Implementation and experimental validation of a hybrid intelligent sliding mode control strategy for induction motor drives Authors: Ngoc Thuy Pham Published: 2026 ABSTRACT This paper proposes a hybrid intelligent control strategy for high-performance induction motor drives under field-oriented control (FOC). The proposed architecture combines a radial basis function (RBF) neural network with higher-order non-singular terminal sliding-mode (HONTSM) control to improve robustness against nonlinear dynamics, parameter uncertainties, and external disturbances. The RBF network generates the torque-producing current reference in the speed loop, while the HONTSM compensator enhances disturbance rejection and tracking performance. In the inner loop, a HONTSM current controller ensures fast convergence, reduced chattering, and robust current regulation. To further enhance energy efficiency, an improved Kronecker-Factored Approximate Curvature (IK-FAC) flux optimization strategy is proposed to adaptively optimize the flux-producing current reference in real time. The proposed approach employs recursive curvature estimation based on filtered gradient-energy statistics to adaptively scale the flux update law without explicit Hessian computation or matrix inversion. Unlike the original K-FAC algorithm for large-scale neural network optimization, the proposed method reformulates the curvature-aware adaptation principle into a lightweight scalar recursive framework suitable for real-time embedded motor-drive applications. Consequently, the proposed IK-FAC strategy achieves fast convergence toward the minimum-loss operating trajectory while preserving the original FOC structure and maintaining low computational complexity for DSP-based induction motor drives. Controller parameters are optimized using particle swarm optimization (PSO) based on the integral absolute error (IAE) criterion. Experimental validation on a Texas Instruments TMS320F28379D digital signal processor demonstrates improved tracking accuracy, fast transient response, enhanced energy efficiency, and strong robustness under varying operating conditions. Introduction Induction motors (IMs) have been extensively utilized in industrial applications because of their rugged structure, low manufacturing cost, high reliability, and favorable operating characteristics. Owing to these advantages, IM drive systems are widely employed in industrial automation, electric transportation, robotic systems, and renewable-energy applications1,2. Nevertheless, achieving high-performance control of induction motor drives remains a challenging task because of their nonlinear behavior, strong coupling effects, parameter sensitivity, and susceptibility to external disturbances3,4. Therefore, improving the dynamic performance of these drives while simultaneously enhancing energy efficiency has become a critical objective in modern electric drive systems, particularly under partial-load conditions, where conventional control strategies often operate far from optimal efficiency. Among various control strategies, field-oriented control (FOC) has become one of the most widely adopted techniques for induction motor drives because it enables the decoupling of torque and flux components. In conventional FOC systems, proportional–integral (PI) controllers are commonly used in both the speed and current loops due to their simple structure and ease of implementation5–7. However, PI-based controllers often exhibit limited robustness when the system operates under parameter uncertainties, load disturbances, and nonlinear inverter dynamics, which may lead to degraded dynamic performance and larger tracking errors8–10. To overcome these limitations, various advanced nonlinear control strategies have been proposed in the literature. Sliding-mode control (SMC) has attracted significant attention due to its strong robustness against system uncertainties and external disturbances11–14. Nevertheless, conventional SMC methods suffer from the well-known chattering phenomenon, which may excite unmodeled dynamics and cause undesirable oscillations in motor drive systems15. To mitigate this issue, higher-order sliding-mode control (HOSM) techniques have been developed, among which non-singular terminal sliding-mode control (NTSM) provides finite-time convergence and improved robustness properties16–18. Another nonlinear control strategy, backstepping (BS), has also attracted significant attention from researchers due to its systematic Lyapunov-based design procedure and guaranteed closed-loop stability. By recursively constructing virtual control laws and stabilizing functions, backstepping enables the stabilization of nonlinear systems with strict-feedback structures, making it particularly suitable for induction motor drives under field-oriented control. Several studies have applied backstepping control to improve the dynamic response and robustness of motor drive systems19–23. However, conventional backstepping approaches often rely heavily on accurate system models and are sensitive to parameter uncertainties and external disturbances. Moreover, the design may suffer from performance degradation when unmodeled nonlinearities or load variations are present. In recent years, intelligent control approaches such as neural networks and fuzzy logic systems have been increasingly investigated for motor drive applications24–35. Among these methods, radial basis function (RBF) neural networks have gained considerable attention due to their strong nonlinear approximation capability, simple structure, and fast learning characteristics. RBF networks have been successfully applied to estimate system uncertainties, approximate nonlinear mappings, and improve the adaptability of control systems without requiring precise knowledge of motor parameters34,35. Despite these advances, many existing studies employ intelligent techniques and nonlinear control strategies independently, which limits their capability to simultaneously address nonlinear dynamics, parameter uncertainties, and external disturbances. Several hybrid intelligent nonlinear control strategies for induction motor drives have been proposed in the literature36–41 to improve the dynamic performance of field-oriented controlled induction motor drives. In36, a radial basis function (RBF) neural network was introduced to adaptively tune controller parameters online, improving the adaptability over conventional PI-based approaches. Nevertheless, the RBF network was mainly employed as a gain-tuning mechanism rather than as an explicit uncertainty estimator. Consequently, the control scheme still relied on PI-based regulation, which inherently limited its capability to effectively handle strong nonlinearities, parameter uncertainties, and external disturbances. To overcome these limitations, an adaptive BS nonlinear control strategy in38 has been investigated to enhance the capability of induction motor drives in dealing with system nonlinearities, where fuzzy logic was employed to tune the backstepping gains and enhance dynamic performance. Although this strategy improved adaptability and reduced sensitivity to parameter variations, the fuzzy logic component mainly served as a gain-tuning mechanism and did not provide an explicit mechanism for uncertainty estimation or disturbance compensation. To further enhance robustness and disturbance rejection capability, hybrid nonlinear control strategies combining backstepping with sliding-mode control have been proposed. In particular, an advanced adaptive higher-order sliding-mode (NAHOSM) control scheme integrated with backstepping was introduced in40, where the sliding-mode dynamics significantly improved disturbance rejection in the inner control loop. However, the outer speed-loop design in this approach remained primarily model-based and did not incorporate any data-driven mechanism to learn or compensate for unknown nonlinear dynamics. Motivated by the aforementioned limitations and the absence of a unified control framework that can simultaneously provide nonlinear uncertainty estimation, finite-time robust control, and real-time energy-efficiency optimization within a conventional FOC architecture, this work proposes a hybrid intelligent control architecture that combines a radial basis function (RBF) neural network with a higher-order nonsingular terminal sliding-mode (HONTSM) control strategy for induction motor drives. This development reflects the evolution of induction motor control strategies from conventional PI-based regulation toward first order sliding-mode (SM)36, and higher-order sliding-mode control frameworks STASOSM38—NAHOSM40. Building upon these developments, the proposed architecture further extends the state of the art by incorporating a higher-order nonsingular terminal sliding-mode (HONTSM) controller in the inner current-control loop. The adoption of HONTSM enables the controller to preserve the inherent robustness and disturbance-rejection capability of sliding-mode control while significantly alleviating the chattering phenomenon through higher-order continuous control action and finite-time convergence properties. In the outer speed-control loop, the proposed RBF neural network is fundamentally different from existing approaches in which neural networks are primarily employed as auxiliary gain-tuning mechanisms for PI controllers36 or as supplementary adaptive elements in adaptive backstepping-based schemes38. Instead, the RBF network directly participates in nonlinear uncertainty estimation and torque-current reference generation, thereby providing an adaptive data-driven mechanism capable of compensating for unknown dynamics and parameter variations in real time. Furthermore, HONTSM dynamics are systematically incorporated into both the disturbance-compensation mechanism of the outer speed loop and the inner current-control loop, establishing a coordinated robust-control framework. As a result, the proposed strategy simultaneously achieves fast transient response, finite-time convergence, strong robustness against disturbances and parameter uncertainties, improved current-regulation quality and disturbance attenuation, and enhanced closed-loop stability under varying operating conditions. Furthermore, the effectiveness of advanced nonlinear controllers strongly depends on proper parameter selection. In many existing studies, controller parameters are commonly adjusted using heuristic procedures or trial-and-error tuning methods, which are often time-consuming and may not guarantee satisfactory control performance under different operating conditions42–45. To overcome this limitation, particle swarm optimization (PSO) is adopted in this work for offline optimization of the proposed controller parameters. The optimization process is formulated based on minimization of the integral absolute error (IAE) associated with the speed-tracking response, thereby improving transient behavior, tracking accuracy, and the overall operational efficiency of the induction motor drive system. In addition to dynamic performance and robustness, energy efficiency has become an increasingly important requirement in modern induction motor drive systems, particularly in industrial automation, electric vehicles, and energy-sensitive applications46. In conventional field-oriented control systems, the flux-producing current is typically maintained at a fixed or conservatively selected value to ensure stable operation under varying load conditions. However, this approach often results in excessive excitation current under partial-load operation, leading to increased copper losses and reduced overall drive efficiency. Consequently, various flux optimization and loss-minimization strategies have been investigated to improve the energy efficiency of induction motor drives47–49. Most existing approaches employ first-order optimization methods or heuristic search mechanisms to determine the optimal reference. These conventional first-order adaptive optimization methods often exhibit slow convergence and sensitivity to the local geometry of nonlinear objective functions50. To overcome these limitations, second-order optimization techniques exploiting Hessian or curvature information have attracted considerable attention due to their superior convergence behaviour51,52. Nevertheless, explicit Hessian computation and matrix inversion generally impose excessive computational complexity for real-time embedded control applications. Recently, Hessian-free approximation and Kronecker-factored curvature estimation methods have been proposed to reduce computational burden while preserving the advantages of second-order optimization53,54. Motivated by these developments, This paper introduces an Improved Kronecker-Factored Approximate Curvature (IK-FAC) flux optimization strategy employing a lightweight curvature-aware adaptation mechanism suitable for online energy-efficient induction motor drive applications. The main contributions of this paper are summarized as follows: A novel hybrid intelligent control framework integrating a radial basis function (RBF) neural network with higher-order non-singular terminal sliding-mode (HONTSM) control is proposed for high-performance induction motor drives under field-oriented control. In this framework, Unlike existing RBF-based approaches where the neural network is primarily used for parameter tuning, the proposed method employs the RBF network as an explicit nonlinear uncertainty estimator to directly generate the torque-producing current reference in the speed loop, while an auxiliary HONTSM compensation mechanism is incorporated to enhance disturbance rejection and improve speed tracking performance. A robust HONTSM controller is developed for the current control loop to ensure finite-time convergence, strong robustness against parameter variations, and reduced chattering effects.Particle swarm optimization (PSO) is employed as an offline global optimization framework to simultaneously determine the optimal parameters of the RBF network and the HONTSM controller by minimizing the integral absolute error (IAE) of the speed tracking error, thereby achieving improved convergence speed, reduced steady-state error, and enhanced robustness under varying operating conditions.An improved Kronecker-Factored Approximate Curvature (IK-FAC) flux optimization strategy is proposed to adaptively optimize the flux-producing current reference in real time for energy-efficient induction motor drives. Unlike conventional first-order optimization approaches, the proposed method employs recursive curvature estimation derived from filtered gradient-energy statistics to adaptively scale the flux update law without requiring explicit Hessian computation or matrix inversion. The proposed optimization framework preserves the original FOC structure while maintaining low computational complexity suitable for real-time DSP-based implementation.The effectiveness of the proposed control strategy is validated through MATLAB/Simulink simulations and real-time experimental implementation on a DSP platform based on the Texas Instruments TMS320F28379D processor. A novel hybrid intelligent control framework integrating a radial basis function (RBF) neural network with higher-order non-singular terminal sliding-mode (HONTSM) control is proposed for high-performance induction motor drives under field-oriented control. In this framework, Unlike existing RBF-based approaches where the neural network is primarily used for parameter tuning, the proposed method employs the RBF network as an explicit nonlinear uncertainty estimator to directly generate the torque-producing current reference in the speed loop, while an auxiliary HONTSM compensation mechanism is incorporated to enhance disturbance rejection and improve speed tracking performance. A robust HONTSM controller is developed for the current control loop to ensure finite-time convergence, strong robustness against parameter variations, and reduced chattering effects. A novel hybrid intelligent control framework integrating a radial basis function (RBF) neural network with higher-order non-singular terminal sliding-mode (HONTSM) control is proposed for high-performance induction motor drives under field-oriented control. In this framework, Unlike existing RBF-based approaches where the neural network is primarily used for parameter tuning, the proposed method employs the RBF network as an explicit nonlinear uncertainty estimator to directly generate the torque-producing current reference in the speed loop, while an auxiliary HONTSM compensation mechanism is incorporated to enhance disturbance rejection and improve speed tracking performance. A robust HONTSM controller is developed for the current control loop to ensure finite-time convergence, strong robustness against parameter variations, and reduced chattering effects. Particle swarm optimization (PSO) is employed as an offline global optimization framework to simultaneously determine the optimal parameters of the RBF network and the HONTSM controller by minimizing the integral absolute error (IAE) of the speed tracking error, thereby achieving improved convergence speed, reduced steady-state error, and enhanced robustness under varying operating conditions. Particle swarm optimization (PSO) is employed as an offline global optimization framework to simultaneously determine the optimal parameters of the RBF network and the HONTSM controller by minimizing the integral absolute error (IAE) of the speed tracking error, thereby achieving improved convergence speed, reduced steady-state error, and enhanced robustness under varying operating conditions. An improved Kronecker-Factored Approximate Curvature (IK-FAC) flux optimization strategy is proposed to adaptively optimize the flux-producing current reference in real time for energy-efficient induction motor drives. Unlike conventional first-order optimization approaches, the proposed method employs recursive curvature estimation derived from filtered gradient-energy statistics to adaptively scale the flux update law without requiring explicit Hessian computation or matrix inversion. The proposed optimization framework preserves the original FOC structure while maintaining low computational complexity suitable for real-time DSP-based implementation. An improved Kronecker-Factored Approximate Curvature (IK-FAC) flux optimization strategy is proposed to adaptively optimize the flux-producing current reference in real time for energy-efficient induction motor drives. Unlike conventional first-order optimization approaches, the proposed method employs recursive curvature estimation derived from filtered gradient-energy statistics to adaptively scale the flux update law without requiring explicit Hessian computation or matrix inversion. The proposed optimization framework preserves the original FOC structure while maintaining low computational complexity suitable for real-time DSP-based implementation. The effectiveness of the proposed control strategy is validated through MATLAB/Simulink simulations and real-time experimental implementation on a DSP platform based on the Texas Instruments TMS320F28379D processor. The effectiveness of the proposed control strategy is validated through MATLAB/Simulink simulations and real-time experimental implementation on a DSP platform based on the Texas Instruments TMS320F28379D processor. The remainder of this paper is organized as follows. Section "Mathematical description Of IMDS" reviews the mathematical model of the induction motor and the principles of field-oriented control (FOC). Section "Design of the hybrid intelligent proposed control architecture" presents the proposed hybrid intelligent control strategy, including the RBF neural network-based speed controller, the HONTSM current controller, the PSO-based parameter optimization framework, and the proposed IK-FAC flux optimization strategy for energy-efficient operation. Section "Experimental discussion" presents the experimental setup, real-time implementation details, and performance evaluation results under various operating conditions. Finally, Section “Conclusion” concludes the paper and discusses future research directions. Mathematical description Of IMDS This section presents the fundamental IM model in the synchronously rotating reference frame, which decouples flux and torque dynamics, serves as the basis for constructing the improved RBF–HONTSM control algorithms based on FOC in the following section. To enhance clarity and assist readers in following the mathematical derivations, the main symbols and parameters used throughout the paper are summarized in Nomenclature list. The state-space model representation can be mathematically written as the following equation:1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{x}\left( t \right){\text{ = A}}x\left( t \right) + Bu\left( t \right)$$\end{document}where: x, A, B and u can be defined as: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$x\left( t \right) = \left[ {\begin{array}{*{20}l} {i_{{s\alpha }} } \hfill & {i_{{s\beta }} } \hfill & {\varphi _{{r\alpha }} } \hfill & {\varphi _{{r\beta }} } \hfill & {\omega _{r} } \hfill \\ \end{array} } \right]^{T} ;\;u\left( t \right) = \left[ {\begin{array}{*{20}c} {u_{{s\alpha }} } & {u_{{s\beta }} } & {T_{L} } \\ \end{array} } \right]^{T}$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$A = \left[ {\begin{array}{*{20}l} {a_{{11}} } \hfill & 0 \hfill & {a_{{13}} } \hfill & {a_{{14}} } \hfill & {a_{{15}} } \hfill \\ 0 \hfill & {a_{{11}} } \hfill & { - a_{{14}} } \hfill & {a_{{13}} } \hfill & {a_{{25}} } \hfill \\ {{\raise0.7ex\hbox{${L_{m} }$} \!\mathord{\left/ {\vphantom {{L_{m} } {\tau _{r} }}}\right.\kern-\nulldelimiterspace} \!\lower0.7ex\hbox{${\tau _{r} }$}}} \hfill & 0 \hfill & {{\raise0.7ex\hbox{${ - 1}$} \!\mathord{\left/ {\vphantom {{ - 1} {\tau _{r} }}}\right.\kern-\nulldelimiterspace} \!\lower0.7ex\hbox{${\tau _{r} }$}}} \hfill & {\omega _{r} } \hfill & {\varphi _{{r\beta }} } \hfill \\ 0 \hfill & {{\raise0.7ex\hbox{${L_{m} }$} \!\mathord{\left/ {\vphantom {{L_{m} } {\tau _{r} }}}\right.\kern-\nulldelimiterspace} \!\lower0.7ex\hbox{${\tau _{r} }$}}} \hfill & { - \omega _{r} } \hfill & {{\raise0.7ex\hbox{${ - 1}$} \!\mathord{\left/ {\vphantom {{ - 1} {\tau _{r} }}}\right.\kern-\nulldelimiterspace} \!\lower0.7ex\hbox{${\tau _{r} }$}}} \hfill & { - \varphi _{{r\alpha }} } \hfill \\ { - b\varphi _{{r\beta }} } \hfill & {b\varphi _{{r\alpha }} } \hfill & {bi_{{s\beta }} } \hfill & { - bi_{{s\alpha }} } \hfill & {\left( {{\raise0.7ex\hbox{${ - B}$} \!\mathord{\left/ {\vphantom {{ - B} J}}\right.\kern-\nulldelimiterspace} \!\lower0.7ex\hbox{$J$}}} \right)} \hfill \\ \end{array} } \right];\;B = \left[ {\begin{array}{*{20}l} {{\raise0.7ex\hbox{$1$} \!\mathord{\left/ {\vphantom {1 {\sigma L_{s} }}}\right.\kern-\nulldelimiterspace} \!\lower0.7ex\hbox{${\sigma L_{s} }$}}} \hfill & 0 \hfill & 0 \hfill \\ 0 \hfill & {{\raise0.7ex\hbox{$1$} \!\mathord{\left/ {\vphantom {1 {\sigma L_{s} }}}\right.\kern-\nulldelimiterspace} \!\lower0.7ex\hbox{${\sigma L_{s} }$}}} \hfill & 0 \hfill \\ 0 \hfill & 0 \hfill & 0 \hfill \\ 0 \hfill & 0 \hfill & 0 \hfill \\ 0 \hfill & 0 \hfill & {{\raise0.7ex\hbox{${ - 1}$} \!\mathord{\left/ {\vphantom {{ - 1} J}}\right.\kern-\nulldelimiterspace} \!\lower0.7ex\hbox{$J$}}} \hfill \\ \end{array} } \right]$$\end{document} with:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\tau_{r} = \frac{{L_{r} }}{{R_{r} }};\;\sigma = 1 - \frac{{L_{m}^{2} }}{{L_{r} L_{s} }};\;\gamma = \frac{{L_{m} }}{{L_{r} }};\;k = \frac{{3pL_{m} }}{{2L_{r} }};\;b = \frac{k}{J}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$a_{11} = - \frac{1}{{\sigma L_{s} }}\left( {R_{s} + \frac{{L_{m}^{2} }}{{L_{r} \tau_{r} }}} \right);\;a_{13} = \frac{\gamma }{{\sigma L_{s} \tau_{r} }};\;a_{14} = - \frac{\gamma }{{\sigma L_{s} }}\omega_{r} ;\;a_{15} = - \frac{\gamma }{{\sigma L_{s} }}\varphi_{r\beta } ;\;a_{25} = \frac{\gamma }{{\sigma L_{s} }}\varphi_{r\alpha }$$\end{document} Based on the dynamics of IM in stator fixed reference frame, the stator flux can be estimated such as:2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{*{20}c} {\varphi_{s\alpha } = \int_{0}^{t} {\left( {u_{s\alpha } - R_{s} i_{s\alpha } } \right)dt} } \\ {\varphi_{s\beta } = \int_{0}^{t} {\left( {u_{s\beta } - R_{s} i_{s\beta } } \right)dt} } \\ \end{array} } \right.$$\end{document} The stator and rotor flux linkage phase is given by (3):3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varphi_{s} = \sqrt {\varphi_{s\alpha }^{2} + \varphi_{s\beta }^{2} } ;\quad \varphi_{r} \approx \frac{{L_{m} }}{{L_{r} }}\varphi_{s}$$\end{document} Torque can be calculated such as:4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{e} = \frac{3}{2}p\left( {i_{s\beta } \varphi_{s\alpha } - i_{s\alpha } \varphi_{s\beta } } \right)$$\end{document} The mechanical dynamics follow:5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$J\frac{{d\omega_{r} }}{dt} = T_{e} - T_{L} - B\omega_{r}$$\end{document} Design of the hybrid intelligent proposed control architecture RBF-HONTSMC speed controller RBF adpative controller The proposed RBF neural network is introduced in the outer speed loop as an adaptive nonlinear compensation mechanism to approximate the nonlinear speed–torque relationship and compensate for lumped uncertainties, parameter variations, and external disturbances. Unlike conventional RBF-based approaches in which the neural network is mainly employed for gain tuning, the proposed structure utilizes the RBF network to directly generate the torque-producing current component for the induction motor drive system. Therefore, the adaptive mechanism acts as a bounded nonlinear compensator that enhances the tracking capability of the HONTSMC-based speed controller while preserving the robustness characteristics of the sliding-mode dynamics. The input variables of the RBF network are selected as the speed tracking error and its discrete variation, defined as:6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} e\left( k \right) = \omega_{r}^{*} \left( t \right) - \omega_{r} \left( t \right) \hfill \\ \Delta e\left( k \right) = e\left( k \right) - e\left( {k - 1} \right) \hfill \\ \end{gathered}$$\end{document} To improve numerical stability and ensure reproducibility, the input variables are normalized into the interval [ - 1, 1]. The RBF network consists of nine Gaussian basis functions uniformly distributed over a 3 × 3 grid in the normalized error space. The output of each neuron is expressed as7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\phi_{j} \left( x \right) = \exp \left( { - \frac{{\left\| {x - c_{j} } \right\|^{2} }}{{2\sigma^{2} }}} \right);\;x = \left[ {\begin{array}{*{20}c} {e\left( k \right)} \\ {\Delta e\left( k \right)} \\ \end{array} } \right]$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$c_{j} = \left[ {c_{j,e} ,\,c_{{j,\dot{e}}} } \right]^{T}$$\end{document} are pre-defined centers and σ is the RBF width. In this work, the Gaussian centers are selected from the normalized coordinates \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ { - 1,0,1} \right\}$$\end{document}. Since the exponential function satisfies \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0 < \exp \left( { - z} \right) \le 1$$\end{document} for all z \ge 0, it follows directly that: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0 < \phi_{j} \left( x \right) \le 1$$\end{document}. For a network containing N = 9 neurons. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\| {\phi \left( x \right)} \right\|^{2} = \sum\limits_{j = 1}^{N} {\phi_{j}^{2} \left( x \right) \le N}$$\end{document} which implies \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\| {\phi \left( x \right)} \right\| \le \sqrt N$$\end{document}. Hence, the basis vector \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\phi \left( x \right)$$\end{document} is globally bounded. The adaptive gains are obtained as:8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} K_{p} \left( t \right) = K_{p,pso} + W_{p}^{T} \phi \left( x \right) \hfill \\ K_{i} \left( t \right) = K_{i,pso} + W_{i}^{T} \phi \left( x \right) \hfill \\ \end{gathered}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{p} ,pso$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{i} ,pso$$\end{document} are the initial gains optimized offline using the PSO procedure presented in "Offline parameter optimization using PSO" section. The adaptive weights are updated online according to the normalized gradient adaptation law:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{W}_{p} = - \eta_{p} \frac{\phi \left( x \right)e\left( k \right)}{{\left\| {\phi \left( x \right)} \right\|^{2} + \varepsilon }};\;\dot{W}_{i} = - \eta_{i} \frac{\phi \left( x \right)e\left( k \right)}{{\left\| {\phi \left( x \right)} \right\|^{2} + \varepsilon }}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$n_{p} = 0.8$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$n_{i} = 0.3$$\end{document}​ are learning rates, and \varepsilon = 1e - 6 is introduced to avoid numerical singularity when \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\| {\phi \left( x \right)} \right\| \to 0$$\end{document}. To prevent parameter drift and improve numerical stability during real-time implementation, the adaptive weights are constrained within the projection bound: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$W \in \left[ { - 10^{3} ,10^{3} } \right]$$\end{document}. Taking norms gives:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left| {\dot{W}_{p} } \right| \le \eta_{p} \frac{{\left\| {\phi \left( x \right)} \right\|\left| {e\left( k \right)} \right|}}{{\left\| {\phi \left( x \right)} \right\|^{2} + \varepsilon }} \le \frac{{\eta_{p} }}{\varepsilon }\left\| {\phi \left( x \right)} \right\|\left| {e\left( k \right)} \right|$$\end{document} Since \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\| {\phi \left( x \right)} \right\| \le \sqrt N$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$e\left( k \right)$$\end{document} the tracking error is bounded under the previously established sliding-mode dynamics, there exists a constant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$C_{p} > 0$$\end{document} such that: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\| {\dot{W}_{p} } \right\| \le C_{p}$$\end{document} Therefore, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$W_{p} \left( t \right)$$\end{document} is bounded for all t. The same conclusion holds for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$W_{i} \left( t \right)$$\end{document}. Moreover, the explicit projection constraint \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$W \in \left[ { - 10^{3} ,10^{3} } \right]$$\end{document} further guarantees global boundedness of the neural weights. Using the Cauchy–Schwarz inequality: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$W_{p}^{T} \phi \left( x \right) \le \left\| {W_{p} } \right\|\left\| {\phi \left( x \right)} \right\|$$\end{document} and since both terms are bounded, the adaptive gains satisfy: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left| {K_{p} \left( t \right)} \right| \le K_{p,max} ;\;\left| {K_{i} \left( t \right)} \right| \le K_{i,max}$$\end{document} for some positive constants \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{p,max} ,K_{i,max}$$\end{document}. Thus, the PI gains remain bounded during online adaptation. The \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sq\_RBF}^{*} \left( k \right)$$\end{document} control signal is:9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sq\_RBF}^{*} \left( k \right) = i_{sq\_RBF}^{*} \left( {k - 1} \right) + K_{p} \left( t \right)\Delta e\left( k \right) + K_{i} \left( t \right)e\left( k \right)$$\end{document} Because \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{p} \left( t \right);\;K_{i} \left( t \right);\;e\left( k \right)$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta e\left( k \right)$$\end{document} are all bounded, the incremental term in (9) is bounded. Consequently, there exists a constant M > 0 such that \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sq\_RBF}^{*} \left( k \right) \le M$$\end{document}. Therefore, the RBF adaptive mechanism generates a bounded control component. HONTSMC disturbance observer The proposed control architecture combines higher-order sliding-mode control (HOSMC) with nonsingular terminal sliding-mode control (NTSMC) to achieve finite-time convergence, enhanced robustness, and reduced chattering in induction motor speed regulation. The HOSMC component improves disturbance rejection and mitigates chattering by utilizing higher-order sliding dynamics, whereas the NTSMC structure introduces a nonlinear terminal sliding surface that accelerates convergence near the equilibrium point while avoiding singularity problems. By integrating these complementary control characteristics, the proposed controller maintains high tracking accuracy and robust dynamic performance in the presence of parameter uncertainties, external load disturbances, and measurement noise. Accordingly, the proposed sliding surface is defined as follows:10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s\left( t \right) = e\left( t \right) + \alpha \left| e \right|^{p/q} sat\left( {\frac{e}{\zeta }} \right)$$\end{document}with: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\alpha > 0;\;\zeta > 0\;\& \;0 < \frac{p}{q} < 1$$\end{document}; The parameters α and p/q are optimized offline using the PSO optimization procedure. The saturation function is introduced to reduce excessive switching activity and improve numerical smoothness near the origin. Taking the time derivative of the sliding surface yields. The derivative of the sliding surface is given by:11\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{s}\left( t \right) = \dot{e}\left( t \right) + \alpha \frac{p}{q}\left| e \right|^{{\left( {p/q} \right) - 1}} sat\left( {\frac{e}{\xi }} \right) + \alpha \left| e \right|^{{\left( {p/q} \right)}} \frac{d}{dt}sat\left( {\frac{e}{\xi }} \right)$$\end{document} Assume that the motor parameters, load disturbances, inverter nonlinearities, and adaptive RBF compensation signals are bounded during system operation. To analyze the closed-loop stability, the Lyapunov candidate function is selected as:12\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$V = \frac{1}{2}s^{2} \left( t \right)$$\end{document}its derivative can obtain:13\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}} = s\left( t \right)\dot{s}\left( t \right)$$\end{document} To satisfy: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}} < 0$$\end{document} Then: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s\left( t \right)\dot{s}\left( t \right) < 0$$\end{document}. From Eq. (11), a HONTSMC control law is designed as follows:14\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{s}\left( t \right) = - \beta u_{HONTSMC} \left( t \right)$$\end{document}where:15\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u_{HONTSMC} \left( t \right) = \frac{{f_{1} \left( s \right)}}{{f_{2} \left( s \right)}}$$\end{document}with:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f_{1} \left( s \right) = \dddot s + \frac{{\left[ {\left( {\ddot{s} + \dot{s} + \left| s \right|^{3/4} sat\left( s \right)} \right)\left( {\left| {\dot{s}} \right| + \left| s \right|^{3/4} } \right)^{{\left( { - 1/3} \right)}} } \right]}}{{\left[ {\dot{s} + \left( {\left| {\dot{s}} \right| + \left| s \right|^{3/4} } \right)^{{\left( {2/3} \right)}} } \right]^{1/2} }};\;f_{2} \left( s \right) = \left| {\dddot s} \right| + \left[ {\left| {\dot{s}} \right| + \left( {\left| {\dot{s}} \right| + \left| s \right|^{3/4} } \right)^{{\left( {2/3} \right)}} } \right]^{1/2}$$\end{document} This designed control law ensures the sliding existence condition \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s\left( t \right)\dot{s}\left( t \right) < 0$$\end{document} is satisfied for all admissible uncertainties, guaranteeing that system trajectories reach and remain on the sliding manifold. Combining Eq. (5), (6), (11), (15) and substituting the IM dynamics into the sliding condition the virtual control vector isq is designed as follows:16\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u\left( t \right) = k_{t} \left\{ {J\dot{\omega}_{r}^{*} + B\omega_{r}^{*} + T_{L} + \beta u_{HONTSMC} \left( t \right)} \right\}$$\end{document} β is positive constant and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$k_{t} = \frac{{2L_{r} }}{{3pL_{m} \varphi_{r} }}$$\end{document}. Combining Eq. (13), (14), (15) and (16) we get:17\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}} = s\left( t \right)\dot{s}\left( t \right) = - \beta s\left( t \right)u_{HONTSMC} \left( t \right)$$\end{document} We notice that β and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f_{2} \left( s \right)$$\end{document} are always positive definite regardless of the sign of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s\left( t \right)$$\end{document} . So the sign of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}}$$\end{document} depends only on the sign relationship between \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s\left( t \right)$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f_{1} \left( s \right)$$\end{document}. From the definition of the sliding surface in Eq. (7), the sign of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f_{1} \left( s \right)$$\end{document} remains consistent with the sign of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s\left( t \right)$$\end{document}. Specifically, when \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s\left( t \right) > 0$$\end{document}, it follows that \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f_{1} \left( s \right)$$\end{document}, whereas \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s\left( t \right) < 0$$\end{document} leads to \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f_{1} \left( s \right) < 0$$\end{document}. Therefore, the following condition is always satisfied: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s\left( t \right)f_{1} \left( s \right) > 0;\quad \forall s\left( t \right)$$\end{document}. From Eq. (15) we have:18\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}} = s\left( t \right)\dot{s}\left( t \right) = - \beta s\left( t \right)u_{HONTSMC} \left( t \right) < 0\forall e\left( t \right)$$\end{document} Therefore, under the designed gain conditions and bounded disturbances, the closed-loop system satisfies Lyapunov stability criteria and ensures asymptotic convergence of the sliding variable. Combining Eq. (9) and Eq. (16) the new virtual control vector isq is designed:19\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sq}^{*} \left( t \right) = i_{sq\_RBF}^{*} \left( k \right) + u\left( t \right)$$\end{document} To analyze the influence of the adaptive RBF compensation on the closed-loop stability, the sliding dynamics are decomposed into nominal HONTSMC dynamics and an additional perturbation term generated by the adaptive RBF mechanism:20\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{s}\left( t \right) = \dot{s}_{0} \left( t \right) + \Delta_{RBF}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{s}_{0} \left( t \right)$$\end{document} denotes the nominal sliding dynamics generated by the HONTSMC control law \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u\left( t \right)$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta_{RBF}$$\end{document} represents the additional term introduced by the adaptive RBF compensation. From the previous subsection, the Gaussian basis functions, adaptive weights, adaptive gains, and RBF-generated current component are all proven to be bounded. Consequently, the RBF-induced perturbation term is also bounded. Therefore, there exists a positive constant M > 0 such that \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left| {\Delta_{RBF} \left( t \right)} \right| \le M$$\end{document}21\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s\left( t \right)s_{0} \left( t \right) \le - k\left| {s\left( t \right)} \right| < 0$$\end{document} Based on the boundedness of the Gaussian basis functions, the projection-constrained adaptive weights, and the bounded adaptive gains established in "RBF adpative controller" section, together with the bounded motor parameters in the control channel, the RBF-induced term \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta_{RBF}$$\end{document} is uniformly bounded; therefore, there exists a positive constant M > 0 such that |ΔRBF (t)| ≤ M. Taking the time derivative of V: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}} = s\left( t \right)\dot{s}\left( t \right)$$\end{document}. Substituting (22),22\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}} = s\left( t \right)\dot{s}_{0} \left( t \right) + s\left( t \right)\Delta_{RBF}$$\end{document} Using inequalities (21) and (22)23\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{V}\left( t \right) \le - \beta \left| {s\left( t \right)} \right| + \left| {s\left( t \right)} \right|\left| {\Delta_{RBF} \left( t \right)} \right|$$\end{document} Equation (23) reveals that the closed-loop stability characteristics are determined by the interaction between the finite-time stabilizing action induced by the HONTSMC law and the bounded perturbation associated with the adaptive RBF compensation mechanism. Specifically, the term \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$- \beta \left| {s\left( t \right)} \right|$$\end{document} represents the dissipative component responsible for enforcing sliding-surface attractivity, whereas the term \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left| {s\left( t \right)} \right|\left| {\Delta_{RBF} \left( t \right)} \right|$$\end{document} characterizes the residual uncertainty introduced by the adaptive neural approximation process. Since the adaptive RBF perturbation is uniformly bounded according to (21), the following inequality is obtained:24\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{V}\left( t \right) \le - \beta \left| {s\left( t \right)} \right| + M\left| {s\left( t \right)} \right| \le - \left( {\beta - M} \right)\left| {s\left( t \right)} \right|\quad$$\end{document} Therefore, the asymptotic dominance of the nominal HONTSMC dynamics over the adaptive perturbation component can be guaranteed by appropriately selecting the switching gain β such that:β > M. This condition ensures that the dissipative energy induced by the higher-order sliding dynamics exceeds the worst-case effect of the bounded RBF-induced perturbation throughout the entire operating domain. Consequently, the adaptive neural compensation mechanism does not compromise the inherent stability properties of the nominal sliding-mode subsystem. Defining: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\eta = \beta - M > 0$$\end{document}. we obtain:25\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{V}\left( t \right) \le - \eta \left| {s\left( t \right)} \right| \le 0$$\end{document} Equation (25) establishes that the Lyapunov function is strictly monotonically decreasing along the closed-loop system trajectories, thereby guaranteeing global Lyapunov stability of the proposed control architecture. Furthermore, because the Lyapunov derivative is upper bounded by a negative definite function proportional to \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left| {s\left( t \right)} \right|$$\end{document}, the corresponding sliding dynamics satisfy the finite-time reachability condition. Hence, the sliding trajectories are driven toward the sliding manifold within finite time despite the presence of bounded adaptive neural compensation, parameter uncertainties, and external load disturbances. HONTSM current controllers The following tracking errors are defined:26\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{*{20}c} {e_{isd} = i_{sd}^{*} - i_{sd} } \\ {e_{isq} = i_{sq}^{*} - i_{sq} } \\ \end{array} } \right.$$\end{document} To guarantee finite-time convergence and avoid singularities, the proposed sliding surface is defined as:27\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s_{j} (t) = e_{j} (t) + \alpha_{j} \left| {e_{j} } \right|^{p/q} sat\left( {\frac{{e_{j} }}{{\zeta_{j} }}} \right);\quad j = \left\{ {isd;isq} \right\}{\mathrm{w}}ith:\;\alpha_{j} > 0;\;\zeta_{j} > 0\;\& \;0 < \frac{p}{q} < 1$$\end{document} The derivative of the sliding surface is given by:28\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{s}_{j} (t) = \dot{e}_{j} (t) + \alpha_{j} \frac{p}{q}\left| {e_{j} } \right|^{{\left( {p/q} \right) - 1}} sat\left( {\frac{{e_{j} }}{{\zeta_{j} }}} \right) + \alpha_{j} \left| {e_{j} } \right|^{{\left( {p/q} \right)}} \frac{d}{dt}\left[ {sat\left( {\frac{{e_{j} }}{{\zeta_{j} }}} \right)} \right]$$\end{document} The Lyapunov function is selected as:29\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$V\left( t \right) = \frac{1}{2}s_{j}^{2} \left( t \right) = \frac{1}{2}\left[ {s_{isd}^{2} \left( t \right) + s_{isq}^{2} \left( t \right)} \right]$$\end{document}its derivative can obtain:30\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}} = s_{j} \left( t \right)\dot{s}_{j} \left( t \right) = s_{isd} \left( t \right)\dot{s}_{isd} \left( t \right) + s_{isq} \left( t \right)\dot{s}_{isq} \left( t \right)$$\end{document} To satisfy: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}} < 0$$\end{document} Then: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s_{j} \left( t \right)\dot{s}_{j} \left( t \right) < 0$$\end{document}. From Eq. (28), a HONTSM control law is designed as follows:31\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{s}\left( t \right) = - u_{HONTSMC} \left( t \right) = - \left[ {\beta_{j} u_{{_{j} }} \left( t \right)} \right]$$\end{document}where:32\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u_{j} \left( t \right) = \frac{{f_{j1} \left( {s_{j} } \right)}}{{f_{j2} \left( {s_{j} } \right)}}$$\end{document} With:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f_{j1} \left( {s_{j} } \right) = \dddot s_{j} + \frac{{\left[ {\left( {\ddot{s}_{j} + \dot{s}_{j} + \left| {s_{j} } \right|^{3/4} sat\left( {s_{j} } \right)} \right)\left( {\left| {\dot{s}_{j} } \right| + \left| {s_{j} } \right|^{3/4} } \right)^{{\left( { - 1/3} \right)}} } \right]}}{{\left[ {\dot{s}_{j} + \left( {\left| {\dot{s}_{j} } \right| + \left| {s_{j} } \right|^{3/4} } \right)^{{\left( {2/3} \right)}} } \right]^{1/2} }};\;f_{j2} \left( {s_{j} } \right) = \left| {\dddot s_{j} } \right| + \left[ {\left| {\dot{s}_{j} } \right| + \left( {\left| {\dot{s}_{j} } \right| + \left| {s_{j} } \right|^{3/4} } \right)^{{\left( {2/3} \right)}} } \right]^{1/2}$$\end{document} Combining Eq. (1), (28), (31), (32) and substituting the IM dynamics into the sliding condition the virtual control vector isq is designed as follows:33\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{*{20}c} {u_{sd}^{*} (k) = \frac{{L_{s} }}{c}\left\{ {\frac{{di_{sd}^{*} }}{dt} + ai_{sd} - \, L_{s} \omega_{e} i_{sq} - \, b\psi_{rd} + u_{isd} \left( t \right)} \right\}} \\ {u_{sq}^{*} (k) = \frac{{L_{s} }}{c}\left\{ {\frac{{di_{sq}^{*} }}{dt} + ai_{sq} - \, L_{s} \omega_{e} i_{sd} - \, b_{r} \omega_{e} \psi_{rd} + u_{isq} \left( t \right)} \right\}} \\ \end{array} } \right.$$\end{document} Combining formulas (27), (30), (31) and (33) we get:34\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}} = s_{j} \left( t \right)\dot{s}_{j} \left( t \right) = - \beta_{j} s_{j} \left( t \right)u_{j} \left( t \right)$$\end{document}where: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\beta_{j}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f_{j2} \left( s \right)$$\end{document} are always positive definite regardless of the sign of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s_{j} \left( t \right)$$\end{document} . So the sign of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}}$$\end{document} depends entirely on the sign of: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s_{j} \left( t \right)f_{j1} \left( t \right)$$\end{document}. If \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$e_{j} (t) > 0$$\end{document}, from Eq. (23) we have \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s_{j} \left( t \right) > 0$$\end{document} then \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f_{j1} \left( t \right) > 0$$\end{document}. If \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$e_{j} (t) < 0$$\end{document}, from Eq. (23) we have \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s_{j} \left( t \right) < 0$$\end{document} then \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f_{j1} \left( t \right) < 0$$\end{document}. Therefore: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$s_{j} \left( t \right)f_{j1} \left( t \right) > 0\quad \forall \,e_{j} \left( t \right)$$\end{document}. From Eq. (30) we have:35\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{dV\left( t \right)}{{dt}} = s\left( t \right)\dot{s}\left( t \right) = - \beta_{j} s_{j} \left( t \right)u_{j} \left( t \right) < 0\,\forall \,e_{j} \left( t \right)$$\end{document} Thus, the system is always stable according to Lyapunov stability theory. Offline parameter optimization using PSO The dynamic performance of the proposed RBF–HONTSM-IKFAC control system depends strongly on the appropriate selection of several key speed-loop parameters, including the proportional gain, integral gain, and nonlinear sliding-surface coefficients. Owing to the highly nonlinear nature of induction motor drives and the strong coupling between the adaptive neural compensator and the terminal sliding-mode controller, conventional trial-and-error tuning often leads to suboptimal performance and poor reproducibility. To address this issue, Particle Swarm Optimization (PSO) is employed as an offline global optimization framework to automatically determine the controller parameters. Compared with gradient-based optimization approaches, PSO does not require differentiability of the objective function and exhibits reduced sensitivity to local minima. Furthermore, PSO provides an effective balance between optimization quality, implementation simplicity, and computational efficiency, making it particularly suitable for nonlinear controller tuning problems. It should be emphasized that the PSO algorithm is utilized exclusively during the controller-design stage. Once the optimal parameter vector is obtained, the optimization process is terminated and the resulting parameters remain fixed during real-time operation. Therefore, PSO does not participate in the online control loop and does not contribute to the computational burden of the DSP implementation. The subsequent dynamic performance, robustness, and energy-efficiency characteristics are governed by the RBF adaptive compensator, the HONTSM controllers, and the IK-FAC optimization layer. The overall optimization procedure is summarized in Fig. 1.Fig. 1The PSO optimization procedure. The PSO optimization procedure. The optimization objective is to determine the optimal controller parameter vector:36\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$X = \left[ {K_{p,pso} ,\,K_{i,pso} ,\alpha ,\,\left( {p/q} \right)} \right]$$\end{document} The optimization problem can be formulated as:37\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$X^{*} = \arg \,\mathop {\min }\limits_{X \in \Omega } \,J\left( X \right)$$\end{document}subject to: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$X_{\min } \le X \le X_{\max }$$\end{document}. where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$X_{\min }$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$X_{\max }$$\end{document} denote the lower and upper parameter bounds used to ensure numerical stability and physically realizable controller gains during the optimization process. The optimization variables are selected as the most influential speed-loop parameters of the proposed controller. The resulting optimal parameter set determines the transient-response characteristics of the drive system, including tracking accuracy, settling time, overshoot, and disturbance-rejection capability. However, the closed-loop stability of the proposed architecture is established independently through the Lyapunov-based design of the HONTSM controller and bounded adaptive laws, while PSO serves only as a performance-oriented tuning tool operating within the admissible stability region. To evaluate the dynamic performance of the speed control system, the Integral Time Absolute Error (ITAE) criterion is adopted due to its effectiveness in penalizing long-duration tracking errors and improving transient characteristics. The performance index is defined as:38\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$J = \int_{0}^{T} t \left| {\omega_{ref} \left( t \right) - \omega \left( t \right)} \right|dt$$\end{document} Minimizing the ITAE criterion enables the controller to achieve reduced settling time, smaller steady-state tracking error, and improved dynamic response under varying operating conditions. In PSO, each candidate solution is represented by a particle in the search space. The swarm consists of N particles that explore the solution space simultaneously. Each particle updates its velocity and position according to both its own best experience and the best solution found by the entire swarm. The velocity update rule is expressed as:39\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$V_{i}^{k + 1} = wV_{i}^{k} + \delta_{1} r_{1} \left( {P_{i} - X_{i}^{k} } \right) + \delta_{2} r_{2} \left( {G - X_{i}^{k} } \right)$$\end{document}where: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$V_{i}^{k}$$\end{document} is the velocity of particle i at iteration k; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$X_{i}^{k}$$\end{document} is the particle position; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$P_{i}$$\end{document} is the personal best position of particle i; G is the global best position of the swarm; w is the inertia weight; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{1}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{2}$$\end{document} are acceleration coefficients; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$r_{1}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$r_{2}$$\end{document} are random numbers uniformly distributed in [0 1]. The position update is given by:40\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$X_{i}^{k} = X_{i}^{k} + V_{i}^{k + 1}$$\end{document} Because PSO is inherently stochastic, the robustness and repeatability of the optimization process were evaluated through multiple independent optimization runs using different random initial populations. The obtained solutions consistently converged toward similar objective-function values and parameter sets, indicating satisfactory robustness and reproducibility of the adopted optimization configuration. A sensitivity investigation was also conducted around the optimal parameter vector. The analysis revealed that the optimized controller gains primarily influence transient-response characteristics rather than closed-loop stability. Specifically, larger values of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{p,pso}$$\end{document} generally improve tracking responsiveness and reduce rise time, whereas excessive values may increase overshoot and control activity. The integral gain \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{i,pso}$$\end{document} mainly affects steady-state accuracy and disturbance-rejection capability. The nonlinear sliding-surface coefficient α determines the aggressiveness of the HONTSM dynamics, while the exponent ratio \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {p/q} \right)$$\end{document} governs the finite-time convergence behavior. Moderate parameter perturbations around the optimized solution mainly affect settling time, ripple amplitude, and convergence speed, whereas the overall stability properties remain preserved. The robustness of the offline optimization process was also assessed with respect to the swarm parameters ((nPop, MaxIter, w, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{1}$$\end{document}, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{2}$$\end{document}). Increasing the swarm size and iteration number generally improves the probability of locating near-global optimal solutions but increases offline computational effort. The inertia weight (w) governs the exploration–exploitation trade-off, whereas the acceleration coefficients \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{1}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{2}$$\end{document} balance individual exploration and social learning. The selected parameter set shown in Table 1 consistently produced high-quality solutions while maintaining low optimization cost. The parameters used in the optimization are summarized in Table 1.Table 1The parameters optimization.ParameternPopMaxIterw_maxw_min\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{1}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{2}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{p,gapso}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{i,gapso}$$\end{document}αp/qValue10150.90.5223.51.60.453/4 Table 1The parameters optimization.ParameternPopMaxIterw_maxw_min\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{1}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{2}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{p,gapso}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{i,gapso}$$\end{document}αp/qValue10150.90.5223.51.60.453/4 The parameters optimization. IK-FAC curvature-aware flux optimization for induction motor drives In induction motor drive systems, energy efficiency is governed by the nonlinear interaction between copper losses and core losses, which are directly dependent on the current distribution in the dq reference frame. Under steady-state operating conditions, the total power loss can be expressed as a function of the control variables:41\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$P_{loss} = R_{s} \left( {i_{sd}^{2} + i_{sq}^{2} } \right) + R_{r} i_{sq}^{2} + k_{fe} \varphi_{s}^{2} \omega_{e}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$k_{fe}$$\end{document} is the core loss coefficient and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\omega_{e}$$\end{document} is the electrical angular speed. Under the FOC framework, the stator flux is approximated linearly as \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varphi_{s} = L_{m} i_{sd}$$\end{document}, which allows the loss function to be fully expressed in terms of the current components:42\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$P_{loss} \left( {i_{sd} ,\;i_{sq} } \right) = R_{s} \left( {i_{sd}^{2} + i_{sq}^{2} } \right) + R_{r} i_{sq}^{2} + k_{fe} L_{m}^{2} i_{sd}^{2} \omega_{e}$$\end{document} By incorporating the torque constraint:43\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{e} = \frac{3p}{2}L_{m} i_{sd} i_{sq}$$\end{document}the torque-producing current can be expressed as:44\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sq} = \frac{{2T_{e} }}{{3pL_{m} i_{sd} }}$$\end{document} Substituting into the loss expression yields a single-variable nonlinear optimization problem:45\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$P_{loss} \left( {i_{sd} } \right) = R_{s} i_{sd}^{2} + \left( {R_{s} + R_{r} } \right)\left( {\frac{{2T_{e} }}{{3pL_{m} i_{sd} }}} \right)^{2} + k_{fe} L_{m}^{2} i_{sd}^{2} \omega_{e}$$\end{document} This expression is not merely a mathematical formulation but reflects a fundamental physical principle: the drive system inherently possesses an optimal operating point at which the trade-off between excitation losses and torque-related copper losses is balanced. This defines the optimal efficiency trajectory that the controller must track. The function \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$P_{loss} \left( {i_{sd} } \right)$$\end{document} exhibits a convex-like structure over the feasible domai \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd} > 0$$\end{document}, as it consists of quadratic and inverse quadratic terms. Therefore, there exists at least one global minimum corresponding to the optimal flux level for each operating condition \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {T_{e} ,\omega_{e} } \right)$$\end{document}. The derivative of the loss function with respect to \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd}$$\end{document} reveals the nonlinear and curvature characteristics of the problem:46\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$P_{loss} \left( {i_{sd} } \right) = R_{s} i_{sd}^{2} + \left( {R_{s} + R_{r} } \right)\left( {\frac{{2T_{e} }}{{3pL_{m} i_{sd} }}} \right)^{2} + k_{fe} L_{m}^{2} i_{sd}^{2} \omega_{e}$$\end{document} From a theoretical standpoint, the optimal point can be obtained by solving this equation. However, real-time implementation is not feasible due to the strong nonlinearity and continuous variation of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{e}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\omega_{e}$$\end{document}. This leads to a fundamental requirement: an optimization strategy that is both fast, stable, and sufficiently accurate for real-time tracking of the optimal point. First-order methods such as gradient descent are simple but fail to exploit curvature information, resulting in slow convergence and strong dependence on step-size tuning. In contrast, classical second-order methods such as Newton’s method achieve faster convergence but require explicit Hessian computation and matrix inversion, which are impractical for embedded systems due to high computational complexity and sensitivity to parameter uncertainties. Inspired by curvature-aware optimization principles employed in IK-FAC methods, a lightweight adaptive flux optimization strategy is proposed to improve convergence behavior while maintaining low computational complexity suitable for embedded motor drive applications. Instead of explicitly computing the Hessian matrix, the proposed approach estimates local curvature information using filtered gradient statistics and utilizes this information to adaptively scale the optimization update law. The gradient of the loss function is computed as:47\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$g\left( {i_{sd} } \right) = 2R_{s} i_{sd} - 2R_{s} \frac{{i_{sq}^{2} }}{{i_{sd}^{3} }} + 2k_{fe} \omega_{e}^{2} i_{sd}$$\end{document} To improve robustness against measurement noise and rapid operating-condition variations, the gradient signal is filtered using a first-order recursive filter:48\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$g_{f} \left( k \right) = \left( {1 - \gamma } \right)g_{f} \left( {k - 1} \right) + \gamma g\left( k \right)$$\end{document}where 0 < γ < 1 is the gradient filtering coefficient. The local curvature information is then recursively estimated according to:49\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$C_{est} \left( k \right) = \lambda C_{est} \left( {k - 1} \right) + \left( {1 - \lambda } \right)g_{f}^{2} \left( k \right)$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\lambda \in \left( {0,1} \right)$$\end{document} is the curvature memory factor controlling the trade-off between historical and instantaneous curvature information. The term \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$C_{est} \left( k \right)$$\end{document} acts as a lightweight approximation of the local curvature characteristics of the loss function. The recursive curvature estimator in Eq. (49) does not represent the exact Hessian of the loss function. Instead, it serves as a lightweight local sensitivity indicator derived from the filtered gradient energy. Physically, the quantity \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$g_{f}^{2} \left( k \right)$$\end{document} reflects how rapidly the total drive loss changes with respect to variations in the excitation current reference. Large values of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$g_{f}^{2} \left( k \right)$$\end{document} indicate operating regions where small changes in isd produce significant variations in power loss, corresponding to high local sensitivity of the loss surface. Conversely, small values of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$g_{f}^{2} \left( k \right)$$\end{document} indicate that the operating point is approaching the minimum-loss region, where the loss function becomes relatively flat. The recursive averaging mechanism governed by λ enables the estimator to capture the long-term curvature tendency while suppressing measurement noise and transient fluctuations. Therefore, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$C_{est} \left( k \right)$$\end{document} provides a practical approximation of local curvature information without requiring explicit second-order derivatives, making it suitable for real-time embedded motor-drive applications. Based on the estimated curvature information, the adaptive inverse scaling factor is obtained as:50\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Gamma \left( k \right) = \frac{1}{{\sqrt {C_{est} \left( k \right)} + \varepsilon_{c} }}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varepsilon_{c} > 0$$\end{document} is introduced to avoid numerical singularity and improve numerical stability during real-time implementation. The curvature-aware correction term is then computed as:51\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta i_{sd} \left( k \right) = - \beta g_{f} \left( k \right)\Gamma \left( k \right)$$\end{document}where β denotes the adaptive learning rate. The adaptive scaling mechanism in (50) introduces a curvature-dependent effective learning rate. When the loss function exhibits high sensitivity, the estimated curvature increases, resulting in a smaller scaling factor \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Gamma \left( k \right)$$\end{document} and consequently reducing the update magnitude. This behavior prevents excessive excitation-current variations and improves numerical robustness. In contrast, when the operating point approaches the minimum-loss trajectory, the estimated curvature decreases, allowing larger adaptive updates and accelerating convergence toward the optimal operating condition. Unlike conventional fixed-step gradient-descent methods, the proposed approach automatically adjusts the adaptation gain according to the local geometry of the loss surface. Therefore, the optimization process becomes less sensitive to manual parameter tuning and exhibits improved convergence smoothness under varying operating conditions. To preserve stable operation over the entire operating range, the optimization process is initialized using a flux trajectory similar to the conventional MTPA structure:52\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd,base} = k\sqrt {\left| {i_{q} } \right|}$$\end{document} The optimized flux-producing current reference is constructed as:53\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd}^{*} \left( k \right) = i_{sd,base} + \mu \Delta i_{sd} \left( k \right)$$\end{document}where μ is the correction weighting coefficient. To suppress abrupt current variations and improve smoothness during transient operating conditions, the optimized current is updated using the first-order smoothing law:54\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd,opt}^{*} \left( k \right) = i_{sd,opt}^{*} \left( {k - 1} \right) + \zeta \left[ {i_{sd}^{*} \left( k \right) - i_{sd,opt}^{*} \left( {k - 1} \right)} \right]$$\end{document}where ζ is the smoothing coefficient controlling the adaptation speed. To ensure stability and practical feasibility, the optimized current is constrained within allowable limits:55\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd,\min } \le i_{sd,opt}^{*} \left( k \right) \le i_{sd,\max }$$\end{document} From (50), the adaptive scaling factor satisfies \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0 < \Gamma \left( k \right) \le 1/\sqrt {\varepsilon_{c} }$$\end{document} because \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$C_{est} \left( k \right) \ge 0$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varepsilon_{c} > 0$$\end{document}, Consequently, the correction term \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta i_{sd} \left( k \right)$$\end{document} remains uniformly bounded for all operating conditions. Furthermore, because the loss function in Eq. (45) exhibits a convex-like structure over the feasible domain and possesses at least one stationary point corresponding to the minimum-loss operating condition, the gradient magnitude decreases as the optimization trajectory approaches the optimum region. Consequently, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$g_{f} \left( k \right) \to 0$$\end{document}. Substituting into Eq. (51) gives \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta i_{sd} \left( k \right) \to 0$$\end{document} which implies that the excitation-current update naturally diminishes near the optimum. Therefore, the proposed curvature-aware adaptation law inherently suppresses oscillatory behavior around the minimum-loss trajectory and improves convergence smoothness. Since the adaptation magnitude is proportional to the filtered gradient while remaining bounded by the curvature-dependent scaling factor, the proposed optimization process preserves stability and enables reliable online tracking of the optimal excitation-current reference under varying speed and load conditions. The implementation procedure of the proposed IK-FAC curvature-aware flux optimization strategy is illustrated in Fig. 2. The parameters employed in the proposed optimization algorithm are summarized in Table 2.Fig. 2Flowchart of IK-FAC Algorithm.Table 2Parameters of the Proposed IK-FAC Curvature-Aware Optimization Strategy.Parameterαβλγ\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varepsilon_{c}$$\end{document}μζk\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd,min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd,max}$$\end{document}Value0.010.020.9950.351e-20.20.030.450.153.5 Flowchart of IK-FAC Algorithm. Table 2Parameters of the Proposed IK-FAC Curvature-Aware Optimization Strategy.Parameterαβλγ\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varepsilon_{c}$$\end{document}μζk\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd,min}$$\end{document}\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd,max}$$\end{document}Value0.010.020.9950.351e-20.20.030.450.153.5 Parameters of the Proposed IK-FAC Curvature-Aware Optimization Strategy. The proposed optimization strategy only updates the flux-producing current reference \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${i}_{d}^{*}$$\end{document}, while preserving the original FOC structure. Therefore, the proposed method can be directly integrated into existing induction motor drive systems without modifying the internal current and speed control loops. Compared with classical second-order optimization methods such as Newton-based approaches, the proposed IK-FAC strategy avoids explicit Hessian computation and matrix inversion while still exploiting local curvature information through recursive gradient-energy estimation. Consequently, the computational complexity is significantly reduced and becomes suitable for real-time DSP implementation. Compared with conventional adaptive gradient methods employing fixed learning rates, the proposed curvature-aware scaling mechanism automatically adjusts the effective adaptation gain according to the local sensitivity of the loss function. This property improves convergence behavior, numerical robustness, and noise tolerance while reducing dependence on manual parameter tuning. As a result, the proposed optimization strategy achieves a favorable trade-off between convergence speed, computational efficiency, and implementation simplicity for energy-efficient induction motor drives. Closed-loop stability analysis of the integrated RBF–HONTSM–IKFAC framework The stability analyses presented in Sects. "RBF-HONTSMC speed controller" and "HONTSM current controllers" establish the convergence properties of the proposed RBF–HONTSM speed controller and HONTSM current controller under bounded disturbances and parameter uncertainties. However, the complete control architecture additionally incorporates the IK-FAC-based flux adaptation mechanism, which continuously updates the flux-producing current reference according to the operating condition. Unlike a conventional fixed-flux FOC scheme, the proposed architecture introduces an additional adaptive control channel through the online regulation of the excitation current reference. Since the rotor flux directly influences the electromagnetic torque production mechanism, the IK-FAC optimization process becomes dynamically coupled with both the speed-control and current-control loops. Consequently, the stability of the overall closed-loop system cannot be inferred solely from the individual stability analyses of the RBF–HONTSM controllers and requires an additional investigation of the interaction between the flux adaptation mechanism and the electromechanical dynamics. To address this issue, the following analysis demonstrates that the IK-FAC adaptation process generates bounded flux references and preserves the boundedness properties required by the previously established Lyapunov stability conditions. As a result, the adaptive flux optimization mechanism contributes to energy-efficiency improvement without compromising the closed-loop stability of the integrated control framework. Proposition 1 Boundedness of the IK-FAC Internal Signals. To improve robustness against measurement noise and rapid operating-condition variations, the gradient signal is filtered using a first-order recursive filter as Eq. (48): \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$g_{f} \left( k \right) = \left( {1 - \gamma } \right)g_{f} \left( {k - 1} \right) + \gamma g\left( k \right)$$\end{document} where 0 < γ < 1 is the gradient filtering coefficient. The Eq. (48) represents a first-order stable discrete-time filter. Therefore, bounded gradient inputs produce bounded filtered outputs. Consequently,56\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$g\left( k \right) \in L_{\infty } \quad \Rightarrow g_{f} \left( k \right) \in L_{\infty }$$\end{document} The curvature estimator is updated according to Eq. (49): \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$C_{est} \left( k \right) = \lambda C_{est} \left( {k - 1} \right) + \left( {1 - \lambda } \right)g_{f}^{2} \left( k \right)$$\end{document} where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\lambda \in \left( {0,1} \right)$$\end{document}. Since \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$g_{f} \left( k \right)$$\end{document} is bounded and the recursion is exponentially stable, the estimated curvature remains bounded: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$C_{est} \left( k \right) \in L_{\infty }$$\end{document}. The adaptive inverse-scaling factor is defined as Eq. (50):\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Gamma \left( k \right) = \frac{1}{{\sqrt {C_{est} \left( k \right)} + \varepsilon_{c} }}$$\end{document} with \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varepsilon_{c} > 0$$\end{document}. Because \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$C_{est} \left( k \right) \ge 0$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varepsilon_{c} > 0$$\end{document}, the denominator is strictly positive. Therefore:57\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0 < \Gamma \left( k \right) \le \frac{1}{{\sqrt {\varepsilon_{c} } }}$$\end{document}which guarantees that the adaptive scaling factor remains uniformly bounded. The curvature-aware correction term is then obtained as: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$- \mu g_{f} \left( k \right)\Gamma \left( k \right)$$\end{document}. Since both \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$g_{f} \left( k \right)$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Gamma \left( k \right)$$\end{document} are bounded signals, their product is also bounded. Therefore, there exists a positive constant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$M_{d}$$\end{document} such that:58\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left| {\Delta i_{d} \left( k \right)} \right| \le M_{d}$$\end{document} Hence, all signals of the IK-FAC optimization algorithm remain bounded under all operating conditions. Proposition 2 Boundedness of the Optimized Flux Reference. The optimized excitation-current reference is updated according to Eq. (54): \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd,opt}^{*} \left( k \right) = i_{sd,opt}^{*} \left( {k - 1} \right) + \zeta \left[ {i_{sd}^{*} \left( k \right) - i_{sd,opt}^{*} \left( {k - 1} \right)} \right]$$\end{document} where 0 < ζ < 1. Since the update law is a stable first-order discrete-time recursion, bounded input signals produce bounded outputs. Furthermore, the practical implementation explicitly enforces the constraint as Eq. (55): \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i_{sd,\min } \le i_{sd,opt}^{*} \left( k \right) \le i_{sd,\max }$$\end{document}. Consequently, the optimized excitation-current reference remains bounded throughout the entire operating range. Proposition 3 Boundedness of Rotor Flux and Electromagnetic Torque Gain. Under rotor-flux-oriented control, the rotor flux can be approximated as:59\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varphi_{rd} = L_{m} i_{sd,opt}$$\end{document} Using the result of Proposition 2, the rotor flux satisfies:60\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left| {i_{sd,opt} } \right| \le i_{sd.max} \quad \Rightarrow \left| {\varphi_{rd} } \right| \le L_{m} i_{sd.max}$$\end{document} Hence, the rotor flux remains uniformly bounded. The electromagnetic torque is expressed as:61\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{e} = \frac{3p}{2}\frac{{L_{m} }}{{L_{r} }}\varphi_{rd} i_{sq}$$\end{document} Defining the torque coefficient:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$k_{t} = \frac{3p}{2}\frac{{L_{m} }}{{L_{r} }}\varphi_{rd}$$\end{document}, the torque equation becomes:62\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{e} = k_{t} i_{sq}$$\end{document} Since \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varphi_{rd}$$\end{document} is bounded, it follows that:63\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left| {k_{t} } \right| \le \frac{{3pL_{m}^{2} }}{{2L_{r} }}i_{sd,max}$$\end{document} Therefore, the torque-production gain remains bounded during the entire IK-FAC adaptation process. This result demonstrates that the optimization layer only modifies the excitation level within a finite admissible region and does not introduce singularities or unbounded variations into the electromechanical dynamics. Proposition 4 Preservation of Closed-Loop Stability. The Lyapunov stability analyses established in Sects. "RBF-HONTSMC speed controller" and "HONTSM current controllers" were derived under the assumption that the motor states, rotor flux, adaptive neural-network outputs, and external disturbances remain bounded. From Proposition 1–3, the IK-FAC adaptation process generates bounded correction signals, bounded excitation-current references, bounded rotor flux, and bounded electromagnetic torque coefficients. Therefore, there exists a positive constant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$M_{T}$$\end{document} such that: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left| {T_{e} } \right| \le M_{T}$$\end{document}. Considering the mechanical dynamics of the induction motor as Eq. (5): \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$J\frac{{d\omega_{r} }}{dt} = T_{e} - T_{L} - B\omega_{r}$$\end{document}. The rotor-speed dynamics can be rewritten as:64\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{\omega}_{r} = - \frac{B}{J}\omega_{r} + \frac{1}{J}\left( {T_{e} - T_{L} } \right)$$\end{document} Since B > 0, the above equation represents a stable first-order system driven by the bounded input \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {T_{e} - T_{L} } \right)$$\end{document}. Because both \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {T_{e} } \right)$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {T_{L} } \right)$$\end{document} are bounded, it follows from the BIBO stability property that the rotor speed remains bounded. Consequently, the speed-tracking error65\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$e\left( k \right) = \omega_{r}^{*} \left( k \right) - \omega_{r} \left( k \right)$$\end{document}and its variation remain bounded. Since these signals constitute the inputs of the RBF neural network, the Gaussian basis functions, adaptive weights, and neural-network outputs remain within the admissible bounded region established in "RBF-HONTSMC speed controller" section. Therefore, the boundedness conditions required by the adaptive RBF mechanism and the HONTSM control laws remain satisfied during the entire online flux-adaptation process. Although the IK-FAC algorithm continuously updates the excitation-current reference and consequently affects the rotor flux and torque-production gain, these variations remain confined within finite admissible bounds and do not introduce singularities or unbounded dynamics into the electromechanical subsystem. As a result, the coupled interaction among the IK-FAC optimizer, the adaptive RBF network, and the HONTSM controllers preserves the boundedness assumptions required by the Lyapunov analyses developed in Sects. "RBF-HONTSMC speed controller" and "HONTSM current controllers". Consequently, the stability properties previously established for the RBF–HONTSM control system remain valid in the presence of the proposed online flux-adaptation mechanism. Therefore, the proposed IK-FAC optimization layer acts as a bounded supervisory adaptation mechanism and does not alter the stability properties established for the underlying RBF–HONTSM control system. Hence, all closed-loop signals remain bounded, and the integrated RBF–HONTSM–IKFAC framework preserves the Lyapunov stability properties of the overall induction motor drive system under bounded disturbances, adaptive neural compensation, online flux adaptation, and parameter uncertainties. Experimental discussion The experimental validation was carried out on a laboratory-scale induction motor drive platform. The setup consists of a three-phase two-level voltage source inverter (VSI) supplying a 1/4 HP squirrel-cage induction motor rated at 220 V. The induction motor parameters used in the experiments are as follows: p = 2, f = 50 Hz, J = 0.0003 kg.m2 \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$R_{s} = 9.8\;\Omega ,R_{r} = 9.6\;\Omega ,L_{s} = 0.311\;H,L_{r} = 0.311\;H,L_{m} = 0.29\;H.$$\end{document} A 750-W permanent magnet synchronous motor (PMSM), model HS758-080–02,430-17M-H0 manufactured by Powmax, rated at 220 VAC, 3.8 A, and 3000 r/min, is mechanically coupled via a rigid shaft and employed as a programmable load machine. The PMSM is driven by a Powmax POWSD-EQ-20ASB servo drive, operating in torque-control mode, to emulate variable load disturbances as well as rated-load operating conditions. The proposed control strategy was experimentally implemented on a Texas Instruments TMS320F28379D digital signal processor (DSP). The field-oriented control (FOC) algorithm, including the proposed optimization strategy, current controllers, coordinate transformations, PWM generation, and protection routines, was executed in real time using MATLAB/Simulink Embedded Coder and deployed directly to the DSP platform. Real-time communication between the DSP and MATLAB/Simulink was established through the XCP-over-Serial interface using COM2 communication with SCI_A configuration at a baud rate of 5 Mbps. Experimental variables were monitored online using the Monitor & Tune functionality of Simulink External Mode, enabling real-time acquisition and visualization of motor speed, stator currents, electromagnetic torque, and DC-link voltage without interrupting the controller execution. Rotor position and speed information were acquired using a Qphase™ incremental encoder (model 3138A001-2048–0), providing A/B/Z quadrature outputs with a resolution of 2048 pulses per revolution. The encoder signals were processed via the eQEP peripheral of the DSP to achieve high-resolution speed feedback required for vector control implementation. The stator phase currents were measured using isolated analog current-sensing circuits based on AMC1301 isolation amplifiers combined with MCP6002 signal-conditioning stages. The measured current signals were filtered and level-shifted to match the ADC input range of the DSP. Similarly, the phase voltages and DC-link voltage were measured using isolated voltage-sensing circuits employing AMC1301-based isolation stages and analog conditioning networks. The analog outputs of current sensors were sampled by the internal ADC modules of the TMS320F28379D controller. To ensure repeatability and signal consistency, all experimental waveforms were acquired under steady-state conditions. The measured signals were streamed from the DSP to MATLAB/Simulink via the Monitor & Tune interface and processed in MATLAB for performance evaluation. The acquired datasets were utilized to compute efficiency, power losses, and transient performance indices under various operating conditions. The PMSM-based load system was configured in accordance with the manufacturer’s torque-control specifications using an external analog torque reference applied through the VREF terminal of the servo drive. The servo drive parameters were tuned following the POWSD-EQ-20ASB torque-control configuration procedure to achieve controllable mechanical loading conditions over the entire operating range. To further demonstrate the practical applicability of the proposed control architecture, a comprehensive computational complexity, memory utilization, and real-time feasibility analysis was conducted on the experimental platform based on the Texas Instruments TMS320F28379D DSP operating at 200 MHz. The implementation results are summarized in Table 3.Table 3DSP Resource Utilization and Estimated Real-Time Computational Requirements.MetricPIRBF-HONTSMRBF-HONTSM-IKFACSampling period (μs)100100100Flash usage (kB)21.82929.23Flash utilization (%)2.132.832.86RAM usage (kB)27.229.729.74RAM utilization (%)13.314.5614.58Estimated CPU execution time (μs) < 10 ~ 15–20 ~ 30–35Sampling frequency (kHz)101010 Table 3DSP Resource Utilization and Estimated Real-Time Computational Requirements.MetricPIRBF-HONTSMRBF-HONTSM-IKFACSampling period (μs)100100100Flash usage (kB)21.82929.23Flash utilization (%)2.132.832.86RAM usage (kB)27.229.729.74RAM utilization (%)13.314.5614.58Estimated CPU execution time (μs) < 10 ~ 15–20 ~ 30–35Sampling frequency (kHz)101010 DSP Resource Utilization and Estimated Real-Time Computational Requirements. The conventional PI controller exhibits the lowest computational burden because only proportional and integral operations are executed during each sampling period. Consequently, the online computational complexity remains constant and can be characterized as O(1). For the RBF–HONTSM controller, the online implementation additionally includes a fixed-size RBF neural network consisting of nine Gaussian basis functions together with adaptive weight updating. Since the number of neurons remains constant during operation, the computational complexity can be expressed as O(N), where N denotes the number of RBF neurons. Because N = 9 is fixed, the computational burden remains bounded and suitable for real-time implementation. The proposed RBF–HONTSM–IKFAC controller further introduces a curvature-aware flux optimization layer. However, unlike conventional second-order optimization methods, the proposed IK-FAC algorithm does not require online Hessian computation, matrix inversion, eigenvalue decomposition, or iterative numerical optimization. The online adaptation process only involves recursive gradient filtering, scalar curvature estimation, adaptive gain scaling, and a first-order current-reference update law. Therefore, the overall computational complexity remains O(N), identical to that of the RBF-based controller, while providing additional energy-optimization capability. To quantify the computational burden, an operation-count analysis was performed for each module of the proposed controller. The RBF adaptive controller consists of nine Gaussian basis functions, adaptive gain computation, and online weight updating, resulting in approximately 180 floating-point operations (FLOPs) per control cycle. The HONTSM disturbance observer requires the evaluation of nonlinear sliding surfaces, saturation functions, fractional-order power terms, and switching laws, contributing approximately 100 FLOPs. The dual HONTSM current controllers implemented in the d-axis and q-axis channels represent the most computationally intensive part of the architecture because each controller evaluates nonlinear sliding manifolds and higher-order switching functions. Together, the two current controllers require approximately 200 FLOPs per sampling period. The proposed IK-FAC optimizer performs gradient evaluation, recursive filtering, curvature estimation, adaptive scaling, and flux-reference updating, contributing approximately 40 FLOPs. Finally, the remaining FOC operations, including coordinate transformations, flux estimation, current-reference generation, and PWM updating, require approximately 150 FLOPs. Accordingly, the total computational cost of the proposed architecture is approximately 670 FLOPs per control cycle. Considering the floating-point arithmetic capability of the TMS320F28379D DSP and accounting for interrupt handling, memory access overhead, ADC acquisition, and PWM update operations, the total execution time can be conservatively estimated from the required processor cycles. Assuming an average cost of four CPU cycles per floating-point operation, the proposed controller requires approximately 2680 processor cycles. At a clock frequency of 200 MHz, this corresponds to a theoretical execution time of approximately 13.4 μs. To account for practical implementation overhead, a conservative scaling factor of 2–2.5 is applied, resulting in an estimated execution time of approximately 30–35 μs per control cycle. For comparison, the conventional PI controller requires less than 10 μs per control cycle, whereas the RBF–HONTSM controller requires approximately 15–20 μs due to the additional neural-network computations and nonlinear sliding-mode operations. Although the proposed controller introduces the IK-FAC optimization layer, its contribution to the overall execution time remains relatively small because the algorithm consists only of scalar recursive operations and does not involve computationally intensive matrix calculations. The memory utilization results further confirm the lightweight nature of the proposed strategy. The Flash memory requirement increases from 21.8 kB for the PI controller to 29.23 kB for the proposed controller, corresponding to only 2.86% of the available program memory of the TMS320F28379D. Similarly, the RAM consumption increases from 27.2 kB to 29.74 kB, representing approximately 14.58% of the available data memory. These results indicate that the proposed control architecture introduces only a modest memory overhead despite integrating adaptive neural control, higher-order sliding-mode control, and online flux optimization. It should be emphasized that the PSO algorithm is employed exclusively during the offline controller-design stage to determine the optimal controller parameters. Once the optimal parameter vector is obtained, the optimization process is terminated and does not participate in the online control loop. Consequently, PSO introduces no computational burden during real-time DSP operation. The experimental implementation was executed with a sampling frequency of 10 kHz, corresponding to a sampling period of 100 μs. Even under the conservative execution-time estimation of 30–35 μs, the proposed controller utilizes less than 35% of the available sampling interval. Therefore, sufficient computational margin remains for ADC acquisition, PWM generation, communication services, protection routines, and interrupt handling. No timing violations or processor-overload conditions were observed during real-time experimental operation. Overall, the obtained results demonstrate that the proposed RBF–HONTSM–IKFAC control architecture achieves an effective balance between control performance, energy-efficiency enhancement, and computational cost. The low memory utilization, absence of online matrix operations, bounded computational complexity, and short execution time collectively confirm the suitability of the proposed method for real-time embedded implementation in industrial induction motor drive applications. This configuration ensures accurate performance evaluation while maintaining a practical real-time implementation environment consistent with industrial drive applications. Taken together, schematic of the coordinated dynamic performance and energy efficiency control strategy for induction motor drives based on hybrid intelligent control is illustrated in Fig. 3, the overallexperimental setup presented in Figs. 4a and b. The corresponding test bench, shown in Fig. 5. The proposed control strategy is experimentally validated in terms of both dynamic performance and energy efficiency optimization. The corresponding experimental results are presented in Figs. 6–21.Fig. 3Block diagram of the proposed hybrid optimization and control framework for energy-efficient and high-performance OC-based IM drives.Fig. 4(a) Implementation structure of the proposed control–optimization framework for induction motor. (b) Block diagram of the embedded DSP implementation of the proposed FOC scheme.Fig. 5Experimental test bench of the induction motor drive system.Fig. 6Dynamic preformance under variable speed, no load.Fig. 7Dynamic preformance under variable speed, rated load.Fig. 8The robust under variable resistance Rr = 1.5 Rr control.Fig. 9Robustness Evaluation Under Simultaneous Variations of Motor Parameters (Rs, Rr, and Lm Increased by 50%).Fig. 10The robust under radom load disturbance.Fig. 11High-speed operation Under 100% rated load conditions.Fig. 12High-speed operation under 50% rated load conditions.Fig. 13High-speed operation under 25% rated load conditions.Fig. 14Efficiency, Power Loss, and Energy Loss Comparison at 145 rad/s under different load conditions.Fig. 15Medium-speed operation under 100% rated load conditions.Fig. 16Medium-speed operation under 50% rated load conditions.Fig. 17Medium-speed operation under 25% rated load conditions.Fig. 18Efficiency, Power Loss, and Energy Loss Comparison at 95 rad/s under different load conditions.Fig. 19Low-speed operation under 100% rated load conditions.Fig. 20Low-speed operation under 50% rated load conditions.Fig. 21Low-speed operation under 25% rated load conditions. Block diagram of the proposed hybrid optimization and control framework for energy-efficient and high-performance OC-based IM drives. (a) Implementation structure of the proposed control–optimization framework for induction motor. (b) Block diagram of the embedded DSP implementation of the proposed FOC scheme. Experimental test bench of the induction motor drive system. Dynamic preformance under variable speed, no load. Dynamic preformance under variable speed, rated load. The robust under variable resistance Rr = 1.5 Rr control. Robustness Evaluation Under Simultaneous Variations of Motor Parameters (Rs, Rr, and Lm Increased by 50%). The robust under radom load disturbance. High-speed operation Under 100% rated load conditions. High-speed operation under 50% rated load conditions. High-speed operation under 25% rated load conditions. Efficiency, Power Loss, and Energy Loss Comparison at 145 rad/s under different load conditions. Medium-speed operation under 100% rated load conditions. Medium-speed operation under 50% rated load conditions. Medium-speed operation under 25% rated load conditions. Efficiency, Power Loss, and Energy Loss Comparison at 95 rad/s under different load conditions. Low-speed operation under 100% rated load conditions. Low-speed operation under 50% rated load conditions. Low-speed operation under 25% rated load conditions. Dynamic performance evaluation Figure 6 presents the dynamic performance of the investigated control strategies under variable-speed no-load operating conditions. The reference speed is sequentially varied from 0 to 145 rad/s, reduced to 50 rad/s, and subsequently increased to 125 rad/s in order to evaluate the transient tracking capability and current regulation performance of the drive system. The conventional PI-based FOC exhibits noticeable overshoot and oscillatory transient behavior during rapid speed transitions. During the acceleration process from 0 to 145 rad/s, the speed response reaches approximately 163 rad/s, corresponding to an overshoot of approximately 12.4%. Similarly, during the deceleration transition from 145 rad/s to 50 rad/s, the speed decreases to approximately 38 rad/s before converging to the reference value. These results indicate the limited capability of the PI controller to handle the nonlinear dynamics and coupling characteristics of the induction motor drive during transient operating conditions. In contrast, both the RBF–HONTSM and the proposed RBF–HONTSM–IKFAC strategies achieve nearly zero overshoot during the acceleration stage and exhibit only negligible undershoot during deceleration. The improved transient behavior is directly associated with the nonlinear terminal sliding surface and higher-order sliding dynamics of the HONTSM controller, which enforce fast convergence while suppressing excessive oscillations near the equilibrium point. In addition, the bounded adaptive compensation generated by the RBF network improves the capability of the controller to compensate lumped uncertainties and nonlinear disturbances during transient operating conditions. The enlarged transient responses further confirm that the PI controller introduces considerable oscillations immediately after the speed transitions, whereas the proposed nonlinear strategies maintain smooth and well-damped convergence characteristics. Among the investigated methods, the proposed RBF–HONTSM–IKFAC strategy provides the smoothest transient response. This behavior is attributed to the curvature-aware adaptive flux optimization mechanism, which continuously adjusts the excitation level according to the estimated curvature information of the loss function, thereby reducing unnecessary excitation dynamics during transient operationThe q-axis current isq, which is directly responsible for electromagnetic torque production, also exhibits noticeable differences among the considered control strategies. For the PI controller, isq presents larger transient spikes and oscillatory behavior during speed transitions, indicating less effective torque-current regulation. The RBF-HONTSM and proposed RBF-HONTSM-KFAC strategy achieve the smoothest and most stable isq dynamics, with reduced transient fluctuations and faster stabilization. This behavior indicates improved coordination between torque demand and current regulation, contributing to both enhanced dynamic performance and more efficient current utilization. A significant difference is also observed in the excitation current component. For both the PI and RBF–HONTSM controllers, the d-axis current isd remains approximately 0.8 A throughout the operating range. In contrast, the proposed RBF–HONTSM–IKFAC strategy reduces the excitation current to approximately 0.45 A while preserving stable speed tracking performance. This result directly confirms the effectiveness of the proposed curvature-aware flux optimization strategy. By adaptively reducing the magnetizing current under no-load operating conditions, the proposed method decreases unnecessary flux excitation and associated copper and core losses without degrading the dynamic characteristics of the drive system. Collectively, the experimental results demonstrate that the proposed hybrid intelligent control architecture effectively combines the finite-time convergence and robustness properties of HONTSM control, the adaptive nonlinear compensation capability of the RBF network, and the energy-aware flux adaptation mechanism of the IK FAC optimization strategy. Consequently, the proposed method achieves improved transient tracking performance, reduced overshoot, smoother current dynamics, and lower excitation current compared with the conventional PI-based FOC approach. Figure 7 illustrates the dynamic performance of the investigated control strategies under variable-speed rated-load operating conditions. The speed reference is sequentially varied among 145 rad/s, 125 rad/s, and 25 rad/s while the rated load torque is repeatedly applied and removed at each operating point. The corresponding quantitative performance indices are summarized in Table 4.Table 4Dynamic and Steady-State Performance Comparison of the Investigated Control Strategies.Control methodSettling Time (s)Peak Speed (rad/s)Overshoot (%)IAE(rad)ISE(rad2/s)RMSE (rad/s)Torque Ripple (%)THD current(%)PI2.59163.712.90.6930.1970.2225.65.45RBF HONTSM0.21145.280.1930.6160.1200.1746.26.99RBF HONTSM IKFAC0.15145.250.1730.2570.0260.0815.95.85 Table 4Dynamic and Steady-State Performance Comparison of the Investigated Control Strategies.Control methodSettling Time (s)Peak Speed (rad/s)Overshoot (%)IAE(rad)ISE(rad2/s)RMSE (rad/s)Torque Ripple (%)THD current(%)PI2.59163.712.90.6930.1970.2225.65.45RBF HONTSM0.21145.280.1930.6160.1200.1746.26.99RBF HONTSM IKFAC0.15145.250.1730.2570.0260.0815.95.85 Dynamic and Steady-State Performance Comparison of the Investigated Control Strategies. The conventional PI-based FOC exhibits the poorest dynamic performance among the investigated methods. As shown in Table 4, the settling time reaches 2.59 s, accompanied by a peak speed of 163.7 rad/s and an overshoot of 12.9%. Moreover, the PI controller yields the largest tracking-error indices, with IAE, ISE, and RMSE values of 0.693 rad, 0.197 rad2/s, and 0.222 rad/s, respectively. These results indicate limited disturbance-rejection capability and insufficient robustness against abrupt load variations over the investigated speed range. The RBF–HONTSM controller significantly improves the transient response owing to the combined action of adaptive nonlinear compensation and finite-time sliding-mode dynamics. The settling time is reduced from 2.59 s to 0.21 s, corresponding to a reduction of approximately 91.9%, while the overshoot decreases from 12.9% to only 0.193%. Furthermore, the RMSE is reduced to 0.174 rad/s, confirming the enhanced tracking accuracy achieved by the adaptive neural compensation and higher-order sliding-mode structure. The proposed RBF–HONTSM–IKFAC controller achieves the best overall performance. As reported in Table 4, the settling time is further reduced to 0.15 s, representing improvements of approximately 28.6% and 94.2% compared with the RBF–HONTSM and PI controllers, respectively. The overshoot remains extremely small at only 0.173%, while the peak speed is limited to 145.25 rad/s, indicating nearly perfect transient tracking. More importantly, the proposed controller achieves the lowest tracking-error indices, with IAE, ISE, and RMSE values of 0.257 rad, 0.026 rad2/s, and 0.081 rad/s, respectively. Compared with the PI controller, the RMSE is reduced by approximately 63.5%, demonstrating substantially improved speed-regulation accuracy under varying operating conditions. The current responses shown in Fig. 7 further validate the effectiveness of the proposed control strategy. Under the PI controller, the torque-producing current component exhibits pronounced transient peaks and oscillatory behavior during load application and removal, reflecting abrupt electromagnetic torque variations and increased dynamic stress on the drive system. In contrast, both nonlinear control strategies maintain considerably smoother current trajectories and smaller transient deviations, indicating improved torque regulation and enhanced disturbance rejection capability. A clear distinction is observed in the excitation-current component. For both the PI and RBF–HONTSM controllers, the excitation current remains nearly constant at approximately 0.8 A over the entire operating range. Conversely, the proposed RBF–HONTSM–IKFAC controller continuously adapts the excitation current according to the operating condition, reducing the excitation level whenever full magnetization is unnecessary. This behavior directly reflects the action of the proposed curvature-aware flux-optimization mechanism, which minimizes excessive magnetizing current while preserving dynamic performance and robustness against load disturbances. The steady-state performance metrics further support these observations. Although the RBF–HONTSM controller exhibits a slightly higher torque ripple (6.2%) and current THD (6.99%) than the PI controller, the proposed RBF–HONTSM–IKFAC strategy reduces these values to 5.9% and 5.85%, respectively. Consequently, the proposed controller achieves the best compromise between dynamic performance, tracking accuracy, disturbance rejection capability, and steady-state power quality. Observing the zoomed current components and electromagnetic torque responses, both the RBF–HONTSM and RBF–HONTSM–IKFAC strategies exhibit higher high-frequency current and torque ripple components than the conventional PI-based FOC strategy. This behavior is intrinsically associated with the switching characteristics of sliding-mode-based control. Although the higher-order nonsingular terminal sliding-mode structure substantially mitigates the severe chattering phenomenon typically encountered in conventional first-order SMC schemes, the discontinuous corrective action near the sliding manifold still introduces small high-frequency oscillatory components into the control signal. As a result, residual ripple components remain observable in the stator currents and electromagnetic torque responses. Nevertheless, this effect represents an acceptable engineering trade-off for the considerable improvement in robustness and disturbance rejection capability achieved by the proposed nonlinear control strategies. In particular, the higher-order sliding-mode dynamics enhance the controller’s ability to preserve accurate speed tracking and stable operation under abrupt load disturbances, parameter uncertainties, and noisy operating conditions, where the conventional PI controller exhibits larger speed deviations and weaker damping characteristics. Therefore, despite the slightly increased current and torque ripple, the proposed RBF–HONTSM and RBF–HONTSM–IKFAC strategies provide significantly improved robustness and operational reliability for high-performance induction motor drive applications. Figure 8 presents the robustness evaluation of the investigated control strategies under rotor resistance variation, where the rotor resistance is intentionally increased to Rr = 1.5Rr in order to assess the sensitivity of the drive system to parameter mismatch conditions. Since rotor resistance directly affects the rotor time constant and flux estimation accuracy in field-oriented control, its variation significantly influences the decoupling performance between torque and flux components, particularly during transient operating conditions and under loaded operation. The conventional PI-based FOC exhibits considerable performance degradation under the imposed parameter variation. During the startup transition from 0 to 125 rad/s, the speed response presents excessive oscillatory behavior and pronounced transient fluctuations before reaching the steady-state operating condition. Moreover, under rated-load operation between approximately 35 s and 55 s, the speed response exhibits continuous oscillations with relatively large amplitude, indicating reduced damping capability and deteriorated robustness caused by the rotor resistance mismatch. This behavior is mainly attributed to the sensitivity of the conventional PI controller to inaccurate flux orientation and parameter-dependent coupling dynamics, which become more pronounced when the rotor time constant deviates from its nominal value. In contrast, both the RBF–HONTSM and the proposed RBF–HONTSM–IKFAC strategies maintain stable speed tracking performance over the entire operating range despite the significant rotor resistance variation. The transient oscillations observed during startup are substantially reduced, and the steady-state speed responses remain significantly smoother under rated-load operation. The enlarged transient responses further confirm that the proposed nonlinear strategies effectively suppress excessive oscillatory behavior and maintain stable convergence characteristics under parameter uncertainty conditions. The current responses shown in Fig. 8 further demonstrate the influence of rotor resistance variation on the internal electromagnetic dynamics of the drive system. Under the PI controller, noticeable current ripple appears in the torque-producing current component during loaded operation, indicating increased electromagnetic torque oscillation and degraded current regulation performance caused by inaccurate flux estimation. By comparison, both proposed nonlinear strategies maintain significantly smoother current responses with reduced ripple amplitude throughout the entire operating range. This improvement is directly associated with the robustness of the higher-order sliding-mode dynamics and the bounded nonlinear compensation capability of the RBF network, which collectively improve disturbance rejection and reduce the sensitivity of the control system to parameter mismatch. Overall, the experimental results demonstrate that the proposed RBF–HONTSM–IKFAC strategy provides superior robustness against rotor resistance variation, improved transient damping capability, reduced speed and current oscillations, and enhanced current regulation performance compared with the conventional PI-based FOC approach. The obtained results also confirm the effectiveness of combining higher-order sliding-mode robustness, bounded adaptive RBF compensation, and curvature-aware flux adaptation for high-performance induction motor drives operating under parameter uncertainty conditions. To further evaluate the robustness of the investigated control strategies against severe modeling uncertainties, the controller parameters Rs, Rr, and Lm are simultaneously increased by 50% relative to their nominal values. Such a coupled-parameter mismatch simultaneously affects flux estimation accuracy, field orientation, and electromagnetic torque production, thereby representing a considerably more demanding robustness test than conventional single-parameter perturbations. As shown in Fig. 9, the performance of the conventional PI controller deteriorates significantly under the considered parameter mismatch condition. During startup from standstill to the rated operating speed of 149.2 rad/s, the speed response exhibits a large overshoot followed by persistent oscillations with a wide amplitude, indicating a strong dependence on accurate motor parameters and a degradation of the field-oriented decoupling mechanism. When the rated load is applied, noticeable speed oscillations appear around the reference value, revealing a reduced capability to reject the combined effects of load disturbances and parameter uncertainties. Moreover, the stator-current amplitude increases substantially and approaches its rated limit, indicating a higher control effort and increased copper losses required to maintain speed regulation under inaccurate model information. In contrast, the RBF–HONTSM controller preserves stable operation with negligible overshoot and significantly reduced speed fluctuations throughout the entire operating range. This demonstrates that the adaptive neural compensation and finite-time convergence properties of the HONTSM controller effectively mitigate the adverse effects of parameter mismatch and maintain accurate torque production despite modeling uncertainties. The proposed RBF–HONTSM–IKFAC controller exhibits robustness characteristics comparable to those of the baseline RBF–HONTSM strategy. No noticeable degradation in dynamic performance is observed after introducing the IKFAC-based excitation-current optimization layer. The speed response remains tightly regulated with very small steady-state fluctuations, while the excitation current is significantly reduced during light-load operation. These results confirm that the IKFAC optimization mechanism enhances energy efficiency without compromising the robustness, disturbance-rejection capability, or stability properties established by the underlying RBF–HONTSM control framework. Overall, Fig. 9 demonstrates that the proposed controller maintains satisfactory performance under severe coupled parameter uncertainties and provides a favorable balance between robustness, dynamic response, and energy efficiency, making it well suited for practical induction-motor-drive applications where parameter mismatch is unavoidable. In Fig. 10, the robustness of the proposed control strategy is evaluated under stochastic perturbations. The reference speed is creased stepwise from 0 to 25 rad/s to 75 rad/s at t = 25 s and t = 45 s , respectively, and further to 125 rad/s at t = 65 s, with a rated load torque is applied at t = 35 s and rejected at t = 75 s. Zero-mean Gaussian noise is injected into both current channels to emulate sensor uncertainty. For the conventional PI-based FOC, the influence of the injected measurement noise becomes considerably more pronounced after the rated load is applied. In particular, the speed response exhibits strong oscillatory behavior around the reference trajectory with relatively large amplitude and high-frequency fluctuations. The enlarged transient responses further show that the oscillation level significantly increases during loaded operation, indicating that the PI controller is highly sensitive to noisy current feedback under strong electromagnetic loading conditions. This behavior is mainly associated with the dependence of the PI-based FOC structure on accurate current and flux estimation. Under noisy measurement conditions, the corrupted feedback signals propagate through the decoupling and current regulation loops, leading to amplified torque ripple and oscillatory speed dynamics. By contrast, both the RBF–HONTSM and the proposed RBF–HONTSM–IKFAC strategies maintain significantly smoother speed responses throughout the entire operating process. The transient and steady-state responses before and after load application remain nearly unchanged, demonstrating strong robustness against measurement disturbance and noisy feedback conditions. Only minor localized perturbations are observed during load transitions, while the overall tracking performance remains stable and well damped. This behavior confirms the robustness of the higher-order sliding-mode dynamics against matched uncertainties and external perturbations. The current responses shown in Fig. 10 further support these observations. Under the PI controller, noticeable ripple appears in the torque-producing current component during loaded operation, reflecting the propagation of measurement noise into the electromagnetic torque dynamics. In contrast, both proposed nonlinear strategies maintain significantly smoother current responses with reduced ripple amplitude despite the injected random disturbances. The reduced current oscillation directly contributes to the improved speed regulation performance observed in the proposed control structures. A similar trend is observed in the excitation current component . For the PI and RBF–HONTSM strategies, the flux current remains approximately constant during operation, whereas the proposed RBF–HONTSM–IKFAC strategy adaptively adjusts the excitation level according to the operating condition while preserving stable current regulation under noisy measurement conditions. The excitation current trajectory remains smooth without introducing additional oscillatory behavior, indicating that the proposed curvature-aware flux optimization mechanism preserves numerical robustness even in the presence of stochastic measurement disturbances. Overall, the experimental results demonstrate that the proposed RBF–HONTSM–IKFAC strategy provides substantially improved robustness against measurement noise compared with the conventional PI-based FOC approach. The combination of higher-order sliding-mode robustness, bounded nonlinear RBF compensation, and adaptive flux optimization effectively suppresses disturbance propagation through the control loops, resulting in smoother speed regulation, reduced current ripple, and improved dynamic stability under noisy operating conditions. Evaluation of energy efficiency enhancement under varying operating conditions High-speed operation 145 rad/s under different load conditions (100%, 50%, and 25% rated torque) To comprehensively evaluate the effectiveness of the proposed optimization strategy, the energy efficiency performance is investigated under different loading conditions. Specifically, three operating scenarios are considered, corresponding to 100%, 50%, and 25% of the rated load torque, while the rotor speed is maintained at 145 rad/s, 95 rad/s and 55 rad/s. This setup allows for a systematic assessment of the controller performance over a wide load range, from rated to light-load conditions, where efficiency optimization becomes increasingly critical. The comparison focuses on steady-state efficiency, power loss, and accumulated energy loss, providing a comprehensive evaluation of energy utilization for the PI, RBF-HONTSM, and proposed RBF-HONTSM-KFAC. Figures 11, 12, 13, and 14 and Table 5 presents the energy-efficiency evaluation of the investigated control strategies at the high-speed operating condition of 145 rad/s under different load levels, including 100%, 50%, and 25% rated torque. The comparison focuses on efficiency, power loss, and accumulated energy loss in order to evaluate the capability of the proposed strategy to improve the energy utilization characteristics of the induction motor drive system. The experimental results indicate that the conventional PI-based FOC maintains moderate efficiency performance at rated load operation; however, its efficiency progressively deteriorates as the load torque decreases. This behavior is mainly associated with the fixed excitation current structure of the conventional FOC scheme, where the magnetizing current remains nearly constant regardless of the operating condition. Consequently, under light-load operation, unnecessary flux excitation increases copper and core losses, resulting in reduced overall energy efficiency.Table 5Efficiency, Power Loss, and Energy Loss Comparison at 145 rad/s Under Different Load Conditions.Torque (%)145 rad/sRBF-KFACPIRBFEfficiency(%)Power loss(W)Energy loss(J)Efficiency(%)Power loss(W)Energy loss(J)Efficiency(%)Power loss(W)Energy loss(J)10075.3347.472136.1573.951.232305.3570.4160.932741.855074.2525.141131.3070.130.921391.4065.1838.711741.952570.1315.44694.865.8518.8846.0052.8932.291453.05 Table 5Efficiency, Power Loss, and Energy Loss Comparison at 145 rad/s Under Different Load Conditions.Torque (%)145 rad/sRBF-KFACPIRBFEfficiency(%)Power loss(W)Energy loss(J)Efficiency(%)Power loss(W)Energy loss(J)Efficiency(%)Power loss(W)Energy loss(J)10075.3347.472136.1573.951.232305.3570.4160.932741.855074.2525.141131.3070.130.921391.4065.1838.711741.952570.1315.44694.865.8518.8846.0052.8932.291453.05 Efficiency, Power Loss, and Energy Loss Comparison at 145 rad/s Under Different Load Conditions. A similar trend is observed for the RBF–HONTSM strategy. Although the proposed nonlinear controller significantly improves transient tracking performance and disturbance rejection capability, the efficiency improvement remains limited because the excitation current level is not adaptively optimized according to the operating condition. As shown in the experimental responses, the excitation current component remains approximately constant over the entire operating range, leading to additional excitation-related power losses, particularly under reduced load conditions. Consequently, the RBF–HONTSM strategy exhibits lower efficiency than the conventional PI controller at several operating points despite its superior dynamic characteristics. This result confirms that improving dynamic performance alone does not necessarily guarantee improved energy efficiency in induction motor drives. By contrast, the proposed RBF–HONTSM–IKFAC strategy achieves the highest efficiency and the lowest power and energy losses over all investigated operating conditions. At 100% rated load, the proposed strategy improves the efficiency to approximately 75.33%, compared with 73.9% for the PI controller and 70.41% for the RBF–HONTSM strategy. More importantly, the superiority of the proposed approach becomes increasingly pronounced under partial-load operation. At 50% rated load, the efficiency increases to approximately 74.25%, while the PI and RBF–HONTSM strategies achieve only 70.1% and 65.18%, respectively. Under the 25% rated-load condition, the proposed strategy maintains an efficiency of approximately 70.13%, whereas the PI and RBF–HONTSM strategies decrease to approximately 65.85% and 52.89%, respectively. The power-loss and energy-loss results further confirm the effectiveness of the proposed energy optimization strategy. Under all investigated load conditions, the proposed RBF–HONTSM–IKFAC controller consistently achieves the lowest power loss and accumulated energy loss. In particular, under the 25% rated-load condition, the proposed strategy reduces the power loss to approximately 15.44 W, compared with 18.8 W for the PI controller and 32.29 W for the RBF–HONTSM strategy. Similarly, the accumulated energy loss is reduced to approximately 694.8 J, representing a substantial improvement over both comparative methods These results are in strong agreement with the theoretical analysis presented in "IK-FAC curvature-aware flux optimization for induction motor drives" section. According to the derived loss model, the total power loss is governed by the nonlinear trade-off between excitation-related losses and torque-producing copper losses. The proposed IK-FACcurvature-aware optimization mechanism continuously adjusts the flux-producing current reference according to the estimated local curvature information of the loss function, thereby driving the operating point toward the minimum-loss region without requiring explicit Hessian computation. As observed in the experimental current responses, the proposed strategy significantly reduces the excitation current component under reduced load conditions while preserving stable torque production. Consequently, unnecessary magnetizing current and associated copper and core losses are substantially reduced. Furthermore, unlike conventional first-order adaptive approaches, the proposed curvature-aware optimization mechanism provides smoother and more stable online flux adaptation by incorporating recursive curvature estimation into the update law. This behavior improves the convergence characteristics of the energy optimization process while preserving low computational complexity suitable for real-time DSP implementation.Overall, the experimental results demonstrate that the proposed RBF–HONTSM–IKFAC strategy successfully achieves simultaneous improvement of dynamic performance and energy efficiency. While the RBF–HONTSM controller primarily enhances transient robustness and disturbance rejection capability, the integration of the IK-FACcurvature-aware flux optimization mechanism enables substantial reduction of excitation-related losses and significant improvement of overall drive efficiency across a wide operating range. The experimental results further confirm the practical real-time feasibility of the proposed control framework. Despite integrating the RBF-based nonlinear controller, HONTSM dynamics, and IK-FAC optimization mechanism, the overall computational burden remains sufficiently low for embedded implementation because the proposed strategy mainly involves simple algebraic operations, Gaussian basis-function evaluations, and lightweight recursive scalar updates without requiring iterative optimization procedures, explicit Hessian computation, or matrix inversion. In addition, the RBF controller employs a compact network structure with a limited number of hidden neurons, thereby maintaining low computational overhead during online operation. Moreover, the PSO algorithm is only utilized offline for parameter tuning and therefore does not affect the online computational complexity during motor-drive operation. Consequently, the proposed framework preserves the conventional field-oriented control structure while remaining suitable for real-time DSP-based induction motor drive applications, as experimentally validated using the TMS320F28379D platform. Medium-speed operation 95 rad/s under different load conditions (100%, 50%, and 25% rated torque) Figures 15, 16, 17, and 18 and Table 6 present the energy-efficiency evaluation of the investigated control strategies at the medium-speed operating condition of 95 rad/s under variable rated-load conditions. Compared with the high-speed operating region, the influence of excitation-related losses becomes more dominant at medium speed, making the effectiveness of the proposed adaptive flux optimization mechanism more evident.Table 6Efficiency, Power Loss, and Energy Loss Comparison at 95 rad/s Under Different Load Conditions.Torque (%)95 rad/sRBF-KFACPIRBFEfficiency(%)Power loss(W)Energy loss(J)Efficiency(%)Power loss(W)Energy loss(J)Efficiency(%)Power loss(W)Energy loss(J)10068.6643.351950.7565.0151.132300.8561.2860.032701.355068.0922.241000.8060.3731.181403.1055.5937.941707.302567.8711.24505.855.6318.94852.3049.7424.011080.45 Table 6Efficiency, Power Loss, and Energy Loss Comparison at 95 rad/s Under Different Load Conditions.Torque (%)95 rad/sRBF-KFACPIRBFEfficiency(%)Power loss(W)Energy loss(J)Efficiency(%)Power loss(W)Energy loss(J)Efficiency(%)Power loss(W)Energy loss(J)10068.6643.351950.7565.0151.132300.8561.2860.032701.355068.0922.241000.8060.3731.181403.1055.5937.941707.302567.8711.24505.855.6318.94852.3049.7424.011080.45 Efficiency, Power Loss, and Energy Loss Comparison at 95 rad/s Under Different Load Conditions. The experimental results show that the conventional PI-based FOC experiences a progressive reduction in efficiency as the load torque decreases. Although the PI controller maintains acceptable performance at rated-load operation, the fixed excitation structure leads to unnecessary magnetizing current under partial-load conditions, which increases both copper and core losses. Consequently, the efficiency decreases from approximately 65.01% at rated load to 55.63% under the 25% rated-load condition. A similar behavior is observed for the RBF–HONTSM strategy. Despite its superior dynamic robustness and smoother transient responses demonstrated in the previous subsection, the efficiency performance remains inferior to the PI controller over the entire operating range. In particular, the efficiency decreases to approximately 49.74% under the 25% rated-load condition, accompanied by a power loss of approximately 24.01 W and an accumulated energy loss exceeding 1080 J. This behavior indicates that the improvement of dynamic regulation alone is insufficient to guarantee high energy-utilization performance when the excitation level is not simultaneously optimized. The larger excitation-related losses observed in the RBF–HONTSM strategy are mainly associated with the persistently high magnetizing current required to preserve robust nonlinear regulation under varying operating conditions. In contrast, the proposed RBF–HONTSM–IKFAC strategy consistently achieves the highest efficiency and the lowest energy dissipation across all investigated operating conditions. At rated load, the proposed strategy improves the efficiency to approximately 68.66%, while simultaneously reducing the power loss to approximately 43.35 W. More importantly, the superiority of the proposed approach becomes increasingly pronounced under partial-load operation. At 50% rated load, the efficiency reaches approximately 68.09%, representing an improvement of approximately 7.7% and 12.5% compared with the PI and RBF–HONTSM strategies, respectively. Under the 25% rated-load condition, the proposed method maintains an efficiency of approximately 67.87%, whereas the PI and RBF–HONTSM strategies decrease significantly to 55.63% and 49.74%, respectively. The power-loss and accumulated energy-loss results further confirm the effectiveness of the proposed optimization mechanism. Under the 25% rated-load condition, the proposed method reduces the power loss to approximately 11.24 W, corresponding to reductions of approximately 40.5% and 53.2% compared with the PI and RBF–HONTSM strategies, respectively. Similarly, the accumulated energy loss decreases to approximately 505.8 J, which is substantially lower than the comparative approaches. These results directly validate the theoretical foundation established in "IK-FAC curvature-aware flux optimization for induction motor drives" section. Under medium-speed and light-load conditions, the imbalance between excitation and torque-producing losses becomes more pronounced. Since the conventional PI and RBF–HONTSM strategies maintain nearly constant excitation current levels, the drive operates away from the optimal loss-minimization region. In contrast, the proposed curvature-aware optimization continuously adjusts the flux-producing current reference using local curvature information of the nonlinear loss function, thereby driving the operating point toward the minimum-loss region in real time. The current responses further confirm this behavior. Unlike the PI and RBF–HONTSM strategies, where the excitation current remains nearly constant, the proposed RBF–HONTSM–IKFAC strategy effectively reduces the magnetizing current during partial-load operation while preserving stable torque production and accurate speed regulation. This adaptive excitation management directly reduces copper and core losses, leading to the experimentally observed efficiency improvement.Another important observation is that the proposed energy optimization mechanism does not compromise the robustness characteristics achieved by the HONTSM-based nonlinear control structure. The speed responses remain smooth and well regulated throughout the operating process, while the current dynamics preserve low ripple and stable behavior despite the continuous online adaptation of the excitation level. This characteristic confirms that the proposed strategy successfully achieves coordinated enhancement of both dynamic regulation performance and energy efficiency within a unified control framework. Overall, the experimental results obtained at the medium-speed operating region demonstrate that the proposed RBF–HONTSM–IKFAC strategy provides a substantially improved balance between robust nonlinear control performance and energy-efficient operation. The integration of the IK-FACcurvature-aware flux optimization mechanism enables the drive system to operate significantly closer to the optimal efficiency trajectory over a wide range of loading conditions while preserving the robustness and finite-time convergence properties of the underlying HONTSM control structure. Low speed operation 55 rad/s under different load conditions (100%, 50%, and 25% rated torque) Figures 19, 20 and 21 and Table 7 present the energy-efficiency evaluation of the investigated control strategies at the low-speed operating condition of 55 rad/s under variable load conditions. Compared with the medium and high-speed operating regions, the low-speed region represents a more challenging operating condition for energy-efficient control because the electromagnetic torque must be maintained under reduced back-EMF conditions while excitation-related losses become increasingly dominant relative to the mechanical output power.Table 7Efficiency, Power Loss, and Energy Loss Comparison at 55 rad/s Under Different Load Conditions.Torque (%) 55 rad/sRBF-KFACPIRBFEfficiency (%)Power loss (W)Energy loss (J)Efficiency (%)Power loss (W)Energy loss (J)Efficiency (%)Power loss (W)Energy loss (J)10057.0941.331859.8551.1252.612367.454762.022790.905056.8520.86938.745.8732.441459.8041.3139.001755.002556.0310.79485.5541.3319.52878.4035.8924.541104.30 Table 7Efficiency, Power Loss, and Energy Loss Comparison at 55 rad/s Under Different Load Conditions.Torque (%) 55 rad/sRBF-KFACPIRBFEfficiency (%)Power loss (W)Energy loss (J)Efficiency (%)Power loss (W)Energy loss (J)Efficiency (%)Power loss (W)Energy loss (J)10057.0941.331859.8551.1252.612367.454762.022790.905056.8520.86938.745.8732.441459.8041.3139.001755.002556.0310.79485.5541.3319.52878.4035.8924.541104.30 Efficiency, Power Loss, and Energy Loss Comparison at 55 rad/s Under Different Load Conditions. The experimental results reveal a substantial degradation in the energy-utilization capability of the conventional PI-based FOC at low-speed operation. Although the drive system preserves stable speed regulation, the efficiency decreases significantly as the operating load is reduced. In particular, the efficiency decreases from approximately 51.12% at rated load to only 41.33% under the 25% rated-load condition. Simultaneously, the accumulated energy loss remains relatively high across all operating conditions, indicating that the fixed excitation structure becomes increasingly inefficient in the low-speed region. The RBF–HONTSM strategy exhibits a similar tendency. Despite providing improved dynamic robustness and smoother transient responses compared with the PI controller, the efficiency performance remains limited because the excitation current is not adaptively optimized according to the operating condition. As observed in the experimental current responses, the magnetizing current remains nearly constant even under reduced load conditions, resulting in excessive excitation-related losses. Consequently, the RBF–HONTSM strategy achieves only 35.89% efficiency under the 25% rated-load condition, accompanied by a power loss of approximately 24.54 W and an accumulated energy loss exceeding 1100 J. These results further confirm that robust nonlinear regulation alone is insufficient to ensure efficient energy utilization when the flux level is maintained unnecessarily high during light-load operation. In contrast, the RBF–HONTSM–IKFAC strategy maintains significantly higher efficiency over the entire low-speed operating range. At rated-load operation, the proposed method achieves approximately 57.09% efficiency, representing noticeable improvements compared with both the PI and RBF–HONTSM strategies. More importantly, the superiority of the proposed approach becomes increasingly evident as the load torque decreases. Under the 50% rated-load condition, the proposed strategy achieves approximately 56.85% efficiency, while the PI and RBF–HONTSM strategies achieve only 45.87% and 41.31%, respectively. Under the 25% rated-load condition, the proposed method maintains approximately 56.03% efficiency, whereas the comparative methods experience severe efficiency degradation. Observing the current components and torque, it is easy to see that both the RBF–HONTSM and RBF–HONTSM–IKFAC strategies exhibit higher high-frequency current and electromagnetic torque ripple components than the conventional PI-based FOC. This behavior is consistent with the previously discussed characteristics of higher-order sliding-mode dynamics, where slight residual ripple may appear due to the discontinuous corrective action around the sliding manifold. Nevertheless, this trade-off remains acceptable considering the substantial improvement in robustness and disturbance rejection capability achieved by the proposed nonlinear control strategies. As demonstrated in Fig. 7, both controllers maintain stable operation and accurate speed tracking under rapid speed variations and abrupt load disturbances. Similarly, under parameter uncertainty conditions in Fig. 8 and noisy measurement environments in Fig. 10, the proposed strategies preserve significantly smoother and more stable system responses than the conventional PI-based approach. Among the investigated methods, the proposed RBF–HONTSM–IKFAC strategy demonstrates the most balanced overall performance by simultaneously achieving high dynamic accuracy, strong robustness, and improved energy efficiency. In contrast, although the RBF–HONTSM controller provides excellent transient regulation and disturbance rejection capability, its relatively high excitation-current level leads to increased energy consumption and larger power losses during operation. Therefore, the integration of the IKFAC-based curvature-aware flux optimization mechanism enables the proposed strategy to overcome the conventional robustness–energy efficiency trade-off commonly observed in nonlinear sliding-mode-based induction motor drive systems. Conclusion This paper has presented a hybrid intelligent control strategy for high-performance induction motor drives under field-oriented control. The proposed method integrates an RBF neural network, HONTSM control, and an improved IK-FAC flux optimization strategy to simultaneously enhance dynamic performance, robustness, and energy efficiency. In the proposed architecture, the RBF network generates the torque-producing current reference, while the HONTSM controller improves disturbance rejection capability, tracking accuracy, and robustness against parameter uncertainties and external disturbances. In addition, the proposed IK-FAC optimization strategy adaptively optimizes the flux-producing current reference in real time using recursive curvature estimation without requiring explicit Hessian computation or matrix inversion, thereby preserving low computational complexity suitable for embedded DSP implementation. The effectiveness of the proposed control framework has been experimentally validated on a Texas Instruments TMS320F28379D digital signal processor under various operating conditions. The obtained results demonstrate improved tracking performance, fast transient response, reduced chattering, enhanced disturbance rejection capability, and improved energy efficiency compared with conventional approaches. Future work will focus on extending the proposed curvature-aware optimization framework to electric vehicle traction systems and adaptive multi-objective energy management strategies under wider operating conditions and parameter variations.