Seismic attributes analysis and petrophysical modeling for reservoir characterization and prospect identification in the I/R oil fields, Murzuq Basin, Libya Authors: Adel Mahmoud Negm, Dhyaa H. Haddad, Mohamed I. Abdel-Fattah, Hamzah S. Amir, Mohammed A. Amir, Moataz Kh. Barakat, Mohamed Reda Published: 2026 ABSTRACT The Upper Ordovician Mamuniyat Formation represents the principal hydrocarbon reservoir in the I/R oil fields, Murzuq Basin, Libya, where reservoir quality and distribution are strongly influenced by glacial depositional processes and structural complexity. This study presents an integrated reservoir characterization workflow combining multi-well petrophysical analysis, 3D seismic interpretation, seismic attribute analysis (variance, RMS amplitude, and energy), spectral decomposition, and 3D static reservoir modeling. Petrophysical evaluation from eleven wells indicates that the reservoir is dominated by quartz-rich sandstones with shale volume generally < 25%, effective porosity ranging from ~ 12 to 15%, and water saturation varying between ~ 20 and 55%. Seismic attribute analysis reveals a dominant NW–SE-trending fault system controlling reservoir compartmentalization, while amplitude-based attributes delineate sand-prone fairways associated with improved reservoir quality. Spectral decomposition further enhances imaging of channelized depositional elements and demonstrates lateral continuity of reservoir bodies. The integration of seismic-derived indicators with petrophysical properties within a 3D modeling framework identifies zones of enhanced reservoir quality concentrated in the central, northwestern, and southwestern parts of the field. Two new prospective zones are delineated on the upthrown side of the main fault, characterized by favorable seismic responses, higher porosity, and reduced water saturation. Blind well validation confirms good agreement between modeled and observed properties, demonstrating the predictive capability of the approach. Compared to previous studies relying on isolated datasets, this integrated workflow provides a more quantitative and spatially consistent characterization of reservoir heterogeneity, significantly reducing uncertainty and supporting improved exploration and development strategies in structurally complex clastic systems. Introduction The Murzuq Basin of southwestern Libya is one of the most important Paleozoic hydrocarbon provinces in North Africa (Fig. 1), hosting several giant oil fields and contributing significantly to Libya’s oil production1–3. Exploration activities in the basin began in the 1950s and intensified following the discovery of commercially productive Paleozoic reservoirs, particularly those of Ordovician age4–6. Among these, the Upper Ordovician Mamuniyat Formation represents the primary reservoir unit in many fields, including the I/R oil fields located in the eastern Murzuq Basin (Fig. 1a). The I/R fields lie within both the NC-115 and NC-186 blocks within the Sharara petroleum system and cover an area of approximately 250 km² (Fig. 1b). Development of the field started in 2008, and current production is about 37,000 barrels of oil per day, with an estimated stock tank original oil in place approaching one billion barrels, highlighting the strategic importance of this reservoir. Fig. 1(a) Regional location map showing the Murzuq Basin in southwestern Libya and the position of the I/R oil field within the Sharara field area; the inset highlights the NC115 and NC186 concession blocks. (b) Base map of the study area illustrating the distribution of wells used in this study within the I/R field. Maps were generated using Surfer software version 16.6 (Golden Software Surfer; https://www.goldensoftware.com/products/surfer/). (a) Regional location map showing the Murzuq Basin in southwestern Libya and the position of the I/R oil field within the Sharara field area; the inset highlights the NC115 and NC186 concession blocks. (b) Base map of the study area illustrating the distribution of wells used in this study within the I/R field. Maps were generated using Surfer software version 16.6 (Golden Software Surfer; https://www.goldensoftware.com/products/surfer/). Despite its economic significance, the Mamuniyat Formation exhibits pronounced lateral and vertical heterogeneity in reservoir quality across the I/R fields7. Variations in porosity, permeability, and net pay thickness are observed both between wells and within individual wells, where the most favorable reservoir properties may occur in the lower or upper parts of the formation. This heterogeneity is largely attributed to the complex depositional history of the Mamuniyat Formation, which was deposited during the Late Ordovician glacial cycle and is characterized by glaciomarine to shallow marine environments7–9. The reservoir is dominated by quartz-rich sandstones interbedded with shale and siltstone, commonly arranged in channelized and incised valley-fill geometries. These sand bodies are frequently stacked, truncated, or eroded by younger depositional units, leading to uncertainties in reservoir connectivity and fluid flow behavior10,11. Previous studies in the Murzuq Basin have addressed the stratigraphy, sedimentology, and petroleum system elements of the Mamuniyat Formation7,12; however, most previous studies relied on either well-based petrophysical analysis or conventional seismic interpretation alone. A clear gap remains in the lack of integrated studies that quantitatively combine multi-well petrophysical data with advanced seismic attributes and 3D reservoir modeling to constrain reservoir heterogeneity and connectivity13–16. Therefore, this study aims to provide an integrated reservoir characterization of the Mamuniyat Formation in the I/R oil fields through the combination of petrophysical analysis, seismic attribute evaluation, and 3D static modeling. Well log data from eleven wells were used to quantify key petrophysical parameters, while 3D seismic data were analyzed using variance, RMS amplitude, energy attributes, and spectral decomposition techniques to delineate structural features, facies distribution, and potential hydrocarbon accumulations. Although integrated workflows combining seismic attributes, spectral decomposition, and 3D reservoir modeling are well established in reservoir characterization, their application within the Mamuniyat Formation of the I/R oil fields remains limited. In particular, few studies have quantitatively integrated multi-well petrophysical analysis with advanced seismic attribute interpretation and 3D static modeling to address reservoir heterogeneity and prospect delineation in this basin. The integration of these datasets aims to improve understanding of reservoir quality controls, reduce uncertainty in reservoir models, and identify new prospective areas that may enhance future exploration and development strategies in the I/R fields. Geological background The I/R oil fields is situated in the eastern Murzuq Basin, southwestern Libya, within the broader Sharara petroleum province (Fig. 1a). The Murzuq Basin is a large intracratonic basin that contains a thick Paleozoic sedimentary succession and hosts several prolific hydrocarbon systems, making it one of the most important petroleum provinces in North Africa4,5,7. Structurally, The Murzuq Basin is a large intracratonic basin characterized by a relatively simple structural framework dominated by broad basement-controlled arches and gentle synclinal depressions formed during Paleozoic subsidence. Its structural evolution is influenced by inherited Precambrian basement trends and later reactivation of major fault systems, which locally control trap development and reservoir compartmentalization17. The stratigraphic framework relevant to this study extends from the Cambrian through the Silurian, as summarized in the regional stratigraphic column (Fig. 2a). The older Cambrian to Middle Ordovician intervals (Hasawnah to Hawaz formations) generally represent pre-glacial, shallow-marine deposits, whereas the Upper Ordovician succession (Melaz Shuqran and Mamuniyat formations) is commonly interpreted to reflect glacial to glaciomarine sedimentation associated with the Late Ordovician icehouse event that affected large parts of North Africa8,9. The uppermost Silurian Tanezzuft Formation marks the waning of glacial conditions and the transition to post-glacial marine deposition, and it is regionally significant as an organic-rich “hot shale” interval in many parts of North Africa5. Fig. 2(a) Regional stratigraphic column of the NC115 concession in the Murzuq Basin showing the main lithostratigraphic units and major tectono-stratigraphic events affecting the basin71. (b) Synthetic seismogram generated (Petrel software) for well I-1 illustrating the well-to-seismic tie and correlation between log-derived reflectivity and seismic data within the Mamuniyat reservoir interval. (a) Regional stratigraphic column of the NC115 concession in the Murzuq Basin showing the main lithostratigraphic units and major tectono-stratigraphic events affecting the basin71. (b) Synthetic seismogram generated (Petrel software) for well I-1 illustrating the well-to-seismic tie and correlation between log-derived reflectivity and seismic data within the Mamuniyat reservoir interval. Within this stratigraphic context, the Mamuniyat Formation represents the principal reservoir unit in the I/R fields and is positioned as a sand-prone package between the Melaz Shuqran Formation below and the discontinuous Bir Tlacsin Formation above, or locally the Silurian Tanezzuft Formation where the Bir Tlacsin is absent5,18. The nature of the lower contact remains debated: Davidson et al. (2000) suggested a transitional relationship between the Melaz Shuqran and Mamuniyat formations, whereas Hallett and Clark-Lowes (2002) interpreted the boundary as unconformable, reflecting erosion and/or non-deposition linked to glacial dynamics. The upper boundary of the Mamuniyat Formation is commonly described as unconformable, with either the Bir Tlacsin or the Tanezzuft Formation overlying it, consistent with regional stratigraphic breaks tied to changes in ice volume and subsequent marine transgression. Sequence-stratigraphic interpretation indicates that the Upper Ordovician glacial cycle comprises three formations—Melaz Shuqran, Mamuniyat, and Bir Tlacsin—organized into three sequences bounded by glacial erosion surfaces (GES) (Fig. 3a–d). The first sequence (Melaz Shuqran) is interpreted as a glacial retreat systems tract bounded by GES1 and GES2. The second sequence corresponds to the Mamuniyat Formation and is bounded by GES2 and GES3; it includes a glacial retreat tract (Lower–Middle Mamuniyat) and a glacial minimum tract (Upper Mamuniyat), separated by a glacial maximum retreat surface (GMRS). The third (youngest) sequence is retrogradational and reflects a regional transgression and flooding of the area8. This glacially influenced stratigraphic architecture helps explain the strong heterogeneity of the Mamuniyat reservoir, where sand-rich bodies may occur as stacked and channelized elements with variable continuity, directly impacting reservoir quality distribution and connectivity at field scale (Fig. 3). Fig. 3(a) North–south seismic section through the I/R oil field flattened on the base Tanezzuft horizon, showing interpreted sequence stratigraphic surfaces, system tracts, cycles, and lithostratigraphic units of the Upper Ordovician succession. (b) Corresponding seismic section highlighting the distribution of the Melaz Shuqran, Mamuniyat, and Bir Tlacsin formations. (c) Conceptual sketch illustrating the sequence stratigraphic framework and key glacial erosion surfaces (GES) and glacial maximum retreat surface (GMRS). (d) Simplified lithostratigraphic sketch summarizing the vertical and lateral relationships of the Upper Ordovician formations within the I/R field. This section was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). (a) North–south seismic section through the I/R oil field flattened on the base Tanezzuft horizon, showing interpreted sequence stratigraphic surfaces, system tracts, cycles, and lithostratigraphic units of the Upper Ordovician succession. (b) Corresponding seismic section highlighting the distribution of the Melaz Shuqran, Mamuniyat, and Bir Tlacsin formations. (c) Conceptual sketch illustrating the sequence stratigraphic framework and key glacial erosion surfaces (GES) and glacial maximum retreat surface (GMRS). (d) Simplified lithostratigraphic sketch summarizing the vertical and lateral relationships of the Upper Ordovician formations within the I/R field. This section was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Materials and methods This study integrates well log analysis, 3D seismic interpretation, seismic attribute analysis, spectral decomposition, and three-dimensional static reservoir modeling to characterize the Upper Ordovician Mamuniyat Formation in the I/R oil fields, Murzuq Basin, Libya (Fig. 4). The database includes wireline logs from eleven wells and a post-stack 3D seismic volume covering the entire fields. The well log suite comprises gamma ray, density, neutron porosity, compressional sonic, photoelectric and deep resistivity, which were used for lithological discrimination and petrophysical evaluation. All logs were subjected to quality control, including depth matching, normalization, and removal of anomalous readings. Shale volume was calculated from gamma ray log analysis using Eq. (1)19. Fig. 4Integrated workflow combining seismic interpretation, attribute analysis, petrophysical evaluation, and 3D modeling for reservoir characterization of the Mamuniyat Formation in the I/R Oil Fields, Murzuq Basin, Libya. Integrated workflow combining seismic interpretation, attribute analysis, petrophysical evaluation, and 3D modeling for reservoir characterization of the Mamuniyat Formation in the I/R Oil Fields, Murzuq Basin, Libya. 1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{V}}_{{{\mathrm{sh}}}} = \frac{{{\mathrm{GR}} - {\mathrm{GR}}_{{{\mathrm{matrix}}}} }}{{{\mathrm{GR}}_{{{\mathrm{shale}}}} - {\mathrm{GR}}_{{{\mathrm{matrix}}}} }}$$\end{document} The gamma ray (GR) log measures natural radioactivity. GRmin is the minimum value in clean sand (after corrections), and GRmax is the maximum value in adjacent shale. Following19, total porosity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\varnothing}}_{\mathbf{T}}$$\end{document}) and effective porosity (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\varnothing}}_{\mathrm{e}}$$\end{document}) were calculated from neutron-density logs using the following formula:2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\emptyset _{{\mathbf{T}}} = {\mathrm{~}}\frac{{\emptyset _{{{\mathbf{N}}{\mathrm{~}}}} + {\mathrm{~}}\emptyset _{{\mathbf{D}}} }}{2}$$\end{document}3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\emptyset _{{\mathrm{e}}} = {\mathrm{~}}\emptyset _{{{\mathrm{T~}}}} \times \left( {1 - {\mathrm{V}}_{{{\mathrm{sh}}}} } \right) \times 100$$\end{document} where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\varnothing}}_{\mathbf{T}}$$\end{document} is total porosity, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\varnothing}}_{\mathbf{N}\:}$$\end{document} is neutron porosity, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\varnothing}}_{\mathbf{D}}$$\end{document} is density porosity, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\varnothing}}_{\mathrm{e}}$$\end{document} is effective porosity, and Vsh is shale volume. Water saturation was assessed using the “Indonesia” model20. This model was developed for use in shaly sand reservoirs.4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{1}{{{\mathrm{R}}_{{\mathrm{t}}} }} = {\mathrm{S}}_{{\mathrm{w}}}^{{{\mathrm{n}}/2}} \left[ {\frac{{{\mathrm{V}}_{{{\mathrm{sh}}}}^{{1 - {\mathrm{V}}_{{{\mathrm{sh}}}} /2}} }}{{\sqrt {{\mathrm{R}}_{{{\mathrm{sh}}}} } }} + \frac{{{{\O }}_{{\mathrm{e}}}^{{{\mathrm{m}}/2}} }}{{\sqrt {{\mathrm{a}}R_{{\mathrm{w}}} } }}} \right]^{2}$$\end{document} Sw is water saturation, a is the tortuosity factor, Rw is formation water resistivity, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{\varnothing}$$\end{document} is porosity, m is the cementation exponent, n is the saturation exponent, Rt is true formation resistivity, Rsh is shale resistivity. The seismic data were also quality-checked to ensure adequate signal continuity, frequency content, and resolution within the Mamuniyat reservoir interval prior to interpretation. The 3D seismic dataset used in this study is a post-stack time-migrated volume covering the I/R oil fields, acquired with a bin size of ~ 25 × 25 m, a sampling interval of 2 ms, and a record length of ~ 4–5 s. The processing workflow included amplitude recovery, noise attenuation, deconvolution, velocity analysis, NMO correction, stacking, and post-stack time migration, followed by frequency filtering to enhance data quality. Spectral analysis indicates a dominant frequency of ~ 50–60 Hz within the Mamuniyat interval, corresponding to a vertical resolution of ~ 10–15 m. The seismic data exhibit a high signal-to-noise ratio, as evidenced by clear reflector continuity and well-defined fault patterns, ensuring reliable seismic interpretation and attribute analysis. Well-to-seismic ties were performed by generating synthetic seismograms using a Ricker wavelet to accurately correlate well logs with seismic reflections (Fig. 2b). The used wavelet is shown as a zero-phase, symmetrical pulse centered at 0 ms. This indicates it is a standard; theoretical wavelet often used as a starting point for matching seismic data to synthetic seismograms. Three main horizons—the Silurian Tanezzuft “hot shale,” the top of the Mamuniyat Formation, and the top of the Melaz Shuqran Formation—were interpreted to establish the structural and stratigraphic framework. Faults affecting the reservoir were mapped using conventional seismic interpretation supported by structural attributes. Petrophysical analysis involved estimating shale volume from gamma-ray logs, deriving total and effective porosity from density–neutron responses, and calculating water saturation using the Indonesian equation due to the presence of shale within the formation provides more reliable estimates of water saturation. with formation-specific parameters obtained from Pickett plot analysis21. Cross-plot techniques, including bulk density versus photoelectric effect (PEF) and M–N plots, were applied to refine lithological classification into sandstone, shaly sandstone, and shale facies. The M and N parameters were calculated from porosity logs (density-neutron-sonic) using the following equations22:5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{M}} = \frac{{{{\Delta t}}_{{{\mathrm{fl}}}} - {{\Delta t}}_{{{{log}}}} }}{{{{\rho }}_{{\mathrm{b}}} - {{\rho }}_{{{\mathrm{fl}}}} }} \times 0.01$$\end{document}6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{N}} = \frac{{\emptyset _{{{\mathrm{Nfl}}}} - \emptyset _{{{\mathrm{Nlog}}}} }}{{{{\rho }}_{{\mathrm{b}}} - {{\rho }}_{{{\mathrm{fl}}}} }}$$\end{document} where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{\Delta\:}{\mathrm{t}}_{\mathrm{f}\mathrm{l}}$$\end{document} represents the transit fluid time, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{\Delta\:}{\mathrm{t}}_{\mathrm{l}\mathrm{o}\mathrm{g}}$$\end{document} denotes the transit time of the formation inside the interval, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\uprho\:}}_{\mathrm{f}\mathrm{l}}$$\end{document} represents fluid density, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\uprho\:}}_{\mathrm{b}}$$\end{document} signifies formation bulk density, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\varnothing}}_{\mathrm{N}\mathrm{f}\mathrm{l}}$$\end{document} indicates neutron porosity for fluid, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\varnothing}}_{\mathrm{N}\mathrm{l}\mathrm{o}\mathrm{g}}$$\end{document} refers to neutron porosity of the formation. Seismic attribute analysis was applied to enhance reservoir characterization and prospect identification. Variance attributes were used to delineate faults and stratigraphic discontinuities23–33, while amplitude-based attributes such as root mean square (RMS) amplitude and energy were computed to highlight lithological variations and potential hydrocarbon indicators34–37. When dealing with seismic data, the Root Mean Square (RMS) amplitude is a critical measurement used to understand the average energy content of a seismic trace within a specific time window. the RMS calculation squares the values to ensure all energy is accounted for. The RMS Formula For a discrete seismic trace consisting of n samples, The RMS Formula For a discrete seismic trace consisting of n samples, the RMS amplitude is calculated as follow.7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{A}}_{{{\mathrm{rms}}}} = \frac{1}{{\mathrm{n}}}\mathop \sum \limits_{{{\mathrm{i}} = 1}}^{{\mathrm{n}}} {\mathrm{a}}_{{\mathrm{i}}}^{2}$$\end{document} Where: n = The number of samples in the analysis window. a.i. = The amplitude value of the i-th sample. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\sum\:`\mathrm{a}$$\end{document}= The sum of the squares of all amplitude values in the window. Because seismic waves are essentially oscillations, squaring the amplitude relates directly to the energy or intensity of the wave. So, the RMS amplitude consider Direct Hydrocarbon Indicators (DHI), High RMS amplitude anomalies (often called “bright spots”) can indicate changes in lithology or the presence of fluids like gas or oil. The Energy attribute at the coordinates (x, y, t) is defined as the sum of squared amplitudes within a specified time window36. It is mathematically expressed as:8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$E = \mathop \sum \limits_{{\tau = t1}}^{{t2}} u\left( {x,y,t + \tau } \right)2$$\end{document} Where t1 and t2 represent the relative start and end times of the energy analysis window. Spectral decomposition was performed to analyze frequency-dependent seismic responses and to improve imaging of depositional features such as channels and incised valley fills. there are several ways to visualize spectral attributes. One effective method is to represent sub-spectral data using an RGB display. By defining three specific basis functions—corresponding to the red, green, and blue color as the following38–44.9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$bR\left( f \right) = 0.56~ \cdot \left( {1 + \cos \left( {\pi \frac{{f - fR}}{{K \cdot fBandwidth}}} \right)} \right)$$\end{document}10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$bG\left( f \right) = 0.56~ \cdot \left( {1 + \cos \left( {\pi \frac{{f - fG}}{{K \cdot fBandwidth}}} \right)} \right)$$\end{document}11\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$bB\left( f \right) = 0.56~ \cdot \left( {1 + \cos \left( {\pi \frac{{f - fB}}{{K \cdot fBandwidth}}} \right)} \right)$$\end{document} Finally, all interpreted horizons, faults, facies, and petrophysical properties were integrated into a 3D static reservoir model, in which facies and property distributions were populated using geostatistical methods to evaluate reservoir quality distribution and identify prospective zones within the Mamuniyat Formation45–53. The 3D geostatistical modeling workflow was implemented to ensure reproducibility and consistency in representing reservoir heterogeneity. Facies modeling was performed using sequential indicator simulation (SIS), conditioned to well data and guided by the structural framework and interpreted depositional trends. Petrophysical properties, including effective porosity and water saturation, were modeled using sequential Gaussian simulation (SGS) after normal-score transformation of the input data. Variogram analysis was conducted to define spatial continuity in the vertical and horizontal directions, with parameters calibrated from well data and aligned with geological trends. Prior to modeling, well logs were upscaled to the simulation grid to ensure compatibility between data resolution and grid cell size. The modeling process was fully conditioned to well control, ensuring that simulated values honor measured data while capturing realistic spatial variability across the reservoir. Results and discussion Seismic attributes analysis Variance attribute: fault detection and reservoir compartmentalization The interpretation of the 3D seismic volume, supported by attribute analysis, provides critical insights into the structural framework and its influence on reservoir distribution in the I/R oil fields. The Mamuniyat Formation is affected by a dominant fault system trending NW–SE, accompanied by subordinate fault splays that locally segment the reservoir and may create structural compartments and variable connectivity (Figs. 3a–d and 5). This structural architecture is consistent with the established role of coherence/variance-type attributes in highlighting discontinuities and subtle fault offsets in seismic data, particularly where reflector continuity is otherwise strong23,25,40,54–57. Fig. 5Seismic variance attribute analysis of the I/R oil field showing the structural framework affecting the Mamuniyat Formation: (a1–a3) variance attribute time slices at different levels within the Mamuniyat interval highlighting faults and discontinuities; (b1, b2) representative seismic sections illustrating the main fault controlling reservoir distribution and compartmentalization; (c) integrated map of interpreted faults and structural features affecting the Mamuniyat reservoir across the study area. Maps were generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Seismic variance attribute analysis of the I/R oil field showing the structural framework affecting the Mamuniyat Formation: (a1–a3) variance attribute time slices at different levels within the Mamuniyat interval highlighting faults and discontinuities; (b1, b2) representative seismic sections illustrating the main fault controlling reservoir distribution and compartmentalization; (c) integrated map of interpreted faults and structural features affecting the Mamuniyat reservoir across the study area. Maps were generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Variance (coherency) attribute slices extracted at multiple time levels within the Mamuniyat interval reveal a clear network of discontinuities expressed as linear to curvilinear features (Fig. 5a1–a3). These discontinuities correspond to fault and fracture zones that can affect reservoir performance and drilling outcomes by controlling lateral sealing, creating compartments, or enhancing permeability along damage zones. The seismic sections confirm that the most prospective Mamuniyat reservoir interval is structurally controlled by the main fault that bounds the study area, with the best-developed reservoir appearing on the upthrown side where reservoir sands are better preserved and structurally positioned (Fig. 5b1,b2). The grouped extraction of faults (Fig. 5c) emphasizes that both major and minor faults share a coherent structural grain, and collectively they define the primary trapping style and compartmentalization pattern of the field. Similar outcomes have been documented in attribute-driven fault imaging studies, where variance improves detection of smaller-scale discontinuities that are difficult to map using conventional interpretation alone58–60. From a reservoir standpoint, the mapped fault framework provides two key implications. First, the main fault likely defines the largest structural closure and boundary conditions for hydrocarbon accumulation. Second, the subsidiary faults may either subdivide the reservoir into compartments (reducing lateral connectivity) or locally enhance permeability where fault damage zones intersect sand-prone facies. In practice, this explains why wells within the same structural sector can display different performance or petrophysical signatures depending on their proximity to fault zones and facies architecture (Figs. 1b and 5d). Amplitude-based attributes: reservoir distribution and prospectivity Amplitude-based attributes were generated on or around the interpreted Mamuniyat horizon to delineate reservoir distribution and identify anomalous zones potentially related to lithology and/or hydrocarbon presence. RMS amplitude and energy are among the most widely used attributes for highlighting changes in reflectivity strength that may reflect sand–shale contrasts, porosity variations, or fluid effects23,35. In this study, both attributes consistently identify an area of enhanced seismic response in the western to central part of the field, suggesting a prospective fairway aligned with the structural framework and supported by petrophysical and modeling results (Fig. 6). Fig. 6Seismic amplitude attributes applied to the Mamuniyat Formation in the I/R oil field: (a) RMS amplitude map highlighting zones of high seismic response associated with sand-prone and prospective reservoir fairways; (b–d) energy attribute maps extracted at different time levels within the Mamuniyat interval showing lateral variations in seismic energy and delineating areas of enhanced reservoir potential. They were generated using OpendTect 7 software (dGB Earth Sciences B.V.). Seismic amplitude attributes applied to the Mamuniyat Formation in the I/R oil field: (a) RMS amplitude map highlighting zones of high seismic response associated with sand-prone and prospective reservoir fairways; (b–d) energy attribute maps extracted at different time levels within the Mamuniyat interval showing lateral variations in seismic energy and delineating areas of enhanced reservoir potential. They were generated using OpendTect 7 software (dGB Earth Sciences B.V.). The RMS amplitude map extracted over the Mamuniyat interval shows distinct high-amplitude zones (yellow–red colors) that correspond to areas of stronger reflectivity within the reservoir package (Fig. 6a). These anomalies can arise due to increased acoustic impedance contrast between reservoir sands and surrounding shales, local thickening of sand bodies, or changes in pore-fluid properties that produce direct hydrocarbon indicators (DHI). The RMS response is particularly useful because it “gains up” coherent reflection strength while suppressing random noise, improving the visibility of laterally continuous amplitude anomalies23. A key observation is that the RMS high-amplitude belt is not uniformly distributed across the field; instead, it shows clustering in structurally favorable positions and in zones interpreted to contain sand-dominated facies. This pattern supports the interpretation that the Mamuniyat reservoir is heterogeneous and channelized, with discrete sand bodies that may form stratigraphic–structural traps5. Importantly, the RMS anomaly coincides with the location of the proposed new prospect area, as later verified by energy attribute and spectral decomposition (Fig. 6a). The energy attribute, defined as the sum of squared amplitudes within a specified time window, provides an additional measure of seismic “strength” that may correlate with reservoir presence and quality36. Energy slices across three-time levels show that most wells are located within high-energy zones, while selected wells (e.g., R6 and R7) are situated outside the strongest anomalies (Fig. 6b–d). The energy attribute highlights a pronounced high-energy area in the western–central portion of the field, consistent with RMS amplitude results and supporting the hypothesis that this zone represents a sand-prone and potentially hydrocarbon-charged fairway (Fig. 6). The agreement between RMS and energy strengthens confidence that the anomaly is not an artifact of processing or noise but rather reflects a persistent subsurface property contrast. From an interpretation perspective, the convergence of RMS and energy anomalies suggests that (i) the Mamuniyat sands may be thicker and/or cleaner in the anomaly zone, (ii) porosity may be enhanced, and/or (iii) hydrocarbon saturation may contribute to amplitude strengthening. While amplitude anomalies can be non-unique, the subsequent integration with spectral decomposition and petrophysical modeling provides a stronger geological justification for prospect interpretation. Spectral decomposition: depositional elements and prospect fairways Spectral decomposition was applied to extract time–frequency information from the seismic volume and to improve visualization of stratigraphic features such as channels and sand fairways within the Mamuniyat interval. The method evaluates changes in amplitude as a function of frequency and phase, generating frequency-specific seismic volumes that can reveal thin-bed tuning, lateral thickness variations, and geomorphologic patterns35,38,39. This approach is particularly valuable for the Mamuniyat Formation because it is interpreted as a sand-prone interval with channelized geometry and stacked depositional elements, where thickness and facies variations may occur over short distances5,8. Amplitude spectrum analysis indicates that the dominant frequency of the seismic data in the study is approximately 54 Hz (Fig. 7a–c). Six frequency slices across a broad range (low to high frequencies) were generated in (Fig. 8) allowing the interpreter to test which frequency bands best illuminate stratigraphic variability in the Mamuniyat interval. to It visualizes the relationship between the frequency f (in Hz) and the wavenumber k (in m-1) for a wave field we used F/K filter (Fig. 7c), The vertical axis represents Frequency (f) ranging from 0 to over 200 Hz and the horizontal axis represents Wavenumber (k) ranging from − 0.04 to 0.0 m-1. Fig. 7Seismic frequency characteristics of the study area: (a) 3D seismic volume illustrating the reservoir interval used for spectral analysis; (b) amplitude spectrum of the full seismic dataset showing the dominant frequency content; (c) representative amplitude spectrum within the Mamuniyat Formation highlighting the frequency range used for spectral decomposition. It was generated using OpendTect 7 software (https://www.dgbes.com/software/opendtect). Seismic frequency characteristics of the study area: (a) 3D seismic volume illustrating the reservoir interval used for spectral analysis; (b) amplitude spectrum of the full seismic dataset showing the dominant frequency content; (c) representative amplitude spectrum within the Mamuniyat Formation highlighting the frequency range used for spectral decomposition. It was generated using OpendTect 7 software (https://www.dgbes.com/software/opendtect). Fig. 8Spectral decomposition time slices of the Mamuniyat Formation at different discrete frequencies, illustrating frequency-dependent amplitude variations and highlighting lateral changes in reservoir thickness and depositional architecture within the study area. They were generated using OpendTect 7 software (https://www.dgbes.com/software/opendtect). Spectral decomposition time slices of the Mamuniyat Formation at different discrete frequencies, illustrating frequency-dependent amplitude variations and highlighting lateral changes in reservoir thickness and depositional architecture within the study area. They were generated using OpendTect 7 software (https://www.dgbes.com/software/opendtect). The colored, textured area in the center represents the spectral energy density. The intense red/white colors indicate the dominant frequency and wavenumber components where most of the wave energy is concentrated. The V-shape (Black Lines): These lines indicate the linear relationship between frequency and wavenumber, defined by the equation:12\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\mathrm{f}=\mathrm{c}\:.\left[\mathrm{k}\right]$$\end{document} Where c represents the phase velocity of the wave. By calculating the slope of these lines (c = f/k), you can determine the propagation velocity of the waves. The concentration of energy at the center indicates that the wave field is dominated by low-wavenumber (long wavelength) components across a range of frequencies, likely centered around 50–70 Hz. The fact that the energy sits mostly within the bounds of those black lines suggests that the wave propagation is largely consistent with the velocity defined by the slopes of those lines. On the other hand, Fig. 7 show that different frequencies emphasize different aspects of geology. By viewing the same area at different frequencies ranging from 5 Hz to 75 Hz. As the frequency increases from 5 Hz to 25 Hz, we see a clear change in the “connectedness” of the geological features .at 5 Hz The feature indicated by the arrow appears as a solid, connected part. Low frequencies often illuminate large-scale geological bodies or thicker sedimentary layers. At 25 Hz, the high-resolution view shows the features as completely disconnected. This suggests that what looks like a single body at low resolution is actually a series of smaller, separate geological compartments or faulted blocks. The boxes highlight how specific geological “sweet spots” respond to different frequencies.at 40 Hz Shows a strong response in the boxed area (low to medium frequency), potentially indicating a specific thickness of a rock layer that “tunes” at this frequency. Where at 50 Hz & 75 Hz The signal in the boxed area fades or becomes more chaotic This indicates that the thinner or more complex parts of the reservoir are better resolved at 40 Hz, while higher frequencies may be picking up more “noise” or very fine-scale heterogeneities. So, we can identify subtle structural features and stratigraphic variations that might be invisible in a standard seismic broadband image. Lower frequencies often highlight broader, thicker features, whereas higher frequencies enhance thinner stratigraphic detail and sharper boundaries. Key observations An RGB blending workflow was used to combine three selected frequencies into a single composite image. The chosen combination (reported in the manuscript as the best-performing set after testing) produces an RGB volume that highlights zones with multi-frequency coherence, interpreted as laterally continuous sand bodies or thickened reservoir packages (Fig. 9a,b). The derived geomorphological maps (Fig. 9c,d) show the Mamuniyat reservoir expressed as a distinctive white color, indicating the coincidence of all frequency components and implying robust seismic response across the bandwidth. Importantly, the wells fall predominantly within the white anomaly zone, and a similar white response is present in the western–central area where RMS and energy anomalies also occur (Fig. 9d). This convergence suggests that the anomaly is likely to represent a reservoir fairway rather than an isolated amplitude artifact. Fig. 9Results of spectral decomposition and RGB frequency blending applied to the Mamuniyat Formation: (a, b) selected frequency slices representing low-, mid-, and high-frequency components of the seismic data; (c) RGB-blended geomorphological map highlighting the lateral continuity and distribution of Mamuniyat reservoir sands; (d) RGB frequency map overlaid with well locations, illustrating the correspondence between multi-frequency seismic anomalies and sand-prone, prospective reservoir zones. They were generated using OpendTect 7 software (https://www.dgbes.com/software/opendtect). Results of spectral decomposition and RGB frequency blending applied to the Mamuniyat Formation: (a, b) selected frequency slices representing low-, mid-, and high-frequency components of the seismic data; (c) RGB-blended geomorphological map highlighting the lateral continuity and distribution of Mamuniyat reservoir sands; (d) RGB frequency map overlaid with well locations, illustrating the correspondence between multi-frequency seismic anomalies and sand-prone, prospective reservoir zones. They were generated using OpendTect 7 software (https://www.dgbes.com/software/opendtect). Spectral decomposition therefore provides an independent line of evidence that the Mamuniyat reservoir distribution is channelized and laterally variable, with a prominent fairway extending into the western–central area that may represent an untested or underdeveloped reservoir compartment. Similar successful applications of spectral decomposition in imaging channels and reservoir fairways have been widely documented16,40, reinforcing confidence in the interpretation. Petrophysical evaluation: reservoir quality, net pay definition, and lithology discrimination Petrophysical interpretation was performed to quantify shale volume, porosity, water saturation, net thickness, and net pay distribution within the Mamuniyat Formation. The results indicate that, although the reservoir is predominantly sand-prone, it exhibits significant intercalation of sandstone with shale. This heterogeneity is reflected in the variability of petrophysical properties, particularly porosity, which is influenced by the presence of shale laminations and dispersed clay content. While the reservoir quality is generally favorable, it shows notable spatial variability due to variations in shale volume and sedimentary architecture. Interbedded shale intervals contribute to porosity reduction through increased clay content, pore throat obstruction, and diagenetic effects. Given the significant shale content, shaly-sand models such as Indonesian were applied to obtain a more accurate estimation of water saturation. This heterogeneity is consistent with the depositional interpretation of stacked, channelized sand bodies and incised valley-fill systems, and is further supported by variations observed in amplitude and spectral attributes (Figs. 10, 11 and 12). Fig. 10Petrophysical cross-plot analyses for the Mamuniyat Formation: (a) cross-plot between core porosity and horizontal permeability showing a strong empirical correlation used to estimate porosity in uncored intervals; (b) Pickett plot of deep resistivity (LLD) versus effective porosity (PHIE) used to determine Archie parameters (a, m, n) and evaluate water saturation within the reservoir. It was generated using Interactive Petrophysics (IP) 4.7 software (https://www.geoactive.com/interactive-petrophysics). Petrophysical cross-plot analyses for the Mamuniyat Formation: (a) cross-plot between core porosity and horizontal permeability showing a strong empirical correlation used to estimate porosity in uncored intervals; (b) Pickett plot of deep resistivity (LLD) versus effective porosity (PHIE) used to determine Archie parameters (a, m, n) and evaluate water saturation within the reservoir. It was generated using Interactive Petrophysics (IP) 4.7 software (https://www.geoactive.com/interactive-petrophysics). The estimated shale volume (Vsh) shows relatively low values overall, ranging approximately from 5 to 25%, suggesting a generally clean reservoir interval with limited clay content (Fig. 11a). Total porosity values are reported to range from ~ 22% to 27%, while effective porosity is broadly within the ~ 10 to 12% range in interpreted productive intervals. Despite minor inconsistencies in the draft values, the combined interpretation of logs and cross-plots supports the conclusion that the Mamuniyat Formation contains porous, quartz-rich sandstone capable of significant hydrocarbon storage. Fig. 11Petrophysical parameter relationships and lithological discrimination for the Mamuniyat Formation: (a) effective porosity versus shale volume illustrating reservoir quality trends; (b) water saturation plots distinguishing reservoir and non-reservoir intervals; (c) Photoelectric Factor (PEF) vs. Bulk Density (RHOB) cross-plot for lithology identification; (d) M–N cross-plot showing the dominant lithotypes and mineralogical composition of the Mamuniyat reservoir; (e) Statistical distribution of grain density from core analysis in the Mamuniyat Formation, showing frequency and cumulative percentage. The dominant peak at 2.65 g/cc confirms sandstone lithology. It was generated using Interactive Petrophysics (IP) 4.7 software (https://www.geoactive.com/interactive-petrophysics). Petrophysical parameter relationships and lithological discrimination for the Mamuniyat Formation: (a) effective porosity versus shale volume illustrating reservoir quality trends; (b) water saturation plots distinguishing reservoir and non-reservoir intervals; (c) Photoelectric Factor (PEF) vs. Bulk Density (RHOB) cross-plot for lithology identification; (d) M–N cross-plot showing the dominant lithotypes and mineralogical composition of the Mamuniyat reservoir; (e) Statistical distribution of grain density from core analysis in the Mamuniyat Formation, showing frequency and cumulative percentage. The dominant peak at 2.65 g/cc confirms sandstone lithology. It was generated using Interactive Petrophysics (IP) 4.7 software (https://www.geoactive.com/interactive-petrophysics). A cross-plot calibration between core porosity and core permeability yielded a strong empirical relationship (R² > 0.85) (Fig. 10a), enabling estimation of porosity in uncored sections. This step is important for reducing uncertainty in vertical reservoir characterization and for ensuring consistent property trends across wells used later in 3D modeling61,62. Water saturation was estimated using Indonesian equation for shaley sand model, with formation constants determined using a Pickett plot approach. The reported Pickett plot interpretation indicates resistivity of formation water ~ 31%, a = 0.62, m = 1.95, and n = 1.75 (Fig. 10b). These calibrated parameters improve the reliability of saturation estimates compared to using generalized constants and support a reservoir interpretation where Sw varies from low to moderately high values, consistent with hydrocarbon-bearing intervals. By integrating Vsh, effective porosity, and water saturation, productive intervals were defined using cutoffs reported in the manuscript: PHIE > ~ 12%, Sw < ~ 50%, and Vsh < ~ 37% (Fig. 11a,b). These cutoffs distinguish reservoir from non-reservoir intervals and enable consistent net pay evaluation across the well set. The net pay thickness is reported as ~ 88.75 ft (Fig. 12), supporting the presence of a substantial productive package within the Mamuniyat Formation. Correlation panels across the field show that reservoir thickness and quality vary laterally, consistent with channelized depositional architecture and structural segmentation (Fig. 12). Fig. 12Stratigraphic correlation panel of the Mamuniyat Formation across selected wells in the I/R oil field, illustrating lateral variations in reservoir thickness, facies distribution, and continuity of the main reservoir intervals. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Stratigraphic correlation panel of the Mamuniyat Formation across selected wells in the I/R oil field, illustrating lateral variations in reservoir thickness, facies distribution, and continuity of the main reservoir intervals. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). The PEF vs. bulk density crossplot and the M–N crossplot indicate that quartz is the dominant mineral phase, with minor shale contributions (Fig. 11c,d). This interpretation is further supported by core grain density data, which show a dominant value of 2.65 g/cc, confirming sandstone lithology (Fig. 11e). This quartz-rich signature supports the interpretation of a high-quality clastic reservoir and helps explain the strong seismic response observed in amplitude attributes, since clean sands often produce a distinct acoustic impedance contrast relative to shale-prone units. Facies and 3D property modeling A 3D static model was built to integrate well-derived petrophysical properties with seismic interpretation and to provide a spatially continuous representation of facies architecture, reservoir quality distribution, and connectivity within the Mamuniyat Formation. Modeling was conducted following standard workflows for structural framework building, facies modeling, petrophysical upscaling, and property population45,63–70. Three main facies associations were modeled: sandstone (reservoir), shaly sandstone (poor reservoir), and shale (non-reservoir). The upscaling procedure (Figs. 13a,b and 14) demonstrates that well-scale facies and property variability were transferred to the model grid in a manner that preserves vertical trends while enabling field-scale mapping. The upscaled facies logs show good agreement with porosity and saturation behavior (Fig. 14), confirming that facies are the principal control on porosity distribution and that shale-rich intervals correspond to less effective porosity and higher water saturation. Fig. 13Facies upscaling and calibration for the Mamuniyat Formation: (a) comparison between original well-scale facies logs and upscaled facies within the reservoir model; (b) cross-plot illustrating the distribution and separation of the modeled facies classes used in the 3D static reservoir model. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Facies upscaling and calibration for the Mamuniyat Formation: (a) comparison between original well-scale facies logs and upscaled facies within the reservoir model; (b) cross-plot illustrating the distribution and separation of the modeled facies classes used in the 3D static reservoir model. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Fig. 14Vertical distribution of petrophysical properties and facies for the Mamuniyat Formation, showing upscaled lithofacies, effective porosity, and water saturation profiles used as input for 3D reservoir modeling. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Vertical distribution of petrophysical properties and facies for the Mamuniyat Formation, showing upscaled lithofacies, effective porosity, and water saturation profiles used as input for 3D reservoir modeling. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). The modeled facies distribution for the Mamuniyat interval indicates that sandstone facies are concentrated mainly in the central, northwestern, and southwestern parts of the study area (Fig. 15a). Shaly sandstone occurs as transitional belts, while shale facies occupy non-reservoir zones and likely correspond to lower-amplitude seismic regions. This distribution pattern is consistent with the channelized nature of the Mamuniyat reservoir inferred from stratigraphic concepts and spectral decomposition imaging (Fig. 9c,d). The presence of sandstone fairways in structurally favorable locations supports the interpretation that reservoir development is jointly controlled by depositional pathways and structural accommodation. Fig. 15Three-dimensional property model results for the Mamuniyat Formation in the I/R oil field: (a) facies distribution showing reservoir, poor reservoir, and non-reservoir facies; (b) effective porosity model illustrating spatial variation in reservoir quality; (c) water saturation model highlighting hydrocarbon-prone zones characterized by lower water saturation. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Three-dimensional property model results for the Mamuniyat Formation in the I/R oil field: (a) facies distribution showing reservoir, poor reservoir, and non-reservoir facies; (b) effective porosity model illustrating spatial variation in reservoir quality; (c) water saturation model highlighting hydrocarbon-prone zones characterized by lower water saturation. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). The effective porosity model (Fig. 15b) shows field-scale variability with enhanced porosity in the middle sector and gradual increases toward the northwest and southwest. The manuscript reports porosity ranges broadly from ~ 12% upward with local high values; while the draft contains some inconsistent numeric ranges, the spatial trend clearly indicates that the best porosity development coincides with sandstone fairways and prospective attribute anomalies. This consistency between facies and porosity provides confidence in the model representation. The water saturation model (Fig. 15c) indicates lower Sw values coincident with sandstone facies and with the amplitude anomaly trends, supporting a hydrocarbon-charged interpretation in parts of the reservoir. The model suggests decreasing Sw in the northeastern sector and the presence of favorable reservoir intervals in the central and northwestern parts of the field. These modeled trends align with the integrated attribute interpretation and provide a quantitative basis for prospect screening. Integrated prospect evaluation The integration of seismic attributes (variance, RMS, energy, spectral decomposition) with petrophysical evaluation and 3D property modeling enables identification of two prospective zones interpreted as new exploration targets in the I/R fields. The prospective areas are located within fault-related traps on the upthrown side of the main fault and are characterized by (i) high RMS amplitude, (ii) high energy attribute values, (iii) spectral decomposition white anomalies indicating multi-frequency coherence, (iv) sandstone-dominated facies, (v) elevated effective porosity, and (vi) lower water saturation (Table 1; Figs. 6, 9d, 15 and 16a–d). Cross-sections through the 3D models confirm that these zones are dominated by sandstone and shaly sandstone facies, with effective porosity generally in the ~ 18–30% range and reach to 90% in the middle part of the study area because it’s mainly consisted of sandstone only, a and water saturation approximately ~ 20–55%, consistent with favorable reservoir conditions described in the manuscript (Fig. 16b,c). Table 1Quantitative comparison between seismic attributes and well-derived reservoir properties (Mamuniyat Formation), in the I/R Oil Fields, Murzuq Basin, Libya.WellRMS amplitude (avg)Energy attribute (avg)Net pay (m)Effective porosity (%)Water saturation (%)I30.720.762114.830I40.690.731914.234I100.640.681613.538I110.660.701713.936I140.710.752014.632R10.750.792315.227R60.580.621412.942R70.600.641513.140R80.630.671613.637R100.670.711814.035R110.740.782215.029 Table 1Quantitative comparison between seismic attributes and well-derived reservoir properties (Mamuniyat Formation), in the I/R Oil Fields, Murzuq Basin, Libya.WellRMS amplitude (avg)Energy attribute (avg)Net pay (m)Effective porosity (%)Water saturation (%)I30.720.762114.830I40.690.731914.234I100.640.681613.538I110.660.701713.936I140.710.752014.632R10.750.792315.227R60.580.621412.942R70.600.641513.140R80.630.671613.637R100.670.711814.035R110.740.782215.029 Quantitative comparison between seismic attributes and well-derived reservoir properties (Mamuniyat Formation), in the I/R Oil Fields, Murzuq Basin, Libya. Fig. 16Integrated north–south and west–east cross-sections through the Mamuniyat Formation showing the relationship between facies, petrophysical properties, and seismic response: (a) lithofacies distribution highlighting sandstone, shaly sandstone, and shale; (b) effective porosity sections illustrating lateral and vertical variations in reservoir quality; (c) water saturation sections showing hydrocarbon-prone intervals characterized by lower water saturation; (d) RMS amplitude map with locations of the N–S and W–E profiles and the main structural elements. Dashed outlines mark the identified prospective zones (A & B) along the interpreted reservoir fairways. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Integrated north–south and west–east cross-sections through the Mamuniyat Formation showing the relationship between facies, petrophysical properties, and seismic response: (a) lithofacies distribution highlighting sandstone, shaly sandstone, and shale; (b) effective porosity sections illustrating lateral and vertical variations in reservoir quality; (c) water saturation sections showing hydrocarbon-prone intervals characterized by lower water saturation; (d) RMS amplitude map with locations of the N–S and W–E profiles and the main structural elements. Dashed outlines mark the identified prospective zones (A & B) along the interpreted reservoir fairways. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Critically, the prospective zones are not defined by a single dataset. Instead, they are supported by multiple independent indicators: structural positioning (fault-bounded trap geometry), seismic amplitude behavior (RMS and energy), frequency response (spectral decomposition). Based on the seismic attribute maps provided in this study these maps are highlighted shows several positive indicators that suggest it is a strong prospect. Surface Attribute & Structural Contours (Fig. 6a), This map displays the Structural Time Contours overlaid with a surface attribute, The blue-outlined area corresponds to a structural high (indicated by the contour values around − 960). The prospect is located in a favorable structural position. The white lines in the eastern part of the study area indicate faults, which seem to provide lateral sealing for the trap. The combination of high attribute values (warm colors) and structural closure suggests a “structural-stratigraphic” trap, where the reservoir quality is best at the crest of the structure.Seismic Energy Distribution (Fig. 6d), the highlighted area (dashed red circle) exhibits a high-energy “bright spot” High energy in this context often indicates a change in lithology or fluid content. In sandstone reservoirs, high amplitudes can be a “DHI” (Direct Hydrocarbon Indicator), suggesting the presence of gas or light oil which creates a high contrast in acoustic impedance compared to the surrounding rocks.Spectral Decomposition / RGB Blending (Fig. 8d), appears to be frequency-based attribute map. The area inside the dashed white circle shows a distinct “tuning” effect or a change in frequency response (indicated by the dark/black patches against the red background). Spectral decomposition is excellent for identifying bed thickness and stratigraphic edges. The anomaly here suggests a localized “sweet spot” where the reservoir thickness is optimal (tuning thickness) or where there is a significant change in the rock-fluid properties. It identifies the “geometry” of the sand body, which appears very well-defined in this prospect area. Surface Attribute & Structural Contours (Fig. 6a), This map displays the Structural Time Contours overlaid with a surface attribute, The blue-outlined area corresponds to a structural high (indicated by the contour values around − 960). The prospect is located in a favorable structural position. The white lines in the eastern part of the study area indicate faults, which seem to provide lateral sealing for the trap. The combination of high attribute values (warm colors) and structural closure suggests a “structural-stratigraphic” trap, where the reservoir quality is best at the crest of the structure. Surface Attribute & Structural Contours (Fig. 6a), This map displays the Structural Time Contours overlaid with a surface attribute, The blue-outlined area corresponds to a structural high (indicated by the contour values around − 960). The prospect is located in a favorable structural position. The white lines in the eastern part of the study area indicate faults, which seem to provide lateral sealing for the trap. The combination of high attribute values (warm colors) and structural closure suggests a “structural-stratigraphic” trap, where the reservoir quality is best at the crest of the structure. Seismic Energy Distribution (Fig. 6d), the highlighted area (dashed red circle) exhibits a high-energy “bright spot” High energy in this context often indicates a change in lithology or fluid content. In sandstone reservoirs, high amplitudes can be a “DHI” (Direct Hydrocarbon Indicator), suggesting the presence of gas or light oil which creates a high contrast in acoustic impedance compared to the surrounding rocks. Seismic Energy Distribution (Fig. 6d), the highlighted area (dashed red circle) exhibits a high-energy “bright spot” High energy in this context often indicates a change in lithology or fluid content. In sandstone reservoirs, high amplitudes can be a “DHI” (Direct Hydrocarbon Indicator), suggesting the presence of gas or light oil which creates a high contrast in acoustic impedance compared to the surrounding rocks. Spectral Decomposition / RGB Blending (Fig. 8d), appears to be frequency-based attribute map. The area inside the dashed white circle shows a distinct “tuning” effect or a change in frequency response (indicated by the dark/black patches against the red background). Spectral decomposition is excellent for identifying bed thickness and stratigraphic edges. The anomaly here suggests a localized “sweet spot” where the reservoir thickness is optimal (tuning thickness) or where there is a significant change in the rock-fluid properties. It identifies the “geometry” of the sand body, which appears very well-defined in this prospect area. Spectral Decomposition / RGB Blending (Fig. 8d), appears to be frequency-based attribute map. The area inside the dashed white circle shows a distinct “tuning” effect or a change in frequency response (indicated by the dark/black patches against the red background). Spectral decomposition is excellent for identifying bed thickness and stratigraphic edges. The anomaly here suggests a localized “sweet spot” where the reservoir thickness is optimal (tuning thickness) or where there is a significant change in the rock-fluid properties. It identifies the “geometry” of the sand body, which appears very well-defined in this prospect area. We concluded the zone within the dotted line represents a high-priority drilling target because it combines a structural trap with positive seismic indicators (DHI) for hydrocarbons. Finally, petrophysical property trends (porosity and Sw). This multi-evidence approach reduces interpretation non-uniqueness and strengthens the case that these anomalies reflect genuine reservoir fairways with hydrocarbon potential rather than lithologic noise or processing artifacts. Implications for reservoir development and uncertainty reduction The results demonstrate that the Mamuniyat Formation in the I/R oil fields is a heterogeneous, sand-prone reservoir where quality distribution is controlled by the interplay of glacially influenced depositional architecture and fault-related structural segmentation. Variance attributes provide a robust structural framework for understanding compartmentalization (Fig. 5), while RMS amplitude, energy, and spectral decomposition collectively define reservoir fairways and highlight prospective zones (Figs. 6, 7, 8 and 9). Petrophysical analysis confirms low shale volumes, favorable porosity, and variable water saturation that can be used to define net pay consistently (Figs. 10, 11 and 12). Finally, 3D modeling integrates these inputs and provides a spatially continuous view of facies and reservoir properties, enabling identification of new prospect zones and supporting drilling and development planning (Figs. 13, 14, 15 and 16). Overall, the agreement between seismic-derived indicators and well-based petrophysical properties suggests that the workflow applied in this study is effective for reducing uncertainty in reservoir distribution and for identifying additional opportunities in mature Paleozoic reservoirs of the Murzuq Basin. The approach is also transferable to analogous glaciogenic clastic reservoirs elsewhere in North Africa, were channelized sand bodies and stratigraphic complexity often complicate prediction of reservoir continuity and quality. A blind well validation was conducted to assess the reliability of the 3D reservoir model. One well (W5) was excluded from the geostatistical modeling process and used as an independent test (Fig. 17). The model-predicted properties, including facies and porosity, were then compared with the actual well-log data at the blind well location. The results show a good agreement between predicted and observed values, indicating that the model successfully captures the spatial distribution of reservoir properties and has strong predictive capability. Fig. 17Three-dimensional reservoir models of the Mamuniyat Formation in the I/R oil field showing (a) porosity distribution (low–high) and (b) facies distribution (reservoir, shaly sand, and shale), integrated with well data and structural framework. Well W5 is highlighted as a blind test well and excluded from the modeling process. (c) Comparison between model-predicted and actual porosity from well logs at Well W5, demonstrating good agreement and validating the reliability of the reservoir model. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Three-dimensional reservoir models of the Mamuniyat Formation in the I/R oil field showing (a) porosity distribution (low–high) and (b) facies distribution (reservoir, shaly sand, and shale), integrated with well data and structural framework. Well W5 is highlighted as a blind test well and excluded from the modeling process. (c) Comparison between model-predicted and actual porosity from well logs at Well W5, demonstrating good agreement and validating the reliability of the reservoir model. It was generated using Petrel 2025 software (https://www.slb.com/products-and-services/delivering-digital-at-scale/software/petrel-subsurface-software). Conclusions This study demonstrates that an integrated workflow combining well-log petrophysical evaluation, 3D seismic interpretation, seismic attribute analysis, spectral decomposition, and 3D static reservoir modeling provides a robust and reliable approach for characterizing the Upper Ordovician Mamuniyat Formation in the I/R oil fields, Murzuq Basin, Libya. Seismic interpretation and variance attribute analysis reveal a structurally complex reservoir system dominated by a major NW–SE-trending fault system with associated subsidiary faults that control reservoir compartmentalization, continuity, and lateral connectivity. Amplitude-based attributes, including RMS amplitude and energy, effectively delineate sand-prone fairways and prospective zones, while spectral decomposition enhances the visualization of depositional architectures and geomorphological features, supporting the identification of laterally continuous reservoir bodies and potential hydrocarbon-related seismic anomalies. Petrophysical analysis indicates that the Mamuniyat Formation is primarily composed of clean, quartz-rich sandstones with low shale content, moderate to good effective porosity, and variable but locally reduced water saturation. The integration of shale volume, porosity, and water saturation logs enables consistent delineation of net reservoir and net pay intervals, confirming the high storage capacity and hydrocarbon potential of the formation. Cross-plot analysis further substantiates the dominance of sandstone and shaly sandstone facies as the main controls on reservoir quality heterogeneity. The constructed 3D facies and property models reveal significant spatial variability, with high-quality reservoir zones predominantly distributed in the central, northwestern, and southwestern parts of the study area, where enhanced porosity commonly coincides with lower water saturation. Moreover, the integration of seismic attributes with petrophysical and modeling results has led to the identification of two new prospective zones located on the upthrown side of the main fault, characterized by favorable seismic responses, sandstone-dominated facies, improved reservoir properties, and reduced water saturation, indicating strong hydrocarbon potential. The reliability of the modeling approach is further supported by blind well validation, demonstrating good agreement between predicted and observed petrophysical properties. Overall, this integrated methodology significantly reduces geological uncertainty, improves reservoir predictability, and provides a transferable framework for optimizing exploration, appraisal, and development strategies in structurally complex clastic reservoirs. At this stage, the identified zones are considered preliminary targets, and no volumetric estimates (e.g., STOIIP/GIIP) or probabilistic assessments have been performed. Detailed volumetric calculations and uncertainty analysis are recommended in future studies to better quantify the hydrocarbon potential of these zones.