First-principles study of novel Cs3SCl anti-perovskite and performance assessment of solar cell structures with different hole transport layers and back contact metals Authors: Md. Earshad Ali, Anis Attour, Md. Nobiul Islam, Karim Kriaa, Md. Azizur Rahman, S. AlFaify, Noureddine Elboughdiri Published: 2026 ABSTRACT Anti-perovskite materials have recently gained special importance for environmentally friendly, lead-free, and low-cost renewable energy technologies. In this study, the structural, electronic, dynamic, thermodynamic, mechanical, optical, and photovoltaic properties of Cs3SCl anti-perovskite are analyzed in detail by density functional theory (DFT) and an SCAPS-1D simulator. The results show that Cs3SCl is thermodynamically, dynamically, and mechanically stable, with a ductile nature due to its B/G ratio of 2.03. The electronic band structure analysis identified the compound as a direct bandgap semiconductor, with bandgaps of 1.185 eV and 2.051 eV obtained by GGA-PBE and HSE06 methods, respectively. This suitable bandgap is highly favorable for visible light absorption. Optical analysis shows that Cs3SCl exhibits high absorption coefficients of about (2.6–0.2) × 105 cm−1 in the ultraviolet, visible, and near-infrared regions. In addition, its favorable refraction, low reflectivity, and excellent dielectric properties further strengthen its potential for solar energy harvesting, charge-carrier generation, and optoelectronic applications. A fully lead-free Al/FTO/SnS2/Cs3SCl/HTL/Se solar cell was designed and optimized to evaluate the photovoltaic potential of the material. After systematic optimization of the hole transport layer (HTL), back-contact metal, device temperature, absorber layer thickness, defect density, and shallow acceptor density, the Cu2Te-based device exhibited the highest performance. At a 0.750 µm absorber layer thickness, 1 × 1015 cm−3 defect density, and 1 × 1017 cm−3 shallow acceptor density, the device achieves an open-circuit voltage of 0.752 V, a short-circuit current density of 39.23 mA cm−2, a fill factor of 84.43%, and a power conversion efficiency of 24.92%. Overall, these results indicate that Cs3SCl is a highly promising material for future generations of high-efficiency, environmentally friendly solar cells, visible-light-dependent photocatalytic technologies, and advanced optoelectronic devices. Introduction The current global energy crisis, the rapidly growing demand for semiconductor materials in modern optoelectronic technologies, and the increasing pressure of environmental risks have made the search for sustainable and renewable energy sources more urgent than ever before. The development of new materials with advanced properties for future generations of electronic and energy-intensive devices is currently considered one of the main goals of modern scientific research.1,2 In this context, the main objective of this research is to increase the efficiency of renewable energy production. In recent years, perovskite materials have revolutionized photocatalysis and photovoltaic technologies.3–5 The addition of these components has significantly improved the overall performance of the respective devices.6 Notably, the power conversion efficiency of perovskite solar cells increased from 3.8% to approximately 26.7% between 2009 and 2024, clearly demonstrating the extraordinary potential of this material class.6–9 In 2025, Md. E. Ali reported the first design and performance evaluation of an Al/FTO/SnS2/Na3SBr/CuO/Au anti-perovskite solar cell (APSC) employing Na3SBr as the absorber material. Using the SCAPS-1D simulation platform, the proposed device demonstrated an impressive power conversion efficiency (PCE) of 27.172%.1 Additionally, in 2019, a conversion efficiency of about 17% was achieved in hydrogen production from solar energy using a MAP(I0.85Br0.15)3/Si-based structure, further strengthening the multifaceted potential of perovskite-based energy technologies.10 Recent studies on functional and energy-based materials have shown that defect engineering, compositional tuning, interface optimization, and crystal-structure regulation play important roles in improving the overall performance of devices.11–13 Defect passivation techniques have been shown to increase the operational stability of semiconductor devices by reducing carrier trapping and recombination.11 Similarly, theoretical studies have shown that the electronic structure, optical response, and charge-transport properties of materials can be effectively controlled through doping and compositional modification.12,13 On the other hand, recent studies based on energy conversion and energy storage technologies have further highlighted the importance of efficient ion transport, interfacial stability, and charge-transfer processes.14–16 In addition, crystal-structure repair, surface-energy homogenization, and crystal-facet engineering have emerged as effective strategies to enhance the long-term stability and performance of materials.15,17 At the same time, numerical reliability optimization has been established as an important method for evaluating the reliability and predicting the performance of advanced electronic devices.18 Also, selenium doping significantly modifies the electronic structure of ZrO2 by reducing the bandgap and enhancing optical properties such as dielectric response and absorption, demonstrating its potential for improved optoelectronic applications.19 These advances collectively indicate that integrated analysis of their structural, electronic, optical, and transport properties is crucial for the design of next-generation energy-based materials. Although perovskite-based solar cells and photocatalytic materials have shown significant progress, several fundamental problems remain in the industrialization of these technologies. In particular, the lack of long-term stability, rapid performance degradation upon exposure to light and air, and the toxic nature of some of the materials used have limited the commercial application of this technology. Due to these limitations, the search for alternative and more stable materials has now become an important area of research. In recent studies, materials with anti-perovskite structures have attracted much attention from researchers.1,20–23 Anti-perovskite is essentially a cubic crystal structure, where the conventional ABX3 perovskite structure is inverted to form X3BA. Here X acts as a one-dimensional positive ion (A+), B as a two-dimensional negative ion (B2−), and A as a one-dimensional negative ion (X−).7,24–27 Such materials are naturally occurring on Earth, are generally non-toxic, and exhibit bandgaps suitable for solar cells.28–31 Various studies have proven that anti-perovskite materials hold tremendous potential in many areas of modern technology. These include optoelectronic devices, solar energy conversion systems, switching memory devices, energy storage device, superconductors, hydrogen storage systems, and high-efficiency photocatalysis.32–36 Overall, existing research results indicate that anti-perovskite materials have enormous potential for use in future generation energy and optoelectronic technologies due to their environmental friendliness, structural stability, and high performance.1,2,20,21,28 However, extensive studies have already been conducted on the water-splitting efficiency of Na3SI-based Al/Na3SI/Se composites, which provide important insights into light-induced photocatalytic performance.2 Similarly, hydride-type anti-perovskite compounds such as K3SH, K3SeH, and K3TeH are capable of storing 3.24, 2.49, and 2.008 wt% hydrogen, respectively, and can release hydrogen in the temperature range of 672 K to 964 K, which identifies them as potential hydrogen storage materials.35 On the other hand, a thin-film all-solid-state battery (ASSB) device with a LiCoO2/Li3OCl/graphite structure fabricated using layer-by-layer technology exhibited a discharge capacity of 120 mA h g−1 in the voltage range of 2.2–4.2 V, indicating another important potential of anti-perovskite materials in energy storage technology.37,38 The photocatalytic efficiency of Co3ZnN anti-perovskite under visible light was found to be about six times higher than that of conventional materials, indicating its high light-sensitive response.39 Theoretical analysis also showed that the hydrogen evolution reaction (HER) performance of Ni3InN compounds can be significantly improved by controlling strain and applying appropriate doping.40 In addition, recent studies have shown that Ca6BiSbN2 and Sr6BiSbN2, among the X6BiSbN2 (X = Mg, Ca, Sr) type double anti-perovskite materials, are suitable as absorber layers in solar cells and also have potential for optoelectronic and thermoelectric applications.41 Also, a 2025 study showed that Ni3AC (A = Mg, Zn, Cd) anti-perovskite compounds behave as Ni3MgC-type superconductors, and their superconducting transition temperature was determined to be around 8.644 K.42 In 2024, p-type doping of Sr3BiN and Mg3BiN compounds achieved the highest ZT values of 1.49 and 1.18 at 900 K, respectively, making them highly promising for future thermoelectric technologies.43 This study proposes an environmentally friendly and lead-free Cs3SCl anti-perovskite compound as a potential absorber material for next-generation solar energy and optoelectronic technologies. Being composed of relatively safe elements such as cesium, sulfur, and chlorine, it can be considered a viable alternative to conventional toxic perovskite materials. Although there has been extensive research on various materials in the anti-perovskite class, to the best of our knowledge, integrated photovoltaic analysis based on density functional theory (DFT) and SCAPS-1D on Cs3SCl has not been previously reported. Therefore, it is scientifically crucial to evaluate its fundamental properties and applicability in solar cells. Generally, such anti-perovskite compounds have a cubic crystal structure and crystallize under the Pm3̄m space group, which is presented in Fig. 1(a).6,7 In this study, the structural, thermodynamic, dynamic, mechanical, electronic, and optical properties of Cs3SCl have been systematically analyzed using DFT methods. The results obtained indicate the high stability, suitable direct bandgap, and strong light-absorption ability of the compound, which are essential for efficient solar energy harvesting. At the same time, a completely lead-free Al/FTO/SnS2/Cs3SCl/HTL/Se solar cell structure has been designed and optimized using SCAPS-1D to verify its real photovoltaic potential. The optimal structure has been determined by analyzing various hole transport layers (HTLs), back-contact metal, device temperature, absorber layer thickness, defect density, and shallow acceptor density. The optimized Al/FTO/SnS2/Cs3SCl/Cu2Te/Se device achieved a power conversion efficiency of 24.92%, which clearly demonstrates the high photovoltaic potential of this material. Overall, the research results establish Cs3SCl as a highly promising material for environmentally friendly, sustainable, and high-efficiency solar energy and optoelectronic technologies. (a) Optimized cubic crystal structure of the Cs3SCl anti-perovskite obtained from DFT calculations, showing the atomic arrangement of Cs, S, and Cl atoms. (b) The corresponding Brillouin zone with the selected high-symmetry k-point path used for electronic band structure calculations. Simulation methodology First-principles DFT-based computational methods of Cs3SCl anti-perovskite In this research, the structural stability, dynamic and thermodynamic behavior, mechanical elasticity, electrical response, and optical properties of the inorganic cubic 3D bulk anti-perovskite compound Cs3SCl have been analyzed in detail using first-principles Density Functional Theory (DFT) methods. All computational simulations were conducted using the widely used and reliable Quantum ESPRESSO software package, which is known for its high accuracy in structural, thermal, phonon-based stability, elastic properties, and optoelectronic analysis.1,44–46 This study uses scalar-relativistic Norm-Conserving (NC) pseudopotentials (Cs.pbe-sp-hgh.UPF, S.pbe-hgh.UPF, and Cl.pbe-hgh.UPF), which provide high numerical accuracy and results while maintaining computational efficiency.2,47 The Perdew–Burke–Ernzerhof (PBE) functional, belonging to the generalized gradient approximation (GGA) class, has been applied to consider exchange-correlation effects,6,48 which provides more realistic results than the Local Density Approximation (LDA) for crystal structures.7,49 Extensive convergence tests have been performed on all important parameters to ensure the accuracy of the calculations. The analysis of the effect on total energy in the plane-wave-based calculations, as shown in Fig. 2(a), indicates that the energy converges correctly at ecutwfc = 50 Ry and ecutrho = 300 Ry. However, for more accurate results, ecutwfc = 60 Ry and ecutrho = 360 Ry were adopted in all final calculations.20,50 Similarly, to verify Brillouin zone sampling, Γ-centered Monkhorst–Pack k-point meshes from 1 × 1 × 1 to 9 × 9 × 9 were tested. Although the energy remains stable on a 4 × 4 × 4 mesh, the result is illustrated in Fig. 2(b). Furthermore, a 6 × 6 × 6 Γ-centered k-point grid is used in all calculations for greater reliability. A strong convergence threshold of 1 × 10−6 Ry has been set to maintain high accuracy in electronic self-consistent field (SCF) calculations.21,51,52 All these convergence tests confirm that the computational setup used makes the research results reliable and numerically stable. However, for more accurate prediction of the bandgap, the HSE06 hybrid functional has been applied. In this case, a 6 × 6 × 6 Γ-centered k-point grid and an equal density 6 × 6 × 6 q-point mesh have been used for Brillouin zone sampling, which ensures the accuracy of the hybrid functional calculations.28,53 In addition, a 10 × 10 × 10 Γ-centered k-point mesh has been adopted to more accurately analyze the optical properties.28,54–56 Additionally, the electrostatic potential of the proposed anti-perovskite compound has been analyzed. Since no surface or vacuum is naturally present in a three-dimensional bulk system, for this purpose, the cubic bulk structure of Cs3SCl is first transformed into a (1 1 2) supercell and then constructed into a slab shape along the (0 0 1) direction. A vacuum layer of about 25 Å thickness is added along the Z-axis of the slab. It is noteworthy that this slab model was used only for electrostatic potential calculations and was not applied to structural optimization or other numerical analyses.1,57–60 All pseudopotential files used in this study were collected from official sources of Quantum ESPRESSO, specifically from PSlibrary and the Hartwigsen–Goedecker–Hutter (HGH) pseudopotential dataset. Convergence and stability analysis of Cs3SCl anti-perovskite: (a) plane-wave cutoff energy convergence, (b) k-point mesh convergence, (c) structural optimization through lattice-parameter variation, and (d) phonon dispersion characteristics. Computational methods for solar cell device design and performance analysis using Cs3SCl anti-perovskite This study uses the widely used SCAPS-1D (version 3.3.09) solar cell simulation software, developed by Professor Marc Burgelman, to analyze the design and performance of Cs3SCl-based anti-perovskite solar cells.1,61–64 SCAPS-1D was selected as suitable for this work due to its high consistency with previously published research and strong device modeling capabilities.7,65–67 The SCAPS-1D software is capable of building solar cell structures consisting of up to seven different layers, where each layer can be defined as n-type, p-type, or intrinsic. The physical behavior of the device is primarily determined by three fundamental equations: Poisson's equation, the carrier transport equation, and the continuity equation. These equations collectively determine the charge carrier transport, generation and recombination processes, and the distribution of the internal electric field. In this study, a single-absorber anti-perovskite solar cell (APSC) structure has been designed, where Cs3SCl is used as the main absorber layer.21,65–68 The main objective of this proposed device design is to develop lead-free solar cells and analyze the device performance using various potential hole transport layers (HTL). The final proposed solar cell structure is Al/FTO/SnS2/Cs3SCl/HTL/Se. In this structure, Cs3SCl acts as the active light-absorbing layer. Aluminum (Al, 4.1 eV)1,2,69 is used as the front contact due to its relatively low work function, which facilitates efficient electron collection from the FTO/ETL side and minimizes contact resistance. On the other hand, selenium (Se, 5.9 eV)20,28,70 is employed as the back contact material after evaluating several candidate metals, where Se provided the most favorable energy alignment with the HTL, leading to improved hole extraction and overall device performance. During device simulation, CuO, Sb2S3, Zn3P2, and Cu2Te were used separately as HTLs, while SnS2 was kept fixed as the electron transport layer (ETL). All other layer parameters were kept unchanged except for the change in HTL so that the actual impact of HTL can be accurately analyzed. All simulations were conducted at a temperature of 300 K, a frequency of 1 × 106 Hz, and under standard AM 1.5 G solar radiation.21,65–68 The absorber layer thickness, defect density, shallow acceptor concentration, effective device temperature, and back-contact metal have been optimized in stages to achieve maximum efficiency. Two important interface layers, SnS2/Cs3SCl and Cs3SCl/HTL, are included in the model to ensure realistic device behavior. These interfaces reduce charge recombination, strengthen the internal electric field, and improve the overall chemical and electrical stability of the device.21,65–68 Result and discussion Structural characteristics of Cs3SCl anti-perovskite The optimized crystal structure of the Cs3SCl compound is shown in Fig. 1(a), which adopts a cubic anti-perovskite configuration with the high-symmetry Pm3̄m space group. The unit cell consists of five atoms, where Cs atoms occupy the face-centered positions [(0.5, 0, 0), (0, 0.5, 0), and (0, 0, 0.5)], the S atom is located at the cube corner (0, 0, 0), and the Cl atom resides at the body-centered position (0.5, 0.5, 0.5). This atomic arrangement confirms the typical anti-perovskite framework and ensures structural symmetry and stability. The corresponding Brillouin zone and high-symmetry k-path (Γ–X–M–Γ–R–X) used for electronic structure calculations are illustrated in Fig. 1(b), which is appropriate for cubic systems. The structural optimization was performed by minimizing the total energy as a function of lattice constant, as shown in Fig. 2(c). The equilibrium lattice constant is obtained at the minimum energy point, indicating the most stable configuration. The optimized lattice parameter (ao = 6.617 Å), unit cell volume (Vo = 1955.75 (bohr)3), and total energy (Eo = −171.80103 Ry) are listed in Table 1. The obtained lattice constant is consistent with related anti-perovskite compounds such as Cs3SBr, confirming the reliability of the present calculations. Additionally, convergence tests with respect to k-point sampling and cutoff energy were carefully performed to ensure numerical accuracy. Table 1Comparative validation of the Cs3SCl anti-perovskite using lattice parameter, total energy, and cell volumeCompound a 0 (Å) (a = b = c)Unit cell-volume Vo (bohr)3Total energy E0 (Ry)ReferenceCs3SCl6.6171955.75−171.80103This workNa3OI4.7337715.86−357.11847 6 Na3OBr4.6120662.0516−622.75546 7 Na3SBr5.2576980.80−611.34799 1 K3SeBr6.20481612.1492−734.150703 28 K3SeI6.23651637.024−211.7811 20 Cs3SBr6.65461988.77−482.56866 21 Comparative validation of the Cs3SCl anti-perovskite using lattice parameter, total energy, and cell volume Phonon features of Cs3SCl anti-perovskite Fig. 2(d) presents the phonon dispersion spectrum of the Cs3SCl anti-perovskite compound, which provides insight into the lattice vibrational properties and dynamical stability of the material. Phonon dispersion analysis is a well-established method for evaluating lattice stability, as it reflects the collective atomic vibrations within the crystal.7,21,71,72 In this study, the phonon properties of Cs3SCl were calculated based on the fully optimized lattice parameters and atomic positions along the high-symmetry path Γ–X–M–Γ–R–X. The obtained phonon spectrum exhibits well-defined acoustic and optical branches throughout the Brillouin zone.21,73–75 Notably, no imaginary (negative) phonon frequencies are observed, confirming the dynamical stability of the Cs3SCl structure. In addition, the acoustic branches smoothly approach zero frequency near the Γ-point, indicating proper long-wavelength vibrational behavior. These results confirm that the optimized structure is dynamically stable and suitable for further electronic and optical investigations. Mechanical features of Cs3SCl anti-perovskite Understanding the elastic properties of any solid material is crucial, as they govern the material's structural stability, response to external stresses, and performance in various technological applications.7,21,76 Specifically, the thermo_pw module, along with computational tools like Quantum ESPRESSO, calculates elastic constants and gives detailed information about how stiff, ductile, and resistant to deformation materials are on a small scale. This information is important not only for understanding the fundamental scientific behavior of the material but also for guiding the design of photocatalysis, photovoltaic, and optoelectronic devices. In the present study, we determined the elastic constant of Cs3SCl anti-perovskite to obtain a clear picture of its mechanical properties. Key mechanical properties such as Bulk modulus, Young's modulus, Poisson's ratio, and overall deformation resistance have been determined. The values obtained using specific eqn (1)–(14) (ref. 1, 2, 7 and 21) and numerical methods are compiled in Table 2, which provides comprehensive and well-organized information on the elastic response of the material.1Mechanical stability criteria (Born criteria; cubic crystal): C11 − C12 > 0, C11 + 2C12 > 0, and C44 > 0 Table 2Elastic properties and mechanical stability of the Cs3SCl anti-perovskiteMechanical/elastic parametersMechanical/elastic parameters valueElastic constant C1123.538 GPaElastic constant C121.146 GPaElastic constant C441.910 GPaC11 − C12, C11 + 2C12, and C4422.392, 25.83, and 1.91 (GPa) which > 0, stableBulk modulus, B8.61 GPaShear modulus for Voigt approximation, Gv5.624 GPaShear modulus for Reuss approximation, GR2.859 GPaShear modulus for Voigt–Reuss–Hill average, G4.241 GPaYoung's modulus, E10.789 GPaPoisson's ratio, V0.272Pugh's ratio, (B/G)2.03Cauchy pressure, CP−0.764 GPaZener anisotrop factor, A0.171Universal aniostropy index, AU4.835Shear sound velocity, VS1262.12 ms−1Longitudinal sound velocity, VL2314.65 ms−1Average Debye sound velocity, Vm1281.3 ms−1Debye temperature, ϴD98.468 K Elastic properties and mechanical stability of the Cs3SCl anti-perovskite Bulk modulus:2 Shear modulus (G): For Voigt approximation:3 For Reuss approximation:4 For Voigt–Reuss–Hill average:5 Young's modulus:6 Poisson's ratio:7 Ductility vs. Brittleness (Pugh's ratio):8B/G > 1.75; ductile and if B/G < 1.75; brittle Cauchy pressure (bound nature):9CP = C12 − C44; If CP > 0, metallic, and CP < 0; covalent/directional bonding tendency Elastic anisotropy: Zener anisotrop:and Universal aniostropy index:10 Sound velocity & Debye temperature: Shear sound velocity:11 Longitudinal sound velocity:12 Average sound velocity:13Debye temperature:14Here, h & KB = planck & Boltzman constant, n = atom number per unit cell, V = unit cell volume, and ρ = density.1,2,7,21 Table 2 presents the calculated elastic and mechanical properties of the Cs3SCl anti-perovskite compound. For a cubic crystal, mechanical stability is confirmed by the Born stability criteria: C11 − C12 > 0, C11 + 2C12 > 0, and C44 > 0. The obtained values (22.392 GPa, 25.83 GPa, and 1.91 GPa, respectively) satisfy these conditions, confirming the mechanical stability of the Cs3SCl structure. The calculated bulk modulus (B = 8.61 GPa) indicates that the material is relatively compressible, while the shear modulus (G = 4.241 GPa) and Young's modulus (E = 10.789 GPa) suggest low resistance to shear and elastic deformation. The Poisson's ratio (ν = 0.272) lies within the typical range for ionic materials, indicating central interatomic forces. The Pugh's ratio (B/G = 2.03) is greater than 1.75, suggesting ductile behavior of the material. However, the negative Cauchy pressure (−0.764 GPa) indicates a certain degree of directional bonding character. The Zener anisotropy factor (A = 0.171) deviates significantly from unity, confirming elastic anisotropy in the crystal. This is further supported by the relatively high universal anisotropy index (AU = 4.835). The calculated sound velocities (VS, VL, and Vm) and Debye temperature (θD = 98.468 K) provide additional insight into lattice dynamics and bonding strength. The relatively low Debye temperature suggests weak interatomic bonding and soft lattice behavior. Overall, these results confirm that Cs3SCl is mechanically stable, relatively soft, elastically anisotropic, and exhibits ductile characteristics, making it suitable for further investigation in optoelectronic applications. Formation energy of Cs3SCl anti-perovskite Formation energy is a very important indicator in assessing the thermal stability of a solid, because it indicates how energetically favorable the compound is compared to its constituent elements. In general, if the formation energy of a system is negative, it exhibits a tendency to form spontaneously and is considered thermally stable. In this study, the formation energy of Cs3SCl anti-perovskite compounds was determined using the total energy obtained from first-principles-based Density Functional Theory (DFT) calculations. The calculation is carried out using eqn (15) and (16), which are consistent with the established and widely used methods in previous studies.20,77–80 The results obtained are presented in Table 3. According to the calculated results, the total formation energy of the Cs3SCl compound was found to be −14.04 eV, while the formation energy per atom was determined to be −2.81 eV per atom. In both cases, the negative value clearly indicates that the formation of this compound is energetically favorable and its synthesis is thermally feasible in a real environment. Additionally, this significantly negative formation energy value indicates the existence of strong chemical bonds between the Cs, S, and Cl atoms, which increases the overall stability of the crystal structure. Such a strong bond helps prevent structural degradation and enables the compound to maintain its stability even under high temperatures or external environmental influences. Overall, these results from the formation energy analysis demonstrate that the Cs3SCl anti-perovskite compound is thermally stable and suitable for long-term usability. This thermal stability provides a solid foundation for the material's future use in photovoltaic, optoelectronic, and other energy-related technological applications.15Formation energy, ΔEf = EtotCs3SCl − (3EtotCs + EtotS + EtotCl) Table 3Formation and total energy analysis of the Cs3SCl anti-perovskiteMaterialTotal energy (Ry)Total energy (eV)Atom numberFormation energy (eV)Formation energy (eV per atom)Cs3SCl−171.80115−14.04−2.81Cs−40.27361——S−20.136321——Cl−29.81191—— Formation and total energy analysis of the Cs3SCl anti-perovskite Formation energy per atom,16 Electronic features of Cs3SCl anti-perovskite The electronic characteristics of a component are primarily controlled by the distribution and motion of its electrons and energy levels. These factors counted not only the electrical conductivity but also the material's response to external electric fields. In electronic characteristics analysis, three primary factors are usually considered: band structure, electric potential, and partial density of states (PDOS).1,2 In this current study, electrostatic potential characteristics analysis was of particular significance, as it enables the calculation of electron affinity, a critical parameter for evaluating the suitability of a material in photovoltaic or photocatalytic applications.6,7 Extensive analysis of the band structure, PDOS, and potential profile was performed to evaluate whether the proposed Cs3SCl anti-perovskite could work effectively in real-world electronic devices. As well, these analyses provide reliable information about carrier transport, energy level configuration, and the potential of the material for technological applications.20,21,28 Bandgap features of Cs3SCl anti-perovskite Determining the electronic bandgap is important because it indicates whether a material is a semiconductor or a metal. The bandgap directly affects the optical absorption capacity of a material, charge carrier transport, and the performance of devices such as photodetectors or solar cells. Through the bandgap value of a material, we can predict how efficiently it is able to create and transport charges when light falls on it. In the present study, the band structure of Cs3SCl anti-perovskite is shown in Fig. 3(a), where the Fermi level is set to zero for the convenience of analysis.1,2,6,7 In Fig. 3(a), the electronic band structure of Cs3SCl anti-perovskite is presented in two different exchange–correlation methods, where the clear semiconducting nature of the material can be observed in both GGA-PBE and HSE06. Although the bandgap of 1.185 eV is found to be relatively small in the GGA-PBE calculations, the HSE06 method shows a significantly larger bandgap of 2.051 eV, which is usually due to the reduction of self-interaction defects resulting from the use of hybrid functionals. In both methods, the valence band maximum and conduction band minimum are located at the same high-symmetry Γ–Γ point, which directly confirms the presence of a bandgap. This feature facilitates rapid electron–hole pair formation after light absorption and enables efficient charge extraction without additional phonon assistance. Also, the relatively high dispersion of the conduction band facilitates electron transport, which can play an important role in reducing carrier recombination. Comparative analysis of GGA-PBE and HSE06 results suggests that the electronic structure of Cs3SCl provides a strong foundation suitable for solar energy harvesting. Specifically, the bandgap value found by HSE06 establishes it as a potential material for photovoltaic absorbers, photodetectors, and other optoelectronic devices.20,21,28 (a) Band structure along selected high-symmetry k-paths and (b) partial density of states of the Cs3SCl anti-perovskite. The effective mass of charge carriers in the Cs3SCl anti-perovskite has been analyzed using the GGA–PBE-based electronic band structure shown in Fig. 3(a). In this analysis, special emphasis is given to the region around the conduction band minimum (CBM) located at the top of the Γ point of the band structure and the valence band maximum (VBM) located below, because these regions mainly play a controlling role in the transport of electrons and holes. The parabolic fitting method has been applied to the band portion near the VBM and CBM to determine the effective mass. In this method, the relationship between energy (E) and a wave vector (k) is fitted in a quadratic form, which helps the effective masses of holes (mh) and electrons (me) be accurately calculated. To calculate the charge transport properties, eqn (17)–(20) are used.1,7,20,21 Hole/electron effective mass:17 Conduction band of states:18 Valence band of states:19 Hole/electron mobility:20Here, e denotes the electric charge of the electron, and KB denotes the Boltzmann constant. In this study, the effective density of states, NCV and NVB, of the conduction band and valence band, respectively, at a temperature of 300 K, were calculated. In addition, the mobility of electrons (µe) and holes (µh) has been determined for a relaxation time τ = 10−14 s to analyze carrier transport at the same temperature. These computational assumptions and methods are consistent with previously published research findings, further strengthening the reliability of the current analysis.1,7,20,21 The charge-transport parameters of Cs3SCl were evaluated through the calculated carrier effective masses, density of states, and carrier mobilities. As listed in Table 4, the electron effective mass (me = 0.579 m0) is considerably lower than the hole effective mass (mh = 1.526 m0), indicating that electrons can move more easily through the crystal lattice than holes. This behaviour is further reflected in the carrier mobility values, where the electron mobility (µe = 30.3 cm2 V−1 s−1) is nearly 2.6 times higher than the hole mobility (µh = 11.5 cm2 V−1 s−1). The relatively high electron mobility suggests efficient electron transport and reduced carrier-transport resistance, which are advantageous for photovoltaic and optoelectronic applications. Furthermore, the calculated effective density of states in the valence band (NVB = 4.74 × 1019 cm−3) is larger than that in the conduction band (NCB = 1.11 × 1019 cm−3), implying a greater availability of electronic states near the valence-band edge. Overall, the moderate carrier effective masses, together with the favourable carrier mobilities, indicate that Cs3SCl possesses promising charge-transport characteristics, supporting its potential use as an efficient absorber material in solar-energy conversion devices.1,7,20,21 Table 4Charge transport behavior of the Cs3SCl anti-perovskiteStructureHole effective mass, Electron effective mass, VB effective DOS, NVB (cm−3)CB effective DOS, NCB (cm−3)Hole mobility, µh (cm2 V−1 s−1)Electron mobility, µe (cm2 V−1 s−1)ReferenceCs3SCl1.526 m00.579 m04.74 × 10191.11 × 101911.530.3This workNa3OI0.7171 m00.2859 m01.52 × 10193.82 × 101824.4961.43 6 Na3OBr2.72 m00.219 m01.13 × 10202.56 × 10186.4680.2 7 Na3SBr0.5623 m00.3184 m01.05 × 10194.50 × 101831.2355.16 1 K3SeBr2.15 m00.455 m02.5 × 10197.68 × 10188.1738.7 28 K3SeI2.0612 m00.4174 m07.39 × 10196.75 × 10188.5342.2 20 Cs3SBr1.53 m00.539 m04.73 × 10199.89 × 101811.532.6 21 Charge transport behavior of the Cs3SCl anti-perovskite Partial density of states of Cs3SCl anti-perovskite Fig. 3(b) shows the partial density of states (PDOS) of Cs3SCl anti-perovskite, where different particular atomic orbitals are marked in different colors. The horizontal axis indicates the energy (E–EF) relative to the Fermi level (EF).28,81,82 The valence band is mainly controlled by the S-2p orbital, indicating that the sulfur atom plays an important role in hole production and redox processes. The main part of the conduction band is made up of Cs-2s and Cs-3p orbitals, which ensure efficient electron transport. The Cl orbital contributes a very limited portion near the band edge, which is advantageous in reducing electronic scattering and ensuring proper transitions. The clear separation of S-derived and Cs-derived states helps to separate electron–holes, reduces recombination, and increases charge transport efficiency. These properties make Cs3SCl highly suitable for use in solar energy conversion, visible light-driven photocatalysis, and optoelectronic devices, where strong light absorption and efficient charge transfer are essential.1,2,21 Electrostatic potential features of Cs3SCl anti-perovskite Calculations have been carried out using the slab structure shown in Fig. 4(a) to determine the electrostatic potential properties of the Cs3SCl compound. Knowing the precise location of the work function and band edge of a material is very important, as these values determine the charge transfer efficiency in photovoltaic and optoelectronic devices and directly impact carrier injection and overall device performance. The analysis results of the electrostatic potential profile obtained from the slab model are presented in Fig. 4(b) and Table 5. The mathematical relationships and formulas (21)–(23) are used to determine these electrical properties are mentioned below.1,21,2821Work function: ϕ = Evacumm − EFermi22Electron affinity: χ = Evacumm − ECBM23Ionization energy: IE = Evacumm − EVBMwhere EVBM and ECBM = valence band maximum and conduction band minimum, respectively.1,21,28Table 5 presents a comparative analysis of the electrostatic potential-related parameters of the Cs3SCl anti-perovskite with previously reported materials. The vacuum level energy of Cs3SCl (5.123 eV) is slightly higher than that of the compared materials, indicating a relatively deeper potential level, which can influence charge carrier extraction at interfaces. The ionization energy (IE) of Cs3SCl is found to be 4.53 eV, which is higher than that of most reported compounds, suggesting a strong binding of valence electrons and stable electronic structure. The work function (ϕ) of Cs3SCl (2.055 eV) is relatively low compared to Na3OI (2.613 eV), Na3OBr (3.03 eV), and Na3SBr (2.943 eV), but is comparable to Cs3SBr (2.03 eV) and slightly higher than K3SeBr (1.894 eV). A lower work function facilitates efficient electron emission and improves charge transfer at the interface, which is beneficial for photovoltaic device performance. Furthermore, the electron affinity (χ) of Cs3SCl (4.53 eV) is relatively high compared to most of the listed materials, indicating a strong tendency to accept electrons. This characteristic is advantageous for enhancing electron transport and reducing recombination losses. Overall, the electrostatic potential parameters suggest that Cs3SCl possesses a favorable energy level alignment, with balanced ionization energy, low work function, and high electron affinity, making it a promising candidate for efficient charge transport and optoelectronic device applications. (a) (001) slab model of the Cs3SCl anti-perovskite constructed for electrostatic potential calculations and (b) the corresponding electrostatic potential profile. Table 5Electrostatic potential features of Cs3SCl anti-perovskite in comparison with previous studiesAnti-perovskite structureVacuum level energy (eV)Ionization energy, IE (eV)Work function, ϕ (eV)Electron affinity, χ (eV)ReferenceCs3SCl5.1234.532.0554.53This workNa3OI4.9633.9572.6133.957 6 Na3OBr4.38693.4493.033.449 7 Na3SBr4.83803.5702.9433.570 1 K3SeBr4.5283.6651.8943.665 28 K3SeI4.5743.7222.6373.722 20 Cs3SBr4.4983.9472.033.947 21 Electrostatic potential features of Cs3SCl anti-perovskite in comparison with previous studies Optical properties of Cs3SCl anti-perovskite The analysis of optical properties is essential to evaluate the suitability of a material for optoelectronic and photovoltaic applications.1,21,28 Optical properties describe how a material interacts with incident light through absorption, refraction, reflection, transmission, and energy dissipation processes, which are directly governed by its electronic structure.1,21,28 In solar cell and photocatalytic applications, these properties determine the efficiency of light absorption and the generation of charge carriers. Therefore, a detailed understanding of optical behavior is necessary to assess the material's light-harvesting capability. In this work, the optical properties of the Cs3SCl anti-perovskite compound have been systematically investigated. Key parameters such as the real and imaginary parts of the dielectric function, absorption coefficient, reflectivity, refractive index, extinction coefficient, penetration depth, optical depth, and energy loss function have been analyzed over a wide range of photon energy and wavelength. Dielectric function of Cs3SCl anti-perovskite The dielectric function, ε(ω), is a fundamental parameter for describing the optical response of a material to incident electromagnetic radiation. It consists of two components: the real part ε1(ω), which represents the energy storage capability (polarization), and the imaginary part ε2(ω), which is associated with optical absorption and energy dissipation due to interband electronic transitions. These components are strongly dependent on photon energy and provide important insight into the interaction between light and the electronic structure of the material. In particular, ε2(ω) is directly related to electronic transitions between the valence and conduction bands and is useful for analyzing the optical bandgap. The relationship between ε1(ω) and ε2(ω) is governed by the Kramers–Kronig relations, ensuring the physical consistency of the calculated optical properties.1,28,83 In this work, the dielectric function is calculated using standard first-principles approaches based on eqn (24)–(26).1,21,28 This analysis provides a clear understanding of light–matter interaction in Cs3SCl and supports its potential for optoelectronic and photovoltaic applications.24Dielectric function: ε(ω) = ε1(ω) + iε2(ω) Real part of dielectric function:25 Imaginary part of dielectric function:26where, P = prime number of the integer. As shown in Fig. 5(a), the real part ε1(ω) exhibits a positive value in the low-energy region with a static dielectric constant of approximately ∼1.628, indicating normal dielectric behavior and effective polarization of the material under incident radiation. With increasing photon energy, ε1(ω) shows several fluctuations due to electronic transitions and reaches a prominent peak of about ∼2.0 around 3–4 eV photon energy range. Beyond this region, ε1(ω) gradually decreases and becomes negative near ∼12.5 eV, indicating a transition to metallic-like behavior where the material reflects incident radiation strongly. Fig. 5(b) shows the imaginary part ε2(ω), which represents the absorption behavior of the material. The onset of ε2(ω) occurs around ∼1.185 eV, indicating the optical absorption edge. Several distinct peaks are observed in the energy range of ∼3–6 eV, which are attributed to interband transitions between valence and conduction bands. A strong and sharp peak is also observed near ∼12 eV, corresponding to high-energy electronic transitions. Overall, the combined dielectric response suggests that Cs3SCl exhibits significant optical activity in the visible and ultraviolet regions, confirming its strong light absorption capability and suitability for photovoltaic and optoelectronic applications. Frequency-dependent dielectric response of Cs3SCl anti-perovskite: (a) real part (ε1) and (b) imaginary part (ε2) of the dielectric function. Table 6 presents a comparative analysis of the dielectric properties of the Cs3SCl anti-perovskite with previously reported related materials. It is observed that the static dielectric constant ε1(0) of Cs3SCl (1.628) is relatively lower than that of Na3OI (2.62), Na3OBr (3.03), and Na3SBr (2.62), but remains comparable to Cs3SBr (1.6823) and slightly lower than K3SeBr (1.91) and K3SeI (2.064). This relatively moderate value indicates a balanced polarization response, which is beneficial for minimizing charge recombination while maintaining sufficient dielectric screening. Similarly, the high-frequency dielectric constant ε1(∞) of Cs3SCl (0.545) is lower than most of the reported materials, suggesting reduced electronic polarization at higher photon energies. This behavior is advantageous for limiting optical losses and improving transparency in the higher energy region. Furthermore, the initial critical point of the imaginary dielectric function ε2(ω) for Cs3SCl is observed at 1.185 eV, which is lower than that of most compared materials. This lower onset energy indicates that Cs3SCl can initiate optical absorption at relatively lower photon energies, making it more effective in harvesting visible light. Overall, the comparative results suggest that Cs3SCl exhibits a favorable dielectric profile with moderate polarization, low high-frequency response, and early absorption onset, highlighting its potential as an efficient material for photovoltaic and optoelectronic applications. Table 6Comparative analysis of the dielectric properties of Cs3SCl anti-perovskite with previously reported materialsConstructionStatic dielectric constant, ε1(0)High-frequency dielectric constant, ε1(∞)Initial critical point position of, ε2(ω) (eV)ReferenceCs3SCl1.6280.5451.185This workNa3OI2.620.942 6 Na3OBr3.030.721.8756 7 Na3SBr2.620.782 1 K3SeBr1.910.981.65 28 K3SeI2.0640.981.7047 20 Cs3SBr1.68230.561.102 21 Comparative analysis of the dielectric properties of Cs3SCl anti-perovskite with previously reported materials From the perspective of photovoltaic applications, the observed dielectric behavior of Cs3SCl is particularly advantageous. The relatively high dielectric response in the visible-energy region indicates effective dielectric screening, which can facilitate the separation of photogenerated electron–hole pairs and reduce carrier recombination losses. Furthermore, the prominent interband-transition features observed in ε2(ω) confirm strong light–matter interaction and efficient photon absorption. These characteristics are beneficial for enhancing carrier generation and charge-collection efficiency in solar-cell devices. Therefore, the dielectric response of Cs3SCl further supports its suitability for photovoltaic and optoelectronic applications. Optical properties of Cs3SCl anti-perovskite based on absorption, reflection, refraction, and extinction coefficients A comprehensive analysis of the optical properties of the Cs3SCl compound is essential, as these properties govern the interaction between light and the material. Key optical parameters such as absorption coefficient, reflectivity, refractive index, and extinction coefficient provide important insights into light propagation, energy absorption, and dissipation mechanisms. The absorption coefficient describes how effectively the material absorbs incident light, which is crucial for photovoltaic applications. The reflectivity indicates the fraction of incident light reflected from the material surface, influencing optical losses. The refractive index determines how light propagates through the material and governs light bending and phase velocity, which are important for optical device design. The extinction coefficient represents the attenuation of light intensity within the material due to absorption processes. These parameters collectively determine the efficiency of light utilization and energy conversion. In this work, these optical properties are calculated using the standard relations given in eqn (27)–(30).1,6,7,28 Absorption coefficient:27 Extinction coefficient:28 Refractive index,29 Reflectivity,30 The optical absorption spectrum of Cs3SCl is presented in Fig. 6(a) over a wide wavelength range. The compound exhibits very strong absorption in the ultraviolet (UV) region, where the maximum value of the absorption coefficient reaches about 2.6 × 105 cm−1. More importantly, the absorption coefficient remains at about 2.5 × 104 cm−1 throughout the visible (380–750 nm) region, indicating its ability to effectively absorb a significant portion of sunlight. Such absorption strength is very favorable for solar cell absorber materials, as it can ensure efficient light harvesting even with relatively thin absorber layers. Furthermore, the absorption coefficient remains at about 2 × 104 cm−1 in the infrared region beyond 760 nm, indicating its continued optical activity at longer wavelengths. The combination of high absorption in the ultraviolet region, stable absorption in the visible region, and significant optical response in the infrared region indicates that Cs3SCl is capable of effectively utilizing a broad portion of the solar spectrum. Its optical absorption properties therefore establish it as a potential material for high-efficiency photovoltaic and other optoelectronic applications.1,6,7,28 Optical response characteristics of Cs3SCl anti-perovskite: (a) absorption coefficient, (b) extinction coefficient, (c) refractive index, and (d) reflectivity. Fig. 6(b) shows the variation of the extinction coefficient k(ω) of the Cs3SCl compound in the wavelength region extending from the ultraviolet to the infrared, which is a very important parameter in determining the light absorption efficiency and light decay properties of the material. Observations show that in the ultraviolet region (about 200–380 nm) the value of k(ω) is relatively high, around 0.4, and there are multiple sharp peaks and oscillations in this region. Such a trend indicates that the interaction between photons and electrons in the UV region is very strong and the density of interband electronic transitions is significantly high. As a result, the absorption and energy dissipation capacity of UV photons in this region is very effective. In the visible wavelength range (approximately 380–700 nm), the extinction coefficient gradually decreases to a value of approximately 0.15–0.2, indicating that light loss in this region is relatively low. That is, Cs3SCl exhibits partially transparent behavior in visible light, and photons can easily pass through the material. In the infrared region, the k value decreases further (below about 0.12) and maintains a nearly flat trend, indicating low-loss infrared light transport. This property makes the material suitable for handling low-energy IR photons. The moderate extinction coefficient in the visible region, together with the appreciable absorption coefficient, indicates a favorable optical response for efficient photon harvesting and charge-carrier generation in photovoltaic devices. Therefore, Cs3SCl is expected to be a promising candidate for photovoltaic and optoelectronic applications.1,6,7,28 Fig. 6(c) shows the change in the refractive index of the compound Cs3SCl in the ultraviolet to infrared wavelength range. The analysis shows that there is a sudden change in the refractive index and a clear peak value (around 1.3) in the UV region, indicating the strong scattering tendency of the material. This type of scattering behavior is usually seen as a result of strong interactions between photons and electrons, or excitonic effects. The refractive index exhibits a relatively smooth and stable behavior in the visible region, and its value is limited to the range of approximately 1.25–1.3. This stability indicates that the material is capable of ensuring balanced optical transport in the visible light range. On the other hand, the refractive index remains almost unchanged in the infrared region, which is consistent with low-loss light transport properties. This refractive index property makes Cs3SCl suitable for use in optical lenses, waveguides, light modulators, and optical components requiring low reflectivity in the visible region. In particular, its use as a refractive index-matching anti-reflection coating (ARC) layer in solar cells can help ensure effective penetration of sunlight. Moreover, the stable refractive index in the visible region can improve light confinement and optical path length within the absorber layer, thereby enhancing photon utilization and potentially improving solar-cell performance.1,6,7,28 Fig. 6(d) shows the change in the reflection index of the Cs3SCl compound from the ultraviolet to the infrared wavelength region. The analysis shows that the reflectance value in the ultraviolet region is relatively high, lying in the range of about 0.04–0.065, indicating strong interactions between photons and material in this region. This fluctuation is also consistent with the absorption features observed in the UV region. The reflection index decreases significantly in the visible wavelength range and is limited to a value of approximately 0.02–0.025. This low reflection behavior indicates that visible light can mostly penetrate through the material with minimal reflection at the surface, resulting in the material exhibiting high light transmission properties for visible light. The reflectance value is also relatively low and almost stable in the infrared region, indicating the infrared transparency of the material. Due to its extremely low reflectance properties in visible light, the Cs3SCl compound is particularly promising for use as anti-reflection coatings, optical windows, and optical layers in infrared sensors. This material can play an effective role in increasing light penetration and reducing reflection loss, especially in high-efficiency solar cells. The low reflectivity observed throughout the visible region is particularly advantageous for photovoltaic applications because it minimizes optical losses at the surface and allows a larger fraction of incident sunlight to enter the absorber layer. Consequently, more photons become available for charge-carrier generation, which is beneficial for improving device efficiency.1,6,7,28 Effect of optical depth, energy-loss function, and penetration depth on the optical response of Cs3SCl anti-perovskite A detailed analysis of penetration depth, optical depth, and energy-loss function of Cs3SCl anti-perovskite element is essential to understand the propagation and attenuation of electromagnetic radiation within a material. The penetration depth describes how far incident light can travel inside the material before its intensity significantly decreases, which is important for evaluating light absorption efficiency in photovoltaic and photocatalytic systems. The optical depth represents the extent of light attenuation as it propagates through the material and is directly related to its absorption characteristics. Meanwhile, the energy-loss function provides information about the energy dissipated by fast electrons interacting with the material, which is associated with collective electronic excitations. The combined analysis of these parameters offers valuable insight into light–matter interaction, energy dissipation mechanisms, and charge carrier generation. In this work, these properties are calculated using the standard relations given in eqn (31)–(33).1,6,7,28 Penetration depth:31 Optical depth:32(ω) = α(ω) × d Energy loss function:33Here, the optical depth was carried out assuming the medium to be nearly 8 µm in thickness. Fig. 7(a) shows the wavelength-dependent change in the light penetration depth of the Cs3SCl anti-perovskite compound. In the ultraviolet (UV) region, especially in the range of about 120–200 nm, the penetration depth is observed to be extremely low, indicating that the high energy photons in this region are mostly absorbed near the surface of the material. This trend is the result of strong interband electronic transitions and is consistent with the high absorption behavior in the UV region. The penetration depth gradually increases in the visible region (approximately 400–700 nm), indicating the ability of light to penetrate relatively deeply. Penetration depth increases further in the infrared region, suggesting that low-energy photons in this region can travel relatively long distances within the material. This feature can play an important role in determining the thickness of the absorber layer in solar cells and increasing the efficiency of light utilization in the photocatalytic process.1,6,7,28 Optical response characteristics of Cs3SCl anti-perovskite: (a) penetration depth, (b) optical depth, and (c) energy-loss spectrum. Fig. 7(b) shows the optical depth or optical attenuation depth, which indicates how quickly light weakens as it travels through the material. The optical depth value in the UV region is very high and multiple peaks are observed, which provides evidence of rapid absorption of light and high energy loss in this region. The optical depth in the visible region decreases significantly and exhibits a relatively smooth trend, indicating that light decays slowly in this region. The optical depth reaches its lowest point in the infrared region, so low-energy light can pass through the material with very little attenuation. This behavior makes Cs3SCl potential for light transport-based optical devices and IR-based technologies.1,6,7,28 Fig. 7(c) presents the energy loss spectrum (energy loss function), which indicates how much energy a photon or electromagnetic radiation loses during its interaction with a material. High values of the energy decay function and multiple peaks are observed in the UV region, indicating plasmon-like excitation and strong electron collective reactions. The energy loss in the visible region is relatively low and slowly changing, indicating that light is transmitted relatively stably in this region. Energy loss is further reduced in the infrared region, suggesting that low-energy radiation loses very little energy after penetrating the material.1,6,7,28 Overall, the combined analysis of light penetration depth, optical attenuation, and energy decay spectrum indicates that the Cs3SCl compound is a highly effective light absorber in the UV region, and it behaves as a light-transporting material with relatively low attenuation in the visible and infrared regions. Due to these properties, Cs3SCl can be considered a potential anti-perovskite material for use in solar cells, photocatalytic systems, optoelectronic devices, and modern technologies based on energy conversion.1,6,7,28 Analysis of band alignment and energy band profile of Cs3SCl absorber-based solar cell The main objective of this study is to thoroughly evaluate the overall performance of anti-perovskite solar cells (APSCs) designed using Cs3SCl anti-perovskite absorber layers. The outline of the proposed solar cell structure is presented in Fig. 8. The required physical and electrical parameters of the materials used for the different layers, such as Sb2S3, Zn3P3, CuO, Cu2Te, FTO, and SnS2, are collected from previously published studies and compiled in Table 7. On the other hand, the interface-related defect characteristics of the single-absorber APSC structure based on Al/FTO/SnS2/Cs3SCl/HTL/Se are presented in detail in Table 8. The selection of SnS2 as the electron transport layer (ETL) is strongly motivated by its favorable band alignment with the Cs3SCl absorber, as clearly illustrated in Fig. 9–Fig. 10. The conduction band minimum (CBM) of SnS2 is closely aligned with that of Cs3SCl, forming a small positive conduction-band offset (spike-like alignment), which facilitates efficient electron extraction from the absorber to the ETL. At the same time, this alignment acts as a barrier for hole transport toward the ETL, thereby effectively suppressing interfacial recombination losses. Furthermore, the relatively stable conduction-band profile observed at the SnS2/Cs3SCl interface across all device configurations (Fig. 10(a–d)) confirms that SnS2 ensures consistent electron transport behavior independent of the HTL selection. In addition to band alignment, SnS2 offers high electron mobility, wide bandgap-induced optical transparency, and good chemical stability, making it a suitable and reliable ETL for high-performance anti-perovskite solar cells. For the back contact, Se was selected based on a comparative evaluation of several candidate materials. Initially, different back contact materials were examined, and Se exhibited the most favorable device performance among them. This can be attributed to its appropriate work function, which provides efficient hole extraction from the HTL while minimizing energy barrier formation at the rear interface. As a result, the Se back contact reduces carrier recombination losses and improves overall charge collection efficiency, thereby enhancing the device performance. Fig. 9 shows the overall band alignment diagram of the proposed device, where aluminum (Al) is considered as the front junction, selenium (Se) as the back junction, SnS2 as the electron transport layer, Cs3SCl as the absorber layer, and various hole transport layers (HTL) have been added as well. For a more in-depth analysis, Fig. 10(a–d) shows the comparative band diagrams of a 0.750 µm thick Cs3SCl absorber layer coupled with four different HTLs: Sb2S3, Zn3P3, CuO, and Cu2Te, where a 0.25 µm thick SnS2 layer was used as the uniform electron transport layer in all cases. This analysis maps the conduction band (EC), valence band (EV), electron quasi-Fermi level (Fn), and hole quasi-Fermi level (Fp) across the entire thickness of the device, through which the interface-based band alignment, charge carrier extraction process, and recombination tendency have been evaluated. In all structures, the Cs3SCl absorber layer exhibits a well-coordinated and stable intrinsic band profile, with clear quasi-Fermi level splitting, which provides evidence of effective charge carrier creation and separation under light irradiation. However, the nature of the SnS2 layer significantly affects the conduction-band offset at the SnS2/Cs3SCl junction, which plays an important role in controlling the electron transport efficiency and recombination behavior. Similarly, the type of HTL used determines the valence-band offset at the Cs3SCl/HTL junction, which directly affects the hole transport and charge depletion processes. As a result, the selection of appropriate HTL and ETL appears to be very important in improving the overall performance of this solar cell structure. Schematic illustration of the proposed Al/FTO/SnS2/Cs3SCl/HTL/Se solar-cell architecture, where Cs3SCl serves as the absorber layer. Table 7Optoelectronic parameter of Cs3SCl anti-perovskite absorber with HTL, and ETL materials used in SCAPS-1DaParameterSnS2 (ref. 1)Cu2Te84Sb2S3 (ref. 85)Zn3P2 (ref. 86)FTO6Cs3SCl (this work)CuO20 W th (cm)0.25 *0.25 *0.25 *0.25 *0.25 *0.750*0.25 * E g (eV)1.851.181.621.53.51.1852.1 X e (eV)4.264.23.74.244.533.2 ε r 17.7107.087.1191.6287.11 N CB (cm−3)7.32 × 10187.8 × 10172 × 10192.2 × 10182.2 × 10181.11 × 10192.2 × 1018 N VB (cm−3)1 × 10191.6 × 10191 × 10191.8 × 10191.8 × 10194.74 × 10191.8 × 1018 V te (cm s−1)1 × 1071 × 1071 × 1071 × 1071 × 1071 × 1071 × 107 V th (cm s−1)1 × 1071 × 1071 × 1071 × 1071 × 1071 × 1071 × 107 µ e (cm2 V−1 s−1)5 × 1015009.812 × 10130.33.4 µ h (cm2 V−1 s−1)2.5 × 101100103.81 × 10111.53.4 N D (cm−3)9.85 × 10190002 × 101900 N A (cm−3)01 × 10215.7 × 10151 × 101401 × 1016*1 × 1020 N t (cm−3)1 × 10141 × 10151 × 10141 × 10141 × 10151 × 1015 *1 × 1015a*A variable domain approach was adopted for the initial research and simulation studies. Note: in this work, the performance of a single-junction solar cell based on Cs3SCl has been investigated. All input parameters used in the SCAPS-1D simulation were derived from PBE-calculated values to ensure consistency within the device modeling framework. The HSE06 functional was employed only to obtain a more accurate estimation of the bandgap, which is calculated to be 2.051 eV. This bandgap corresponds to photon absorption up to approximately 620 nm, which lies within the visible region (380–750 nm). Therefore, despite having a relatively wide bandgap, Cs3SCl is capable of absorbing a significant portion of visible light, supporting its applicability in photovoltaic devices. Optoelectronic parameter of Cs3SCl anti-perovskite absorber with HTL, and ETL materials used in SCAPS-1Da *A variable domain approach was adopted for the initial research and simulation studies. Note: in this work, the performance of a single-junction solar cell based on Cs3SCl has been investigated. All input parameters used in the SCAPS-1D simulation were derived from PBE-calculated values to ensure consistency within the device modeling framework. The HSE06 functional was employed only to obtain a more accurate estimation of the bandgap, which is calculated to be 2.051 eV. This bandgap corresponds to photon absorption up to approximately 620 nm, which lies within the visible region (380–750 nm). Therefore, despite having a relatively wide bandgap, Cs3SCl is capable of absorbing a significant portion of visible light, supporting its applicability in photovoltaic devices. Table 8Interface defect of the Cs3SCl absorber-based solar cellParameterSnS2/Cs3SCl and Cs3SCl/HTLType of defectNeutralCross section area for electron and hole (cm2)1.00 × 10−19Energetic distributionSingleEnergy level EtAbove the highest eVReference energy Er (eV)0.600Total density (cm−3)1.00 × 1010 Interface defect of the Cs3SCl absorber-based solar cell Energy band diagram of the proposed Al/FTO/SnS2/Cs3SCl/HTL/Se solar-cell architecture, illustrating the band alignment between the absorber, transport layers, and metal contacts. Energy band profiles across the device thickness of the Cs3SCl absorber-based solar cell employing various hole transport layer (HTL) materials: (a) Cu2Te, (b) Sb2S3, (c) CuO, and (d) Zn3P2. Fig. 10(a–d) presents the energy-band arrangement resulting from the use of four different hole transport layers (HTL), Sb2S3, Zn3P2, CuO, and Cu2Te, in anti-perovskite solar cells with a Cs3SCl (0.75 µm) absorber layer. The FTO (0.25 µm) front junction and SnS2 (0.25 µm) electron transport layer (ETL) are kept the same in all structures so that the actual impact of HTL changes can be clearly assessed. In Fig. 10(a) a relatively smooth valence-band alignment is observed at the Cs3SCl/HTL interface in the case of using Cu2Te HTL. The conduction band (EC) and valence band (EV) are well aligned inside the Cs3SCl absorber layer, and the quasi-Fermi level splitting (Fn–Fp) is clearly visible, indicating effective charge carrier generation under light excitation. The relatively small valence-band offset at the Cs3SCl/Cu2Te interface promotes efficient hole extraction while minimizing energy loss during carrier transport. Such an energy-band arrangement reduces interfacial carrier accumulation and suppresses recombination, thereby improving charge-collection efficiency. In Fig. 10(b), the valence-band offset at the Cs3SCl/HTL interface in the Sb2S3 HTL-coupled structure is relatively enhanced. This favorable energy configuration facilitates the hole extraction process and assists the charge transport from the absorber layer towards the HTL. In Fig. 10(b), the valence-band offset at the Cs3SCl/HTL interface in the Sb2S3 HTL-coupled structure is relatively enhanced. This favorable energy configuration facilitates the hole extraction process and assists the charge transport from the absorber layer towards the HTL. The use of CuO HTL in Fig. 10(c) results in a significant valence-band offset observed at the Cs3SCl/HTL interface, which provides an effective driving force for hole transport. This energy difference accelerates hole extraction from the absorber layer and reduces the tendency for charge accumulation at the interface. At the same time, the conduction-band offset at the SnS2/Cs3SCl junction is relatively stable, maintaining the electron extraction efficiency. As a result, the CuO-based structure exhibits balanced performance in both charge separation and transport. In Fig. 10(d), a relatively large valence-band offset is observed at the Cs3SCl/HTL junction in the case of using Zn3P3 HTL. This additional energy barrier can partially restrict hole transport, thereby increasing the recombination probability in the interface region. Although the band profile inside the Cs3SCl absorber layer remains stable and photogenerated charge carrier generation occurs efficiently, the overall charge extraction efficiency may be relatively reduced as the energy balance with HTL is less favorable. Comparative analysis of the four structures clearly shows that the Cs3SCl absorber layer maintains a stable internal band structure in all cases, confirming its strong charge-generation capability under illumination. Nevertheless, the overall device performance is strongly influenced by the conduction-band offset at the SnS2/Cs3SCl interface and the valence-band offset at the Cs3SCl/HTL interface. Among the investigated HTLs, Cu2Te exhibits the most favorable overall energy-band alignment, facilitating efficient hole extraction while suppressing interfacial charge recombination. The relatively smooth valence-band transition between Cs3SCl and Cu2Te reduces carrier accumulation at the interface and promotes effective charge transport toward the back contact. Consequently, the Cu2Te-based configuration is expected to provide superior photovoltaic performance compared with the other HTLs investigated in this work. Photovoltaic performance analysis of Cs3SCl anti-perovskite–based solar cell Fig. 11(a) presents the J–V characteristics of Cs3SCl absorber-based solar cells using different hole transport layers (HTL). It can be seen that almost similar J–V profiles are maintained for all structures, indicating that the Cs3SCl absorber layer exhibits stable charge generation and transport capabilities. However, the change in HTL results in noticeable differences in short-circuit current density (JSC), fill factor (FF), and overall power conversion efficiency (PCE). According to the data in Table 9, the device employing Cu2Te as the HTL achieves the highest JSC (39.354 mA cm−2) and the highest PCE (22.72%). This superior performance can be attributed to several factors. First, the favorable valence-band alignment at the Cs3SCl/Cu2Te interface facilitates efficient hole extraction from the absorber layer. Second, the relatively small interfacial energy barrier suppresses carrier accumulation and minimizes recombination losses at the absorber/HTL junction. Third, the improved charge-transfer characteristics enhance carrier collection efficiency, resulting in a higher fill factor. Furthermore, the efficient transport of photogenerated holes toward the back contact contributes to maintaining a high current density. As a result of these combined effects, the Cu2Te-based device exhibits the best overall photovoltaic performance among all investigated HTLs. On the other hand, relatively low FF and PCE are observed in Sb2S3-based solar cells. This decrease is mainly related to the less favorable band offset and higher charge loss at the Cs3SCl/Sb2S3 junction. As a result, a portion of the generated carriers cannot be effectively collected. The structures using CuO and Sb3S3 exhibit intermediate performance, wherein in both cases FF and PCE maintain relatively high values. Especially in the Sb2S3-based structure, the overall efficiency is slightly reduced due to the slightly lower JSC, despite the FF being almost equivalent to Cu2Te. The external quantum efficiency (EQE) spectra shown in Fig. 11(b) show that all HTLs maintain high quantum efficiency over a wide range of the visible spectrum. This indicates that the Cs3SCl absorber layer is highly efficient in light absorption and charge generation. However, the slight change in EQE in the long wavelength region reflects the difference in HTL-dependent charge extraction efficiency. Overall, these results clearly indicate that HTL selection plays an important role in determining the performance of Cs3SCl-based solar cells. In particular, since the highest photovoltaic performance is achieved using Cu2Te HTL, it can be considered a very promising hole transport layer for the proposed Cs3SCl anti-perovskite solar cell structure. Photovoltaic performance of the Cs3SCl absorber-based solar cell employing different hole transport layers (HTLs): (a) current density–voltage (J–V) curves and (b) external quantum efficiency (EQE) spectra. Table 9PV parameters of Cs3SCl absorber-based solar cells for different HTLsStructure J SC (mA cm−2) V o (volts)FF (%)PCE (%)Al/FTO/SnS2/Cs3SCl/Cu2Te/Se39.3540.695982.9622.72Al/FTO/SnS2/Cs3SCl/Sb2S3/Se38.3940.693178.2520.82Al/FTO/SnS2/Cs3SCl/CuO/Se38.5240.693682.6122.07Al/FTO/SnS2/Cs3SCl/P3HT/Se38.6360.694982.9222.26 PV parameters of Cs3SCl absorber-based solar cells for different HTLs Influence of absorber layer thickness on photovoltaic performance parameters (JSC, Vo, PCE, and FF) of Cs3SCl absorber-based APSCs with various HTLs In this study, different HTL materials were used, where SnS2 was adopted as the ETL and Al and Au were used as the front and back contact metals, respectively. In the proposed anti-perovskite solar cells, only the thickness of the absorber layer is changed stepwise from 0.2 to 1.8 µm, while keeping all other layer materials and physical parameters unchanged, so that its impact on device performance can be properly assessed. It can be clearly observed from Fig. 12(a) in the study that for all types of HTL materials used, the open-circuit voltage (Vo) gradually decreases with increasing thickness of the absorber layer. Among the tested HTL materials, the lowest Vo value of 0.6737 V was obtained when using Sb2S3 with an absorber thickness of 1.8 µm. On the other hand, the highest Vo value of 0.732 V was achieved when using Cu2Te HTL with an absorber thickness of 0.2 µm. Next, Fig. 12(b) displays a different trend in the short-circuit current density (JSC). The CuO HTL with an absorber thickness of 0.2 µm yielded the lowest JSC value of 30.28 mA cm−2, while the Cu2Te HTL with an absorber thickness of 1.8 µm yielded the highest JSC value of 39.848 mA cm−2. After that, Fig. 12(c) shows that the lowest FF value of 77.60% was recorded for Sb2S3 HTL and 0.2 µm absorber thickness. In contrast, the highest FF value of 82.97% was achieved using Cu2Te HTL with an absorber thickness of 0.5 µm. However, the combined effect of all these parameters changed the power conversion efficiency (PCE). Fig. 12(d) shows that the lowest efficiency of 17.70% was found for CuO HTL and 0.2 µm absorber thickness. On the other hand, the highest PCE value of 22.72% was achieved using Cu2Te HTL with an absorber thickness of 0.750 µm. Although Cu2Te HTL provided relatively high Vo, JSC, FF, and PCE in all cases, the highest efficiency was specifically obtained at the 0.750 µm absorber thickness. Therefore, Cu2Te can be identified as the best HTL material based on absorber thickness optimization, where Vo = 0.6959 V, JSC = 39.354 mA cm−2, FF = 82.96%, and the highest PCE = 22.72% are achieved when the absorber thickness is 0.750 µm. The effect of Cs3SCl absorber layer thickness on (a) Vo, (b) JSC, (c) FF, and (d) PCE for different HTL-based anti-perovskite solar cells. Influence of absorber layer defect density on photovoltaic performance parameters (JSC, Vo, PCE, and FF) of Cs3SCl absorber-based APSCs with various HTLs To improve the performance of solar cells, it is crucial to deeply analyze the role of defects within the material. If an excessive number of defects are present in the absorber layer, pinholes can easily form, which quickly degrades the thin film structure and significantly reduces the long-term stability and overall efficiency of the device.1 They can generally be divided into shallow and deep defects based on their location and energy level. If the density of such defects is high, the quality of the absorber material is severely affected. According to the Shockley–Read–Hall (RSRH) recombination theory, increasing defect density accelerates the non-radiative recombination process, which directly reduces the charge carrier lifetime significantly.6,7 In the present study, the effects of changing defect densities at different layers of a solar cell on the overall device structure have been analyzed using eqn (34) and (35).1,6,7 Gaining a clear understanding of these defect-related effects is essential for high-performance solar cell design and achieving improved power conversion efficiency.34 Carrier lifetime:35 In this equation, RSRH denotes the recombination rate occurring through the Shockley–Read–Hall process. Here p and n denote the densities of holes and electrons, respectively, and τp and τn denote their respective lifetimes. The parameter Nt indicates the total defect density present in the material, where Vth is the thermal velocity of the charge carriers. On the other hand, pi and ni indicate the density of holes and electrons in the intrinsic state, respectively.1,6,7,21 In this study, different HTL materials were used, where SnS2 was adopted as the ETL and Al and Au were used as the front and back contact metals, respectively. In the proposed anti-perovskite solar cells, only the defect density of the absorber layer is changed stepwise from 1012 to 1016 (cm−3), while keeping all other layer materials and physical parameters unchanged, so that its impact on device performance can be properly assessed. It can be clearly observed from Fig. 13(a)–(d) in the study that for all types of HTL materials used, the Vo, JSC, FF, and PCE all gradually decrease with increasing defect density of the absorber layer. Among the tested HTL materials, the lowest Vo value of 0.628 V was obtained when using CuO with an absorber defect density of 1016 (cm−3). On the other hand, the highest Vo value of 0.999 V was achieved when using Zn3P2 HTL with an absorber defect density of 1012 (cm−3). Next, Fig. 13(b) displays a different trend in the short-circuit current density (JSC), which is reduced slightly. The Sb2S3 HTL with an absorber defect density of 1016 (cm−3) yielded the lowest JSC value of 36.44 mA cm−2, while the Cu2Te HTL with an absorber defect density of 1016 (cm−3) yielded the highest JSC value of 39.52 mA cm−2. After that, Fig. 13(c) shows that the lowest FF value of 71.63% was recorded for Sb2S3 HTL and 1016 (cm−3) absorber defect density. In contrast, the highest FF value of 84.74% was achieved using CuO HTL with an absorber defect density of 1012 (cm−3). However, Fig. 13(d) shows that the lowest efficiency of 16.37% was found for Sb2S3 HTL and 1016 (cm−3) absorber defect density. On the other hand, the highest PCE value of 31.58% was achieved using Cu2Te HTL with an absorber defect density of 1016 (cm−3). Although Cu2Te HTL provided relatively high Vo, JSC, FF, and PCE in all cases, the highest efficiency was specifically obtained at the defect density of 1012 (cm−3). For stable and efficient device performance, the defect density should be maintained within an optimal range, avoiding values that are too low or excessively high.1,6,7,21 Our optimization study indicates that a bulk defect density of 1 × 1015 cm−3 yields the most favorable device response. Therefore, Cu2Te can be identified as the best HTL material based on absorber thickness optimization, where Vo = 0.6959 V, JSC = 39.354 mA cm−2, FF = 82.96%, and the highest PCE = 22.72% are achieved when the absorber total bulk defect density of 1 × 1015 cm−3. The effect of Cs3SCl absorber layer defect density on (a) Vo, (b) JSC, (c) FF, and (d) PCE for different HTL-based anti-perovskite solar cells. Influence of absorber layer shallow acceptor density on photovoltaic performance parameters (JSC, Vo, PCE, and FF) of Cs3SCl absorber-based APSCs with various HTLs Incorporating a small amount of dopant into the absorber layer can significantly enhance the performance of PSCs while also affecting their overall stability. The interface layer further contributes to improving the device's PCE. However, excessive dopant concentrations in the absorber can increase charge-carrier recombination, partially reducing this performance gain.1,6 Thus, careful selection of the dopant level is essential to achieve optimal efficiency in various solar cell architectures.1,6,21 In this study, different HTL materials were used, where SnS2 was adopted as the ETL and Al and Au were used as the front and back contact metals, respectively. In the proposed anti-perovskite solar cells, only the shallow acceptor density of the absorber layer is changed stepwise from 1012 to 1016 (cm−3), while keeping all other layer materials and physical parameters unchanged, so that its impact on device performance can be properly assessed. It can be clearly observed from Fig. 14(a)–(d) in the study that for all types of HTL materials used, the Vo, FF, and PCE all gradually increase with increasing defect density of the absorber layer except only for JSC, which slightly decreases. Among the tested HTL materials, the lowest Vo value of 0.6457 V was obtained when using Zn3P2 with an absorber acceptor density of 1014 (cm−3). On the other hand, the highest Vo value of 0.812 V was achieved when using Cu2Te HTL with an absorber acceptor density of 1018 (cm−3). Next, Fig. 14(b) displays a different trend in the JSC, which is reduced slightly. The Sb2S3 HTL with an absorber acceptor density of 1018 (cm−3) yielded the lowest JSC value of 37.32 mA cm−2, while the Cu2Te HTL with an absorber acceptor density of 1014 (cm−3) yielded the highest JSC value of 39.46 mA cm−2. After that, Fig. 14(c) shows that the lowest FF value of 58.86% was recorded for Sb2S3 HTL and 1014 (cm−3) absorber acceptor density. In contrast, the highest FF value of 85.39% was achieved using Cu2Te HTL with an absorber acceptor density of 1018 (cm−3). However, Fig. 14(d) shows that the lowest efficiency of 14.75% was found for Sb2S3 HTL and 1014 (cm−3) absorber acceptor density. On the other hand, the highest PCE value of 27.13% was achieved using Cu2Te HTL with an absorber acceptor density of 1018 (cm−3). Although Cu2Te HTL provided relatively high Vo, JSC, FF, and PCE in all cases, the highest efficiency was specifically obtained at the shallow acceptor density of 1018 (cm−3). For stable and efficient device performance, the shallow acceptor density should be maintained within an optimal range, avoiding values that are too low or excessively high.1,6,7,21 Our optimization study indicates that a shallow acceptor density of 1 × 1017 cm−3 yields the most favorable device response. Therefore, Cu2Te can be identified as the best HTL material based on absorber thickness optimization, where Vo = 0.752 V, JSC = 39.23 mA cm−2, FF = 84.43%, and the highest PCE = 24.92% are achieved when the absorber a shallow acceptor density of 1 × 1017 cm−3. Table 10 also includes more details. The effect of Cs3SCl absorber layer shallow acceptor density on (a) Vo, (b) JSC, (c) FF, and (d) PCE for different HTL-based anti-perovskite solar cells. Table 10Optimized photovoltaic performance of Cs3SCl-based solar cells with different etl materials following shallow acceptor density tuningStructure J SC (mA cm−2) V o (volts)FF (%)PCE (%)Absorber shallow acceptor density (cm−3)Al/FTO/SnS2/Cs3SCl/Cu2Te/Se39.230.75284.4324.921 × 1017Al/FTO/SnS2/Cs3SCl/Sb2S3/Se38.0010.74882.6523.521 × 1017Al/FTO/SnS2/Cs3SCl/CuO/Se38.3270.75184.0624.191 × 1017Al/FTO/SnS2/Cs3SCl/P3HT/Se38.5310.75384.4024.481 × 1017 Optimized photovoltaic performance of Cs3SCl-based solar cells with different etl materials following shallow acceptor density tuning Influence of temperature on photovoltaic performance parameters (JSC, Vo, PCE, and FF) of Cs3SCl absorber-based APSCs with various HTLs In this study, all simulations of the proposed solar cell structure shown in Fig. 8 were initially conducted at a temperature of 300 K (27 °C). Since solar cells operate outdoors, temperature variations can influence their performance, making it essential to investigate the impact of temperature on device behavior. In this study, different HTL materials were used, where SnS2 was adopted as the ETL and Al and Au were used as the front and back contact metals, respectively. In the proposed anti-perovskite solar cells, only the solar device temperature is changed stepwise from 280 K to 380 K, while keeping all other layer materials and physical parameters unchanged, so that its impact on device performance can be properly assessed. It can be clearly observed from Fig. 15(a)–(d) in the study that for all types of HTL materials used, the Vo, FF, and PCE all gradually decrease with increasing temperature of solar cell device except only for JSC, which very slightly increases. Among the tested HTL materials, the lowest Vo value of 0.534 V was obtained when using Sb2S3 with the solar cell device temperature at 380 K. On the other hand, the highest Vo value of 0.734 V was achieved when using Cu2Te HTL with the solar cell device temperature at 280 K. Next, Fig. 15(b) displays a different trend in the short-circuit current density (JSC), which is increased slightly. The Sb2S3 HTL with the solar cell device temperature at 280 K yielded the lowest JSC value of 38.38 mA cm−2, while the Cu2Te HTL with the solar cell device temperature at 380 K yielded the highest JSC value of 39.38 mA cm−2. After that, Fig. 15(c) shows that the lowest FF value of 74.08% was recorded for Sb2S3 HTL and 380 K solar cell device temperature. In contrast, the highest FF value of 84.37% was achieved using Cu2Te HTL with solar cell device temperature at 280 K. However, Fig. 15(d) shows that the lowest efficiency of 15.22% was found for Sb2S3 HTL and 380 K solar cell device temperature. On the other hand, the highest PCE value of 24.35% was achieved using Cu2Te HTL 380 K solar cell device temperature. Although Cu2Te HTL provided relatively high Vo, JSC, FF, and PCE in all cases, the highest efficiency was specifically obtained at 300 K temperature. For stable and efficient device performance, the solar cell device temperature should be maintained within an optimal range, avoiding values that are too low or excessively high.1,6,7,21 Our optimization study indicates that a 300 K temperature yields the most favorable device response. Therefore, Cu2Te can be identified as the best HTL material based on absorber thickness optimization, where Vo = 0.6959 V, JSC = 39.354 mA cm−2, FF = 82.96%, and the highest PCE = 22.72% are achieved when the solar cell device temperature is 300 K. Influence of temperature on (a) Vo, (b) JSC, (c) FF, and (d) PCE of Cs3SCl absorber–based anti-perovskite solar cells employing different HTL materials. Influence of back contact metal on photovoltaic performance parameters (JSC, Vo, PCE, and FF) of Cs3SCl absorber-based APSCs with various HTLs In this work, the influence of different back-contact metals and HTLs was investigated while employing SnS2 as the ETL and keeping all other device parameters unchanged. The back-contact metals considered include C, Au, W, Pd, Ni, Pt, Re, and Se, with corresponding work function values of 5, 5.1, 5.22, 5.3, 5.5, 5.65, 5.75, and 5.9 eV, respectively.21Fig. 16 illustrates the energy band alignment of these back-contact metals with respect to the Cs3SCl absorber and the CuO HTL layer. The optimization results for the back-contact metal are summarized in Fig. 17, where Cs3SCl is identified as the most promising absorber. Among the examined contacts, selenium (Se), possessing the highest work function (5.9 eV), delivers the best device performance. Under this optimized configuration, the Cs3SCl-based solar cell achieves maximum photovoltaic parameters, including an open-circuit voltage (Vo) of 0.6959 V, a short-circuit current density (JSC) of 39.354 mA cm−2, a peak power conversion efficiency (PCE) of 22.72%, and a high fill factor (FF) of 82.96%. Energy band alignment of the Cs3SCl absorber with various hole transport layers (HTLs) with several back-contact metal electrodes. Influence of back contact metal on (a) Vo, (b) JSC, (c) FF, and (d) PCE of Cs3SCl absorber–based anti-perovskite solar cells employing different HTL materials. Comparative discussion and growth mechanism of Cs3SCl anti-perovskite Table 11 presents a comparative analysis of the photovoltaic performance of the Cs3SCl-based device with previously reported solar cell structures. The proposed Al/FTO/SnS2/Cs3SCl/Cu2Te/Se configuration exhibits a power conversion efficiency (PCE) of 24.92%, with a relatively high short-circuit current density (JSC = 39.226 mA cm−2), moderate open-circuit voltage (VO = 0.752 V), and good fill factor (FF = 84.43%). Compared to previously reported devices, the present structure shows a notably higher JSC, which can be attributed to the relatively lower bandgap and enhanced light absorption. However, the Voc is comparatively lower than several reported systems, mainly due to the narrower effective bandgap used in the device simulation. As a result, although some devices demonstrate higher overall efficiency, they generally exhibit lower current density or rely on different absorber systems. Overall, the Cs3SCl-based device demonstrates competitive performance, particularly in terms of current generation, indicating its potential as a promising absorber material for photovoltaic applications. Table 11Photovoltaic performance comparison of Cs3SCl absorber–based APSCs with previous studiesConfiguration V o (volts)FF (%) J SC (mA cm−2)PCE (%)ReferenceAu/Spiro-OmeTAD/CIGS/MASnI3/CdS/ZnO/FTO1.3854.2448.2836.38 87 ITO/TiO2/NaZn0.7Cu0.3Br3/MASnI3/CuO/Au1.137782.1934.838932.58 88 SnS2/CsSn0.5Ge0.5I3/FASnI3/Zn3P2/Pt1.18589.5831.21833.16 89 AZO∕TiO2∕CsPbI3∕RbGeI3∕Ni1.0488.3834.7731.91 90 FTO/WO3/CsSnI3/CsSnGeI3/Cs3Sb2Br9/Cu2O/Au1.24489.1732.64036.21 91 FTO/n + -FASnI3/ETL/FASnI3/HTL1.100287.3331.42230.19 92 ITO/C60/MASnI3/RbGeI3/Cu2O/Au0.91465.4920.1932.7 93 ITO/ZnO/Cs2BiAgI6/CIGS/Spiro-OMeTAD/Au1.10885.0130.1031.89 94 Al/FTO/SnS2/Cs3SCl/Cu2Te/Se0.75284.4339.2324.92This workAl/FTO/SnS2/Na3SBr/CuO/Au1.54484.5120.8227.172 1 Al/FTO/SnS2/K3SeI/CuO/Se1.135582.8831.7129.84 20 Al/FTO/TiO2/Na3OI/CuO/Au1.476883.5027.6634.12 6 Al/FTO/WS2/Na3OBr/Cu2O/Se1.42382.2821.3825.045 7 Al/FTO/WS2/Cs3SBr/CuO/Se0.74684.7142.76427.05 21 Al/FTO/SnS2/K3SeBr/CuO/Se1.16488229.36328.02 28 Al/Na3SI/Se1.685190.8826.18940.11 2 Photovoltaic performance comparison of Cs3SCl absorber–based APSCs with previous studies Table 12 presents a comparative evaluation of the mechanical, optoelectronic, and dynamical properties of Cs3SCl with other reported anti-perovskite materials. The calculated bandgap of Cs3SCl (1.185 eV) is relatively lower than most of the compared compounds, indicating its suitability for enhanced light absorption in photovoltaic applications. In addition, Cs3SCl exhibits the highest electron affinity (4.53 eV), which is beneficial for efficient charge transfer and carrier extraction. The dielectric constant of Cs3SCl is slightly lower compared to several reported materials, suggesting moderate polarization behavior. However, its absorption coefficient in the UV–visible region remains comparable, confirming its capability for effective light harvesting. The carrier mobility values (µe and µh) are moderate and consistent with similar anti-perovskite systems, indicating balanced charge transport properties. Furthermore, all listed materials, including Cs3SCl, satisfy both phonon and mechanical stability criteria. The Pugh's ratio (B/G = 2.03) confirms the ductile nature of Cs3SCl, which is advantageous for structural reliability. Overall, the combined properties suggest that Cs3SCl offers a balanced performance in terms of stability, optical response, and charge transport, making it a promising candidate for photovoltaic and optoelectronic applications. Table 12A comparative study on the mechanical, optoelectronic, and dynamic attributes of Cs3SCl relative to previous researchStructureNa3SBrK3SeINa3OINa3OBrK3SeBrCs3SBrCs3SClBandgap (eV)2.53611.70472.011.87471.72681.1021.185Electron affinity (eV)3.573.7223.9573.4493.6653.9474.53Dielectric constant, ε1(0)2.622.0643.353.031.911.68231.628Light absorption capability (cm−1)(13 × 105 to 0.5 × 105) in the UV-to-visible-to-NIR region(6.8 × 105 to 0.5 × 105) in the UV-to-visible region(1.6 × 106 to 1 × 105) in the UV-to-visible region(1.5 × 106 to 0.74 × 105) in the UV-to-visible region(5 × 105 to 0.5 × 105) in the UV-to-visible region(2 × 105 to 0.5 × 105) in the UV-to-visible region(2.6 × 105 to 2.5 × 104) in the UV-to-visible regionMobility of hole, µh (cm2 V−1 s−1)31.238.5324.496.468.1711.511.5Mobility of electron, µe (cm2 V−1 s−1)55.1642.261.4380.238.732.630.3Phonon stabilityStableStableStableStableStableStableStableMechanical stabilityStableStableStableStableStableStableStablePugh's ratio1.81 (ductile)1.618 (brittle)1.29 (brittle)1.09 (brittle)1.923 (ductile)2.13 (ductile)2.03 (ductile)ApplicationOpto-electronic and solar cellPhotovoltaic, photo-catalysis, and opto-electronicPhotovoltaic and opto-electronicPhotovoltaic and opto-electronicPhoto-catalysis, opto-electronic, and solar cellPhotovoltaic, photo-catalysis, and opto-electronicPhotovoltaic, photo-catalysis, and opto-electronicReference 1 20 6 7 21 This workThis work A comparative study on the mechanical, optoelectronic, and dynamic attributes of Cs3SCl relative to previous research Although the present study is entirely based on first-principles DFT calculations, the obtained results strongly indicate that Cs3SCl is a physically viable and potentially synthesizable anti-perovskite compound. The optimized crystal structure confirms a stable cubic phase with Pm3̄m symmetry, while the absence of imaginary frequencies in the phonon dispersion spectrum verifies its dynamical stability. In addition, the calculated elastic constants satisfy the Born stability criteria, confirming the mechanical robustness of the material. Beyond structural stability, Cs3SCl exhibits promising optoelectronic properties, including a moderate bandgap, appreciable optical absorption in the UV–visible region, and balanced charge carrier mobility, which are essential for photovoltaic and optoelectronic applications. These combined characteristics suggest that the material possesses the fundamental requirements for functional device performance. Importantly, previously reported studies on anti-perovskite systems provide strong evidence supporting the experimental feasibility of this class of materials. For example, alkali-metal-based anti-perovskites such as Na3OX (X = Cl, Br, I, BH4) have been successfully synthesized and characterized, demonstrating their practical viability.95 Similarly, Ca3MN-type anti-perovskites (M = As, P, Sb, Ge, Bi, Pb, Sn) have been experimentally realized with confirmed structural stability.96 Furthermore, the successful preparation of nitride-based anti-perovskites, such as Mg3AsN, highlights the flexibility and realizability of these systems.97 These experimental advancements strongly suggest that related compounds, including Cs3SCl, are likely to be synthesizable under appropriate conditions. However, it is worth noting that halide-containing materials may face stability challenges under ambient environmental conditions, which may require suitable encapsulation strategies for practical applications. Overall, this work provides a comprehensive theoretical foundation for Cs3SCl, confirming its stability and highlighting its strong potential for future experimental realization and applications in photovoltaic and optoelectronic technologies. Conclusions In this work, a comprehensive first-principles investigation of the lead-free anti-perovskite Cs3SCl compound was performed to assess its suitability for photovoltaic and optoelectronic applications. The DFT-based calculations confirmed that Cs3SCl is structurally, mechanically, and dynamically stable, highlighting its feasibility for practical device implementation. Electronic structure analysis revealed a direct bandgap semiconductor with bandgap values of 1.185 eV (GGA-PBE) and 2.051 eV (HSE06) at the Γ-point, indicating favorable characteristics for efficient solar energy harvesting and visible-light absorption. The optical study demonstrated strong absorption in visible-light wavelength region, with absorption coefficients reaching ∼2.5 × 104 cm−1, together with suitable reflection and dielectric responses. These characteristics suggest that Cs3SCl can serve as an efficient light-harvesting material for advanced photovoltaic and optoelectronic technologies. To evaluate its device-level applicability, a lead-free and environmentally friendly solar cell based on Cs3SCl was designed and optimized using SCAPS-1D simulations. Various hole transport layers, back-contact metals, absorber thicknesses, defect densities, and doping concentrations were systematically examined. Among all investigated configurations, the Al/FTO/SnS2/Cs3SCl/Cu2Te/Se device exhibited the best photovoltaic performance, delivering a VO of 0.752 V, JSC of 39.23 mA cm−2, FF of 84.43%, and a maximum PCE of 24.92%. Optimal performance was achieved with an absorber thickness of 0.750 µm, a defect density of 1 × 1015 cm−3, and a shallow acceptor density of 1 × 1017 cm−3. The device also showed an extended photoresponse from 300 to 1200 nm and an EQE exceeding 98.56% within the 350–900 nm range. It should be noted that the achieved PCE of 24.92% represents an optimized simulation result under ideal conditions. While practical implementation may yield lower efficiency due to material and interface limitations, the results demonstrate the strong potential of Cs3SCl-based anti-perovskite solar cells for high-performance photovoltaic applications. Overall, the excellent stability, favorable electronic structure, strong optical absorption, and outstanding simulated photovoltaic performance establish Cs3SCl as a highly promising anti-perovskite absorber material. Considering the abundance, low cost, and non-toxic nature of its constituent elements, Cs3SCl represents a sustainable candidate for future high-efficiency solar cells and environmentally friendly optoelectronic technologies. Ethical approval The manuscript's authors agree that there is no research involving human participants, human data or tissue, or animal subjects. Author contributions Md. Earshad Ali: data curation, conceptualization, formal analysis, methodology, investigation, resources, software, validation, visualization, writing – original draft, Writing – review and editing, project administration, supervision. Anis Attour: formal analysis, investigation, methodology, resources, writing – review and editing, software, visualization, writing – original draft, funding acquisition, Md. Nobiul Islam: investigation, formal analysis, resources, software, conceptualization, visualization, methodology, writing – original draft, Writing – review and editing, Karim Kriaa: conceptualization, formal analysis, investigation, software, validation, visualization, writing – original draft, writing – review and editing, funding acquisition, Md. Azizur Rahman: investigation, validation, software, formal analysis, data curation, writing – original draft, writing – review and editing, S. AlFaify: formal analysis, investigation, methodology, resources, writing – review and editing, software, visualization, writing – original draft, funding acquisition, Noureddine Elboughdiri: conceptualization, formal analysis, investigation, software, validation, visualization, writing – original draft, writing – review and editing, funding acquisition. Conflicts of interest The authors have no conflicts of interest. Funding This work was supported and funded by the Deanship of Scientific Research at Imam Mohammad Ibn Saud Islamic University (IMSIU) (grant number IMSIU-DDRSP2602).