Safety assessment of the process Bandera Twin used to recycle post‐consumer PET into food contact materials Authors: EFSA Panel on Food Contact Materials (FCM), Claude Lambré, Riccardo Crebelli, Maria da Silva, Koni Grob, Ester Heath, Maria Rosaria Milana, Marja Pronk, Gilles Rivière, Mario Ščetar, Georgios Theodoridis, Els Van Hoeck, Nadia Waegeneers, Vincent Dudler, Constantine Papaspyrides, Maria de Fátima Tavares Poças, Katharina Volk, Evgenia Lampi Published: 2026 ABSTRACT AbstractThe EFSA Panel on Food Contact Materials (FCM) assessed the safety of the Bandera Twin recycling process (EU register number RECYC341). The input is washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post‐consumer PET containers, with no more than 5% PET from non‐food consumer applications. The flakes are extruded at high temperature and vacuum (step 2). Having examined the challenge test provided, the Panel concluded that the operating parameters to control the performance of the critical step 2 are temperature, pressure and ■■■■■. It was demonstrated that this recycling process ensures that the levels of migration of potential unknown contaminants into food are below the conservatively modelled migration and that therefore the recycled PET obtained from the process is not of safety concern when used at up to (i) 9% for the manufacture of materials and articles for contact with drinking water, for long‐term storage at room temperature, with or without hot‐fill; (ii) 30% for the manufacture of materials and articles for contact with milk, other liquid milk‐based products, non‐alcoholic beverages (other than drinking water) and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature, with or without hot‐fill); and (iii) 100% for the manufacture of materials and articles for contact with all types of foodstuffs other than drinking water, milk, liquid milk‐based products and non‐alcoholic beverages, and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. Articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation. INTRODUCTION Background and Terms of Reference Background Recycled plastic materials and articles shall only be placed on the market if the recycled plastic is from an authorised recycling process. Before a recycling process is authorised, the European Food Safety Authority (EFSA)'s opinion on its safety is required. This procedure has been established in Articles 17 and 18 of Commission Regulation (EU) 2022/1616 1 on recycled plastic materials intended to come into contact with foods. More specifically, according to Article 18 of Commission Regulation (EU) 2022/1616 on recycled plastic materials intended to come into contact with foods, EFSA is required to carry out risk assessments on the risks originating from the migration of substances from recycled food contact plastic materials and articles into food, to evaluate the microbiological safety of these materials and articles and to deliver a scientific opinion on the recycling process examined. According to this procedure, the process developers submit applications to the competent authorities of Member States, which transmit the applications to EFSA for evaluation. In this case, EFSA received an application from the Italian competent authority (Ministero della Salute), for evaluating the recycling process Bandera Twin, European Union (EU) register No RECYC341. The request has been registered in the EFSA's register of received questions under the number EFSA‐Q‐2023‐00480. The dossier was submitted on behalf of Costruzioni Meccaniche Luigi Bandera S.p.A., Corso Sempione 120, 21052 Busto Arsizio, Italy (see ‘Documentation as provided to EFSA’). Terms of Reference The Italian competent authority (Ministero della Salute) requested the safety evaluation of the recycling process Bandera Twin, in compliance with Article 17 of Commission Regulation (EU) 2022/1616. The recycling process uses the recycling technology number 1 of the list of suitable recycling technologies of Table 1 of Annex 1 of Commission Regulation (EU) 2022/1616. DATA AND METHODOLOGIES Data The applicant submitted a confidential and a non‐confidential version of a dossier, following EFSA's ‘Scientific Guidance on the criteria for the evaluation and on the preparation of applications for the safety assessment of post‐consumer mechanical PET recycling processes intended to be used for manufacture of materials and articles in contact with food’ (EFSA CEP Panel, 2024) and EFSA's ‘Administrative guidance for the preparation of applications for the authorisation of individual recycling processes to produce recycled plastics materials and articles intended to come into contact with food’ (EFSA, 2024). Additional information was received from the applicant during the assessment process, in response to requests from EFSA sent on 24 September 2024, 20 May 2025 and 21 January 2026 (see ‘Documentation provided to EFSA’). In addition, a technical hearing with the applicant was held on 14 January 2026. In accordance with Art. 38 of the Regulation (EC) No 178/2002 2 and taking into account the protection of confidential information and the personal data in accordance with Articles 39 to 39e of the same Regulation, and of the Decision of the EFSA's Executive Director laying down practical arrangements concerning transparency and confidentiality, 3 the non‐confidential version of the dossier has been published on Open.EFSA. 4 According to Art. 32c(2) of Regulation (EC) No 178/2002 and to the Decision of EFSA's Executive Director laying down the practical arrangements on pre‐submission phase and public consultations4, EFSA carried out a public consultation on the non‐confidential version of the application from 17 September to 08 October 2024, for which no comments were received. The following information on the recycling process was provided by the applicant and used for the evaluation (EFSA, 2024; EFSA CEP Panel, 2024): –Recycling process,–Determination of the decontamination efficiency of the recycling process,–Table of operating parameters,–Self‐evaluation of the recycling process. –Recycling process, Recycling process, –Determination of the decontamination efficiency of the recycling process, Determination of the decontamination efficiency of the recycling process, –Table of operating parameters, Table of operating parameters, –Self‐evaluation of the recycling process. Self‐evaluation of the recycling process. Methodologies The risks associated with the use of recycled plastic materials and articles in contact with food come from the possible migration of chemicals into the food in amounts that would endanger human health. The quality of the input, the efficiency of the recycling process to remove contaminants as well as the intended use of the recycled plastic are crucial points for the risk assessment (EFSA CEP Panel, 2024). The criteria for the safety evaluation of a mechanical recycling process to produce recycled PET intended to be used for the manufacture of materials and articles in contact with food are described in the scientific guidance developed by the EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (EFSA CEP Panel, 2024). The principle of the evaluation is to apply the decontamination efficiency of a recycling process, obtained from a challenge test with surrogate contaminants, to a reference contamination level for post‐consumer PET, conservatively set at 3 mg/kg PET for contaminants resulting from possible misuse. The resulting residual concentration of each surrogate contaminant in recycled PET (Cres) is compared with a modelled concentration of the surrogate contaminants in PET (Cmod). This Cmod is calculated using generally recognised conservative migration models so that the related migration does not give rise to a dietary exposure exceeding 0.0025 μg/kg body weight (bw) per day (i.e. the human exposure threshold value for chemicals with structural alerts for genotoxicity), below which the risk to human health would be negligible, considering different dietary exposure scenarios (EFSA CEP Panel, 2024). If the Cres is not higher than the Cmod, the recycled PET manufactured by such recycling process is not considered to be of safety concern for the defined conditions of use (EFSA CEP Panel, 2024). The assessment was conducted in line with the principles described in the EFSA Guidance on transparency in the scientific aspects of risk assessment, considering the relevant guidance from the EFSA Scientific Committee (EFSA, 2009). ASSESSMENT General information 5 According to the applicant, the recycling process Bandera Twin is intended to recycle food grade PET containers. The recycled PET is intended to be used for the manufacture of materials and articles for direct contact with food under a variety of conditions, as specified by the applicant in the technical dossier. 6 The final articles are not intended to be used in microwave or conventional ovens. Description of the process General description 7 The recycling process Bandera Twin produces recycled PET using PET materials from post‐consumer collection systems. 8 Input In step 1, post‐consumer PET is processed into hot caustic‐washed and dried flakes. In step 1, post‐consumer PET is processed into hot caustic‐washed and dried flakes. In step 1, post‐consumer PET is processed into hot caustic‐washed and dried flakes. Decontamination and production of recycled PET material In step 2, the flakes are extruded at high temperature and vacuum. In step 2, the flakes are extruded at high temperature and vacuum. In step 2, the flakes are extruded at high temperature and vacuum. The operating conditions of the process have been provided to EFSA. Characterisation of the input 9 According to the applicant, the input material consists of hot caustic/surfactant‐washed and dried flakes obtained from PET materials, e.g. bottles, previously used for food packaging, from post‐consumer collection systems.7 A small fraction may originate from non‐food applications. According to the applicant, the proportion will be no more than 5%, as specified in Article 7 and Table 1 of Annex I of Commission Regulation (EU) 2022/1616. Technical specifications on the washed and dried flakes are provided, such as on physical properties and on residual contents of poly(vinyl chloride) (PVC), glue, polyolefins, other residual plastics (e.g. polycarbonate (PC), polystyrene (PS)), cellulose (paper, wood), metals, inert content and total contamination (see Appendix A). Bandera Twin process Description of the main step 10 The process flow diagram, as provided by the applicant, is reported in Figure 1. Extrusion (step 2): The flakes are melted in a twin‐screw extruder under vacuum, high temperature and a defined ■■■■■. The parameter of ■■■■■ covers the ■■■■■ and the ■■■■■, the ■■■■■ and the ■■■■■. ■■■■■ ■■■■■, implementing the underlying principles on twin‐screw extruders ■■■■■ The decontaminated melt is then processed into pellets or sheets. Process flow diagram of the Bandera Twin process (provided by the applicant). The process is run under defined operating parameters 11 of temperature, pressure and ■■■■■. The operating parameters are automatically controlled and locked by a data locking system; in case of deviations from the acceptable parameter values or ranges, the exiting material is not used for direct food contact applications. 12 According to the applicant, the final products of the process are checked against technical requirements, such as intrinsic viscosity, colour and black spots. 13 Decontamination efficiency of the recycling process 14 To demonstrate the decontamination efficiency of the recycling process Bandera Twin, a challenge test performed at industrial scale on step 2 was submitted to EFSA. PET flakes were contaminated with toluene, chlorobenzene, phenylcyclohexane, benzophenone and methyl stearate, selected as surrogates in agreement with the EFSA Scientific Guidance (EFSA CEP Panel, 2024) and in accordance with the recommendations of the US Food and Drug Administration (FDA, 2021). For the preparation of the contaminated PET flakes, 300 kg PET flakes were mixed with a solution of the surrogates and stored for 7 days at 50°C with continuous mixing. The contaminated flakes were then rinsed with 10% ethanol. After centrifugation, the concentrations of the surrogates were determined in the flakes. The decontamination efficiency was calculated from the concentration differences of the surrogate substances in the washed contaminated flakes before and the decontaminated pellets after the extruder. The results are summarised in Table 1. TABLE 1Efficiency of the decontamination in the Bandera Twin challenge test.SurrogatesConcentration of surrogates before step 2 (mg/kg PET)Concentration of surrogates after step 2 (mg/kg PET)Decontamination efficiency (%) Toluene 863.549.294.3 Chlorobenzene 845.061.492.7 Phenylcyclohexane 546.0109.679.9 Benzophenone 667.9353.447.1 Methyl stearate 625.8245.460.8Abbreviation: PET, poly(ethylene terephthalate). Efficiency of the decontamination in the Bandera Twin challenge test. Abbreviation: PET, poly(ethylene terephthalate). Discussion Considering the high temperatures used during the process, the possibility of contamination by microorganisms can be discounted. Therefore, this evaluation focuses on the chemical safety of the final product. Specifications on the input material (i.e. washed and dried flakes, step 1) are listed in Appendix A. The flakes are produced from PET containers, e.g. bottles, previously used for food packaging, collected through post‐consumer collection systems. However, a small fraction may originate from non‐food applications, such as bottles for soap, mouthwash or kitchen hygiene agents. According to the applicant, the collection system and the sorting are managed in such a way that this fraction will be no more than 5% in the input, 15 as recommended by the EFSA CEP Panel in its Guidance (EFSA CEP Panel, 2024). The process, based on extrusion (step 2), is adequately described. The operating parameters of temperature, pressure and ■■■■■ have been provided to EFSA. A challenge test to measure the decontamination efficiency was conducted at industrial scale on process step 2 (extrusion). The Panel considered that it was performed correctly according to the recommendations of the EFSA Guidance (EFSA, CEP Panel, 2024). The decontamination of the material in the extruder is critical and depends on the ■■■■■, the pressure and the temperature. Consequently, these parameters are to be controlled to guarantee the efficiency of the decontamination. Extruders of different sizes are intended to be used at ■■■■■. To ensure at least the same decontamination efficiency as in the challenge test, the ■■■■■ must be equal to or above that of the challenge test; under industrial production conditions, this ratio is typically higher. ■■■■■, implementing the underlying principles on twin‐screw extruders ■■■■■. The Panel concluded that the approach is adequate. The decontamination efficiencies obtained for each surrogate, ranging from 47.1% to 94.3%, have been used to calculate the residual concentrations of potential unknown contaminants in PET (Cres). By applying the decontamination percentages to the reference contamination level of 3 mg/kg PET, the Cres values shown in Tables 2, 3, 4 were obtained. According to the evaluation principles (EFSA CEP Panel, 2024), the dietary exposure must not exceed 0.0025 μg/kg bw per day, below which the risk to human health is considered negligible. The Cres value should not exceed the modelled concentration in PET (Cmod) that, after 1 year at 25°C, results in a migration giving rise to a dietary exposure of 0.0025 μg/kg bw per day. The recycled PET is intended to be used for the manufacture of a variety of articles used under a range of different conditions. 16 The Panel restricted the evaluation of uses to those in line with the default considerations of 1 year at 25°C outlined in the guidance (EFSA CEP Panel, 2024). Therefore, only three scenarios of use have been evaluated, as outlined below. The relationship between the key parameters for the evaluation scheme is reported in Appendix B. Exposure scenario A: A maximum dietary exposure of 0.0025 μg/kg bw/day corresponds to a maximum migration of 0.0481 μg/kg food (= 5 × 0.00962 μg/kg) or 0.0962 μg/kg food (= 10 × 0.00962 μg/kg), depending on the molar mass of a contaminant substance, 17 into infant food 18 and has been used to calculate Cmod (EFSA CEP Panel, 2024). Cres reported in Table 2 is calculated for 9% recycled PET.Exposure scenario B: A maximum dietary exposure of 0.0025 μg/kg bw/day corresponds to a maximum migration of 0.156 μg/kg food (= 5 × 0.0312 μg/kg) or 0.312 μg/kg food (= 10 × 0.0312 μg/kg), depending on the molar mass of a contaminant substance, 19 into toddler's food and has been used to calculate Cmod (EFSA CEP Panel, 2024). Cres reported in Table 3 is calculated for 30% recycled PET.Exposure scenario C: A maximum dietary exposure of 0.0025 μg/kg bw/day corresponds to a maximum migration of 0.625 μg/kg food (= 5 × 0.125 μg/kg) or 1.25 μg/kg food (= 10 × 0.125 μg/kg), depending on the molar mass of a contaminant substance, 20 into adult's food and has been used to calculate Cmod (EFSA CEP Panel, 2024). Cres reported in Table 4 is calculated for 100% recycled PET. Exposure scenario A: A maximum dietary exposure of 0.0025 μg/kg bw/day corresponds to a maximum migration of 0.0481 μg/kg food (= 5 × 0.00962 μg/kg) or 0.0962 μg/kg food (= 10 × 0.00962 μg/kg), depending on the molar mass of a contaminant substance, 17 into infant food 18 and has been used to calculate Cmod (EFSA CEP Panel, 2024). Cres reported in Table 2 is calculated for 9% recycled PET. Exposure scenario A: A maximum dietary exposure of 0.0025 μg/kg bw/day corresponds to a maximum migration of 0.0481 μg/kg food (= 5 × 0.00962 μg/kg) or 0.0962 μg/kg food (= 10 × 0.00962 μg/kg), depending on the molar mass of a contaminant substance, 17 into infant food 18 and has been used to calculate Cmod (EFSA CEP Panel, 2024). Cres reported in Table 2 is calculated for 9% recycled PET. Exposure scenario B: A maximum dietary exposure of 0.0025 μg/kg bw/day corresponds to a maximum migration of 0.156 μg/kg food (= 5 × 0.0312 μg/kg) or 0.312 μg/kg food (= 10 × 0.0312 μg/kg), depending on the molar mass of a contaminant substance, 19 into toddler's food and has been used to calculate Cmod (EFSA CEP Panel, 2024). Cres reported in Table 3 is calculated for 30% recycled PET. Exposure scenario B: A maximum dietary exposure of 0.0025 μg/kg bw/day corresponds to a maximum migration of 0.156 μg/kg food (= 5 × 0.0312 μg/kg) or 0.312 μg/kg food (= 10 × 0.0312 μg/kg), depending on the molar mass of a contaminant substance, 19 into toddler's food and has been used to calculate Cmod (EFSA CEP Panel, 2024). Cres reported in Table 3 is calculated for 30% recycled PET. Exposure scenario C: A maximum dietary exposure of 0.0025 μg/kg bw/day corresponds to a maximum migration of 0.625 μg/kg food (= 5 × 0.125 μg/kg) or 1.25 μg/kg food (= 10 × 0.125 μg/kg), depending on the molar mass of a contaminant substance, 20 into adult's food and has been used to calculate Cmod (EFSA CEP Panel, 2024). Cres reported in Table 4 is calculated for 100% recycled PET. Exposure scenario C: A maximum dietary exposure of 0.0025 μg/kg bw/day corresponds to a maximum migration of 0.625 μg/kg food (= 5 × 0.125 μg/kg) or 1.25 μg/kg food (= 10 × 0.125 μg/kg), depending on the molar mass of a contaminant substance, 20 into adult's food and has been used to calculate Cmod (EFSA CEP Panel, 2024). Cres reported in Table 4 is calculated for 100% recycled PET. TABLE 2Decontamination efficiencies from the challenge test, residual concentrations of the surrogates (Cres) related to the reference contamination level and calculated concentrations of the surrogates in PET (Cmod) corresponding to a modelled migration of 0.0481 μg/kg food or 0.0962 μg/kg food (Scenario A) after 1 year at 25°C.SurrogatesDecontamination efficiency (%)Cres for 9% rPET (mg/kg PET)Cmod (mg/kg PET) Toluene 94.30.020.04 Chlorobenzene 92.70.020.05 Phenylcyclohexane 79.90.050.13 Benzophenone 47.10.140.15 Methyl stearate 60.80.110.29Abbreviations: PET, poly(ethylene terephthalate); rPET, recycled poly(ethylene terephthalate). Decontamination efficiencies from the challenge test, residual concentrations of the surrogates (Cres) related to the reference contamination level and calculated concentrations of the surrogates in PET (Cmod) corresponding to a modelled migration of 0.0481 μg/kg food or 0.0962 μg/kg food (Scenario A) after 1 year at 25°C. Abbreviations: PET, poly(ethylene terephthalate); rPET, recycled poly(ethylene terephthalate). TABLE 3Decontamination efficiencies from the challenge test, residual concentrations of the surrogates (Cres) related to the reference contamination level and calculated concentrations of the surrogates in PET (Cmod) corresponding to a modelled migration of 0.156 μg/kg food or 0.312 μg/kg food (Scenario B) after 1 year at 25°C.SurrogatesDecontamination efficiency (%)Cres for 30% rPET (mg/kg PET)Cmod (mg/kg PET) Toluene 94.30.050.13 Chlorobenzene 92.70.070.15 Phenylcyclohexane 79.90.180.42 Benzophenone 47.10.480.49 Methyl stearate 60.80.350.95Abbreviations: PET, poly(ethylene terephthalate); rPET, recycled poly(ethylene terephthalate). Decontamination efficiencies from the challenge test, residual concentrations of the surrogates (Cres) related to the reference contamination level and calculated concentrations of the surrogates in PET (Cmod) corresponding to a modelled migration of 0.156 μg/kg food or 0.312 μg/kg food (Scenario B) after 1 year at 25°C. Abbreviations: PET, poly(ethylene terephthalate); rPET, recycled poly(ethylene terephthalate). TABLE 4Decontamination efficiencies from the challenge test, residual concentrations of the surrogates (Cres) related to the reference contamination level and calculated concentrations of the surrogates in PET (Cmod) corresponding to a modelled migration of 0.625 μg/kg food or 1.25 μg/kg food (Scenario C) after 1 year at 25°C.SurrogatesDecontamination efficiency (%)Cres for 100% rPET (mg/kg PET)Cmod (mg/kg PET) Toluene 94.30.170.51 Chlorobenzene 92.70.220.60 Phenylcyclohexane 79.90.601.69 Benzophenone 47.11.591.96 Methyl stearate 60.81.183.82Abbreviations: PET, poly(ethylene terephthalate); rPET, recycled poly(ethylene terephthalate). Decontamination efficiencies from the challenge test, residual concentrations of the surrogates (Cres) related to the reference contamination level and calculated concentrations of the surrogates in PET (Cmod) corresponding to a modelled migration of 0.625 μg/kg food or 1.25 μg/kg food (Scenario C) after 1 year at 25°C. Abbreviations: PET, poly(ethylene terephthalate); rPET, recycled poly(ethylene terephthalate). On the basis of the provided data from the challenge test and the applied conservative assumptions, the Panel considered that under the given operating conditions the recycling process Bandera Twin is able to ensure that the levels of migration of unknown contaminants from the recycled PET into food, as mentioned above, are below the conservatively modelled migration. related to exposure scenario A (EFSA FCM Panel, 2024). At this level, the risk to human health is considered negligible when the recycled PET is used at up to 9% to produce materials and articles intended for contact with infant formula and drinking water that could be used to reconstitute infant formula, for long‐term storage at room temperature or below, with or without hot‐fill.related to exposure scenario B (EFSA FCM Panel, 2024). At this level, the risk to human health is considered negligible when the recycled PET is used at up to 30% to produce materials and articles intended for contact with milk, other liquid milk‐based products, non‐alcoholic beverages (other than drinking water) and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill.related to exposure scenario C (EFSA FCM Panel, 2024). At this level, the risk to human health is considered negligible when the recycled PET is used at up to 100% to produce materials and articles intended for contact with all types of foodstuffs other than drinking water, milk, liquid milk‐based products and non‐alcoholic beverages, and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. related to exposure scenario A (EFSA FCM Panel, 2024). At this level, the risk to human health is considered negligible when the recycled PET is used at up to 9% to produce materials and articles intended for contact with infant formula and drinking water that could be used to reconstitute infant formula, for long‐term storage at room temperature or below, with or without hot‐fill. related to exposure scenario A (EFSA FCM Panel, 2024). At this level, the risk to human health is considered negligible when the recycled PET is used at up to 9% to produce materials and articles intended for contact with infant formula and drinking water that could be used to reconstitute infant formula, for long‐term storage at room temperature or below, with or without hot‐fill. related to exposure scenario B (EFSA FCM Panel, 2024). At this level, the risk to human health is considered negligible when the recycled PET is used at up to 30% to produce materials and articles intended for contact with milk, other liquid milk‐based products, non‐alcoholic beverages (other than drinking water) and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. related to exposure scenario B (EFSA FCM Panel, 2024). At this level, the risk to human health is considered negligible when the recycled PET is used at up to 30% to produce materials and articles intended for contact with milk, other liquid milk‐based products, non‐alcoholic beverages (other than drinking water) and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. related to exposure scenario C (EFSA FCM Panel, 2024). At this level, the risk to human health is considered negligible when the recycled PET is used at up to 100% to produce materials and articles intended for contact with all types of foodstuffs other than drinking water, milk, liquid milk‐based products and non‐alcoholic beverages, and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. related to exposure scenario C (EFSA FCM Panel, 2024). At this level, the risk to human health is considered negligible when the recycled PET is used at up to 100% to produce materials and articles intended for contact with all types of foodstuffs other than drinking water, milk, liquid milk‐based products and non‐alcoholic beverages, and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. CONCLUSIONS The Panel considered that the process Bandera Twin is adequately characterised and that the critical step used to recycle the PET flakes into decontaminated PET has been identified. Having examined the challenge test provided, the Panel concluded that the extrusion (step 2) is critical for the decontamination efficiency. The parameters to control the process performance are pressure, temperature and ■■■■■ as specified in Appendix C. The Panel concluded that the recycling process is capable of reducing contamination of post‐consumer food contact PET to a concentration that does not give rise to concern for a risk to human health if: it is operated under conditions that are at least as severe as those applied in the challenge test used to measure the decontamination efficiency of the process;the input material of the process is washed and dried post‐consumer PET flakes originating from materials and articles that have been manufactured in accordance with the EU legislation on food contact materials and contain no more than 5% of PET from non‐food consumer applications.the recycled PET obtained from the process Bandera Twin is used at up to 9% for the manufacture of materials and articles for contact with infant formula and drinking water, for long‐term storage at room temperature, with or without hot‐fill.up to 30% for the manufacture of materials and articles for contact with milk, other liquid milk‐based products, non‐alcoholic beverages (other than drinking water) and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature, with or without hot‐fill.up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs other than infant formula, drinking water, milk, liquid milk‐based products and non‐alcoholic beverages, and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. it is operated under conditions that are at least as severe as those applied in the challenge test used to measure the decontamination efficiency of the process; it is operated under conditions that are at least as severe as those applied in the challenge test used to measure the decontamination efficiency of the process; the input material of the process is washed and dried post‐consumer PET flakes originating from materials and articles that have been manufactured in accordance with the EU legislation on food contact materials and contain no more than 5% of PET from non‐food consumer applications. the input material of the process is washed and dried post‐consumer PET flakes originating from materials and articles that have been manufactured in accordance with the EU legislation on food contact materials and contain no more than 5% of PET from non‐food consumer applications. the recycled PET obtained from the process Bandera Twin is used at up to 9% for the manufacture of materials and articles for contact with infant formula and drinking water, for long‐term storage at room temperature, with or without hot‐fill.up to 30% for the manufacture of materials and articles for contact with milk, other liquid milk‐based products, non‐alcoholic beverages (other than drinking water) and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature, with or without hot‐fill.up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs other than infant formula, drinking water, milk, liquid milk‐based products and non‐alcoholic beverages, and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. the recycled PET obtained from the process Bandera Twin is used at up to 9% for the manufacture of materials and articles for contact with infant formula and drinking water, for long‐term storage at room temperature, with or without hot‐fill.up to 30% for the manufacture of materials and articles for contact with milk, other liquid milk‐based products, non‐alcoholic beverages (other than drinking water) and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature, with or without hot‐fill.up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs other than infant formula, drinking water, milk, liquid milk‐based products and non‐alcoholic beverages, and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. up to 9% for the manufacture of materials and articles for contact with infant formula and drinking water, for long‐term storage at room temperature, with or without hot‐fill. up to 9% for the manufacture of materials and articles for contact with infant formula and drinking water, for long‐term storage at room temperature, with or without hot‐fill. up to 30% for the manufacture of materials and articles for contact with milk, other liquid milk‐based products, non‐alcoholic beverages (other than drinking water) and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature, with or without hot‐fill. up to 30% for the manufacture of materials and articles for contact with milk, other liquid milk‐based products, non‐alcoholic beverages (other than drinking water) and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature, with or without hot‐fill. up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs other than infant formula, drinking water, milk, liquid milk‐based products and non‐alcoholic beverages, and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs other than infant formula, drinking water, milk, liquid milk‐based products and non‐alcoholic beverages, and solid foods specifically intended for infants and toddlers, for long‐term storage at room temperature or below, with or without hot‐fill. The final articles made of this recycled PET are not intended to be used in microwave or conventional ovens and such uses are not covered by this evaluation. RECOMMENDATION The Panel recommended periodic verification that the input to be recycled originates from materials and articles that have been manufactured in accordance with the EU legislation on food contact materials and that the proportion of PET from non‐food consumer applications is no more than 5%. This adheres to good manufacturing practice and the Commission Regulation (EU) 2022/1616. Critical steps in recycling should be monitored and kept under control. In addition, supporting documentation should be available on how it is ensured that the critical steps are operated under conditions at least as severe as those in the challenge test used to measure the decontamination efficiency of the process. DOCUMENTATION AS PROVIDED TO EFSA Dossier ‘Bandera Twin’, May 2024. Submitted on behalf of Costruzioni Meccaniche Luigi Bandera S.p.A, Italy. Additional information, March 2025. Submitted on behalf of Costruzioni Meccaniche Luigi Bandera S.p.A, Italy. Additional information, October 2025. Submitted on behalf of Costruzioni Meccaniche Luigi Bandera S.p.A, Italy. Additional information, March 2026. Submitted on behalf of Costruzioni Meccaniche Luigi Bandera S.p.A, Italy. ABBREVIATIONS body weight Panel on Food Contact Materials, Enzymes and Processing Aids modelled concentration in PET residual concentrations in PET Panel on Food Contact Materials ■■■■■ ■■■■■ polycarbonate poly(ethylene terephthalate) polystyrene poly(vinyl chloride) recycled poly(ethylene terephthalate) REQUESTOR Italian Competent Authority (Ministero della Salute) QUESTION NUMBER EFSA‐Q‐2023‐00480 COPYRIGHT FOR NON‐EFSA CONTENT EFSA may include images or other content for which it does not hold copyright. In such cases, EFSA indicates the copyright holder and users should seek permission to reproduce the content from the original source. PANEL MEMBERS Claude Lambré, Riccardo Crebelli, Maria de Silva, Koni Grob, Ester Heath, Evgenia Lampi, Maria Rosaria Milana, Marja Pronk, Gilles Rivière, Mario Ščetar, Georgios Theodoridis, Els Van Hoeck and Nadia Waegeneers. WAIVER In accordance with Article 21 of the Decision of the Executive Director on Competing Interest Management a waiver was granted to an expert of the Working Group. Pursuant to Article 21(6) of the aforementioned Decision, the concerned expert was allowed to take part in the preparation and in the discussion of the scientific output but was not allowed to take up the role of rapporteur within that time frame. Any competing interests are recorded in the respective minutes of the meetings of the FCM Panel Working Group on Recycling Plastics. LEGAL NOTICE The published scientific output includes information items that have been redacted, in accordance with the confidentiality requests submitted by the applicant, pending a decision thereon by EFSA. Redactions may be subject to review once a decision on such confidentiality requests is taken by EFSA.