during cycling [135]. Consequently, MnOx with lower average oxidation states, such as MnO, Mn2O3, and Mn3O4, have attracted increasing attention due to their greater structural stability and promising catalytic properties. The integration of Mn‐based oxides with conductive carbon frameworks has been widely explored to simultaneously improve catalytic activity and charge transport properties. A MnO@CNT composite was synthesized through direct reaction between CNTs and KMnO4 followed by thermal reduction treatment [140]. The conductive CNT network provided efficient electron pathways, while the intrinsic stability and catalytic activity of MnO facilitated the electrochemical reactions involved in LOB operation. Under a current density of 0.4 mA cm−2 and a limited capacity of 1000 mAh g−1, the assembled cell maintained a discharge plateau above 2.4 V after 100 cycles. In addition to MnO, Mn2O3 and Mn3O4, as monometallic MnOx with mixed valence states, have also attracted considerable interest. The coexistence of redox‐active metal ion pairs and lattice distortions associated with multivalent Mn species can generate additional active sites and alter the electronic structure, thereby enhancing electrocatalytic activity [141]. Further enhancement in catalytic performance can be achieved through the synergistic integration of multiple active components and tailored structural design. A RuO2/Mn2O3 bifunctional catalyst with a unique tubular architecture was fabricated using a simple electrospinning technique combined with controlled‐rate calcination (Figure 3g–i) [132]. The tubular morphology can facilitate reactant transport and provide greater accessibility to catalytic sites, while the combination of RuO2 and Mn2O3 enables cooperative catalytic effects during electrochemical reactions. Electrochemical analyses demonstrated that the RuO2/Mn2O3 catalyst exhibited higher OER activity than commercial Pt/C in alkaline media, and LOBs employing this catalyst maintained stable cycling over 100 cycles. The coupling of catalytic nanoparticles with conductive carbon frameworks has also been utilized to improve electron transport and catalyst utilization. Carbon nanofibers (CNFs) modified with Mn3O4 nanoparticles (Mn3O4/CNFs) were developed as catalysts for LOBs operating in a hybrid electrolyte [142]. Compared with electrodes prepared using Mn3O4 mixed with KB or pure KB, the Mn3O4/CNF‐KB composite significantly reduced charge/discharge overpotentials and enhanced cycling stability, which can be attributed to improved electrical conductivity and more effective dispersion of catalytic active sites. Bimetallic MnOx as Catalysts for LOBs To harness the synergistic catalytic effects between different metal ions and further enhance the electronic conductivity of MnOx, extensive research has been devoted to bimetallic oxide systems such as AMn2O4, MnB2O4, ABO4, and AMnO3. MnB2O4 and AMn2O4 oxides adopt spinel and inverse‐spinel structures (Figure 4a,b), in which Mn2+ and Mn3+ occupy tetrahedral and octahedral sites within the crystal lattice. Here, B denotes trivalent metal ions such as Fe, Co, Al, and Cr, whereas A represents divalent TM ions including Fe and Co. (a–c) Crystal structure of spinel‐type MnCo2O4 (a), inverse spinel‐type CoMn2O4 (b), and scheelite‐type MnMoO4 (c). (d) Catalytic mechanism for MnMoO4. (e) Cycle lifespan of MnMoO4 at different current density. Reproduced with permission [144]. Copyright 2017, Wiley. (f) Crystal defects in nonstoichiometric oxides of ABO3. Reproduced with permission [146]. Copyright 2015, American Chemical Society. Structural regulation and compositional engineering of Mn‐based oxides have been extensively explored to optimize catalytic activity and electrochemical behavior in LOBs. Various spinel‐type materials with distinct morphologies, including nanorods, nanotubes, and tube‐in‐tube structures of NiMn2O4, ZnMn2O4, and CoMn2O4, were fabricated through electrospinning followed by controlled‐rate thermal treatment [143]. The structural diversity generated by this approach can influence mass transport pathways and active‐site accessibility. Among these materials, CoMn2O4 nanotubes exhibited superior electrochemical performance, enabling LOBs to deliver a discharge capacity of 5335 mAh g−1 at a current density of 100 mA g−1. Tungsten‐bronze‐type ABO4 oxides have also attracted considerable attention because of their abundant O vacancies. When the concentration of A–O–B bridges becomes sufficiently high, the resulting anion vacancies can introduce intrinsic n‐type conductivity into ABO4 MnOx systems. MnMoO4 nanowires synthesized via co‐precipitation followed by a solid‐state reaction demonstrated that O vacancies generated through dual‐metal‐ion coordination play an important role in regulating electrochemical reversibility in LOBs (Figure 4c–e) [144]. Such defect structures can alter the electronic environment and facilitate charge transfer during electrochemical processes. The corresponding cells exhibited excellent rate capability and maintained stable cycling for 188 cycles at a limited capacity of 1000 mAh g−1. Even under increased current densities and larger capacity cutoffs, stable operation beyond 50 cycles was still maintained. The AMnO3 family belongs to perovskite‐type MnOx materials, in which A represents rare‐earth or alkaline‐earth metal ions. Within this structure, Mn atoms are octahedrally coordinated by six O atoms, forming a framework that can provide flexible electronic regulation and tunable catalytic behavior, with CaMnO3 being one of the most representative examples. Porous mesh‐like CaMnO3 nanoparticles prepared through a sol‐gel process generated a catalyst architecture with a large accessible surface area and interconnected transport pathways [145]. When employed in LOBs, the CaMnO3/C cathode effectively reduced reaction overpotentials and maintained stable cycling for more than 80 cycles. Multimetallic MnOx as Catalysts for LOBs In perovskite‐type oxides (ABO3), partially substituting the A‐ or B‐site atoms with heteroatoms, while preserving the overall crystal structure, can significantly enhance electronic and ionic conductivity, introduce a higher concentration of defects, and improve lattice O mobility (Figure 4f) [146]. Such modifications offer an effective strategy to tune catalytic activity and stability for LOB applications. The first to employ La0.8Sr0.2MnO3 as a catalyst for LOBs was by Débart et al. They investigated its influence on electrochemical performance [147]. Their results demonstrated that La0.8Sr0.2MnO3 serves as an efficient ORR catalyst, delivering a discharge potential of up to 2.6 V. Morphology engineering of perovskite‐type catalysts has been demonstrated to exert a significant influence on electrochemical performance through regulation of active‐site exposure and mass transport behavior. Porous La0.75Sr0.25MnO3 nanotubes (PNT‐LSM) prepared through electrospinning followed by annealing provided an interconnected porous framework capable of facilitating oxygen diffusion and electrolyte penetration [148]. Compared with pristine KB cathodes, the incorporation of PNT‐LSM increased the discharge potential by 30–50 mV and lowered the charging potential by 200 mV at a current density of 0.025 mA cm−2, while delivering a maximum discharge capacity of 11000 mAh g−1. When combined with Super P, the PNT‐LSM cathode further exhibited stable cycling for more than 124 cycles under a limited capacity of 1000 mAh g−1. Beyond morphological optimization, compositional regulation of perovskite structures offers an additional strategy for tuning catalytic properties. Highly active oxidized LaxCa1‐xMnO3 nanoparticles with particle sizes of 20–35 nm were synthesized through an ionic‐liquid‐based approach [149]. Modifying the A‐site composition can induce simultaneous changes in both the geometric and electronic structures of the perovskite lattice, leading to shifts in the average Mn oxidation state and corresponding variations in catalytic activity. Operando Characterization of MnOx‐Based Catalysts in LOBs Recent advances in operando characterization techniques have significantly improved the understanding of dynamic processes occurring in LOB cathodes. Unlike ex situ measurements, operando approaches enable real‐time monitoring of reaction intermediates, discharge‐product evolution, and structural transformations during cycling. Techniques such as operando X‐ray diffraction (XRD), Raman spectroscopy, transmission electron microscopy (TEM), differential electrochemical mass spectrometry (DEMS), and X‐ray absorption spectroscopy (XAS) have been widely employed to probe Li2O2 formation/decomposition and catalyst evolution [150, 151, 152]. These techniques provide direct information regarding phase transitions, reaction pathways, gas evolution, and interfacial processes under practical operating conditions, thereby overcoming the limitations associated with post‐mortem characterization. In particular, they can distinguish between surface‐mediated and solution‐mediated reaction mechanisms and reveal the dynamic behavior of oxygen intermediates during discharge and charge processes. For MnOx‐based catalysts, these techniques are particularly valuable because the catalytic activity strongly depends on the Mn oxidation state [125], crystal phase, and local coordination environment. For example, operando XAS can track variations in Mn valence states and local structural evolution during ORR/OER processes, while operando Raman and XRD can reveal the nucleation and decomposition behavior of Li2O2 and identify parasitic products. Moreover, operando DEMS enables direct detection of O2 consumption and evolution behavior, providing insights into reaction reversibility and side reactions associated with electrolyte decomposition. Advanced operando TEM can further visualize morphology evolution and the growth behavior of discharge products at the nanoscale [153]. Such real‐time observations provide direct evidence for catalyst–intermediate interactions and facilitate the establishment of structure–activity relationships for rational catalyst design. Furthermore, combining operando characterization with theoretical calculations, such as density functional theory, may enable deeper understanding of reaction energetics and dynamic catalytic mechanisms, thereby guiding the development of highly efficient MnOx‐based cathodes for practical LOB applications. Comparison of MnOx with Other Representative Cathode Catalysts Although MnOx‐based catalysts have attracted considerable attention because of their low cost, abundant reserves, and diverse oxidation states, their performance should be evaluated in comparison with other representative catalyst systems employed in LOBs. Noble‐metal‐based catalysts, such as Pt‐, Ru‐, and Ir‐containing materials, generally exhibit superior intrinsic catalytic activity and lower overpotentials owing to their optimized electronic structures and favorable adsorption characteristics toward oxygen intermediates [154, 155, 156]. However, their practical implementation remains limited by high cost and scarcity. Co‐based oxides and spinel structures have also demonstrated excellent bifunctional ORR/OER activity and often deliver higher electronic conductivity than MnOx [157]. Similarly, Mn‐free perovskite catalysts can provide improved oxygen‐ion mobility and tunable electronic structures through A‐ and B‐site engineering. Nevertheless, these materials frequently involve more complex synthesis procedures and higher material costs. In contrast, MnOx‐based catalysts offer distinct advantages arising from their structural diversity, variable oxidation states, and ease of compositional modification [158, 159]. The availability of multiple polymorphs and defect‐engineering strategies enables flexible regulation of catalytic activity and reaction pathways. However, the relatively low intrinsic electronic conductivity of MnOx and its potential structural evolution during cycling remain important limitations. It should also be noted that the superior performance reported for some MnOx systems may not solely originate from the intrinsic catalytic properties of MnOx itself. Factors such as hierarchical electrode architectures, conductive carbon frameworks, heteroatom doping, and optimized testing conditions may contribute substantially to the observed improvements [160, 161, 162]. Therefore, meaningful evaluation of catalyst performance requires simultaneous consideration of catalyst composition, electrode design, and testing protocols. MnOx should not necessarily be regarded as universally superior to competing catalyst systems, but rather as a highly promising and economically attractive platform with considerable potential for further optimization. Electronic‐Structure Regulation and Mechanistic Considerations The catalytic behavior of MnOx in LOBs is fundamentally governed by its electronic structure, which determines the adsorption strength and conversion energetics of oxygen intermediates. Parameters including Mn oxidation state, oxygen vacancies, and metal–oxygen covalency play critical roles in regulating ORR/OER pathways and the reversible formation/decomposition of Li2O2. Mn oxidation states strongly influence the occupation of Mn 3d orbitals and the electronic interaction with oxygen species [121]. Higher Mn valence states generally increase the covalent character of Mn─O bonds and modify the adsorption energies of O2 − and LiO2 intermediates. Moderate adsorption strength is desirable because excessively weak interactions may hinder oxygen activation, whereas overly strong adsorption can impede intermediate desorption and Li2O2 decomposition during charging. Oxygen vacancies are also widely recognized as active sites for enhancing catalytic activity [163]. Their introduction can alter local charge density and electronic distributions, facilitating oxygen adsorption and lowering reaction barriers. In several studies, oxygen‐deficient MnOx has been associated with a transition from surface‐mediated Li2O2 growth toward solution‐mediated pathways because modified adsorption energies may reduce catalyst passivation and promote the growth of larger discharge products. However, the mechanistic understanding remains incomplete. For example, whether oxygen vacancies directly induce solution‐mediated growth or instead alter local electrolyte environments remains under debate. Similarly, the relative contributions of disproportionation reactions and direct electrochemical reduction pathways in Li2O2 formation may vary depending on electrolyte properties, current density, and catalyst surfaces [164, 165]. During OER processes, the onset potential and kinetic behavior are strongly affected by the electronic interaction between Mn sites and oxygen‐containing intermediates. Previous studies suggest that stronger metal–oxygen covalency may facilitate charge transfer and reduce reaction barriers for Li2O2 oxidation [166]. Nevertheless, direct experimental evidence linking electronic descriptors to catalytic activity remains limited, and many current interpretations rely heavily on theoretical calculations and indirect spectroscopic observations. Therefore, although relationships between catalyst electronic structures and catalytic performance have been widely proposed, many mechanistic conclusions remain qualitative or model‐dependent. Future studies integrating operando characterization with theoretical calculations are needed to establish quantitative structure–activity relationships and resolve existing mechanistic debates. Chemical and Electrochemical Stability of MnOx Catalysts Although MnOx‐based catalysts have demonstrated promising catalytic activity and cycling performance in LOBs, their long‐term chemical and electrochemical stability under practical operating conditions remains a critical concern. In many reported systems, improved electrochemical performance does not necessarily imply intrinsic catalyst stability, because the catalyst itself may undergo structural evolution or participate in side reactions during repeated cycling. One important degradation pathway involves Mn dissolution and crystal phase transformation during electrochemical operation [167]. Repeated ORR/OER processes can induce changes in local coordination environments and Mn oxidation states, leading to structural rearrangement of MnOx phases. In particular, high‐valence Mn species may exhibit limited thermodynamic stability and become susceptible to reduction or structural collapse under prolonged cycling conditions [168]. Such phase evolution may alter active‐site distributions and gradually deteriorate catalytic activity. Another possible degradation mechanism involves the formation of Mn–LixOy intermediate species during discharge and charge processes [169]. Previous theoretical studies have suggested that interactions between MnOx surfaces and oxygen‐containing intermediates may lead to the formation of surface‐bound Mn–LixOy species [170]. While these intermediate structures may facilitate adsorption and activation of oxygen species, their excessive accumulation may induce irreversible surface reconstruction or block active catalytic sites. However, the precise role of Mn–LixOy intermediates remains incompletely understood because direct experimental observations remain limited. In addition, MnOx catalysts may participate in parasitic reactions involving electrolytes and carbon supports. Reactive oxygen species generated during ORR/OER processes [171], particularly superoxide intermediates and Li2O2‐related species, can attack both electrolytes and conductive carbon materials. Surface catalytic sites may further accelerate undesirable decomposition reactions under certain conditions [172], leading to the formation of irreversible products such as Li2CO3 and other side products. Such reactions can progressively block cathode pores and increase polarization during cycling. Experimental studies employing operando XAS, Raman spectroscopy, and TEM have provided evidence of structural evolution and dynamic changes in catalyst surfaces during operation [116, 173], while theoretical calculations have suggested that variations in adsorption energies and local electronic structures can strongly affect catalyst stability [174]. Nevertheless, many degradation mechanisms remain difficult to distinguish because multiple processes, including electrolyte decomposition, catalyst reconstruction, and discharge‐product accumulation, often occur simultaneously. Therefore, future studies should place greater emphasis on stability‐oriented catalyst design, including stabilization of Mn oxidation states, suppression of structural reconstruction, and mitigation of catalyst‐induced parasitic reactions. Combining advanced operando characterization techniques with theoretical modeling may further clarify degradation pathways and guide the development of durable MnOx‐based cathodes. Modification Strategies for MnOx‐Based Cathode Catalysts As discussed in the previous section, MnOx have attracted extensive attention due to their low cost and intrinsically high catalytic activity. However, their catalytic efficiency, electronic conductivity, and overall electrochemical stability still fall short of meeting the stringent performance requirements for state‐of‐the‐art cathode catalysts in LOBs [175]. Accordingly, rationally tailoring the spatial architecture and surface physicochemical properties of MnOx‐based catalysts is of great significance for ensuring efficient mass and charge transport, reducing reaction overpotentials, and improving cycling stability during repeated charge/discharge processes. To date, the most widely adopted modification strategies for enhancing the catalytic performance of MnOx‐based cathodes include morphological engineering to construct hierarchical porous architectures, defect engineering to boost catalytic activity, and composite strategies that integrate conductive scaffolds to improve electron transport [176, 177]. Construction of Porous Architectures During discharge in LOBs, Li+, O2, and the electrolyte migrate to the O2 cathode, where they participate in the ORR at the solid‐liquid‐gas three‐phase interface, generating solid Li2O2. Once the pores of the O2 electrode become completely clogged by the discharge product, the reaction immediately terminates [178]. Thus, the designed cathode catalyst must not only provide continuous pathways and abundant active sites for Li+/O2/electrolyte transport and interfacial reactions, but also offer sufficient space to accommodate the insulating Li2O2. Moreover, constructing porous architectures is also essential for maintaining cycling stability. Over short‐term cycling, large surface areas and hierarchical porosity help mitigate catalyst deactivation caused by the accumulation of side products, prevent pore blockage, and ensure that active sites remain accessible, thereby significantly improving reversibility. Porous micro‐/nanotubes, nanoflowers, and various 3D architectures can be constructed through chemical synthesis routes [183, 184], while hard‐template removal strategies have been extensively employed for the fabrication of porous TM oxides and porous carbon materials (Figure 5a) [179, 185, 186]. The introduction of hierarchical porous structures is particularly beneficial for LOBs, as it can increase the accessibility of catalytic sites and provide sufficient space for the accommodation of discharge products. A sisal‐like Co9S8 catalyst developed for LOB applications exhibited an open fibrous architecture capable of promoting O2 diffusion and electrolyte infiltration while improving charge‐transfer kinetics [187]. In addition, the enlarged internal space effectively accommodated solid discharge products, alleviating pore blockage during cycling. Consequently, the assembled battery exhibited a low overpotential of only 0.57 V under a cutoff capacity of 1000 mAh g−1 and maintained stable cycling for approximately 100 cycles at 100 mA g−1. Representative modification strategies for improving MnOx‐based cathode catalysts in LOBs. (a) Porous CoMn2O4 spinel architectures prepared via hard‐template synthesis. Reproduced with permission [179]. Copyright 2024, Elsevier. (b) Schematic illustration showing the synergistic role of oxygen vacancies in regulating catalytic activity. Reproduced with permission [180]. Copyright 2017, American Chemical Society. (c) Morphologies of Ag‐doped α‐MnO2. Reproduced with permission [181]. Copyright 2020, Springer Nature. (d) Schematic diagram for the fabrication process of CMF‐G‐Co/CoO cathodes. Reproduced with permission [182]. Copyright 2016, Wiley. Hard‐template engineering has also been applied to regulate pore structures with greater precision. Ordered mesoporous RuO2 with tunable pore sizes was synthesized using SiO2 spheres as a hard template and employed as a carbon‐free cathode for LOBs [188]. Systematic investigation revealed that both specific surface area and pore size strongly influence discharge capacity and round‐trip efficiency. Excessively small pores tend to become blocked rapidly by discharge products and restrict Li+/O2 transport, leading to reduced capacity and increased overpotential. In contrast, excessively large pores can weaken the structural integrity of mesoporous RuO2, resulting in accelerated capacity degradation during repeated cycling. Defect‐Engineering Strategies Studies have shown that introducing defect‐engineering strategies to modify the surfaces of metal‐based catalysts can substantially reduce reaction overpotentials and enhance cycling stability in LOBs [189, 190, 191, 192]. Crystal defects in solid materials are generally categorized as point defects (0D), line defects (1D), planar defects (2D), and bulk defects (3D) [193, 194, 195, 196, 197]. Among these, point‐defect engineering is the most widely adopted approach in electrode design [198]. By introducing vacancies, impurity atoms, or interstitial atoms into the crystal lattice, one can disrupt the periodic atomic arrangement, alter the local coordination environment and charge density, and ultimately regulate the surface physicochemical properties and electrical conductivity of the catalyst [199]. Common approaches for generating point defects include plasma etching, chemical reduction, thermal treatment, and heteroatom doping [200, 201]. Defect engineering has attracted considerable attention because the introduction of vacancies can effectively modify the local electronic environment and alter adsorption behavior during electrochemical reactions. Cation vacancies were introduced into cobalt oxides through regulation of the thermal‐treatment temperature of cobalt glycerolate precursors [202]. The generated Co vacancies induced delocalized charge redistribution on the oxide surface, which reduced the adsorption‐energy differences among reaction intermediates and facilitated more balanced catalytic pathways, thereby improving bifunctional catalytic activity. In addition to cation vacancies, O‐vacancy engineering has also demonstrated a strong influence on catalytic performance. Nanosheets enriched with O vacancies were synthesized through thermal treatment under an O2 atmosphere (Figure 5b) [180]. The coexistence of O vacancies and metal ions with different valence states generated synergistic effects that promoted both the formation and decomposition of Li2O2. Such interactions facilitated a solution‐mediated growth mechanism and contributed to enhanced discharge capacity. Furthermore, introducing dopants into TM oxides, such as incorporating Ag and Ce into α‐MnO2, can simultaneously generate abundant vacancies and modify the electronic distribution of the host material (Figure 5c) [181, 203]. These structural and electronic changes can affect charge‐transfer behavior and active‐site characteristics, leading to improved intrinsic catalytic activity and electrical conductivity. Composite Conductive Scaffolds Integrating catalytic materials with conductive scaffolds is an effective strategy to enhance the electronic conductivity of metal oxides during charge/discharge processes and to expose a greater number of active catalytic sites. Among these scaffolds, carbon‐based materials have received particular attention owing to their low cost, excellent electrical conductivity, and structural versatility, ranging from graphene and CNTs to various porous carbons [204, 205, 206]. The construction of integrated electrode architectures has been widely explored to simultaneously enhance conductivity, structural stability, and catalytic activity in LOBs. A 3D hierarchical porous carbonized‐melamine‐foam/graphene/Co‐CoO composite cathode (CMF‐G‐Co/CoO, Figure 5d) was developed using high‐temperature carbonized melamine as the structural backbone [182]. The interconnected conductive framework and intrinsic mechanical elasticity of the material effectively improved electrode stability during repeated cycling. Electrochemical and structural characterizations further indicated that synergistic interactions between Co/CoO and graphene regulated the initial nucleation behavior of discharge products, promoting preferential Li2O2 growth on Co/CoO sites during the early discharge stage. Such selective deposition behavior effectively suppressed parasitic reactions occurring at the carbon/LiO2 interface. The direct growth of active materials on conductive substrates provides another approach for constructing self‐supporting electrodes with enhanced transport properties. Mesoporous CoNi2S4 nanorod arrays grown directly on flexible carbon textiles through a two‐step hydrothermal process generated a self‐supporting cathode structure (CNS‐RAs/CT) [207]. The highly open architecture and large specific surface area increased the exposure of catalytic sites while supplying sufficient internal space for Li2O2 accommodation. These structural characteristics enabled the fabrication of a large‐area flexible pouch‐type LOB with an energy density of 484.29 Wh kg−1. Metallic scaffolds, including stainless‐steel meshes and nickel foams, have also attracted increasing attention as conductive supports because of their high electrical conductivity and mechanical robustness. Multilayer N‐doped CNTs directly grown on stainless‐steel mesh produced a self‐supporting and flexible electrode (N‐CNTs@SS) with favorable physicochemical characteristics [208]. The intimate integration between the conductive scaffold and active components reduced interfacial resistance and facilitated charge transport, allowing the corresponding LOB to maintain stable cycling over 232 cycles. Practical Relevance and System‐Level Considerations Although substantial efforts have focused on improving the intrinsic catalytic activity of MnOx‐based cathodes, the practical performance of LOBs is strongly influenced by system‐level interactions involving electrolytes, redox mediators, carbon supports, and Li metal anodes [209]. Therefore, the design of MnOx catalysts should not be considered independently but rather within an integrated battery environment. The interactions between MnOx catalysts and electrolyte systems are particularly important because reactive oxygen species and intermediate products generated during ORR/OER processes can initiate electrolyte decomposition [210]. The catalytic properties of MnOx may influence adsorption energies and reaction pathways of oxygen intermediates, thereby affecting the formation of parasitic products such as Li2CO3 and other irreversible species. Rational regulation of surface electronic structures and defect sites may therefore help suppress undesirable side reactions and improve reaction selectivity. In systems employing RMs, MnOx catalysts may also influence mediator activity through interfacial electronic interactions [211]. Proper matching between MnOx surface properties and mediator redox potentials could facilitate Li2O2 formation and decomposition pathways while reducing charge overpotentials. However, undesirable interactions may also lead to mediator degradation or additional parasitic reactions, indicating that catalyst–mediator compatibility requires further investigation. Furthermore, although MnOx catalysts cannot directly resolve Li metal degradation issues, they may indirectly improve system stability by lowering charging overpotentials and reducing the generation of highly reactive intermediates [212]. Such effects can mitigate electrolyte decomposition and alleviate detrimental reactions occurring at the Li metal anode. Summary and Perspective Non‐aqueous LOBs possess an ultrahigh theoretical energy density, approaching that of gasoline (∼1700 Wh kg−1), and are therefore regarded as one of the most promising next‐generation energy‐storage technologies. However, their practical implementation remains severely constrained. The dominant discharge product, solid and electrically insulating Li2O2, is insoluble in typical organic electrolytes and exhibits strong oxidizing characteristics. These intrinsic properties result in limited discharge capacities, large overpotentials, and poor cycling stability. During discharge, continuous accumulation of Li2O2 progressively passivates catalytic sites and blocks ion and mass transport pathways. Meanwhile, its high oxidizing nature triggers persistent parasitic reactions with the electrolyte. During charging, the insulating nature of Li2O2 drastically hampers charge transfer, leading to severe polarization and large OER overpotentials. When the charging voltage exceeds ∼4.35 V, undesirable decomposition of both the electrolyte and carbon materials is accelerated, causing irreversible damage to the electrode architecture. As the locus of both the ORR/OER, the cathode catalyst plays a vital role in lowering reaction barriers and determining overall electrochemical performance (Figure 6). Summary and perspective of MnOx materials for LOBs. An ideal cathode catalyst for high‐performance LOBs must simultaneously satisfy several criteria: i) High ORR and OER catalytic activity, enabling reduced overpotentials, complete decomposition of Li2O2, enhanced reaction reversibility, and improved energy efficiency; ii) Optimized micro‐/nanoporous architectures, capable of accommodating discharge products while maintaining channels for O2 diffusion and electrolyte infiltration, thereby enhancing capacity; iii) High electronic conductivity, which promotes rapid charge transport, suppresses polarization, and improves rate capability; iv) Abundant raw materials and low fabrication cost, which are essential for scaling toward practical applications. MnOx, as a representative family of TM‐based catalysts, offer several advantages: abundant natural reserves, low cost, and intrinsic catalytic activity. Although their relatively low electronic conductivity limits reaction kinetics and leaves significant room for improvement, the rich Mn valence states and diverse crystalline phases endow them with exceptional tunability. Therefore, rational structural and compositional engineering of MnOx, guided by established catalyst‐design strategies, offers a promising pathway for improving LOB performance and advancing practical applications. Nevertheless, the practical deployment of MnOx‐based catalysts requires consideration beyond intrinsic catalytic activity. Future development should emphasize system‐level optimization involving catalyst–electrolyte compatibility, interactions with redox mediators, suppression of parasitic chemistry, and stabilization of Li metal anodes. Rather than acting as standalone solutions, MnOx‐based catalysts are expected to function as key components within integrated LOB systems employing stable electrolytes, efficient redox mediators, and protected Li metal architectures. Moreover, future studies combining catalyst design with advanced operando characterization and theoretical calculations are expected to provide deeper insights into reaction pathways and dynamic catalyst evolution in MnOx‐based LOB systems. Such integrated approaches may facilitate the establishment of more reliable structure–activity relationships and accelerate the rational development of high‐performance MnOx cathode catalysts for practical LOB applications. Conflicts of Interest The authors declare no conflicts of interest. Acknowledgements Q.S. acknowledges financial support from the European Union's Horizon Europe Research and Innovation Programme under the Marie Skłodowska‐Curie Grant Agreement No. 101211154. This work was financially supported by the National Key R&D Program of China (Grant No. 2025YFE0125100), the ChirUP project (Grant No. PID2024‐162971OA‐I00) funded by MCIU/AEI/10.13039/501100011033, and the Generalitat de Catalunya (Grant No. 2021SGR01581). Biographies Ruiqin Peng obtained his M.Eng. from Shandong Normal University in 2012 and his Ph.D. from Harbin Institute of Technology in 2016. He subsequently conducted postdoctoral research at Shandong University and Jülich Research Centre, Helmholtz Association. In 2021, he joined Shandong Management University as an Associate Professor. His research focuses on electrochemical sensors and metal oxide materials for energy storage applications. Linna Dai received her B.Eng. in 2017 and Ph.D. in 2022 from Shandong University. Following the completion of her doctoral studies, she joined Hubei University of Technology as a Lecturer. Her research interests mainly focus on energy storage materials and electrochemical energy conversion systems, with particular emphasis on catalyst design for lithium‐oxygen batteries and the development of advanced cathode materials for sodium‐ion batteries. Qing Sun received his B.Eng. from the Harbin Institute of Technology (HIT) in 2014 and his Ph.D. from Shandong University in 2022. He subsequently carried out research at the Shenzhen campus and the Zhengzhou Advanced Research Institute of HIT. In 2025, he joined the Catalonia Institute for Energy Research as a Marie Skłodowska‐Curie Fellow. His research focuses on the development of advanced energy storage materials and flexible energy storage devices. Contributor Information Linna Dai, Email: dailinnuo@hbut.edu.cn. Qing Sun, Email: qsun@irec.cat. Data Availability Statement Data sharing not applicable to this article as no datasets were generated or analysed during the current study. References Associated Data Data Availability Statement Data sharing not applicable to this article as no datasets were generated or analysed during the current study.