Variable density and chemical reaction effects on heat and mass transfer of magnetic second-grade nanofluid flow under slip conditions Authors: Mhamed Benaissa, Zia Ullah, Feyisa Edosa Merga, Asmaa Farouk, Mohamed S Hamdy, Noureddine Elboughdiri, Djamel Ghernaout, Alsamani A M Salih, Nidhal Ben Khedher Published: 2026 ABSTRACT AbstractSlip flow, exponential thermal-density and second-grade nanofluid over horizontal stretching circular cylinder has many applications in heat exchangers, pipelines, rocket bodies, aircraft fuselages, submarine hulls, offshore structures, and flow bodies of industrial sectors. This research presents the thermal dependent density and chemical reaction effect on MHD second-grade nanofluid motion of heat and mass transmission over horizontal stretching circular cylinder with thermal-concentration slip. The importance of applied magnetic field is used for maximum increment of heat transport. The coupled partial differential equations of second-grade nanofluid are transformed into ordinary differential equations with help of well-defined similarity variable and stream functions. The average and central difference formula of finite-difference method with Newton–Raphson scheme are employed to find numerical outcomes of nonlinear ordinary differential equations through MATLAB software. Several physical parameters such as magnetic field (), second grade parameter (K1), chemical reaction parameter (Cr), density number (n), thermal slip (BT), and concentration slip (BC) are used for temperature, concentration, and velocity variations. The skin friction rate, local Nusselt number, and Sherwood number are numerical and graphically presented using different physical parameters. It is noted that the velocity profile decreases with increasing magnetic parameter because stronger magnetic field opposes the fluid motion and acts like a braking mechanism. The stronger slip performance in fluid temperature and fluid concentration is observed at each value of thermal slip and concentration slip parameter. The skin friction rate is higher with increasing Prandtl number but Nusselt number decreases with increasing Brownian motion. The magnitude of isothermal contours enhances as chemical reaction and magnetic field enhance under slip conditions.Keywords: MHD second-grade nanofluid, Thermal-concentration slip, Exponential variable density, Chemical reaction, Heat and mass transport, Chemically-reactive cylinder Introduction The second-grade nanofluid is the combined form of complex strain–stress properties of second-grade liquids with enhancing characteristics of thermal conductivity which refers the prominent application of heat and mass transfer in engineering and nanotechnology. With normal stress difference and non-Newtonian liquids, the second-grade nanofluid is more suitable for lubricants, polymers, biological liquids, and crude oil in the presence of shear thickening and shear thinning properties. Choi [1] introduced nanofluid with suspended nanoparticles that plays a significant role in the field of engineering and technology. Applications of nanofluids include cooling nuclear reactors and automobiles, accelerating heat transfer in computer micro-chips, the preparation of food, fuel cells, and modes of transport. Nanofluids improve the thermal conductivity and heat transfer rate of conventional base liquids (water, glycol, ethylene, and oil) when a small number of nanoparticles (usually composed of Ag, Au, Al, or their oxides) with sizes ranging from 1 to 100 nm are added. A substantial number of investigations were performed relative to nanofluids. Shehzad et al. [2] examined the three-dimensional Jeffrey nanofluid motion with radiating energy within heat production. Kakac and Yener [3] investigated the convective heat transfer through conduction, convection and radiation. Khan et al. [4] explored the three-dimensional flow of a spinning nanofluid through convection mechanism over a stretching surface. They examined nanofluid flows under the effect of heat transmission using two different models. Authors [5] used the Duan-Rach methodology of generalized Adomic Decomposition method to study MHD radiating nanofluid movement between stretching and shrinking surface. Ramzan and Bilal [6] introduced a chemical reaction-based solution for MHD multidimensional viscoelastic nanofluid flow for thermal enhancement and flow characteristics. To determine an appropriate series solution, they employed HAM technique for numerical results of heat transfer. By applying the Buongiorno model, the MHD double-diffusive nanofluid motion under the impact of natural circulation was evaluated by Akbar et al. [7] over the stretched surface. Salem et al. [8] explored the heat transfer and temperature distribution of magnetic non-Newtonian fluid with mixed convection and variable density effects. Noor et al. [9] investigated the slip performance of temperature distribution over vertically expanding surface using micro-polar nanofluid flow. Siddiqa et al. [10, 11] used the influence of thermal radiation and variable density effects in natural and mixed convection flow over circular and vertical surface numerically. The influence of magneto-hydrodynamic, Soret/Dufour, Newtonian heating, and viscous dissipation on nanofluid flow for heat and mass transfer was examined [12, 13]. Further recent studies of nanofluid flow and heat transfer in this area are included in [14]. Saini and Agrawal [15] studied the influence of radiation, heat generation and slip conditions on nanofluid flow for temperature and concentration performance over shrinking sheet. The investigation of non-Newtonian fluids has garnered significant attention from scientists and researchers in recent years due to its diverse geophysical and technological uses, including oils, blood at extremely low shear rates, paints, shampoos, polymer compounds, colloidal form liquids, cosmetic products, pasta, suspending liquids, ice cream, and dough flour. The natural and synthetic nanofluid can be utilized in biotechnology, food manufacturing, drilling procedures, and red blood cells, particles, and extending chain polymers. These fluids have a nonlinear relationship between variable viscosity and shear rate, and the resultant products have a variety of rheological properties. The whole properties of non-Newtonian liquids cannot be uncovered by an individual governing model. For technical and industrial-focused manufacturing processes like hot rolling, papermaking, fiber optics, and metal extrusion, the flow of extensible boundary layer motion is becoming more and more significant. The works of [16, 17] inspired other scholars to submit more creative concepts. Mustafa et al. [18] addressed the three-dimensional rotational motion of ferro-fluid caused by a radiated layer under the effect of magneto-hydrodynamics. A novel concept of radiating heat flow in nonlinear form was examined in relation to a mixture of nanoparticles. The impacts of Soret/Dufour on MHD second-grade viscous fluid flow across a porous oscillatory stretching sheet for heat radiation were discussed in reference [19]. The effects of ohmic dissipation and thermal radiation on MHD nanofluid flow over nonlinear porous stretching sheet were explored in references [20, 21]. The performance of heat and mass transfer of second-grade nanofluid flow over permeable stretching surface was examined by Abbas et al. [22]. Several authors [23, 24] examined the slip boundary effects on temperature and concentration profiles of second grade and ternary hybrid nanofluid flow numerically. The exothermic catalytic chemical reaction effect on magnetic-driven nanofluid flow for heat transfer and temperature performance was computed in references [25, 26]. The steady free convective flow of nanofluid and magnetic boundary layers of radiative nanofluid were computed in references [27, 28]. The radiating heat transfer and natural convection flow of fluid over wavy cylindrical wall were calculated in references [29, 30]. Agrawal and Saini [31] performed mathematical analysis for thermal transport and slip performance of temperature distribution over stretching surface in the presence of thermal radiation. Saini et al. [32] used the effects of viscous dissipation and chemical reaction on unsteady nanofluid flow for heat and mass transfer performance within the magnetic field. The novelty of current analysis presents the influence of temperature dependent density, chemical reaction, and magnetic field on heat and mass transfer performance of second-grade nanofluid. The flow of nanofluid is performed over tow-dimensional horizontal cylinder with thermophoresis and Brownian motion effects. In above literature, studies are performed at small temperature difference between the surface and ambient fluid. In thermal engineering, the circumstances may arise where temperature difference is large. In this situation, the density of fluid is assumed as exponential function of temperature which clearly describes research gap between present and existing studies. By following [8, 10, 11], the nanofluid model is solved using appropriate similarity variables and stream functions in the presence of thermal and concentration slip effects. The main objective of this study signifies the slip performance in temperature and concentration profiles at large temperature difference. The numerical outcomes of physical properties are calculated through using Newton Raphson technique with central difference formula of finite difference method. The steady performance of skin friction, Nusselt number and Sherwood number is computed in MATLAB tool. The important research questions about current analysis are discussed below. How thermal and concentration slip parameters improve the performance of temperature and concentration profiles along horizontal circular cylinder? How thermal and concentration slip parameters improve the performance of temperature and concentration profiles along horizontal circular cylinder? How temperature dependent density signifies the surface temperature and Nusselt number? How temperature dependent density signifies the surface temperature and Nusselt number? How chemical reaction and magnetic field control the flow characteristics and mass transfer? How chemical reaction and magnetic field control the flow characteristics and mass transfer? Which parameter indicates significant improvement in skin friction and Nusselt number? Which parameter indicates significant improvement in skin friction and Nusselt number? How thermophoresis and Brownian motion improve the fluid velocity and concentration? How thermophoresis and Brownian motion improve the fluid velocity and concentration? Flow geometry and second grade nanofluid model The impact of chemical reactions and nanofluid thickness on MHD second-grade nanofluid heat and mass transport over horizontal stretching circular cylinder with thermal and concentration slip is the primary goal of this study. The well-defined streaming functions and similarity factors are used to convert the pair of partial differential equation models of second-grade nanofluid into ordinary differential equations. MATLAB software is used to determine the visual and computational outcomes of resulted linearized ordinary differential equations using Newton Raphson procedure and central difference approach. The importance of second grade nanofluid movement over horizontal stretching circular cylinder using temperature slip and concentration slip effects is displayed in Fig. 1. The velocity components and directional components are presented by and along the cylinder. The symbol for temperature is denoted with T. Here represents heat conductivity of second grade nanofluid, is specified for heat capacity, is specified for ambient temperature of sheet, ρ is the fluid density, particle density of the fluid is indicated by , and is the kinematic liquid viscosity with acceleration due to gravity g. The current physical model is governed through Cauchy stress tensor; where, denotes the incompressibility conditions, represents viscous effects, the vector form of second grade fluid velocity is signified by V, and ∇ shows the gradient operator. The terms and indicate the modulus of normal stress, whereas and characterize the kinematic tensors. The differential term represents the differential value of materials and the terms μ, α1 and α2 satisfied the following relation of Eq. (4): Second grade nanofluid movement over horizontal stretching circular cylinder In above literature, the studies are investigated with small temperature difference between the surface and ambient temperature. In thermal engineering systems, the conditions develop where high temperature difference is observed. In this condition, the Boussinesq approximation becomes unsuitable. Therefore, the temperature dependent density is assumed to control the high temperature difference between the surface and fluid by following [3]. The temperature dependent density function is proposed below: where, It is noted that the volumetric expansion coefficient () is generally very small for most fluids, usually on the order of 10–3. The Boussinesq approximation can be derived through Eq. (1) by using Taylor series expansion and neglecting the higher order terms. Boussinesq approximation signifies an important role for small temperature difference otherwise Eq. (1) is not suitable for high temperature difference. In literature, it was observed that the variable density avoids erroneous solutions in high temperature circumstances. The mathematical equations for current nanofluid model are provided below by following [5, 9, 11, 12]. Equation (7) presents the momentum equation for steady incompressible second-grade nanofluid flow with magnetic field and buoyancy effects. The left hand side of equation indicates the convective acceleration which represents transport of momentum due to motion of fluid itself. The right hand side presents viscous diffusion, non-Newtonian characteristics of second grade nanofluid, magnetic force and free convection effect caused by density differences within the fluid. Equation (10) presents the boundary condition of velocity, temperature and concentration at the surface and far away from the surface. The condition () signifies no penetration of fluid through solid surface and condition () highlights the stretching velocity which deives the fluid motion along the cylinder surface. The thermal slip condition () presents fluid temperature adjacent to the wall not exactly equal to the wall temperature. The parameter () controls the strength of thermal slip. Similarly, the solutal slip condition () indicates the concentration jump behavior at the surface. The linear slip conditions provide simplified and realistic approximation of nanoscale and microscale transport phenomena. The boundary conditions are defined below by following [9, 14, 23]: Stream functions and similarities In above nonlinear partial differential equations, the stream functions are designed to approximate the results of the above mentioned second grade nanofluid problem into ordinary form. These functions and variable are very essential to reduce the number of various parameters into important physical factors. Additionally, these functions generate ordinary form of second grade nanofluid model into single differential based equations. The similarity variables and stream functions are included with constant pressure in Eq. (11). The approximate component of stream functions and value of similarity variable is described in Eq. (12). Employing this similarity operator, the present model is reduced to an ordinary differential based model. These one-variable based models provide straightforward solutions for desired physical results. The main objective for applying the stream parameters and the previously described similarities signifies reduced form of ordinary relation for certain pertinent factors. These specific characteristics play a significant role in producing computational knowledge to support unknown functions under convective conditions. The reduced ordinary differential forms of differential equations are presented below. The reduced ordinary forms of boundary values are presented below. From above reduced ODEs (13)–(16), the following unit-free physical parameters such as buoyancy factor modified Grashof parameter Lewis parameter Prandtl parameter thermal-slip parameter concentration slip parameter Brownian motion factor thermophoresis factor chemical reaction factor Lorentz/magnetic force parameter and second-grade factor are generated for numerical solutions. The corporal characteristics for the significance of skin friction coefficients, Sherwood quantity, and Nusselt amount are presented in Eqs. (17)–(19). The values for these terms are given below by following references [20, 21]. Following outcomes can be obtained by applying the similarity function of Eqs. (11)–(12) into Eqs. (17)–(19): Numerical procedure and computational scheme Keller box method known as implicit finite-difference method is applied to solve the numerical outcomes of ordinary differnetial equations under defined boundary condictions. This method is applied with following steps and mentioned in the flow chart through Fig. 2. Keller box method develops smooth convergence and accuracy in the approximation of boundary layers with Newton Raphson scheme. Keller box method provides efficient and robust results of ODEs with complex boundary conditions and nonlinearities. This method is very powerful tool for engineers and scientists dealing with challenging ODEs. This is only single method with Newton Raphson scheme. Equations (13), (14), (15) and (16) are initially converted into first order ODEs by using difference equtions with average and central difference formulation as follows: Flow chart for the procedure of Keller box method on ordinary differential equations Consider the new variables as given in Eq. (23). These new variables converts the the higher order ODEs into first order ODEs. Using Eq. (23) in Eqs. (13), (14) and (15), the first order ordinary differential equations are gven below. Additionally, the Eq. (23) is arranged in simplified form as given below. The converted boundary conditions are derived below: Now the interval of the proposed model [0, ] will be divided into N subintervals with initial step size with , and where = 1, 2, 3,….N. Additionally, the horizontal midpoints , and are defined in net rectangle mesh points for difference approximation through Fig. 3. The finite differences for first order derivative w.r.t and midpoints and are applied in above equations by replacing . The final finite difference approximations are given below. Net rectangle for difference approximation using mesh structure Newton’s technique Keller box method converts the governing nonlinear ODEs into system of nonlinear algebraic equations after discretization. The solution of nonlinear equation is not possible directly using ordinary matric techniques. Therefore, the Newton Raphson method is employed to linearize the nonlinear algebraic equations at each iteration step. Several mesh sizes N = 1001, 201, 301, and 401 are performed for grid independence test to compute accuracy of results. It is noticed that the variations in physical quantities such as skin friction, Nusselt number and Sherwood number are negligible at N = 401. Therefore, the mesh N = 401 with and tolerance 10–15 are used for numerical outcomes. Moreover, Newton Raphson method provides rapid quadratic convergence, stability and accuracy in boundary layers. The nonlinear algebraic system is presented with R(X) = 0, where X is the solution vector. The convergence criteria used in computations is denoted with max by using Quasi linearization . Therefore, Keller box method handles discretization and Newton–Raphson method handles nonlinear iteration and solution convergence. The linear system of equations is given below. Block-elimination method After using Newton–Raphson method for linearization of nonlinear algebraic equations obtained from Keller box discretization, very large system of linear equations is generated. The block elimination method is used to solve these linear algebraic equations to compute several physical quantities such as velocity, temperature, concentration, skin friction, Nusselt number and Sherwood number at each grid point. The block tri-diagonal matric is generated instead of simple coefficient matrix. The block tri-diagonal matrix is given in Eqs. (51) and (52), where A is block tri-diagonal coefficient matrix, is vector of connections to unknown variables, and r is residual vector. Results and discussion This study presents exponential variable density and chemical reactions effects on the transfer of heat and mass in MHD second-grade nanofluid over horizontal stretching circular cylinder with thermal and concentration slips. The second-grade nanofluid illustrates the effect of physical variable such as magnetic field (Mf), second grade parameter (K1), chemical reaction parameter (Cr), density index (n), thermal-slip (BT), and concentration-slip (BC) on velocity, fluid-temperature and fluid-concentration profiles. The impact of Brownian motion parameter on Nusselt and Sherwood rate is expressed in graphical form. The skin friction coefficient, Nusselt and Sherwood number rate are determined in numerical form for different physical parameter. Figure 4a–d highlight the influence of magnetic force 1.8 and chemical reaction and 1.2 on velocity contours and temperature contours along stretching cylinder in two-dimensional region. The level of velocity contours increases at lower and decreases at higher due to resistive Lorentz force. The maximum level of velocity contours is observed in 9 ~ 10 region over expanding cylinder. For small choice of reaction parameter the maximum level of velocity contours is detected. The minimum level of velocity contours is found as reaction factor =1.2 enhances. In Fig. 5a–d, the effect of magnetic force 1.2 and chemical reaction and 1.0 on temperature contours along stretching cylinder in two-dimensional region is displayed. The high percentage of temperature contours is found as magnetic force increases and decreases at lower magnetic force Similarly, the high percentage of temperature contours is found as reaction factor increases and decreases at lower reaction factor In Fig. 6a–d, the iso-concentration contours of second-grade nanofluid flow are displayed of two values of reaction rate Cr = 0.3, 0.7 and concentration slip BC = 0.2 and 2.2. In Fig. 6a, the lower magnitude of iso-concentration contour is depicted at smaller Cr = 0.3. At larger Cr = 0.7, the rate of iso-concentration contour increases along the surface of cylinder in Fig. 6b. In Fig. 6c, the maximum magnitude of iso-concentration contour is found at lower concentration slip BC = 0.2. In Fig. 6d, the rate of iso-concentration contour increases as concentration-slip factor enhances. Figure 7a–c highlight the impact of Cr = 0.1, 0.3, 0.5, 0.7, 0.9 on quantities with constant values of other physical parameters. The graphical observation showed that the fluid velocity profile enhances as Cr parameter increases while maximum magnitude is observed at Cr = 0.9, as shown in Fig. 7a. It is noted that the boundary layer thickness increases as chemical reaction factor is increased. The enhanced thermal performance in temperature profiles is noted as each value of Cr. In Fig. 7b, the thermal slip reaches its minimal value at a higher value of Cr = 0.9 and reaches its maximum value preferably at Cr = 0.1 factor. The graphical findings revealed that the concentration slip performance enhances at lower value at Cr = 0.1 and lowest rate is recorded at Cr = 0.9, as shown in Fig. 7c. Physically in convective nanofluid flows, the concentration field contributes to the buoyancy force through the solutal buoyancy term. When the chemical reaction parameter increases, it modifies the concentration distribution near the surface, which can modify the fluid motion. Figure 8a, b, and c show how buoyancy parameter λ = 0.1, 0.2, 0.3, 0.4, 0.5 affect the physical quantities in the presence of several constant fixed parameters. The graphical observation showed that stronger amplitude in velocity profile is depicted at maximum = 0.5, as shown in Fig. 8a. The decreasing magnitude of fluid velocity is observed at lower buoyancy parameter = 0.1. The thermal slip behavior decreases at lower = 0.1 but enhances as is increased from 0.1 to 0.5 as shown in Fig. 8b. Similarly, the stronger slip performance is observed in concentration profile than temperature profile due to stronger solutal slip effects in Fig. 8c. Physically in mixed convection flows, temperature differences create density variations in the fluid. The heated fluid rises while the cold fluid sinks, producing a buoyancy force that drives the velocity field. a–d Velocity contours for magnetic force and reaction rate factors a–d Temperature contours for magnetic force and reaction rate factors a–d Iso-concentration contours for reaction rate and concentration-slip factors a–c Demonstrate the effect of Cr on a–c Demonstrate the effect of λ on Figure 9a, b, and c demonstrate the effect of Mf = 0.2, 0.4, 0.6, 0.8, 1.0 on quantities under some fixed constant parameters. The graphical study revealed that velocity profile improves at lower Mf = 0.2 but decreases as magnetic parameter increases in Fig. 9a because Lorentz force opposes the fluid motion and decreases the velocity field. The increasing amplitude is observed at lower value of magnetic parameter. The slip performance in temperature profile is improved at each value of Mf in Fig. 9b. The increasing magnitude is observed at lower Mf = 0.2. The higher temperature rate is observed at smaller Mf = factor and lowest value reached at a greater value of Mf = 1.0. According to the graphical outcomes, the concentration transmission rate is reached the highest possible level at Mf = 0.2 and lowest rate is observed at Mf = 1.0, as shown in Fig. 9c. When a magnetic field is applied to an electrically conducting fluid, the motion of the fluid under the magnetic field produces a resistive force called the Lorentz force. This force opposes the flow motion and converts kinetic energy into thermal energy within the fluid. Figure 10a, b, and c illustrate the effect of BC = 0.1, 0.5, 1.0, 1.5, 2.0 on physical quantities fixed value for the other physical parameters. As seen in Fig. 10a, the graphical inspection demonstrated that the velocity pattern is increased as BC increases and reached the highest possible level at BC = 2.0. It is mentioned that when the concentration slip parameter increases, the thickness of momentum boundary layer enhances. However, when the BC parameter increases, the thermal rate is reduced. As seen in Fig. 10b, the thermal output reaches its lowest point at a higher value of BC = 2.0 and reaches its highest value at smaller BC = 0.1. As seen in Fig. 10c, the graphical findings show the stronger concentration slip transmission at BC = 0.1 as compared to BC = 2.0. Physically, the solutal slip parameter reduces the mass transfer rate from the surface to the fluid, which weakens species diffusion near the boundary layer. As a result, the concentration profile decreases because fewer solute particles enter the fluid region. a–c Demonstrate the effect of Mf on a–c Demonstrate the effect of BC on Figure 11a, b, and c indicate the effect of BT = 0.2, 0.4, 0.6, 0.8, 1.0 on physical quantities of in the presence of several fixed constant parameters. Figure 11a illustrates the graphical conclusion of velocity pattern and increases as BT is increased but reached its maximum rate at BT = 1.0. It is noticed that stronger thermal slip signifies the higher magnitude of thermal boundary layer along stretching cylinder. At enhancing BT factor, the thermal rate is declined. As seen in Fig. 11b, the thermal rate reaches its minimum value at a higher value of BT = 1.0 but higher level is observed at BT = 0.2. Figure 11c illustrates the graphical findings, which showed that the slip concentration transmission rate reached its peak value at BT = 0.2 and its minimal rate at BT = 1.0. Physically, an increase in the thermal slip parameter weakens heat transfer from the heated surface to the fluid, leading to a reduction in the temperature profile and thinning of the thermal boundary layer. Due to the coupling between heat and mass transfer, the concentration profile also decreases slightly. Figure 12a, b, and c demonstrate the effect of density parameter n = 0.1, 0.2, 0.3, 0.4, 0.5 on physical outcomes of with fixed constant parameters. Figure 12a illustrates the graphical finding of stronger velocity profile as n is increased and reached its greatest rate at n = 0.5. It is observed that when the density parameter enhances, the thickness of the boundary layer grows. On the other hand, as the n factor is increased, the thermal rate is reduced. As observed in Fig. 12b, the thermal rate reaches its minimum value at upper rate of n = 0.5 and reaches its maximum rate at lowest n = 0.1. As seen in Fig. 12c, the graphical findings of higher slip concentration transmission are observed at n = 0.1 and a lowest rate is found at n = 0.5. An increase in the variable density parameter strengthens buoyancy effects, which enhances fluid motion and improves thermal energy transport, thereby increasing the velocity profile. Enhanced convection also promotes species diffusion, leading to an increase in the concentration profile. While holding the other fixed parameters, Fig. 11 shows how NT = 0.1, 0.2, 0.3, 0.4, and 0.5 affect the physical Nusselt and Sherwood quantities. According to the graphical study, the Sherwood rate and Nusselt number are dropped as the NT enhances. The maximum increment in Nusselt number is observed at lower NT. In Fig. 11, it is observed that the magnitude of Nusselt number and Sherwood number reaches its highest point at a lower value of NT = 0.1, decreases further as the NT factor increases. Physically, higher thermophoresis parameter drives nanoparticles away from the heated surface toward the ambient fluid, which thickens both the thermal and concentration boundary layers. Consequently, the temperature and concentration gradients at the wall decrease, resulting in lower Nusselt number and lower Sherwood number. a–c Demonstrate the effect of BT on a–c Demonstrate the outcome of n on Table 1 indicates the comparison of skin friction, Nusselt number and Sherwood number between present results and existing literature [23] numerically. It is noted that skin friction, Nusselt number and Sherwood values decrease as thermophoresis parameter is increased from 0.7 to 1.0 and showed significant agreement between present and published results. Table 2 signifies the comparison of Nusselt number with the published work [7]. The excellent agreement between the current and existing results is observed at each value of Prandtl number Pr. It is noticed that the increasing Nusselt number is observed as Pr increases from 7.0 to 70.0. Table 3 and Fig. 13 show the impact of Pr = 0.1, 0.3, 0.5, 0.7, 0.9 on skin friction, Nusselt number and Sherwood number in the presence of some fixed parameters. Table 3 and Fig. 14 revealed that the skin friction coefficient increases as Pr factor is increased, reaching its greatest rate at Pr = 0.9. It is found that the Nusselt and Sherwood numbers enhance as the Pr factor grows, reaching the maximum magnitude at Pr = 0.9 as compared to Pr = 0.1. The effects of Le = 0.1, 0.2, 0.3, 0.4, and 0.5 on skin friction, Nusselt number, and Sherwood number are explored in Table 4 with some constant physical parameters in Fig. 15. Table 4 revealed that the skin friction profile grows well as the Le factor increases, attaining its maximum magnitude at Le = 0.5. It also detected that the Nusselt number and Sherwood number enhance as Le factor is increased and achieved stronger magnitude at Le = 0.5 as compared to Le = 0.1. Table 5 and Fig. 16 display the impact of NB = 0.1, 0.2, 0.3, 0.4, 0.5 on skin friction, Nusselt number and Sherwood number quantities in the presence of fixed constant parameters. It is noticed that the skin friction coefficient enhances as the NB factor is enhanced from 0.1 to 0.5, reaching its maximum rate at NB = 0.5. Additionally, it is seen that the Nusselt number declines as the NB factor is enhanced, reaching upper level at lower NB = 0.1 as compared to NB = 0.5. However, the enhancing rate of Sherwood quantity is observed at higher value of Brownian motion parameter. Physically, a higher Brownian motion parameter enhances random nanoparticle movement, which intensifies particle interaction and fluid mixing near the wall. This strengthens the concentration gradient and momentum transport, leading to an increase in the Sherwood number and skin friction coefficient. Table 1Comparison of presents results () with existing results [23]Ramzan et al. [23]Present results0.73.597590.194430.056823.597560.194410.056780.93.568810.193230.018963.568770.193200.018941.03.554200.192580.001703.554180.192550.00166 Comparison of presents results () with existing results [23] Table 2Comparison of presents results () with existing results [7]Prandtl number PrAkbar et al. [7]Present resultsError analysis7.01.895401.895370.0000320.03.353903.353880.0000270.06.462206.462210.00001 Comparison of presents results () with existing results [7] Table 3Showed the impact of Pr = 0.1, 0.3, 0.5, 0.7, 0.9 on skin friction, Nusselt number and Sherwood numberPr0.10.7934513377055500.1282503088066880.3744404289539370.31.0608584015735990.2480305292969640.4049573821212550.52.4311586500136370.3104519597835750.4141069147967660.73.6258547920641470.3436590538026410.4199622106002650.94.7104731096247800.3653795968474100.424431219241599 Showed the impact of Pr = 0.1, 0.3, 0.5, 0.7, 0.9 on skin friction, Nusselt number and Sherwood number a, b Demonstrate the effect of NT on Nusselt and Sherwood number Numerical outputs of skin friction, Nusselt number and Sherwood number for different Pr values Table 4Showed the impact of Le = 0.1, 0.2, 0.3, 0.4, 0.5 on skin friction, Nusselt number and Sherwood numberLe0.10.0243902898882140.4181724529442350.2827861694877090.20.7154849500082360.4257700053547190.3139595624971930.30.8420884388573830.4306345386821800.3429579275832930.41.4008618906056580.4343375195179680.3657850762635310.52.0444733897029760.4373607237389140.383677446772655 Showed the impact of Le = 0.1, 0.2, 0.3, 0.4, 0.5 on skin friction, Nusselt number and Sherwood number Numerical outputs of skin friction, Nusselt number and Sherwood number for different Le values Table 5Showed the impact of NB = 0.1, 0.2, 0.3, 0.4, 0.5 on skin friction, Nusselt number and Sherwood numberNb0.10.0235046312110850.4238047677685310.3573412894248470.20.7237736885475890.4228117776167260.3771145952542660.30.8412720327271980.4226205440131360.3887067318010710.41.4224542141883570.4207365771954190.3969089238963720.52.0845796432370950.4179797897583470.403276460071806 Showed the impact of NB = 0.1, 0.2, 0.3, 0.4, 0.5 on skin friction, Nusselt number and Sherwood number Numerical outputs of skin friction, Nusselt number and Sherwood number for different NB values Conclusion Impact of second-grade nanofluid flow over horizontal stretching circular cylinder has many applications in heat exchangers, cooling towers and chimneys, pipelines, rocket bodies, aircraft fuselages, submarine hulls, offshore structures, and flow bodies of industrial sectors. The current study shows the heat and mass transport of second-grade nanofluid over horizontal stretching circular cylinder with thermal-concentration slip, variable density and chemical reactions. The objective of this study signifies the flow characteristics and thermal performance of second-grade nanofluid in large temperature differences between the surface and ambient fluid. In this situation, the density is assumed as exponential function of temperature. Using an established stream function and similarities modification, the coupled partial differential equations are converted into ordinary differential equations with important physical parameters. The resulting ordinary model is solved by applying average and central formula of finite difference approach with Newton–Raphson method for numerical outputs. The final graphical and numerical results of present research are calculated with the help of MATLAB software. The followings important results are discussed below. The physical study revealed that the velocity profile is increased with lower magnetic parameter because Lorenz force opposes the fluid motion and decreases the fluid velocity at higher magnetic parameter. The physical study revealed that the velocity profile is increased with lower magnetic parameter because Lorenz force opposes the fluid motion and decreases the fluid velocity at higher magnetic parameter. It is observed that stronger slip performance in fluid-temperature and concentration profiles is observed at each value of thermal and concentration parameters. The stronger convergence and accuracy in graphical results are developed under defined boundary condition. It is observed that stronger slip performance in fluid-temperature and concentration profiles is observed at each value of thermal and concentration parameters. The stronger convergence and accuracy in graphical results are developed under defined boundary condition. The mass concentration profile is enhanced with growing value of magnetic parameter, second-grade parameter, density parameter, chemical reaction parameter, thermal and concentration slip parameter. The mass concentration profile is enhanced with growing value of magnetic parameter, second-grade parameter, density parameter, chemical reaction parameter, thermal and concentration slip parameter. The numerical results revealed that the skin friction percentage is increased with large Prandtl, Lewis and Brownian diffusion. Enhancing percentage of Nusselt value is observed with higher value of Prandtl and Lewis number but reverse trend is observed for Brownian diffusion. The numerical results revealed that the skin friction percentage is increased with large Prandtl, Lewis and Brownian diffusion. Enhancing percentage of Nusselt value is observed with higher value of Prandtl and Lewis number but reverse trend is observed for Brownian diffusion. Enhancing Brownian motion parameter signifies the stronger increment in skin friction and mass transfer, while heat transfer decreases as NB is increased from 0.1 to 0.5. Stronger magnetic parameter reduces the streamline contour due to Lorentz force which opposes fluid motion. Enhancing Brownian motion parameter signifies the stronger increment in skin friction and mass transfer, while heat transfer decreases as NB is increased from 0.1 to 0.5. Stronger magnetic parameter reduces the streamline contour due to Lorentz force which opposes fluid motion. The stronger magnitude of isothermal contours is observed at higher magnetic force Mf = 1.2 and chemical reaction Cr = 1.0. The increasing isothermal contour is depicted at higher Cr = 0.7 but opposing results are observed in iso-concentration contour. The stronger magnitude of isothermal contours is observed at higher magnetic force Mf = 1.2 and chemical reaction Cr = 1.0. The increasing isothermal contour is depicted at higher Cr = 0.7 but opposing results are observed in iso-concentration contour. Future research directions In future work, this problem can be extended using hybrid nanofluid, Maxwell nanofluid, Casson nanofluid, Jeffry nanofluid, Williamson nanofluid and Prandtl-Eyring nanofluid with the impact of exponential variable density and slip flow along various geometries. Acknowledgements This research has been funded by Scientific Research Deanship at University of Ha’il – Saudi Arabia through project number <>. List of symbols Cartesian coordinates (m) Temperature at stretching surface (K) Magnetic field strength (A/m) Thermophoresis parameter Brownian motion parameter Magnetic parameter Local Sherwood number Wall concentration (kg/m3) Ambient concentration (kg/m3) Local generalized Reynolds number Dimensionless velocity at the surface Dimensionless velocity Dimensionless stream function Wall fluid temperature (K) Volumetric expansion parameter Thermal slip factor Concentration slip constant Chemical reaction parameter Greek symbols Thermal diffusivity (m2/s) Unit free concentration Kinematic fluid viscosity (m2/s) Particle mass density (Kg/m3) Heat capacity of particles (J/m3 K) Dimensionless temperature Solutal slip constant Buoyancy parameter Velocity components (m/s) Density parameter Thermal conductivity (W/mK) Concentration (mol/m^3) Prandtl number Second-grade parameter Local nusselt number Fluid temperature (K) Ambient temperature (K) Stretching velocity (m/s) Brownian diffusion (m2/s) Thermophoresis diffusion (m2/sK) Fluid density (Kgm-3) Specific heat (Jk/gK) Thermal slip constant Concentration slip factor Lewis parameter Similarity variable Dynamic fluid viscosity (kg/ms) Fluid density (Kg/m3) Heat capacity of fluid (J/m3 K) Stream function Ratio of heat capacity Lewise number Grashof number Author contributions Mhamed Benaissa; conceptualization, methodology: Zia Ullah; software, validation: Feysia Edosa Merga; formal analysis, investigation: Asmaa Farouk; writing-original draft, investigation: Mohamed S. Hamdy; writing-review and editing, funding acquisition: Noureddine Elboughdiri; resources: Djamel Ghernaout; software, methodology: Alsamani A.M. Salih; funding acquisition, methodology: Nidhal Ben Khedher; funding acquisition, methodology. All authors agreed for possible publication. Data availability The data that supports the findings of this study are available within the article. Declarations Ethics, consent to participate, and consent to publish declarations Not applicable. Clinical trial number Not applicable. Competing interests The authors declare no competing interests. Footnotes Publisher's Note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References Associated Data Data Availability Statement The data that supports the findings of this study are available within the article.